Search Documents

By D. Tao, B. K. Parekh

Fine coal particles are difficult to separate effectively from liquids or other solids. Ultrasonic energy may be used to enhance the efficiency of the conventional fine-particle separation processes widely used in the coal and mineral industries. Flotation, settling and dewatering tests were conducted using several fine coal samples to study the effects of ultrasonic treatment on these processes. Process variables such as particle size, ultrasonic treatment time and solids concentration were investigated for their impacts on ultrasonic treatment effectiveness. The results obtained from this study showed that ultrasonic treatment is an effective approach for enhancing solid/solid separation in flotation and solid/liquid separation in sedimentation and dewatering of fine coal. SEM microphotographs demonstrate that ultrasonics cleaned particle surfaces, which is, in part, responsible for the observed improvement in fine coal separation processes.

Jan 1, 2000

By O. Olajide, E. H. Cho

A laboratory study of the jigging process with Pittsburgh seam coal has been conducted. The laboratory-scale Baum jig used in this study was a McNally-Norton LO30X Right Hand Model Baum jig with an effective screen area of 0.186 m2 Feed material was prepared by selecting a size range from 6 mesh to 1.91 cm. Solid feed rates were 27.2 kg/min and 32.7 kg/min. Water flow rates were varied from 37.9 to 94.6 L/min. It has been found that smaller particles give higher values of density of separation and lower efficiency of separation. Increasing water flow rate increases the discharge rate of clean coal at a constant solid feed rate. It appears that the efficiency of separation increases by increasing water flow rate up to a certain value, and then levels off upon increasing the flow rate further.

Jan 1, 1988

By Travis S. Wellman, Jon C. Volkwein

The Bureau of Mines conducted a study to assess the impact of a directional water spray system on a unique single inlet dust scrubber on a low profile mining machine. Tests were conducted in a full scale model mine using a Joy 12 CM 10-AA continuous mining machine. Tracer gas was introduced at the face and concentrations of the tracer gas were monitored at the face and in the return. Various parameters included: mining position, depth of cut, brattice setback and combinations of scrubber, directional sprays or symmetrical sprays. Results indicated that either directional or symmetrical water spray configuration improved the ventilation effectiveness of the scrubber by a factor of 2 to 3. Average face ventilation effectiveness (FVE) values for all testing of the scrubber and directional sprays were 0.95, versus 0.37 for a standard 6 m (20-ft) blowing curtain without sprays. No FVE values were less than the standard 6 m (20-ft) blowing results.

Jan 1, 1989

By D. W. Fuerstenau, J. Vazquez-Favela

This paper shows how the efficiencies of size-reduction processes depend on the mode of particle constraint and energy transfer within the comminution device: namely, whether the process consists of single-particle loading, confined-particle-bed comminution or loose- (unconstrained-) particle grinding. The relative efficiency of single-particle comminution, ball-mill grinding and particle-bed comminution in the recently invented high-pressure roll mill is evaluated by making use of the self-preserving nature of the size distributions of comminuted products. The highest energy efficiency can be achieved by utilizing a hybrid two-stage system in which the material is first ground in the high-pressure roll mill and then the ball mill.

Jan 1, 1998

By M. Stefanakis, A. Kontopoulpus, K. Adam

The application of Bacterial Oxidation as a pretreatment step for the extraction of gold from the Olympias refractory pyrite concentrate is described. A wide review of Bio-oxidation is presented focusing on the current process developments and commercial applications relevant to the treatment of gold bearing sulphide ores and concentrates. Preliminary batch and semi- continuous tests on the Olympas concentrate indicated that with Bacterial Oxidation quantitative gold liberation may be achieved. fie effect of such parameters as pH, Eh, temperature, particle size, operating pulp density and retention time on the extent of sulphur oxidation and subsequent gold extraction by conventional cyanidation are also examined. Finally, a preliminary evaluation of Bacterial Oxidation as a potential process alternative for the treatment of the Olympias concentrate is presented.

Jan 1, 1989

[Costs may be classified according to their source and behavior: Scale of aggregation - Total costs - Unit costs Time period for which the costs are charged - Product costs - Period costs Controllability and relevance for decision-making and control - Controllable costs - Noncontrollable costs - Sunkcosts - Opportunity costs Their basic source - Production costs (also termed manufacturing costs) - Nonproduction costs How the costs change with changes in activity - Fixed costs - Variable costs - Semivariable costs Traceability to individual units of production - Direct costs - Indirect costs Use in planning (budgeting) and subsequent control - Standard costs - Normal costs ]

Jan 1, 1999

By P. Bevilacqua, G. Ferrara

The paper discusses the problem of accuracy in the determination of the partition curve of gravity separation processes, which is strongly affected by both the sharpness of separation of the density analysis system used and the width of the density range selected. The problem is important when the density analysis of the separation products cannot be performed using heavy liquids, but has to be performed using heavy suspensions or using other systems such magnetogravimetric separation. The imperfect separation given by these systems and the use of large density ranges lead to the determination of apparent partition curves instead of actual partition curves for the process. In the paper the relation between apparent and actual partition curves is studied under different conditions through a simulation program. For different input data, special diagrams are given which, once the apparent partition curves and the sharpness of the density cuts are known, allow calculation of the actual partition curves and the related parameters.

Jan 1, 1995

By Y. Ye, J. D. Miller

Certain bituminous coals are known to contain appreciable quantities of natural fossil or subfossil resin. Such resinous coals are found in the western US, particularly the Wasatch Plateau coalfield of UT. Some of the seams in this field contain an average of 5% resin. This fossil resin has been recovered by gravity and/or flotation processes since 1929. Resin concentrates thus produced are of low quality and are usually refined by solvent extraction. The purified resins are of commercial importance in the adhesive, coating, rubber. and ink industries, etc. An improved flotation technique has been developed which involves ozone conditioning to selectively float resin from high-volatile bituminous coal. With this flotation process, a concentrate product which contains 95%

Jan 1, 1990

By S. E. Phillipson, P. L. Tyrna

Lineament analysis, a remote sensing application, for geological structures, has been criticized, for its reliance on subjective interpretations. The Mine Safety & Health Administration's Roof Control Division performs lineament analyses with a technique that removes much subjectivity. Study areas are viewed on satellite images with software that allows examination under artificial sun azimuths and elevations. Extraneous lineaments are removed through successive steps of superposition, resulting in selection of the most robust linear features. Field investigations revealed a strong coincidence of joint and. fault zones that were parallel with projected lineaments. The Roof Control Division's successful identification o f lineaments associated with roof falls and high wall failures has prompted some mine managers to incorporate lineament analysis as a mine-planning tool. The identification of potentially hazardous ground conditions would allow mine operators to obviate safety concerns that might otherwise adversely affect the health and safety of miners.

Jan 1, 2003

By Kenneth N. Han, Peter Mam-soo Kim

The extraction behavior of gold in ammoniacal solutions in the presence of bromine as an oxidant has been studied. The effect of concentration of ammonia, bromine, and pH of the solution on the rate of dissolution of gold was investigated. The dissolution behavior has been analyzed using electrochemical method, and its results were compared with direct leaching tests using gold powder. The overall dissolution of gold in ammoniacal solution containing bromine was found be affected significantly by pH of the solution and the concentration of bromine. The rate expression found in this study has the following form.

Jan 1, 2005

By J. P. Golightly

The nickeliferous laterites of Soroako are described in their setting in the huge Cretaceous ultramafic complexes of central Sulawesi, Indonesia. The ore bodies occur on spurs, ridges and hill flanks beneath remnants of extensive erosional surfaces. Weathering pro- files that have developed on unserpentinized harzburgite and on strongly serpentinized lherzolites show distinctive laterite structures, mineralogy and chemistry. The former are unique to the Soroako area and permit an unusual degree of upgrading by rejection of unserpentinized peridotite boulders. A mass balance calculated for a selection of profiles indicates that in situ leaching of a column of peridotite 20-50 meters thick has taken place with only minor lateral migration of nickel in solution.

Jan 1, 1979

By Richard R. Klimpel

This article introduces the basic definitions and philosophy behind process hazard evaluation procedures and the determination of risk as being a function of accident probabi1ity and accident consequence. The general concepts of good engineering practice and predictive hazard evaluation are discussed. The most commonly employed methods used in the processing industries are reviewed with an eye towards briefly presenting what each method offers as far as information, time and resources required, etc. Some initial references on the actual practical use of each technique in the processing industries are also given.

Jan 1, 1991

By J. E. House

Creative ideas and endeavors require imaginative and positive responses, if they are to be reduced to practices. This lecture will define the plurastic roles of various technical disciplines which were important in the development of the LIX reagents. Specific personalities, facts, and events will be used to trace the development from an idea, to the exciting acceptance and practice of the technology. An objective analysis of the entire LIX reagent development, spanning twenty-five years experience of the author, will be given, these will be used as a basis for critical examination of how the various technical disciplines could improve their effectiveness in advancing future technologies.

Jan 1, 1990

By J. J. Moore, I. Iwasaki, L. A. Lindeke

Correlation of scale-up from small-scale batch laboratory mills to large-diameter industrial mills was established by performing two series of laboratory and pilot plant grinding tests using a magnetic taconite ore and a siliceous sulfide ore. In one series, controlled batch grinding tests in 203-, 508-, and 914-mm (8-, 20-, and 36-in.) diameter mills were carried out followed by a second series involving continuous grinding tests using 305-mm (12-in.) and then 1067-mm (42-in.) diameter pilot plant ball mills in open circuits. The effects of ball diameter on wear and of mill diameter on grinding power and ball wear are illustrated.

Jan 1, 1988

By W. S. Fyfe

Gold is mobilized or made soluble under all crustal conditions given appropriate fluid chemistry with molecules which complex gold. In the surface environment chloride, thiosulphate and a host of organics may mobilize gold. In the epithermal range bisulphide appears effective as shown by the classic studies in the Taupo volcanic zone of New Zealand. In the high grade metamorphic to igneous ranges little is know but it appears that gas molecules in the system CO2 -CO-H20-S-C1 can do the job. Precipitation may occur by changes in P-T-EL-pH or boiling where such changes influence the liquid concentration. Of the known regimes information is good for epithermal systems, poor for surface lateritic environments, inadequate for high-T systems. Gold is often concentrated in bio-systems both living and dead. The influence of biosystems is little appreciated. There is a great potential for the discovery of new types of gold deposits and in particular, gold in weathering environments, gold in very high-T environments, gold in strike-slip faults and thrust regimes, and gold as a by-product in materials like coal and other organic debris. By the year 2500 we may find our noble metal resources in the asteroids.

Jan 1, 1987

By Gordon I. McPhail, John D. Nelson

Tailings management represents a major portion of the cost associated with extraction of gold. For each gram of gold extracted, 150 to 200 kg of waste material is produced. Because of environmental concerns and unwillingness of society to accept environmental damage caused by poor waste management practices it has become essential to follow responsible and safe practices in tailings management. This paper presents general aspects of tailings management and discusses different techniques utilized. Characteristics of tailings and the effects that these have on stability and environmental aspects are discussed. The paper also discusses the effect of mine back-filling practices on the surface disposal of the remaining tailings fraction.

Jan 1, 1987

By John Jonkman

Many companies in the mining and minerals processing industry are finding themselves in the transition stage from the Industrial Age to the Information Age and are trying to become prepared for the Knowledge Age. To remain competitive in the decades ahead, they are faced with integrating the enterprise through the use of computers and networks. This paper discusses some common human and organizational barriers to enter- prise integration. It proposes how to develop the organizational and human' networks to match the capabilities of the technical networks which are being' implemented. Ten practical considerations are then presented for consideration in the executive suite in addressing the human side of implementing the computer integrated enterprise.

Jan 1, 1989

By Sundar S. Saluja

Efficient and re1iable methods of fragmentation through blasting have been sought ever since the introduction of black powder in mining operations, but the pace of investigation became faster with the discovery of nitroglycerine. The development of modern measuring instruments and the need to blast more rock with the least damage has made the study of blasting mechanics and its application more important, particularly since the oil embargo. Investigations into the practical approach evolved by Daws (1909) and the work done to make it more useful is discussed. The work of several investigators is touched upon with particular reference to the development of computer programs to simulate and optimize blasting operations.

Jan 1, 1986

By T. S. Golosinski

This article reviews current contract mining practices in Australia. Various types of contracts are reviewed, including partnering arrangements and alliances between the contractor and the mine owner. Applicability is also discussed of various types of contracts to specific mining situations, as is their effect on overall mine performance.

Jan 1, 1998

By Andrew T. MacKenzie, Paul A. Rantala

Predictive pastefill rheology (flow characteristic), models have long challenged pastefill practitioners. While the methodology and practicality of recipe formulation is attainable in most locals, the remaining challenge has been to devise a predictive mathematical or empirical model of paste flow characteristics. Flow phenomenon can now be assigned mathematical and physical basis. The authors herein disclose physical and mathematical methods that demonstrate how operators could proceed when designing reliable pastefill systems. Knowledge presented will allow users flexibility in adjusting flow-rates. Laboratory data shows stiff pastefill delivery design can be derived through mathematical relationships of particle size, material characteristics and pipe diameter.

Jan 1, 2001