Search Documents

By Gerald Stolarczyk

The Radio Imaging Method (RIM) is based upon electromagnetic (EM) wave propagation in the coal seam waveguide. The radio geophysics theory underlying RIM was developed by Hill of the national Institute for Science and Technology (Hill, 1984). Recent advances in radio geophysics instrumentation have increased operating range in the coal seam waveguide to almost 3,000 feet. This paper describes RIM longwall panel reconnaissance scans and tomography results.

Jan 1, 2006

By Khaled Morsy

Cementitious seals are made of foamed cements with strength ranging from 100 to 600 psi. These cementitious seals are usually used at locations where the seal will be subjected to some convergence, assuming that this material can absorb entry closure without compromising the structural integrity of the seal. Prior to 2006, Lake Lynn Experimental Mine (LLEM) conducted full-scale tests on various cementitious seals designed to meet or exceed the 20-psi horizontal static load requirements of the old 30 CFR1 75.335. Both hydrostatic and dynamic loading tests were conducted. The structural response (pressure and displacement readings) obtained from these tests were recorded. The stability of the cementitious seal is based on balancing the load applied to the face of the seal from the explosion against the shearing resistance at the seal/rock interface. Therefore, the properties of the seal/rock interface, such as stiffness, cohesion, friction, etc. are critical to determine the stability of a cementitious seal. These properties are usually assumed by the researchers in their models. This paper emphasizes the importance of having the correct properties of seal/rock interface in the numerical modeling. FLAC 3D models were developed to simulate Celuseal2 cementitious seals subjected to both hydrostatic and dynamic loadings. Using the hydrostatic and dynamic loading test data conducted at LLEM, the static and dynamic properties of the seal/rock interface were back calculated. The FLAC 3D models showed good agreement with the test results.

Jan 1, 2009

By Christopher Mark

Knowledge of in situ stresses is fundamental to many studies in earth sciences, and coal mine ground control is no exception. During the past 20 years, it has become clear that horizontal stress is a critical factor affecting roof stability in underground coal mines. The theory of plate tectonics and the World Stress Map (WSM) project has been extremely helpful in explaining the sources and the orientations of the horizontal stresses observed underground. Recently, WSM geophysicists studying deep-seated stresses have developed a model of how stress magnitudes vary with depth in the crust. They have devoted relatively little attention to near-surface stresses, however. This paper explores the relationships between deep-seated and shallow in situ stresses in several of the world?s coalfields, using a data base of more than 350 stress measurements from underground coal mines. The analysis indicates that distinct regional trends exist, corresponding roughly to the regional stress fields identified by the WSM. The paper presents equations for estimating stress magnitudes that were developed by treating depth and elastic modulus as independent variables in regression analysis. The magnitude of the horizontal stress increases with depth, at rates that range from 0.8 to 2.0 times the vertical stress, just as the WSM ?critically stressed crust? model predicts. Overall, it seems that the stress regimes encountered in underground coal mines are closely linked to those that exist deep in the earth?s crust.

Jan 1, 2008

By Peter Zhang

Shield recovery in a longwall move is normally conducted from tailgate to headgate. However, if the face is wide and the immediate roof is weak, difficult conditions with considerable roof sag, excessive shield load, and local roof falls could occur as the shield recovery proceeds to the middle of the face, causing delays in shield recovery. The situation could be aggravated when a pre-driven longwall recovery room is employed. Alternatively, a bi-directional approach for shield recovery, i.e. shield recovery starting from the middle of the face towards both tailgate and headgate, can alleviate the roof sag significantly by quickly withdrawing the shields towards the lower abutment pressure zones at the headgate and tailgate sides. In this case, the bi-directional shield recovery approach was used in a longwall move for a 1450 ft wide face under weak roof conditions. Shields were successfully withdrawn within five days without experiencing significant roof sag. The time-dependent roof-to-floor convergence, shield pressure, and roof conditions were monitored during shield recovery. 3-D finite element modeling was conducted prior to longwall move to evaluate the difference between a uni-directional and a bi-directional shield recovery during a longwall face move. Vertical stress, yield zone in and around the recovery room, load on the shields, and convergence at the center of the shield canopy were obtained from computer modeling, and compared with the data from field monitoring. Finally, the advantages of the bi-directional shield recovery are discussed.

Jan 1, 2007

By Wenbing Xie

At Renlou Coal Mine, Huaibei Mine Area, the track entry deformed significantly after longwall mining in an overlying multiple seams. The supporting characteristics of primary roof bolts and shotcrete with wire mesh are closely related to the movement of the mine?s surrounding strata. A case study of a track entry deformation was monitored during the longwall mining of a selected overlying panel. The measured data showed the unique entry deformation pattern during the longwall mining in the overlying seam. Underground extensometer measurement showed that entry stability was mainly affected by the periodic roof weighting of longwall mining in the overlying seam. The displacement of the deeper strata occurred a head of the immediate vicinity of the entry. Thereafter, deformation of the roof and floor strata was in the form of shearing of the shallower strata. Due to the use of heavy-duty roof bolting with wire-mesh, the roof-tofloor and rib-to-rib convergences were small, but the floor heave was large, greater than 80% of the roof-to-floor convergence. The measured displacement from extensometers varied with the position of the monitored cross-sections and depth into the roof. There were several deformation patterns, such as shearing movement, compression, and expansion, and the variations between compression and expansion. Strata compression at the entry surface was always accompanied with shearing movement at the deeper strata. During the longwall mining, the whole surrounding strata of the entry moved toward the opening. Underground practical experience indicated that prior to mining, the entry was supported very well in excellent conditions. After mining, however, it deformed greatly. The current entry support technology was not effectively control the severe deformation incurred in entries driven in soft strata due to the following reasons: (1) little is known about the entry deformation behavior of the strata surrounding the opening and (2) the degree of interactions between entry deformation and roof bolting with wire mesh is not well understood. Consequently, effective supporting systems cannot be properly selected to control its deformation and maintain a stable supported surrounding structure.

Jan 1, 2012

By Kray Luxbacher

Three-dimensional time-lapse velocity tomograms were generated to image stress redistribution around a longwall panel to produce a better understanding of the mechanisms that lead to ground failure. Mining-induced microseismic events provided passive sources for the three-dimensional velocity tomography. Surface-mounted geophones monitored microseismic activity for 18 days. Most similar studies have utilized active sources including longwall shearers, controlled explosions, and hammer blows. These active sources generally require a person to initiate and measure the location and time of the source, and are not conducive to continuous monitoring. This method utilizes mining induced microseismic events as passive sources and lends itself well to continuous monitoring. Two event location methods were compared in order to move toward quantification of tomographic results in terms of ground conditions. Additionally, LAMODEL was utilized to determine the expected stress distribution around the longwall panel and compare these images to the velocity tomograms. Eighteen tomograms were generated, one per day, and high velocity regions in the set of tomograms generated from the initial location algorithm correlated with abutment stress redistribution predicted by numerical modeling. This research is significant as it has the potential to improve safety in underground mines and is the only example of long term passive velocity tomography implementation for the purpose of inferring stress redistribution around an area of active mining. Though still immature, this technology has the potential to allow mine personnel to image areas of active mining on a regular basis and detect areas with anomalous velocity distributions indicating potential safety hazards.

Jan 1, 2007

By Yajie Wang

High horizontal stress and its adverse effects on longwall gate entries have been witnessed in many US coal mines for the past years. It can cause cutter roofs and leads to roof falls either in the headgate or tailgate entries depending on the relative orientation of the panel to the maximum principal horizontal stress. Underground observations have shown that if the maximum principal horizontal stress is perpendicular to the panel entries, the roof is in the worst condition and if the maximum principal horizontal stress is parallel to the entries, the entry is in the best condition. However, little has been done about the high horizontal stress effects on panel entries subject to different orientations of high horizontal stress. In order to design a longwall panel and control the roof effectively, the redistribution and concentration of high horizontal stress field must be fully understood. Using 3-D finite element analysis, this paper presents the high horizontal stress redistribution and concentration for a retreat longwall face with different orientations of high horizontal stress. Based on the results, possible roof failures for different orientations of high horizontal stress are analyzed. A panel design criterion is recommended.

Jan 1, 1996

By J. K. Whyatt

The paper presents an approach to design a multi level room and pillar layout in a 40m thick seam overlain by a major aquifer. The design was required to maximise extraction with due consideration of the general stability of the workings, the potential water hazards, and spontaneous combustion risks due to air leakage between horizons. The approach utilised was a combination of empirical pillar sizing for water hazard control with numerical modelling to assess potential interactions between horizons. The numerical modelling allowed the size of interleaves, and the appropriate staggers to be optimised in terms of stress distribution. The stress distribution allows both the general stability of the openings and more importantly the permeability changes around the openings to be determined. The permeability of coal is sensitive to stress, and an empirical stress to permeability relationship, and theoretical permeability to flow leakage relationship has been applied to interpreting the relative spontaneous combustion risk associated with each of the proposed layouts. The final proposed design is a compromise between maximum exploitation of reserves and consideration of water hazards and of spontaneous combustion risk. Further more detailed design will be required as more comprehensive data on the geotechnical properties of the coal and overburden become available.

Jan 1, 1996

By Peter (Yunqing) Zhang

Longwall recovery under weak roof conditions could have considerable delay if the immediate roof is weak and deteriorates during screening. A pre-driven longwall recovery room is a feasible solution to minimize the impact of longwall move on production. In this longwall recovery project, a 16-ft recovery room was pre-driven to cover screening, and the shearer cut another 16 ft outby to reach the final recovery line. The pre-driven recovery room was carefully monitored as the face was approaching it. The longwall face operated very well as it cut into the recovery room. The recovery process took about 13 days, and considerable time was saved compared with the previous panel. The support in pre-driven recovery room was designed to handle both front abutment pressure and weak immediate roof conditions. Pumpable standing support was used to support the cantilevered roof as the fender pillar narrowed and collapsed when the face cut into the recovery room. To ensure the stability of the recovery room, 3-D computer modeling was used to evaluate the support system. Abutment pressure, critical fender pillar width, bolting system, pumpable cribs and shield support were considered in the model. The recovery room was carefully monitored during longwall recovery. Roof-to-floor convergence and crib convergence were recorded every shift as the longwall face was approaching the recovery room. Roof, floor and pillar activities and crib performance were also observed as the face cut into the recovery room. This paper presents the support design for the recovery room, evaluation of the support system through computer modeling, and details of the monitoring results.

Jan 1, 2006

By W. C. Lacy

Stratabound copper ore bodies in thick Proterozoic metamorphosed sedimentary and volcanic rocks at the Tong Kuang Yu Mine in southern Shanxi Province of China were considered as possibly being amenable to block cave mining. Initial evaluation of caving characteristics was based upon old calyx drilling records, limited underground mining experience and geological mapping, a few diamond drill holes and measurements in surface subsidence features. Classification and mapping distribution of rock quality types aided in mine design, prediction of fragment sizing and explosive requirements, cave assist and ground support requirements. Comparison is made between early feasibility predictions and actual mine experience.

Jan 1, 1989

By Kausik M. Sinha

Hydraulic stowing, which is being practiced in several major coal producing countries to deal with adverse mining conditions, usually permits almost 100% coal recovery from underground mines with minimal and controlled surface subsidence. It can be implemented in the US coal mines to reduce the severe effect of land subsidence and at the same time improve the cost of coal production, both of which are major setbacks for the coal industry in the USA

Jan 1, 1989

By B. G. D. Smart

An understanding of the nature of yield zones surrounding coal mine excavations is fundamental to the design of mine support systems. Various methods have been designed for investigation of underground rock masses and an extensometric technique, the Magnetic Rod Extensometer, has been developed to overcome inherent design limitations in existing equipment of this type. This paper refers to the prototype form of the extensometer and details changes designed to overcome a variety of drawbacks indicated by routine use of the equipment. The principal change has been one of manual to computerised data acquisition and presentation in the laboratory phase of the system. This has dramatically reduced the time taken to process underground measurements and produce numerical and graphical results. The revised Magnetic Rod Extensometer represents an integrated instrumentation system that combines speed and accuracy in all areas of data handling.

Jan 1, 1984

By Christopher Mark

Multiple seam interactions are a major ground control hazard in many U.S. underground coal mines. The two most common types are: ? Undermining, where stress concentrations caused by previous full extraction in an overlying seam is the primary concern, and; ? Overmining, where previous full extraction in an underlying seam can result in stress concentrations and rock damage from subsidence. The National Institute for Occupational Safety and Health (NIOSH) has completed a major study aimed at helping to identify the location and likely severity of these interactions. In the course of field visits to mines throughout the U.S., more than 300 multiple seam case histories were assembled into the largest data base of multiple seam case histories ever collected. These data were analyzed with the multivariate statistical technique of logistic regression. The study also employed LaM2D to estimate the multiple seam stresses, ALPS and ARMPS to determine pillar stability factors, and the CMRR to measure roof quality. The study resulted in the development of a computer program, called Analysis of Multiple Seam Stability (AMSS), which can help mine planners to evaluate each potential interaction and take steps to reduce the risk of ground control failure. AMSS first evaluates pillar design by calculating the single seam Stability Factor (SFSS) using ALPS or ARMPS. It also automatically generates a LaM2D analysis that provides the additional multiple seam stress so that the final, multiple seam SFMS can be determined. The second part of the AMSS procedure builds upon the statistical findings that overmining is much more difficult than undermining, isolated remnant pillars cause more problems than gob-solid boundaries, and weaker roof significantly increases the risk of multiple seam interactions. AMSS quantifies these effects and predicts the outcome in terms of three levels of risk: GREEN (where a major multiple seam interaction is considered unlikely), YELLOW (where adding a pattern of cable bolts or other equivalent supplemental support could greatly reduce the probability of a major interaction.), or RED (a major interaction should be considered likely, and it may be desirable to avoid the area entirely).

Jan 1, 2007

By Jennifer Riefenberg

Ground control hazards, coal quality, ore reserve estimation, and pollution modeling seem unrelated topics from most mining perspectives. However, geostatistical methods can be used to characterize each of these, and more topics. Exploratory drill core data, and continued drilling and field measurements, can provide a wealth of information related to each of the above areas and are often severely underutilized. Recent studies have led to the development of the Multiple Parameter Mapping (MPM) technology, which utilizes geostatistics and other numerical modeling methods, to generate a "hazard index" map, often from exploratory drill core data. This mapping has been presented for ground control hazards relating roof quality, floor quality, numerically modelled stresses due to mining geometry, and geologic features. A review of the MPM method, future directions with the MPM, and a discussion of using these and other geostatistical methods to quantify coal quality, ore reserve estimation, and pollutant modeling are presented in this paper.

Jan 1, 1996

By B. Arjang

ABSTRACT: Ground stresses are one of the significant factors in the context of rockbursts and underground instability at some hard rock mines in Canada. Overcoring strain relief measurements using triaxiaI strain eel is were performed at depths between 60 to 1890 m at several mine sites to provide stress data for stability analysis and optimum mine design. Pre-mining ground stress determinations from 64 stress tensor analyses resulted in the following average stress gradients: Maximum horizontal stress. -Hmax - 8.18 - 0.0122 MPa/m depth Minimum horizontal stress. _-,,min - 3.64 - 0.0276 MPa/m depth Average horizontal stress. -11, 5.91 - 0.03-19 MPs m depth Vertical stress. '-, - 0.0266 - 0.008 MPa/m depth The maximum and minimum horizontal compressive stresses. with an average ratio of 1.75 ,0..45. prevail in east--west and northerly directions. respectively. Horizontal compressive stresses in excess of vertical overburden load were determined. indicating large variations in ratios to a depth of about 1000 m with decreasing trend towards depth. From present data. a particular regional zoning for the magnitude and direction of horizontal stress fields cannot be outlined. A common feature at mines with near vertical orebodies is that the maximum horizontal compressive stress acts perpendicular to strike while the minimum horizontal compressive stress is aligned on-strike. The vertical stress components approach the gravitational overburden load.

Jan 1, 1989

By K. Unkug

It is commonly accepted that the tension of roof bolts can be used as a measure of the effectiveness of roof support performance in coal bearing strata. The conceptual base for the assumption originates from beam theory. Roof bolt tension acting across the bedding and other weakness planes increases friction, preventing potential separation and slippage within the roof strata and therefore, increases the stiffness of the roof beam between the open face and the rock-mass enclosed within the anchorage. Thus, it is important to monitor roof bolt tension, especially for research purposes, and consequently many measuring systems were developed based on numerous working principles. Research planned by the Department of Mining Engineering at the University of Kentucky required a large number of tension measuring devices of high precision. These were intended to operate reliably in corrosive mine environment over long periods of time. After evaluating the existing systems, it was decided to develop a new type of roof bolt dynamometer which would fulfill the above requirements at minimal Cost. Nearly one hundred such dynamometers were constructed, calibrated and installed in two underground mines. They remained in service for a period of one Year, producing a valuable database for the Project. In this paper the working principle of this new type of dynamometer will be described and technical considerations and samples of the collected data will be given.

Jan 1, 1986

By Ray Brandon

The recent introduction of polymer geogrids for ground control purposes in underground mines allows mine operators more flexibility in choosing improved products for several applications. This is evidenced most clearly in longwall recovery operations. Since November, 1994, many mine operators have chosen Fortrac geogrid assemblies for the purpose of securing longwall recovery areas prior to shield removal. Fortrac is a lightweight, strong, and flexible polyester geogrid available in many strengths. Utilizing the "diamond" seaming method, different strengths of Fortrac geogrids are easily fastened together so stronger geogrids may be placed in the most critical areas and lighter geogrids in less critical areas.

Jan 1, 1996

By David Newman

Multiple seam underground coal mining is ubiquitous in Appalachia. Many coal properties have from two to ten or more economically mineable coal seams. Because of the ability to penetrate 600-feet to 1,000-feet or deeper into the mountainside leaving panels of web pillars separated by barrier pillars, highwall mining is a hybrid between surface and underground mining. As a result, many of the ground control problems commonly associated with multiple seam underground mining exist with multiple seam highwall mining. These include: i) superjacent mines, subsidence and caving propagating to overlying seams and ii) mines, pooled water and the potential for inundation resulting from a iii) breakthrough between an active highwall mine and abandoned underground mines in the same or superjacent seams, the presence of overlying or underlying mine workings where iv) pillar columnization in the active mine is not possible, and v) the question of whether to mine ?top-down? or ?bottom-up.? Case histories are presented from southeast Ohio where the Middle Kittanning No. 6 and Lower Kittanning No. 5 seams are successfully highwall mined with 20-feet to 40-feet of largely shale interburden. A highwall miner was caught in a highwall collapse in the Middle Kittanning No. 6 seam when it was overmining auger workings in the Lower Kittanning No. 5 seam. Multiple seam interaction caused by the overmining transferred overburden stress onto the Lower Kittanning No. 5 seam. The overburden concentrated through web pillars initiated auger web pillar failure, resulting in roof collapse and subsidence in the Lower Kittanning No. 5 seam that propagated up to the Middle Kittanning No. 6 seam. A second case history involves multiple seam highwall mining in southeast Kentucky. The A3 Rider, A3, B2, and C1 seams are being highwall mined around abandoned underground mines in the A3 and B2 seams and augering in the A3 Rider. Because of spoil storage constraints for the surface contour mines, the highwall miner follows the active pits in each seam so a standard sequence of ?top-down? or ?bottom-up mining does not exist. The planning and engineering design considerations associated with each case history is presented along with geotechnical information. In the case of the highwall collapse a back analysis is presented of the stability and safety factors for the auger webs, highwall miner web pillars, and barrier pillars.

Jan 1, 2009

By Thomas Barczak

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear ?abutment? moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

Jan 1, 2007

By Yuanwci Shi

This paper discusses the results of research on the interaction between roof strata and shield supports including the active and passive supporting functions of the shield supports which prevents roof strata separation; pressure distribution on the canopy and under the base plate as measured in the laboratory and underground; comparison between various shield structures regarding their effectiveness on roof and floor control; and determination of optimum support capacity under given geological and mining conditions including hard-tocave roof

Jan 1, 1997