Search Documents

By Gregory E. Korbin

The effectiveness of pre-reinforcement as an immediate stabilization measure as well as its contribution to the permanent stabilization of a tunnel were studied through the use of physical (Figure 1) and numerical models (1). Physical models were designed for the investigation of two pre-reinforcement systems: first, reinforcing far ahead of the main excavation (Figure 2); second, spiling reinforcement ahead of the face (Figure 3). In both cases, the use of reinforcement was responsible for permanently stabilizing an otherwise unstable opening. Data from the physical models were used to calibrate a numerical model from which additional information on long term behavior, methods to account for the capacity of a pre-reinforcement system, and the mechanisms involved were ascertained. These studies indicated that pre-reinforcement can stabilize a rock mass effectively as it reduces deformations and thereby deterioration due to strain softening, provides rock mass confinement leading to increased available strength, and maintains rock arch continuity allowing for increased tangential stress in the immediate vicinity of the opening. Field studies verified the capacity of spiling reinforcement to restrain initial deformations.

Jan 1, 1976

By I. L. Jennings

In most industrialized countries, the largest element of the mining industry in physical volume is that devoted to the extraction and processing of materials for use as construction aggregates. Required for all developments in industry and commerce, power and transportation, and housing and public services, their use is so widespread that possible sources are exploited throughout all geographic regions, as close as possible to the point of use. Thus, it is also the most frequently encountered form of mining throughout the world. These materials come from four main sources:- (a) Excavation of unconsolidated deposits of sand and gravel (b) Stone quarrying. (c) Processing of slags and other mineral wastes. (d) Manufacturing from clays and shales by heat fusion. The major uses are in: (a) Portland cement concrete, that most versatile of construction materials, including the many concrete products in current use. (b) Asphalt cement concrete; widely employed for paving roads, parking lots, airfields, etc. (c) Foundation materials, such as road base, granular backfills, railway ballast, etc.

Jan 1, 1968

By D. M. Thayer

In the last decade public awareness of the need for pollution abatement has increased greatly. The concern that had been previously shared by local and state conservation groups has spread to create a national concern for preservation of our non-polluted environmental assets and regeneration of those that have been wasted. Because other current matters such as inflation, civil rights,' tax reform and the Vietnam situation have been the object of most national concern, an extremely strong national pressure base has not been brought to bear on the pollution control crisis. Yes, the word is crisis, for in many areas pollution is of critical concern. One has only to look at Lake Erie, the skies about our major urban areas and many of our major rivers and streams to see this crisis These are not situations that can be corrected overnight. We are faced with two basic problems that should be attacked simultaneously: (1) Cleaning up the present sources of pollution and (2) preventing the generation of new pollution sources. What approach should be taken? As in any engineering problem, the limits must be well defined before a final solution is attempted. Pollution must be defined on a national basis. This means that basic Federal legislation and control is necessary. This should reduce any competitive advantage that can presently be gained by movement of operations from one state or geographical area to another on the basis of differences in local legislation .and enforcement. By giving real numbers as guidelines, selective enforcement can be avoided. As a starting point, for a definition of pollution let us use the following - "Any change in the environment occurring from other than natural causes." This definition may not be satisfactory to all but surely we must be somewhat dramatic in our statements to counteract the present prevailing philosophy. Our statement of this philosophy - "At what level of pollution can we afford to operate?" On the basis of our general definition we would like to state what we feel should be the philosophical statement - "How little can we change our physical environment as a result of operations?"

Jan 1, 1970

By J. C. Agarwal

A significant portion of the, coal mined by U. S. Steel is beneficiated to upgrade the quality of the resultant coke to meet blast-furnace requirements. Primarily because of degradation from modern mechanized mining methods, a considerable quantity of the coal to be beneficiated is in the 1/4-inch by 100-mesh size range. In the cleaning plants, this coal is usually cleaned on concentrating tables and then mechanically dewatered in solid-bowl centrifuges to 9 to 14 percent water. At some plants, to further decrease the amount of water shipped with coal, and to improve the coking characteristics of the coal at its destination, mechanical dewatering is followed by thermal drying. At U. S. Steel's-Alpheus preparation plant at Gary, West Virginia, approximately 50 percent of the total coal produced is in this fine size range, and two fluidized-bed dryers are used for the thermal drying step. The two fluidized-bed dryers are 14 feet in diameter and were designed by the Dorr-Oliver Company. Although the original design called for a rate of drying equivalent to 37 tons, of moisture per hour, presently they are removing twice that amount. This paper describes, the major problems encountered' in operating these dryers at the present, high capacities and how they were overcome.

Jan 1, 1963

By J. A. Wallace

U. S. Steel's coal mining research activities are directed toward providing new or improved hardware and techniques to increase productivity or reduce cost. Because more than 80 percent of U. S. Steel's coal production is obtained from continuous miner sections, most of our research efforts are focused upon that mining system. Current and historical time study data show that our continuous miners only operate about 30 percent of the available face time. This limited equipment utilization is the result of the delays or interferences imposed by the non-coal-cutting phases of the continuous mining cycle. The most time consuming of these delays are: waiting-on-roof-support, tramming between alternate work locations, waiting-on-haulage-capacity, and in some mines waiting for excessive methane concentrations to clear. Because waiting on roof support is our most time consuming delay, several programs are underway simultaneously to address this problem. In one of these we are developing a patented microprocessor-based control method and apparatus to improve roof drilling performance. This increase is attained by using the microprocessor to adjust electrohydraulic valves which control drill thrust and rotation speed. The microprocessor is designed to continuously search for an optimum combination of thrust and drill rpm to maximize penetration rate at all times.

Jan 1, 1979

By G. A. Hufford

The cutoff grade applied to a disseminated orebody mined by open pit affects both the waste ratio, hence the cost of producing ore, and the ore grade, hence the quantity of metal recovered. As such it has a significant impact not only on the annual profit or loss, but also on the life of a mining property. Cutoff Grade Strategies Some commonly used objectives in calculating cutoff grades are as follows: Minimize Unit Cost of Product (1) This is found by adding all costs associated with each possible cutoff such as mining, processing, and marketing. This is divided by the quantity of marketable product obtained at each cutoff grade, then finding the minimum. Because the market value of the product does not enter the calculation it has no effect on this strategy: the same cutoff is selected in good times and bad.

Jan 1, 1986

By R. W. Wotring

Mr. Chairman, Officers, Members and Guests of the AIME, I want to express my appreciation for the privilege of being on your program at this meeting. Coal mining, in recent years, has become much more competitive than it formerly was. To stay in business, it has been necessary for coal mines to mechanize. This, in itself, has not been enough for after one has mechanized his mine, he must keep replacing the equipment with the latest type and model machines. We, at Olga, have been doing this very thing for the past several years. Olga No. 2 Mine is located at Caretta, West Virginia, in McDovell County, about twelve miles south of Welch, It is a shaft mine, operating in the No. 4 Pocahontas seam. The thickness in the area, we are presently mining, varies from five to six feet. In some areas the immediate roof is slate, ranging in thickness from a few inches to four and five feet; in other places, the sandstone lies on top of the coal, This sandstone is about twenty-five feet thick.

Jan 1, 1961

By Alejandro Prieto

Traditionally, Mexico has been a mining country. This industry has played a very important role in our country's development, creating jobs, integrating geographical regions - generally very remote from urban communities - and, an essential factor in our present day economy, generating an influx of foreign currency. The Fluorspar mining industry's development started in the 1920?s, but it was not until World War II that its exploitation became consistent and started growing. During the last few years, Mexico has become the world's leading producer, with an annual output of more than one million tons, which directly generates over 3,000 jobs. The actual proven reserves can guarantee fifty years of production at this same annual rate, and it is due to this fact that the producers have not increased their reserves. However, there is concrete information of the existence of several deposits, extending from the northern border to the gulf of Mexico, forming the "Fluorspar Belt? in Mexico.

Jan 1, 1986

By H. Copur

Roadheaders offer a unique capability and flexibility for the excavation of soft to medium strength rock formations, therefore, are very attractive in underground mining and tunneling operations. This paper reviews the importance, technological developments and application limits of roadheaders based on the case histories, which are compiled in a database including different roadheaders in various geological conditions. The paper also discusses the database and empirical performance prediction studies regarding instantaneous cutting rates and bit consumption rates.

Jan 1, 1998

By M. G. Schulz

Mining of molybdenum at Questa, New Mexico has been accomplished by block cave methods since August, 1983. As caving progresses, a periodic geologic evaluation is made of the rock-types present in finger raises on the Grizzly Level of the mine. The production maturity of the cave can be monitored by relating this data to geologic cross-sections through the ore body. The draw point mapping program is a simple and effective tool that is used in making draw control decisions at Questa.

Jan 1, 1985

By Robert G. Beverly

The presence of radioactivity in uranium mill wastes has resulted in somewhat unique waste disposal methods. In addition to the common problems of disposing of large quantities of solid wastes, neutralizing acids, minimizing dissolved heavy metals, and clarifying all liquid effluents, the uranium mill operator must sample and analyze liquid effluents for micro-micro quantities of radionuclides such as, radium-226, thorium-230 and lead-210. Special disposal methods or decontamination procedures are required to meet the stringent limitations established by the U. S. Atomic Energy Commission on the concentration of radionuclides in liquid effluents. Routine monitoring of the receiving stream is also normally required. In recent years there has been a growing concern about the radioactivity remaining in the uranium mill tailings, particularly at the sites of shut-down or dismantled mills. The State of Colorado, in cooperation with the industry, has adopted regulations for stabilization of inactive uranium mill tailings. The Mining and Metals Division of Union Carbide operates mills for the recovery of uranium and vanadium at Uravan and Rifle in Colorado and a mill in the Gas Hills of Wyoming for uranium production. The company also owns former mill sites on which mill tailings are located at Maybell, Rifle, and Slick Rock in Colorado and at Green River, Utah. The purpose of this paper is to describe the methods used by a few uranium mills, largely those operated by Union Carbide Corporation, to dispose of radioactive wastes, to discuss briefly the regulations under which the mills operate, and to present reference information on the subject.

Jan 1, 1968

By Kenneth J. Miller

A novel two-stage froth flotation process to remove pyritic sulfur from fine- size coal is described. The process consists of a first-stage, standard coal flotation step in which high-ash refuse and some of the pyrite are removed as tailings. The first-stage clean coal froth concentrate is then repulped in fresh water, and a coal depressant, a pyrite collector, and a frother are added to float the remaining pyritic material. Laboratory and pilot plant flotation results with coals from the Lower Freeport and Pittsburgh beds are given. The pilot plant test results show that up to 80 percent pyritic sulfur reduction was achieved with the Lower Freeport bed coal and up to 50 percent with the Pittsburgh bed coal. Laboratory and pilot plant results were in excellent agreement, indicating that the process is a viable means of removing much of the sulfur from some coals.

Jan 1, 1974

By T. M. Hanna

The results of using a simple analytical solution and a relatively complex numerical model to estimate ground-water inflow to an open pit mine are compared. The analytical solution assumes lateral, radial flow to a fully penetrating pit in an idealized confined aquifer, whereas the numerical model simulates fully three-dimensional flow to a partially penetrating pit from a water table aquifer. The latter is obviously a more realistic simulation of the problem, but the former method is significantly easier to use, Comparison of the results obtained with the two methods for some typical hydrogeologic conditions encountered in mining yields ratios between them in the range of 0.15 to 0.60. These values can be used as a coefficient in the Pit Flow analytical solution to produce reasonable estimates of in-flow even when there are significant differences from the idealized conditions implicit in its application.

Jan 1, 1992

By R. Jin

Fine coal flotation using gaseous carbon dioxide has demonstrated the potential for producing superclean coal. The success of this new flotation .procedure is attributed to the coal's high adsorption potential for CO2. To understand the nature of gas-phase CO2 adsorption at the coal surface, in-situ FTIR spectroscopy in a controlled-environment chamber with an ultravacuum sys-tem has been used and the results are discussed in view of other experimental results from differential scanning calorimetry. It has been found that specifically adsorbed CO2 molecules at the coal surface are polarized and have a characteristic doublet at 2336 and 2361 cm-1. Two adsorption states have been proposed to account for the doublet observed from in-situ FTIR spectroscopy measurements. It is believed that the band at 2336 cm-1 originates from the activated site adsorption of CO2 and that the band at 2361 cm-1 arises due to the molecular aggregation of CO2 within the coal pores.

Jan 1, 1988

By G. Heiken

On the Earth's Moon, obvious hazards to humans and machines are created by extreme temperature fluctuations, low gravity, and the virtual absence of any atmosphere. The most important other environmental factor is ionizing radiation. Less obvious environmental hazards that must be considered before establishing a manned presence on the lunar surface are the hazards from micrometeoroid bombardment, the nuisance of electro-statically-charged lunar dust, and an alien visual environment without familiar clues. Before man can establish lunar bases and lunar mining operations, and continue the exploration of that planet, we must develop a means of mitigating these hazards.

Jan 1, 1991

By Fredrick C. Kruger

We can confidently predict such obvious long-term trends affecting the minerals industry as - increasing consumption, exhaustion of easily discovered near-surface ores, and sharp limitations upon open pit mining by environmental considerations. There- fore, we must intensify the exploration for, and the development and exploitation of, deep bodies of potash and other ores. This paper examines the state of the art of the search for, and the evaluation of, potash from both a geological bias and a mining practicability. The use of indirect geological methods and geophysical techniques, followed by expensive deep drilling, are the conventional approach to evaluation and development of mining plans. The geologist and the geophysicist will have to find ways to perform both of these tasks better and cheaper.

Jan 1, 1973

By R. C. Bunge

Many minerals float best with fatty acids in the intermediate pH range. For example, fluorite, a semi soluble salt mineral, exhibits a maximum contact angle and a maximum flotation recovery in the pH range of 6-8 after conditioning in a palmitate solution (fig. 1). The maximum in flotation coincides roughly, as many researchers have observed, with the boundary of bulk precipitation of the fatty acid. According to fig. Z this boundary is in the above case of 5xl0-7 M palmitate approximately at pH 6.3. For assessing the phenomena occurring at the bulk precipitation boundary of fatty acids, the surface tensions of carboxylate solutions have been measured under various conditions. Fig. 3 shows the surface tension development of palmitate and myristate solutions of increasing concentration at pH 12. Also shown are the bulk precipitation edges (BPE) of the respective solid species that is stable under these conditions, that is the potassium acid soap, HKAZ. Both curves display a similar behavior. As the concentration of carboxylat,e increases, the surface tension decreases, until a minimum is reached at which the curves level off. The decrease of surface tension with increasing carboxylate concentration is generally taken to indicate the surface excess of the carboxylate ion. The point where the curve suddenly levels off has not yet been explained. While it is well known that the onset of micellization (CMC) may cause such an inflexion of the surface tension curve, this cannot be the case here because the position of this point depends, as shown in fig. 4 for palmitate, on pH (the CMC is generally independent of pH). We believe that this point indicates the precipitation of a colloidal acid soap (colloidal precipitation edge, CPE) before the bulk precipitation of this species sets in (BPE).

Jan 1, 1994

By J. P. A. Hortley

In conventional electrolytic copper production, looped copper starter sheets, on which the copper is deposited, are supported by hard-drawn copper bars. These bars have cross-sectional areas of between 1 and 1.4 in2. The suspension bars serve two purposes: firstly to support the cathode, which can weigh up to 150 kg, and secondly to introduce the electric current. IYI examined these two requirements in detail to see whether a better design could be achieved. Considering firstly the current carrying requirement, it wee noted that under normal refinery conditions, each cathode carries between 400 and soak. If one applies the generally accepted rule that 1 in of copper can carry 1000A4 a suspension bar need theoretically contain only 1/2 in2 of copper. This contention is supported by the fact that the 500A current passed through the cathode also appears to pass quite satisfactorily through the two support loops, which have a cross-sectional area of approximately 0.35 in 2. Turning now to the strength requirements, the cross-section of hard-drawn copper bar required to support a 150 kg cathode is relatively small, and easily met by the present designs. It is not, however, the static load applied by the 150 kg cathode immersed in the electrolyte which causes the damage to the hard-drawn copper, or even the increased static load of a 100 kg man standing on one foot in the centre of the bar; the damage is actually caused by the dynamic loads applied to the bare when they are dropped, thrown into containers, lowered too rapidly into the cell, or otherwise mistreated. The important requirement is therefore that the bar does not permanently bend. Its proof stress of limit of proportionality, rather than the amount that it deflects under static loading, should be the strength criterion. With the hard-drawn copper normally used for the manufacture of suspension bars, it has been observed that the copper becomes annealed during use, particularly at the end of the bar where the current is introduced. Thus, after a relatively short time, the cathodes are in effect being supported by annealed copper bars.

Jan 1, 1978

By Jack Barrett

The oxidants which participate in the bacterially catalyzed oxidation of minerals are dissolved oxygen and some aqueous iron(III) complexes. Speciation studies indicate that these complexes consist of iron (III) -sulfate and iron (III) -arsenate ions. The complexes have different oxidizing powers as indicated by their calculated standard reduction potentials. The thermodynamics of the oxidations of pyrite and arsenopyrite are related to the mechanisms of the reactions. The mechanisms are discussed in terms of primary processes occurring on the mineral surfaces and the secondary reactions of the primary products. The importance of the conclusions to plant operation is discussed.

Jan 1, 1993

By John A. Organiscak

The Bureau of Mines evaluated a new dust control technique for longwall personnel required to work at the tailgate end of the face. This technique utilizes a water-powered scrubber to clean a portion of the face air, which is discharged behind a brattice partition at the working area. Laboratory simulation of this system in a wind tunnel resulted in average efficiencies greater than 70 pct with system efficiency directly related to scrubber quantity. Underground evaluations indicated a similar direct relationship between scrubber quantity and system efficiency. Gravimetric measurements of respirable dust made during these underground evaluations resulted in average protection efficiencies ranging from 30.7 to 42.5 pct with increasing scrubber air quantity.

Jan 1, 1983