Search Documents

By H. H. Richards, Ray L. Tobie, L. A. Thomas

GENERAL DESCRIPTION Since the beginning of operations, with the exception of a small tonnage mined by slushing, ore extraction has been by full gravity caving. Formerly, a checkerboard sequence of block undercutting was followed with the even-numbered blocks in one panel and the odd¬numbered blocks in the adjacent panel being mined. As these blocks were depleted, the intermediate or pillar blocks were mined (Fig. 1). Following this checker¬board, the mining sequence went through a number of changes, finally evolving into diagonal retreat panel cav¬ing by blocks (Fig. 2). The numbers in Fig. 2 indicate the sequence in which blocks were undercut. Gaps in the numbering sequence indicate undercutting on the level outside the illustrated area. Geology The ore body is a low-grade deposit of chalcopyrite mineralization disseminated throughout structurally weak, highly fractured, strongly altered granitic host rocks. It takes the shape of a gently dipping elliptical cylinder consisting of an ore shell of variable thickness surrounding an interior waste core. Major and minor axes of the mineralized cylinder are 1524 m (5000 ft) and 762 m (2500 ft), respectively, and length approximates 2438 m (8000 ft). Ore is sufficiently fractured to break readily into medium-coarse size. The igneous rock complex containing the ore body is covered by a wedge-shaped blanket of Tertiary con¬glomerate which was brought into place by faulting along the major regional structure of the San Manuel fault. Thickness of the conglomerate cap varies from only 9 m (30 ft) at the east end of the ore body to more than 610 m (2000 ft) at the west. Structurally, the con¬glomerate is much more competent than the igneous host rocks and, when caving, it breaks into massive chunks. Conglomerate boulders seen in drawpoints underground are very coarse. The total rock column over the initial mining area of the 1415 grizzly level was 354 m (1160 ft) of which 122 m (400 ft) was ore, 79 m (260 ft) was leached igneous capping, and 152 m (500 ft) was conglomerate above the San Manuel fault. Diamond Drilling: From 4572 to 7620 m (15,000 to 25,000 ft) are drilled annually from underground workings to delineate the ore body. MINE DEVELOPMENT Haulage Level In the south or main ore body (see Figs. 3-6), with the exception of the draw and transfer raises, all the extraction openings are concreted (Seaney and Tobie, 1965). The haulage panel drifts, which are 18 m (60 ft) below the grizzly drifts, are first driven with pre¬concrete ground support. The drift, which has an arched section, then is concreted using mobile collapsible steel tunnel forms. The haulage drifts leading from the pan¬els to the hoisting shafts are not concreted. After the panel drifts have been concreted, the raise stations from which transfer raises will be driven are constructed and the raise-station ore-drawing chute is installed. The chute is prefabricated of A-36 steel with undercut guillo¬tine gates made of abrasion-resistant 2.5-cm (1-in.) steel plate powered by 20-cm (8-in.) air cylinder installed on each side of the raise station. Transfer Raises The transfer raises are lined with 15 x 20-cm (6 x 8-in.) cribbing and are 1.22 m (4 ft) in the clear. Each cribbing is protected from wear by a high carbon steel angle which is nailed onto the cribbing. The transfer raises are driven from each side of the raise station on an angle of 1.1 rad (63°). Each raise con¬sists of a main and a backover branch. The transfer¬raise driving crew consists of two men working one shift only. Grizzly Drifts After the transfer raise reaches the grizzly level, the grizzly drift can be driven. The grizzly drifts are spaced at 10.6-m (35-ft) centers and are driven parallel to the long axis of the ore body (see Fig. 2). This drift is driven by a two-man crew working on one or more drifts at a time using feed-leg machines. The eight grizzlies in the 42.7-m (140-ft) long drift are spaced at 5.3-m

Jan 1, 1982

By Marco D. Boscardin

During subsidence, the ground surface may settle, change slope, change curvature, go into tension, and/or go into compression. In response to these ground movements, buildings and buried utilities in the subsidence area may settle, tilt, bend, distort, and sustain extension, compression and/or torsion. In order to develop measures to protect existing structures and utilities, or to design new structures and utilities to withstand potential movements in areas of subsidence, it is necessary to understand the interaction between the ground and the building or buried the utility. This paper reviews subsidence-induced ground movements, how these ground movements are transmitted to and accommodated by buildings and buried pipelines, and how these structures may alter ground movements relative to free field subsidence-induced ground movements.

Jan 1, 1986

By A. T. Iannacchione

Recent fatal injuries occurring during pillar retreat coal mining call for better identification of the hazards and recognition of risks. Ground control hazards associated with room-and-pillar retreat mining tend to intensify with depth, requiring extra precautions in the form of additional controls. In many locations these activities are further complicated by local complexities often associated with unique or novel circumstances, such as over-mining or under-mining. One technique recently studied by NIOSH, Major Hazard Risk Assessment (MHRA), may help mine operators to mitigate the risks associated with pillar recovery operations. The approach was trialed at two underground coal mines in southern West Virginia that are currently practicing pillar recovery. The first step in the MHRA process involved reviewing the segments or parts of the pillar extraction mining system and identifying associated hazards and threats to the operation. Some of the high risk hazards at these two sites included: ? Rock fall during pillar extraction covers equipment and injury occurs during recovery operations, ? Rock fall above the roof bolt horizon, potentially injuring ? workers and/or requiring recovery action, ? Rib fall under deep cover, potentially injuring workers, and; ? Strata instabilities associated with subsidence of the interburden due to simultaneously mining two seams in close vertical proximity to one another. The mines? risk assessment teams then considered each threat individually in order to systematically identify potential unwanted events. The top unwanted events were examined individually using structured risk analysis tools. The output from the process includes a list of priority existing controls for monitoring and auditing, and a second list of potential new controls. These controls consisted of: Examples of best practices, ? Enhanced communication, ? Implementing standard operating procedures (SOP), ? Protocols for emergency response actions, ? Effective layouts, ? Efficient monitoring, and; ? Successful audits. This paper documents the process as it unfolded at the two mines, and analyzes the strengths and weaknesses of the MHRA technique as it applies to pillar recovery operations. This work was part of a larger NIOSH research project. NIOSH was responsible for: 1) facilitating the risk assessment process known as Major Hazard Risk Assessment (MHRA), 2) documenting the risk assessment process, and 3) providing mine management with a written draft summary of the risk assessment process. The results of the risk assessment represent the thoughts and opinions of the individual risk assessment teams and should in no way be construed as an endorsement of the risk assessment output by NIOSH or the University of Pittsburgh.

Jan 1, 2009

By Eberhard Werner

Existing reports on the effects of mine subsidence on water wells and springs appear to be inconsistent. Some report quick and complete recoveries to pre-mining conditions while others indicate long-term or permanent effects. It is clear that topographic and geological factors as well as precise position with regard to the mine are important in determining probable effects of subsidence on aquifers. Ridgetop aquifers which are well above regional base-level are much more susceptible to disturbance by mining activities than those located topographically lower. Effects seen are attributed largely to increased permeability, both horizontal and vertical. of the aquifer rocks. The deeper aquifers usually show short term losses or water-table declines. but the effects on the ridge-top aquifers persist for longer periods or may be permanent. Subsidence enhances permeability. so that infiltrating water moves much faster to lower levels. causing pond and stream losses and declining levels in wells as well as declining flows of springs of the higher aquifers, while increasing levels and flows of the lower aquifers. Additional effects are shifts of spring locations caused by minor tilts due to differential subsidence and redirection of shallow flows by changes of horizontal fracture permeability. These effects are seen as mining of a panel progresses beneath the site. and are often repeated when adjacent panel mining fronts pass the site. Analysis of water well level and spring flow records indicates that the effects are greatest at the edges of longwall panels in the tensional regime. These effects are amplified for locations close to topographically steep terrain and in close proximity to fracture traces mapped from medium-to small-scale aerial images.

Jan 1, 1986

By G. J. Simandl

Jade is a commercial term encompassing green, white, black or yellow-brown jadeitite and nephrite. Jadeitite consists of Na-rich pyroxene, whereas nephrite consists of prismatic to acicular amphiboles of the tremolite-actinolite series forming bundles that are randomly oriented and interlocked. Nephrite is tougher (harder to break) than jadeitite. Its fracture strength is about 200 MN/m2 whereas that of jadeitite is about 100 MN/m2. On the other hand, jadeitite has a higher hardness (7 compared to 6.5 on the Mohs scale). There are over fifty known nephrite occurrences in British Columbia (B.C.). These occurrences consist of individual blocks, boulder fields, talus blocks and in situ occurrences. Most of the in situ occurrences are lens or cigar shaped. They occur at, or near the contact of ultramafic/mafic rocks (mainly serpentinites) with cherts, and other metasedimentary or igneous felsic rocks of Mississippian to Jurassic oceanic terranes such as Cache Creek and Slide Mountain. These contacts are commonly interpreted as shear/fault related. In general, it is believed that the B.C. nephrite formed by metasomatic exchange between ultramafic and silica-bearing rocks. Impurities in B.C. nephrite are spinel group minerals (chromite, magnetite, picolite), diopside, uvarovite, titanite, chlorite, and talc. Jadeitite is slightly denser than nephrite and good quality material sinks in methyl iodine. There are no known jadeitite occurrences of economic interest in B.C., but there are at least four geographic areas where favorable lithologies, and metamorphic conditions (Pn) required for the formation of jadeitite coincide. These are Bridge River, Pinchi Lake, Dease Lake, and Jennings River. These areas are known to contain small concentrations of jadeite, or are characterized by blueschist or eclogite-grade metamorphic conditions. Rhodonite and pyroxmangite are MnSi03 polymorphs. These minerals are pyroxenoids and are macroscopically and microscopically very similar. For brevity, both are grouped together under the term "rhodonite". Most of the B.C. occurrences are hosted by late Paleozoic chert sequences and are lens shaped and concordant. The common association of rhodonite with iron formations, jasperoids, and/or volcanogenic sulphide deposits in southwestern B.C. permits the delineation of favorable horizons using magnetic or electro-magnetic geophysical methods. Geographic associations between manganese showings and sulphide deposits, and the hydrothermal chemical signature of the rhodonite occurrences from this area, suggest a genetic link between rhodonite and volcanogenic sulphide deposits. The typical rhodonite rocks consist of rhodonite, pyroxmangite, neotocite, black amorphous Mn-oxides, Mn-bearing garnet, ± epidote, ±chlorite, ±rhodochrosite, ± parakutnah-orite, ± Mn-bearing calcite, ± iron oxides and hydroxides. Garnet ± epidote forms yellow patches and layers within the rhodonite. Within some of the rhodonite occurrences, the garnet is altered to chlorite. Rhodonite-bearing rock is commonly cross cut by secondary manganese oxide veins, creating a characteristic web-like texture. In several localities, the contorted bedding planes are readily recognized. Mn-calcite and quartz also crosscut rhodonite. Rhodonite deposits hosted by high grade metamorphic rocks may contain pyroxmangite. Rhodonite is an important gemstone and ornamental stone in B.C., second only to nephrite in dollar value. B.C. nephrite and rhodonite have been used for the past 100 years in local jewelry and ornamental applications. More recently they have been used in table tops, and they have potential as upscale materials in tile-making. There may be a market for tiles made from lower grade materials that were previously extracted and stockpiled. The prices of nephrite, jadeitite, and rhodonite vary widely with quality, but gem and ornamental grade stones are relatively highly priced materials and they trade world-wide.

Jan 1, 2001

By Eric W. Johnson

In the late 1950's a low-grade copper ore zone was outlined at the fifty-year-old McIntyre Porcupine Mine in Northern Ontario. Following this an independent copper circuit was installed in the existing gold mill. The nature of the operation decreed that capital expenditure be a minimum. To this end, in order to resolve the problem of storing and grinding two separate ores, it was decided to install a divider in the existing 4000 ton capacity fine ore storage bin and to replace ten conventional feeders with sixteen Mexican feeders. The article describes a successful application of the Mexican type feeder.

Jan 1, 1968

By Egon Pohl, Friedrich Steinhäusler, Werner Hofmann

INTRODUCTION Anticipated increase of nuclear fuel production in the future coincides with growing concern about the occupational health risk of miners from inhaled radon decay products. As a consequence it has been suggested to even lower presently permitted exposure levels (NIOSH, 1980) and implement more stringent control on measurement programmes. Compliance with these regulations requires large investments in new or modified ventilation systems as well as in increased expenditure for staff and instrumentation for health physics operational monitoring. Since both costs are directly related to the overall ore production costs, this can have far reaching implications with regards to the economic feasibility of certain mining operations and consequently reduce estimates of low-cost minable ore reserves. In addition there is increasing evidence that the radon problem is not limited to the nuclear fuel cycle only, but can also represent a significant hazard to non-uranium miners. A key component in the cost-effective implementation of legislative control measures is the monitoring system employed. The choice of system is decisive for the total costs of installation and maintenance, manpower requirements and accuracy of nuclide determination. In the following operational specifications are defined for monitors in mining and milling environments. Different types of available instrumentation are discussed with regard to their suitability for practical radiation protection in underground mines, open cut mines and mills. ATMOSPHERIC CHARACTERISTICS Underground mines Radon in the air of underground mining operations is exhaled from surrounding rock surfaces, crushed material and, to a lesser extent, from water seepage. Whilst in uranium mines radon releasing ore bodies are generally localized in distinct areas, radon sources in non-uranium mines can be very dispersed throughout the system of mine tunnels. The ventilation scheme used influences the absolute atmospheric level of radon as well as the equilibrium conditions between radon and its decay products (factor F). In uranium mines mechanical forced-air ventilation is normally the only way to achieve and maintain legally required nuclide levels. This causes the F-factor to be rather low, e.g. in French CFA-mines F is of the order of 0.2 (Francois, Pradel, Zettwoog, 1975). At the same time the fraction of unattached radon decay products (fp) can increase due to the high air velocities employed. However, it is possible to find non-uranium mines with either natural draught ventilation only or assisted on demand by forced air ventilation during special operations or climatic conditions. Thereby the F-factor is more dependent on seasonal changes of temperature differences between outdoors and mine atmosphere and work routines. As a result F can cover a wide range from 0.02 to 0.95 (Steinhäusler, 1976). The use of filters or electro-precipitators in mine ventilation systems can modify the atmospheric characteristics twofold as it generally decreases the content of radon decay products, but at the same time increases the content of the unattached fraction fp . Average concentration levels of radon decay products are mostly lower in mechanically ventilated non-uranium mines than in equally ventilated uranium mines and are below 0.3 Working Level (UNSCEAR, 1977). However, some working places in non-uranium mines, specially with only natural draught ventilation can occassionally approach maximum permissible levels as defined for uranium mines (Strong, Laidlaw, O&apos;Riordan, 1975; Snihs, 1976; Sciocchetti, Scacco, Clemente, 1981). Open pit- and surface mines Radionuclide levels of radon decay products in the atmosphere of these mines are mostly too low to represent a significant inhalation hazard for miners, ranging typically from 0.03 to 0.1 Working Level (Steinhäusler, 1976). However, personnel using airpurifying respirators or working in cabins ventilated with filtered air can be exposed to a radon atmosphere with low value for the F-factor (F [<] 0.1) and high fp-value up to 80 % (Leach and Lokan, 1979). Mills Atmospheric radon concentration in crushing, grinding, drying and packing sections depends on the radium 226 content of the ore, ore storage methods and ventilation system employed. Providing adequate ventilation ([>] 2 air changes per hour) and control of dust production radon and its decay products represent only a minor problem (Saconney, 1979). MONITORING OF OCCUPATIONAL EXPOSURE Objectives Operational monitoring of the working places provides information on: - confirmation of appropriate control of the routine mining methods employed - indication of abnormal conditions. Although this type of monitoring enables the location

Jan 1, 1981

By Louis J. Trostel

Refractories, called the Hidden Industry by The Refractories Institute, provide the temperature and chemically resistant linings for the multitude of vessels that are used today in high temperature processes ranging from giant iron-making blast furnaces to industrial incinerators to petrochemical cracking units to the smallest furnaces used by the jewelry trade. While these refractory linings are absolutely essential to the proper functioning of these processes, the linings are almost always on the inside of the vessels and thus hidden from the eyes of the public. Refractories are defined in Standard C71 of the American Society for Testing and Materials (ASTM), titled "Standard Definitions of Terms Relating to Refractories," as "nonmetallic materials having those chemical and physical properties that make them applicable for structures, or as components of systems, that are exposed to environments above 1 000°F (538°C)." This criterion of ability to withstand exposure to environments above 538OC is the critical distinction separating refractories from other ceramics, fibers, and coatings applicable only at lower temperatures. In addition to resisting temperature, the refractories must with- stand abrasion, chemical and slag attack, resist thermal shock, and carry sustained structural stresses at high operating temperatures for as long as years. The most common methods of classifying refractories are by forming method and composition. First are the traditional formed and fired bricks, batts, and the associated multitude of special shapes. These refractories are usually formed at room temperature, dried, and then fired to high temperatures to develop the final properties desired. Other formed refractories are chemically bonded or resin or tar bonded. To complete the formed refractory matrix, some fired refractory bricks and shapes are subsequently impregnated with resins or tars. Physical dimensions of these formed refractories are classified into two general categories: standard sizes and special shapes. The standard sizes are those in common usage in the United States described in ASTM Standard C909 "Dimensions of a Modular Series of Refractory Brick and Shapes" based on the 38 mm basic module as described in ASTM Standard C861 "Determining Metric Dimensions of Standard Series Refractory Brick and Shapes." The most common size is the "9-inch straight" 228 x 114 x 64 mm (9 x 4 ½ x 2 ½ in.) of the "2 ½ -inch" series or 228 x 114 x 76 mm (9 x 4 ½ x 3 in.) of the "3-inch" series. Bricks of nonstandard sizes are referred to as special shapes. Their use is required in specific furnaces for particular requirements or applications. In addition there is the large and growing group of refractories sold as unshaped mixtures that may be formed into their final shapes at the application site. These unshaped mixtures are sometimes referred to as specialties. The mixtures are prepared to be hydraulically cast, plastic or wet rammed, dry rammed, or dry vibrated into their final shapes. Some are designed to be projected through nozzles (or gunned) onto their forms. The refractory mortars used to lay up the shaped refractories fall into this group referred to as specialties. Prepared refractory grains also are sold. These are usually calcined or fused materials that are subsequently crushed and sized to a variety of specific carefully controlled grain sizes or size distributions. These grains include calcined fire clay, dead burned magnesite, periclase (fused magnesia), dead burned dolomite, kyanite, tabular and fused aluminas, fused zirconia, fused mullite, and calcined alumina-magnesia spinel. The primary composition groups of refractories are the 1) alumino-silicate refractories made largely from fire clay and high- alumina materials, 2) silica refractories made from quartzites and ganisters, and 3) basic refractories from magnesia (or magnesite) and chromia (also referred to as chrome ore), alone and in combination, and dolomite. Special refractories include carbon, zirconia, zircon, high purity alumina, mullite, silicon carbide, silicon nitride, and some borides. In addition there are groups of special insulating refractories.

Jan 1, 1994

By Robert D. Schmidt

The Bureau of Mines is conducting an investigation to develop remediation techniques for residential water wells whose yield has been affected in the long term, by underground mining. Initial work relating to this project was conducted in 1984-1987 at a room and pillar mine in Indiana County, Pennsylvania. Piezometer nest data from the room and pillar mine reveals that a downward gradient in piezometric head exists in shallow strata as a result of drainage into the underlying mine void. The vertical gradient in head in turn results in well bore leakage in open-hole water wells. The relative yield of valley wells is only slightly affected however because the high surficial recharge rate through fractures more than compensates for fracture leakage into the underlying mine. The relative affect of well bore leakage on well yield is greater in certain hillside and hilltop wells that have comparatively low inflow rates at shallow depths. The static water level of such wells is determined to a much greater extent by the chance interception of deep outflow fractures, than is the case for wells drilled in a more intensively fractured valley bottom. The lower static water level of wells that intercept deep fractures does not necessarily reflect the water table conditions outside of a small radius around the affected well. The results suggest that permanently isolating well bore outflow fractures may remediate certain open-hole residential wells that have been affected by high extraction underground mining.

Jan 1, 1986

By N. Piret, B. Shoukry, S. Buntenbach

Traditional or artisanal goldmining, also known as small scale goldmining, has a strong and probably a negative environmental impact. The processing methods applied are very frequently a source of severe pollution due to the emissions of mercury by the extraction of gold by means of amalgamation as well as the emissions of cyanide through cyanide leaching of gold bearing ores. The emissions find their way into the environment and contaminate soils, sediments, water and atmosphere. Abnormal concentrations of mercury and cyanides in waterways are known to occur year after year destroying irreplaceable regions of the world. Mercury and cyanide compounds are highly toxic and may directly create permanent damage to the whole ecosystem. Existing methods for recycling of mercury and for decontamination of mercury and cyanide contaminated tailings are not customary applied in small scale mining and are ineffective as well. Based on investigations of traditional and small size goldmining, this paper presents: -processing methods of gold and discarded tailings under consideration of environmental protection; -figures on actual situation; -recommendations for equipment; -some decontamination methods for mercury and residual cyanide. Mineral Processing methods in traditional gold mining Gold is usually existing in its ores as the metal alloyed with metallic silver and perhaps copper. The element may occur in the form of: -native gold -inclusions also of microns or submicroscopic size metal sulfides (auriferous) such as pyrite, pyrrhotite, stibnite, arsenopyrite and galena -combined as telluride or sulphotelluride. The separation process selected depends on whether the gold can be freed from its unfavorable associations (e.g. gangue) at a sufficiently coarse grain-size, or whether it is carried in a heavy sulfide which can be freed similarly. The usual practice is to concentrate the goldbearing mineral at a relatively coarse grain-size and to regrind the ore if necessary. The gold content is concentrated by secondary or tertiary gravital methods or is extracted by chemical methods (amalgamation, cyanidation etc.) Gold, even when of fine grain-size, settle readily due to its high specific gravity from pulps in which the main gangue mineral is quartz or silicates. Amalgamation is the process of separating gold and silver from their associated minerals by binding (entrapping) them into a mixture with mercury. The cyanide process is applied to separate gold or gold-bearing compounds by dissolution from the finely ground ore (CIP, CIL, RIP), or as heap leaching. The dissolved gold is separated from the solids and the metal-rich or pregnant solution is then treated to recover its gold. Gold is also recovered by flotation methods. This process is widely used in treating base metal ores and in separating various sulfide components of ores, as well as in removing the barren gangue. The gold usually associates with a specific product in a sequence of flotation operations and is recovered subsequently in the smelting of the sulfide concentrates and refining of the metallic products, or by cyanidation of the roasted concentrates. Froth-flotation can be applied to separate gold and sulfide minerals from a finely ground pulp. The Amalgamation Process Amalgamation is the main method for the recovery of gold in traditional mining and is applied for the extraction of gold from placers as well as primary ores. The mineral technology used depends on the nature of ore deposits. In winning gold from solid ore, the matrix of minerals and rocks must be crushed and ground to sufficient fineness to liberate the gold. The liberated gold could be treated similar as free gold from placers. Gold is mainly separated from the valueless gangue (barren rock) by utilizing the difference between the density of the impure native metal (density about 16-19) and the gangue (density about 2.5). In simple operations the material is carried by a stream of water down a sluice generally equipped with small transverse barriers (riffles) against which the gold collects. The riffled sluice is the principal device used by artisanal gold miners. Nowadays, spirals as well as centrifuges, such as Knelson separator or Falcon separator, are occasionally applied for gold recovery. Gold may also be recovered from the pulp, by passing it over corduroycovered tables that catch the heavier particles - a method maybe as ancient as gold mining itself. In history, sheep skins were used to catch gold particles in this manner. Furtheron, gravity separation of gold is practiced on jigs, hydraulic traps, shaking tables and

Jan 1, 1995

By V. B. Achanti, A. W. Khair

Introduction Laboratory studies were carried out at West Virginia University to investigate the rock-fragmentation mechanism of continuous miners using an automated rotary cutting simulator. The primary factors influencing the fragmentation process were found to be bit spacing, bit geometry, depth of cut and cutting-drum rotational speed. This paper presents a discussion of the effects of these parameters in achieving optimum energy consumption and minimizing dust generation during rock fragmentation. The removal of rock ridges/walls between adjacent grooves is analyzed with three hits mounted simultaneously on the cutting head, while the bit tip angle was varied from 600 to 900. Bit spacing was varied from 25.4 to 50.8 mm (1 to 2 in.) while the cutting process was assessed for varying cutting depths. Respirable dusts generated during the course of the experiments were analyzed utilizing cascade impactors. Assessment of these parameters has led to a better understanding of the cutting mechanism of continuous miners in terms of energy consumption and dust generation. A review of the literature revealed that a considerable amount of research has been carried out on rockcutting processes. Many authors agree that the mechanical cutting efficiencies of mining machines (e.g., continuous miners, shearers and road headers) are affected by a host of parameters. Some of these parameters are machine controlled, some are operator controlled, while others are uncontrollable. Efforts were focused on understanding the influence of parameters such as bit spacing, cutting depth, attack angle, bit type, drum speed, bit geometry (i.e., tip size, shape and tip angle) and rock type on the cutting process efficiency in terms of specific energy consumption and respirable dust generation (Strehig?? et al., 1975, Hanson et al., 1979, Khair et al., 1989). Roepke et al. (1976) in an attempt to study the dust and energy generated during coal cutting using point attack bits found that the dust and the specific energy consumed both decrease as the depth of cut increases. The four fundamental stages of dust generation luring rock fragmentation are identified by Zipf and Bieniawski (1989). Coal breakage by various types of wedges was assessed by Evans and Pomeroy (1966) in an extensive experimental study on British coals. Yet the industry today requires further attention and guidance to optimize the energy consumption and dust generation during the rockbreakage process. This paper attempts to give a better understanding of the influence of some of the parameters listed above and focuses on further improvement in the rock-cutting process. The specific energy consumed for different types of bits used and the respirable dust generated are analyzed in the context of the variation of a few other parameters. Laboratory investigation The experiments were performed in the Rock Mechanics Laboratories located at West Virginia University. A rock-cutting simulator designed and fabricated by Khair (1984) was utilized for this purpose. The details of this machine are available in the literature (see Khair 1984). For this study, a series of preliminary experiments was carried out to determine the optimum cutting frame advance speed. This was intended to facilitate a maximum cut depth of 31.75 mm (1.25 in.) at an advance rate of 0.525 mm/s (0.0207 ips) for all types of bits being used and various bit spacings being considered. To look into the cutting-process efficiency of a continuous miner in the laboratory, several parameters of influence are being considered. Besides the bit-geometry parameters, machine- and operator-controlled parameters, such as spacing of bits on the cutting head, the cutting head rotational speed and the total cutting depth during an experiment, are varied. At the time this paper was written, only part of the completed experiments were ana¬lyzed, and a number of experiments were still being carried out following an orthogonal fractional factorial experimental plan to assess the effect of all of the above¬mentioned parameters on the cutting efficiency in terms of energy consumption and dust generation. Three different types of tip angles, namely, 60°, 75° and 90°, and two different tip sizes, namely, diameters of 7.94 and 24.61 mm (0.313 and 0.969 in.), were used. At

Jan 1, 1999

By Charles T. Steuart, Richard B. Berg

Tripoli and the related mineral commodities such as micro- crystalline silica have been mined for more than 100 years for their abrasive properties. Although abrasive and buffing compound markets are still very important, within the last 15 years the filler and extender markets in paint, plastics, rubber, adhesives, and sealants have increased substantially. Tripoli or microcrystalline silica consists almost entirely of very small quartz crystals, many less than one micrometer in length. Material mined from different districts differs in crystal shape, grain size, and texture of the rock, all of which influence markets. Most US deposits are now mined by surface methods, and both air floated and micronized products are marketed. Deposits of tripoli now mined in the United States occur in chert-bearing Paleozoic limestone in the central part of the country with producing districts in southern Illinois, central Arkansas, and eastern Oklahoma. Although deposits within each district are confined to specific formations and extend laterally within those formations, individual bodies form minable deposits that are typically several hectares in areal extent. Tripoli is white to cream to rose and characterized by high porosity and ease of disaggregation. DEFINITIONS Tripoli In the United States, tripoli was first used to describe the fine-grained, easily disaggregated material from Seneca, MO, be- cause of its similarity to a rock from the Tripoli region of North Africa (Hovey, 1894). The North African rock is actually diatomaceous earth, a material that is similar in appearance to the rock from Seneca, but is of entirely different origin having formed by the accumulation of siliceous remains of microscopic marine or fresh- water animals. Tripoli is best defined as a very fine-grained, generally porous rock that consists of microcrystalline quartz, typically formed by the alteration of a chert-bearing limestone. Tripolite A term used to describe a rock from the vicinity of Tripoli in North Africa which is diatomaceous earth (Quirk and Bates, 1978) Microcrystalline Silica Microcrystalline silica is the same material as tripoli, but the distinction between the use of these two names is dictated largely by convention and markets. Material produced from southern I1linois deposits and used in white pigment and filler applications is generally referred to as microcrystalline silica, whereas that used in abrasive applications, both from the Illinois district and from other states, is commonly called tripoli. Amorphous Silica Amorphous silica, a term formerly used to describe the material produced from the deposits in southern Illinois, is now replaced by the term microcrystalline silica. Amorphous silica came into use when even optical methods for the identification of very fine- grained quartz were not widely available and the Illinois product, composed of quartz grains too small to be seen with the unaided eye, was thought to consist of amorphous silica. The Illinois material is clearly crystalline quartz, as shown by X-ray diffraction analysis and scanning electron microscopy (Fig. 1). Novaculite Although originally used to describe a rock suitable for the manufacture of whetstones, novaculite is now defined more generally " - as a homogeneous, mostly white or light colored rock, translucent on thin edges, with a waxy or dull luster, and almost entirely composed of microcrystalline quartz" (Steuart et al., 1983). The more compact rock mined in central Arkansas from the Arkansas Novaculite is referred to as novaculite, whereas the more porous rock is referred to as tripoli. Rottenstone The commodity rottenstone is sometimes included within the general mineral commodity category of tripoli. Rottenstone is mined in Northumberland County in eastern Pennsvlvania and formed by the weathering of a siliceous shale of Devonian age (Faill, 1979, Berkheiser, private communication, 1991). This material is used as a filler and extender, but is apparently unlike tripoli both in origin and physical properties. Spiculite Spiculite is a rock consisting of siliceous sponge spicules having formed by the removal by solution of the carbonate matrix of a spicule-bearing limestone. Spiculite has been mined in Texas and, because it resembles tripoli in several aspects, is included in the discussion of deposits.

Jan 1, 1994

By William S. Pintz, William A. Vogely, Charles J. Johnson

This chapter on the role of minerals in developing economies is oriented toward economic policy issues. The discussion and analysis cut across the technical, economic, legal, and policy fields. The goal of this chapter is to pro- vide relevant background information important to individuals involved with the minerals sector in developing countries. Where possible, trends are shown to provide a basis for understanding the evolving role of minerals in developing economies. This chapter is divided into the following five sections: (1) characteristics of developing countries (which presents selected statistical comparisons); (2) government objectives in developing countries; (3) government policy formulation in developing countries; (4) determinants of future trends, and (5) a summary of the chapter&apos;s major points combined with the authors&apos; view. CHARACTERISTICS OF DEVELOPING COUNTRIES There are 155 nations in the world categorized as "developing countries." In total these nations represent about one third of the value of the world&apos;s mineral production, three quarters of the world&apos;s population, and over half of the world&apos;s land surface area. The group of so-called developing countries is quite diverse and there are exceptions to almost any general observation about the group as a whole. Most definitions of the term "developing country" are based on levels of per capita income. However, if per capita income is the sole criterion used in categorization, then several oil-exporting countries would jump from the category of developing country to the category of developed country.a Obviously, this results in a poor fit with respect to other measures. In general, the majority of developing countries can be characterized by relatively low per capita income, high population growth rates, high levels of unemployment, low levels of education, short average life ex- pectancies, income distribution skewed toward the highest 20% of the population, and a large share of exports represented by primary commodities. b For the purposes of this chapter a slightly modified version of the widely used World Bank system of classification (shown in Table 1.2.1) is used. As summarized in Table 1.2.1, developing countries are divided into three main groups based on estimated gross national product (GNP) per capita. It should be noted that the high- income, oil-exporting countries have characteristics of both developing and industrialized countries; however they are included for most statistical comparisons within the group of developing countries. Of the 155 developing countries in the world, approximately half produce minerals other than common building materials, and only 32 account for more than five percent of world pro-

Jan 1, 1985

By Robert M. Stevens

INTRODUCTION Truck haulage of muck in underground mining operations has been in use around the world for many years. From the late 1.950s into the early 1970s, haulage by means of load-haul-dump (LHD) units challenged haulage by means of trucks, and, to a large degree, LHD units dominated the trackless concept of moving mate¬rial underground. However, beginning in 1975, the emphasis began to shift back to the use of trucks, with LHD units assuming the secondary role of loading the trucks. Over the years, several manufacturers have been offering trucks with capacities ranging from 4.5 to 45.4 t (5 to 50 st) and with features that specifically address the constraints of underground operation. TRUCK TYPES Three different types of trucks are available for use underground, namely the tip dumpers, telescoping dumpers, and push-plate dumpers. The following para¬graphs describe each of these three types. Tip Dumpers Tip dumpers are designed to lift the truck box, using gravity to dump the load out the rear of the box. The primary application of these trucks is in the haulage of muck to the surface. However, these trucks also may be utilized underground, if a chamber is provided to accommodate the raised truck box at the dumping point. Fig. 1 illustrates a four-wheel drive truck with a 10.0-t (11-st) capacity; this truck is only 1.9 m (6.25 ft) wide and is designed specifically to follow narrow and winding vein courses. Fig. 2 illustrates a two-wheel drive tip dumper with a 24.5-t (27-st) capacity; this truck operates on 12% grades with firm dry surfaces and in modes both loaded-up and loaded¬down. Telescoping Dumpers Telescoping dumpers specifically address the constraints imposed by low back heights, and they represent an optimization of compressed envelope size with maximum payload capacity. Figs. 3 and 4 illus¬trate a typical telescoping dumper with a capacity of 18.1 t (20 st). Fig. 3 shows the box in position for carrying the load, and Fig. 4 shows the same truck with the box in the full-dumping position. Fig. 5 illustrates the loading and dumping cycles. Fig. 6 illustrates an approximation of how an LHD unit with an eject-o-dump (EOD) bucket would be used to load over the rear of this type of truck. Fig. 6 shows a low-profile telescoping truck in the first stage of loading, with a 6.8-t (7.5-st) LHD unit equipped with an EOD bucket. A loader with a smaller capacity and a narrower bucket would allow the bucket to fit inside the truck box and would achieve an even lower loading height than that illustrated. Gen erally, an LHD unit equipped with an EOD bucket and teamed with a telescoping dump truck can be used with a lower back height than could any other front-end loader and truck team. Push-Plate Dumpers Push-plate dumpers are similar to telescoping Bump¬ers, except that they do not have the two-stage box. Instead, push-plate dumpers utilize a single push plate to discharge the load out the rear of the box. Gen erally, these units are limited to payload capacities of about 9 t (10 st). Fig. 7 illustrates a typical push-plate dumper.

Jan 1, 1982

By William E. Cutcliffe, John A. Ames, John D. MacFadyen

Webster&apos;s dictionary nearly equates portland cement with its current primary definition of cement. Although such equation may be a triumph of common usage, the confusion between the terms cement and concrete unfortunately is very widespread. Full definition of cement properly would extend to many substances, but for purposes of this chapter cement is restricted to varieties of portland cement including portland-pozzolan cement. Among the usually recited historical notes concerning cement is that it was developed by the Romans. Their use of cement in the great structures of Rome, and even in the far comers of their Empire, such as Hadrian&apos;s Wall in the north of England, testifies to the antiquity of a major cement industry. From English sources we know of John Smeaton&apos;s carefully proportioned hydraulic cement mixed in 1756 and of Joseph Aspdin&apos;s patented cement to which, in 1824, he gave the name portland cement. (He claimed that his cement mortar looked like the famous dimension limestone quarried from the Isle of Portland on England&apos;s south coast.) The year 1971 marked the centennial of portland cement manufacture in the United States. A fair historical account of the many real contributors to the cement industry since 1756 unfortunately would be too extensive for this chapter. Development of rotary kiln practice and burning at higher temperatures clearly was the major move into today&apos;s technology. Cement manufacture is the processing of selected and prepared mineral raw materials to produce the synthetic, mineral mixture (clinker) that can be ground to a powder having the specified chemical composition and physical properties of cement. Cement making incorporates a number of distinct steps, but it is characterized by the key pyroprocessing (or burning) step, which brings about the necessary changes in the raw materials. This pyroprocessing is a chemical process. Conversion of large volumes of mineral raw materials into specification-controlled cement at relatively low cost is the objective. Statistics on the cement industry are of uneven quality. The US Bureau of Mines (USBM) is the principal collector of available data. These statistics can be only as good as the quality of information supplied by the reporting companies. The data perhaps most often questioned relates to productive capacity of the industry. The questions submitted by USBM are valid, nevertheless, and the information gained from them, as good as is available, is what is generally used. The Portland Cement Association also is a source of much quality information. In analyzing cement industry production rates, it is well to keep in mind that measurement of raw materials requires the reader to recognize that approximately 1.6 t of dry raw materials are required to make 1 t of clinker. This number can vary depending on the amount of kiln dust wasted. Also that to produce 1 t of portland cement required .94 to .96 t of clinker, the remainder being gypsum or anhydrite. A ton of masonry cement or pozzolanic cement re- quires considerably less clinker.

Jan 1, 1994

By P. R. ZETTWOOG

HISTORICAL BACKGROUND A program in France to develop personal [a] dosimeters has been initiated 1974. The patent on which is based the present device was obtained in 1972 * . From 1972 to 1974, the possibilities of applying certain ionograph track detectors to the spectrodosimetry of radon daughters was explored. The first prototype were produced in 1974. It took four years (from 1974 to 1978) to produce an autonomous dosimeter whose components has a sufficient life span, especially for the turbine motor unit. Qualification in the laboratory was obtained in 1977. In 1978 it was obtained in the mine for technology (autonomy of 12 hours and a life span of more than one year) and in 1980 for monitoring. 300 dosimeters have been tested in underground mines all together. Indispensable peripheral equipment were also developed from 1976 to 1980 : calibration devices, equipment to prepare and develop the films, read out systems. The concept of an "Integrated System of Individual Dosimetry" (ISID) based on a personal [a] dosimeter measuring exposure to radon daughters, thoron daughters, ore dust and external irradiation doses was proposed at the end of 1980. Since January 1st 1981, ISID is used on a routine basis in some french mines, situated in remote area, and appears to be very competitive with the ambiant dosimetry. The latest version of the dosimeter is produced in mass series since June 1981 and should equip all french mines in 1982. DESCRIPTION OF THE INSTRUMENTATION DEVELOPMENT OF THE DOSIMETER MEASURING HEAD The measuring head is based on the use of ionographic film to detect a tracks. In fact, the measuring head is a spectrodosimeter which measures separately over the period of exposure: - the potential [a] energy inhaled due to the decay of Po 218, Po 214, and Po 212 ; - the number of Rn 222 atoms inhaled ; - the inhaled total [a] activity of the five long-lived emitters present in the ore dust. The contribution to the total inhalable potential [a] energy of these various radionuclidesin a typical underground mine is studied in Appendix I. The measuring head described in detail in Appendix II, is able to satisfy all the implications made in the ICRP recommendations. Appendix III deals with the use of this measuring head in the cases where the equilibrium factor is lower than 0.1. This situation occur in open-pit mines where account must be taken of the Rn 222 contribution, which is no longer negligible in relation to that of its daughters. CURRENT DOSIMETER PERFORMANCES Table I shows the characteristics of the latest dosimeter. Appendix IV should be consulted concerning qualification of the dosimeter in the laboratory and in mines, technological development which finally produced the [a] dosimeter and its peripheral equipment, and technical presentation of the ISID (Integrated System of Individual Dosimetry) based on the concept of a multirisk personal dosimeter. Data on the installation and operating costs of such a dosimeter, which would seem to be competitive, are also given in this Appendix. ADVANTAGES OF PERSONAL DOSIMETRY AS COMPARED TO AREA MONITORING The results of the first eight months of experiments carried out under real conditions in an underground mine site are given in detail in reference 8. Area monitoring : The monthly exposure per worker to inhaled Rn 222 was determined from the knowledge of time spent in various areas of the mine and for the different mining operations, as well as from numerous and systematic sampling of the Rn 222 concentration in all work places. Personal dosimetry : The exposure to potential energy from radon daughters was measured by an [a] dosimeter developed by the CEA and worn by each of the 160 miners during eight months. In this way 160 x 8 pairs of monthly individual exposure values have been obtained which can be statistically studied. This test was decisive for us because it proved that the [a] dosimeter was technically sound (very few defects over one year for 160 dosimeters) and especially that personal monitoring devices were superior to area monitoring devices. The following conclusions can be drawn 1. The exposure distribution obtained by personal dosimetry is log-normal. This is true for the results on the whole as well as for groups of results relating to certain explanatory variables. See fig. la, 1b, 1c. 2. The exposure distribution obtained by area monitoring does not correspond to any type of distribution. If the results of personal monitoring are taken as a reference, area monitoring tends to underestimate the high exposures and overestimate the low exposures.See fig. 2. 3. [a]-energy exposures are underestimated when calculated from radon exposures and the equilibrium factor found in the considered mines. This is due to episodes or to zones of high radon concentrations not registered

Jan 1, 1981

By Austin Whillier

INTRODUCTION Use of air-cooling or refrigeration equipment in underground mines is needed when conventional ventila¬tion techniques do not maintain acceptable environ¬mental temperatures in working areas. Because refrig¬eration can be very expensive, it should be implemented only after all possible and practical steps have been taken to eliminate or reduce heat sources in the mine. As an example, to prevent the main ventilation fans from contributing heat to mine air, they should be located in the air return and not in the air intake. It is particularly important to prevent any direct contact between hot water and ventilation air, especially in mines which encounter large flows of hot fissure water. Any water hotter than the prevailing wet-bulb temperature of the ambient air must be removed by pipes located as close as possible to the water source. This hot water must not be allowed free contact with the incoming ventilation air at any time during the water&apos;s passage out of the mine. Although insulation of the pipes carrying the hot water is seldom necessary, direct contact between the air and the water must be prevented so the warm water cannot evaporate. REVIEW OF COOLING PRACTICES Spot Coolers vs. Centralized Refrigeration To eliminate a few specific hot places in an otherwise cool mine, it is possible to use devices known as "spot coolers." A typical spot cooler that uses chilled water is shown in Fig. 1. These devices consist of self-contained refrigeration units that are often mounted on rail cars for haulage to hot spots. The cooling capacities of such spot coolers usually are limited to about 100 kW or 30 "refrigeration tons." A refrigeration ton represents a cooling rate that produces 1.0 st of ice in 24 hr; that is a cooling rate of 3.517 kW (200 Btu per min). Typically, the electric-power consumption to drive the compressor motor of the refrigeration plant in mines is 1.0 kW per refrigeration ton, corresponding to a coefficient of per¬formance of about 3.5. The principal difference between spot coolers and centralized refrigeration plants is the method of re¬jecting heat from the refrigeration system. Centralized refrigeration plants always discharge heat into the reject or return airflow of the mine; often that is the primary influence in selecting the location for the underground refrigeration plant. Heat from spot coolers usually is rejected into drain water or into air that is not flowing to the location requiring the cooling. As a result, spot coolers remove heat from troublesome hot spots in the mine, injecting that heat-plus the electrical energy used by the cooling unit itself-into other working areas where the ambient conditions are cooler. In effect, this is "robbing Peter to pay Paul." In deep, extensive mines, spot coolers usually pro¬vide only temporary and, over the long term, expensive solutions to localized cooling problems. Centralized re¬frigeration plants are preferred for such mines, with cooling distributed throughout the mine as required. Fig. 2 illustrates a typical underground centralized re¬frigeration plant. Centralized plants lend themselves to improved maintenance at reduced costs while offering the economy of size. Refrigeration plants of larger unit sizes have considerably lower initial costs than smaller unit sizes. The remainder of this chapter is devoted to large refrigeration plants, with no further consideration of spot coolers. Cost of Refrigeration Total Cost: The total cost of refrigeration amounts to about $200/kW of cooling per year (1981 US $). This total cost breaks down into approximately three equal parts: 1) Financial charges, which include the interest and amortization on the capital cost of the initial installation, and the cost of necessary underground excavations. 2) Operating and maintenance costs which include the cost of the electric power to drive the refrigeration plant&apos;s compressors. 3) Distribution costs which include costs for pump¬ing, insulated piping, and air-to-water heat exchangers. The local cost of electric power, the number of operating months per year, and the method of refrigera¬tion distribution all contribute to the actual costs in¬curred in a given application. However, the variations usually are limited to no more than ±30% of the $200/ kW per year total cost figure. Cost Per Ton: Refrigeration cost per ton of mineral production can be calculated if the annual production tonnage from the refrigerated section of the mine is known. In most cases, this cost will be less than $1 .00/t. However, in deep mines with high rock temperatures, such as those found in South Africa, the total cost of refrigeration can increase to several dollars per ton of broken rock. Distribution In deep extensive mines, distributing refrigeration often accounts for about half the total cooling costs. As a result, careful consideration and planning must be

Jan 1, 1982

By James P. Connell

HISTORICAL BACKGROUND The American Concrete Institute defines shotcrete as "mortar or concrete conveyed through a hose and pneumatically projected at high velocity onto a surface." This definition thus includes what is traditionally known as gunite, which is a pneumatically applied mortar. In mining practice, the term shotcrete is restricted to pneumatically applied concrete, and this differentiation will be used in this chapter. In 1914, following the invention of the mortar gun in 1907, then chief engineer of the US Bureau of Mines (USBM) George Rice developed the gunite process for underground test work at the USBM facility at Bruceton, PA. After World War I, gunite was used extensively in American mines and was also utilized for underground civil works such as the San Jacinto tunnel in California. The greatest development was in Europe where, as early as 1911, gunite was successfully used as an overlay for deteriorated tunnel linings. In 1951, the Swiss firm Aliva developed a pneumatic gun capable of handling coarse aggregate, thus making possible the first use of shotcrete at the Maggia hydropower development. Initially, shotcrete was used to reduce manpower requirements for forming and placing conventional concrete. However, by 1954 Sonderegger was reporting that the structural advantages of shotcrete were derived from its flexibility and from the fact that it could be applied almost immediately after the opening had been made. The incorporation of wire mesh into the shotcrete led to the new Austrian tunnel method or NATM. The use of shotcrete in American mines has been implemented more recently. This delay seems to be due to previously unsuccessful experiences with gunite as a structural material and to the US reliance on wood or steel supports in main-line haulageways. The long experience with the apparently more substantial rigid supports led mine operators to be reluctant to accept the new and seemingly unrealistic lighter shotcrete support. APPLICATION REQUIREMENTS Shotcrete is a relatively new material for use in underground support systems. Consequently, experienced miners are not always available who are capable of applying the material effectively. Shotcrete, particularly in the small cross sections typical of mine shafts or haulageways, is applied in cramped quarters under less than ideal conditions. Adequate lighting should be made available. The surface should be clean and free of running or dripping water. It may be necessary to collect flowing water in plastic pipes or water collection devices. Any dry cement dust from previous shotcrete applications should be washed from the surface in order to assure a good bond. The US Bureau of Reclamation (USBR) while shooting test panels at the Cunningham tunnel in 1974, found that experienced shotcrete operators were able to obtain up to three times greater compressive strengths than were obtained by unskilled operators using the same equipment and shotcrete mix. ENVIRONMENTAL AND SAFETY REQUIREMENTS Since sodium and potassium hydroxide, as well as other moderately toxic compounds, are often contained in shotcrete (particularly where accelerators are used), safety precautions must be taken to prevent skin and respiratory irritation. Nozzlemen and helpers are required to wear gloves, protective clothing, and ventilation hoods with a filtered air supply. Respirators approved by USBM, equipped with chemical filters that will not pass the caustic mists, may be permitted in lieu of hoods if goggles or safety glasses are worn. Protective ointments are available to reduce skin irritation. All air and shotcrete feed hoses should be equipped with safety-type couplings and secured with safety chains at each coupling to prevent whipping in the event of a hose or coupling failure. Some environmental effects can take place down-stream from the development face being supported. The accelerator compounds, as well as the portland cement used in the shotcrete, will be found in the rebound material which falls to the invert of the heading. Since these compounds may be leached from the rebound material and carried by the drainage system, it may be necessary to install neutralizing or other water treatment facilities. Investigations may find that the final reaction with other compounds being leached from the mining operations may result in a more or less environmentally acceptable end product. USES OF SHOTCRETE General Uses Shotcrete, as a combination of cement, aggregate, and accelerator, is utilized for underground openings such as shafts, adits, haulageways, and service chambers for the following general purposes : (1) primary sup¬port; (2) final lining; (3) protective covering for excavated surfaces that are altered when exposed to air (the protective covering may be of a temporary or final nature); (4) protective covering for steel or wooden supports, rockbolts and rockbolt plates, heads, nuts, and other mats, including wire fabric, used to prevent rock-falls; and (5) as a lagging material in place of timber, steel, or concrete between steel or wooden supports. These applications can be grouped into three general use categories: shotcrete used as a rock sealant, shotcrete used as a safety measure, and shotcrete used as a structural support. Use as a Rock Sealant Thin applications of shotcrete can reduce or prevent slaking of shales or other rocks that are altered when exposed to the wetting and drying cycles created by mine ventilation circuits. While shotcrete may be effective in preventing such rock alteration, at the present time it is not as economical or efficient as other commercial sealants. However, if the sealant property can be incorporated into the structural support capability, the added contribution is usually helpful. Thin applications are not usually sufficient if the alteration of the

Jan 1, 1982

By Michael A. Linkous, Mark J. Zdunczyk

Silica in the form of sand and sandstone is one of the most common, and at the same time, unique industrial minerals. Found in every rock type of every geologic age and virtually everywhere in the world, silica is used in products that touch just about every aspect of daily life. Imagine a world in the 1990s without computer chips, fiber optics, or glass, and you have just begun to understand how important silica is to the quality of life we enjoy. The elements silicon (Si) and oxygen (0) comprise roughly 60% of the earth&apos;s lithosphere to a depth of about 16 km. The crystal structure of silicon dioxide consists of one atom of silicon bonded to four surrounding atoms of oxygen to form a three-dimensional network of SiO, tetrahedra. This network makes up the mineral quartz (Murphy and Henderson, 1983), the most common detrital mineral in most sandstones. Quartz is also a major constituent of many igneous and metamorphic rocks and is widespread as a siliceous cementing agent in various rock types. Although quartz is common, sandstones, quartzites, and pegmatites and the unconsolidated sediments derived from them that have a silica content high enough and pure enough to meet today&apos;s market demands for quality and consistency are not common. USES AND SPECIFICATIONS Silica sand that is mined and processed for industrial uses must conform to the chemical and physical specifications set by customers. In the United States almost half of the silica sand produced is used in the manufacture of glass. Other important products include foundry sand, ground silica, blasting sand, and fracturing sand. Glass Sand Silica is the principal glass-forming oxide in a glass batch. Glass manufacturers develop model specifications for each source of silica sand used. These specifications broadly define the limits and ranges for chemical and physical properties of the sand and are used by the manufacturer in calculating the desired batch mix or formula. Some specifications may be critical to a glassmaker and require very stringent limits on the quantity of impurities in the sand. For example, the total iron oxide content of a batch is extremely crucial when making white or flint glasses (Mills, 1983). Iron is present in almost every raw material used in a glass batch and must be carefully controlled in order to obtain a consistent color in the finished product. It is difficult, however, for a raw material supplier to tightly control the chemistry of a naturally occurring material such as silica sand. To a great extent the commercial quality of a sand is determined by its geologic history. Realizing this, glass producers tailor their model specifications to each source of approved material. In general, a glass company is concerned most about the consistency of raw materials on a day-to-day basis. Soda-lime-silica glass was the earliest type of manmade glass (Baker-Can, 1967) and still accounts for most of the glass manufactured for commercial use today (Mills, 1983). It is relatively easy to melt and shape and is less expensive per ton to produce than most other types of glass (Baker-Can, 1967). Soda-lime-silica glass is used in fabricating containers, flat glass products, incandescent and fluorescent lamps, glass fiber, and many other products. Heavy minerals such as ilmenite, leucoxene, kyanite, and zircon are impurities on which strict limits are placed for a glass batch. Because of their refractory nature they either do not melt or only partially melt, which results in stones or feathers in finished glass. Aluminosilicates such as kyanite also contribute unwanted alumina to the batch as they partially melt. Limits are especially rigid for refractory mineral grains coarser than 0.60 to 0.425 mm (30 to 40 mesh). [Tables 1 and 2] present typical specifications for silica sand used in flat glass and container glass products. The percentages shown represent an average of many companies7 specifications.

Jan 1, 1994

By Bruce Hebblewhite

"Historically there have been a number of different hypotheses and empirical models developed in an attempt to describe the nature of fracturing above longwall panels in underground coal mining. The motivation for such models varies, ranging from understanding the impact of mining on surface subsidence to back-analysis of caving behaviour in the immediate roof behind the longwall face. One of the most critical motivating factors that is taking on increased importance in many coalfields is the need for better understanding, and hence prediction of the impact of mining on overlying strata, particularly strata units acting as aquifers for different groundwater horizons.This paper reviews some of the major prediction models in the context of observed behaviour of strata displacement and fracturing above longwall panels in the Southern Coalfields of New South Wales, south of Sydney. The paper discusses the parameter often referred to as “height of fracturing” in terms of the critical parameters that influence it, and the relevance and appropriateness of this terminology in the context of overlying sub-surface subsidence and groundwater impact. The paper proposes an alternative terminology for this parameter that better reflects what it is and how it is used. The paper also addresses the potential role of major bedding shear planes mobilised by mining and their potential influence on overlying subsidence and groundwater interference.INTRODUCTIONKnowledge of the detailed nature of rock deformation and failure above any form of large-scale underground mining is always going to be limited to interpretation from a very incomplete set of data. It is extremely difficult, if not impossible, to directly measure the detailed nature of the rock failure, fracture networks, and deformational behaviour above an extracted mining area. Limited techniques such as borehole extensometry can provide some evidence of relative or incremental deformation in the direction of the borehole (usually vertical). However, such data cannot assist below the horizon where full caving has caused major rotation and dislocation of rock blocks and effectively destroyed the instrumentation borehole. Above such a horizon, the data is only valid along the axis and in the direction of the borehole, and to the level of detail defined by the extensometer anchor spacing intervals. It is often also restricted by major shear planes intersecting the extensometer borehole and cutting off the instrumentation below the level of the shear horizons."

Jan 1, 2019