Search Documents

By Gregory M. Molinda

The U.S. Bureau of Mines has developed a rock mass classification system for coal mine roof control. The Coal Mine Roof Rating System (CMRR) evaluates the structural competence of mine roof using simple field tests and observations obtained from underground exposures in roof falls or overcasts. The basis of the WRR is a weighing system which converts descriptive geologic roof rock data to a numerical value, facilitating its use in engineering design. A full suite of data collection and hand calculation sheets accompanies the CHRR A data base is currently being collected from all major coal basins in the United States to validate the CMW. To date, CHRR values are available from 96 roof exposures in 59 coal mines representing these basins. The system can be used to help solve many practical ground control problems, including longwall gate road design, roof support selection, and decisions regarding extended cut length.

Jan 1, 1993

By Anthony T. Iannacchione

Longwall mining produces surface subsidence basins that affect streams by water diminution and contamination. These effects can ultimately impair the biological character of the plants and animal communities living in the streams. The combination of flow, water quality, and ecological effects threaten the environmental sustainability of longwall mining and, ultimately its social acceptability. Pennsylvania has developed new standards, released in 2005 and implemented in 2007, to help protect the commonwealth?s valuable streams from the detrimental effects of subsidence. These standards are aimed at eliminating environmental problems and will therefore help to make underground bituminous coal mining more sustainable. The engineering solutions necessary to comply with these standards are fundamentally affected by the geologic nature of coal-bearing strata, the existing in-situ stress conditions, and the ability of selected species to survive and adapt to changes in their environment caused by longwall coal mining subsidence. Needless to say, geologists, biologists, and engineers are all playing a pivotal role in developing prevention controls and recovery measures necessary to protect streams and sustain underground coal mining. The challenges facing scientists and engineers in sustaining the development of underground coal mining in Pennsylvania are examined through case studies. These challenges all arise from the subsidence effects of longwall mining. The key effects of subsidence, discussed through case studies, are: a) tension cracks, b) springs in headwater stream areas, c) stream gradients and subsidence basins, and d) stream compression ruptures and horizontal stress. All of these potential threats demonstrate the need for high-level scientific knowledge and innovative engineering solutions. One could argue that Pennsylvania?s stringent stream protection standards put the coal mining industry at a competitive disadvantage compared to other coal producing states. It is equally likely that compliance with these standards help to mitigate the effect of subsidence, thereby helping the coal industry achieve a sustainable future.

Jan 1, 2011

By Matthew J. DeMarco

Research personnel at the U.S. Bureau of Mines have conducted longwall gate stability studies at four western U.S. mines attempting to employ yield pillars for improved ground conditions. Located in the Book Cliffs and Wasatch Plateau coalfields of north-central Utah, these operations are generally characterized by multiple-seam mining, cover depths averaging 450 - 600 m (1,500 - 2,000 fl), occasionally extending beyond 760 m (2,500 ft), abrupt cover depth variation due to the overlying canyon/mesa topography, and massive, rigid sandstone roof units. Such conditions encourage severe gate and panel coal bumping, as well as various types of roof instabilities and occasional floor-heave problems. To alleviate these adverse conditions, several mines have employed yield pillars to-reduce hazard-inducing excessive gateroad stress concentrations. This paper describes the evolution of gateroad designs at four of these operations, the specific mining conditions involved, and the general stability performance attained by using yielding gate systems. Mine experiences are "compared" in terms of basic setting conditions, and the general concepts of yielding system applicability and success potential are summarized.

Jan 1, 1993

By Thomas M. Barczak

The initial Support Technology Optimization Program (STOP), Version 1.0, was released at the 19th Gmund Control Conference. This original program has since been updated to Version 2.3 which was released in May, 2001. This paper describes the additional features of Version 2.3, focusing primarily on the following three aspects: (I) including uncontrolled convergence into the design requirements for standing roof supports, (21 the addition of design procedures for cable bolts as an alternative secondary roof support, and (3) the addition of new standing roof support technologies. Another new feature which should facilitate the development of design criteria for standing roof support is the capabilily to define ground reaction curves through convergence measurements alone wthout having to make support loading measurements. There are several other new features provided in Version 2.3 which are only briefly addressed in the paper. These include: (I) additional graphics capabilities to facilitate rapid assessment of support comparisons. (2) an East-West designation for support selection to more accurately provide cost and support availability data, (3) additional safety measures including a safety factor to identify support design near the peak support capacity, checks to see if the support dimensions comply with aspect ratio requirements, and measure of roof coverage for the design layout of the support system These new features of STOP provide more capabilities to design and analyze secondary roof support systems for conditions whlch could not be fully analyzed in the original version of the program.

Jan 1, 2001

By Keith A. Heasley, Jian Yang

"LaModel uses a laminated overburden boundary-element model and can calculate not only seam-level stresses and displacements but also surface subsidence for thin tabular deposit such as coal seams (Heasley, 1998). Up to this point in time, the material property wizards in LaModel have primarily been designed for calculating accurate stress distributions in single- and multipleseam situations, and for investigating and optimizing pillar sizes and layouts in relation to overburden, abutment, and multipleseam stresses. However, the critical input parameters that will give the most accurate seam-level stress distribution do not necessarily produce the best surface subsidence prediction. The objective of this paper is to develop a methodology for calibrating the critical input parameters in LaModel to optimize surface subsidence prediction.For optimum surface subsidence prediction, it was found that the gob convergence (as defined by the final gob modulus) and the overburden stiffness (as defined by the lamination thickness) were the two most critical parameters that needed to be calibrated (Heasley, 2016). By calibrating numerous panels with various widths and depths, a formula that provides the optimum final gob modulus to use for subsidence prediction was developed. Also, three different empirical formulas for optimizing the lamination thickness as a function of overburden depth and/or the panel width to- depth ratio were determined for the three cases: supercritical panels, and subcritical panels with and without offsets. Further, if the user has measured data for subsidence factor and angle-of draw, the optimum final gob modulus and lamination thickness can be determined from the measured data. These new subsidence prediction formulas are being implemented into new material wizards in LaModel.INTRODUCTIONIn the past few decades, with the increased need for highly productive mining techniques, full extraction mining methods have been increasingly employed in the U.S. coal mining industry. These total extraction mining methods, which include both longwall mining and room-and-pillar retreat mining, normally cause immediate roof caving and the associated surface subsidence. These methods can be highly productive and cost-effective, but the associated surface subsidence can cause damage to surface structures and negatively impact the surface environment (Peng, 2008). Therefore, a reliable program for predicting the surface subsidence associated with full extraction mining is required for appropriately engineering and managing the surface subsidence impacts of full extraction mining."

Jan 1, 2016

By Shengli Yang

Solid backfill mining, as a green mining technology, has the advantages of a higher resource recovery, less damage to the environment and the ability to dispose of waste underground. It has been applied successfully in the Xingtai and Xinwen mining areas in China. Strata behavior and the movement of overburden strata in this mining method are very different from fully mechanized longwall mining, which results in a natural caving, because the gob is filled with waste rock, fly ash and other backfill material. The results of field measurements showed that the periodic weighting interval of the main roof is longer; the magnitude of periodic weighting is smaller; the peak and zone of influence of the front abutment pressure are smaller than those in fully mechanized mining; that major deformation of mine roadways occurs within the influence zones of the abutment pressures; that the falling space of immediate roof is smaller, with the lower portion falling more sufficiently than the upper; that the main roof subsides slowly; and that the falling height of the overlying strata is greatly reduced.

Jan 1, 2011

In this paper, the plastic increment theory was applied in a 2-D finite element model, and a generalized Von Mises yielding criterion adopted to simulate the progressive failure of coal pillars. Extensive underground monitoring was conducted and the data compared with the computer model, yielding promising results. Three different longwall entry layouts, including a stable (s-s) pillar system, a yield-stable-yield (y-s-y) pillar system and a yield (y-y) pillar system, were investigated using the model developed. The yield-stable-yield system was considered to be the best of the designs studied in the case. A comprehensive parametric analysis was also performed. The triaxial factor and Poisson's ratio were found to be the most important material parameters affecting pillar yielding.

Jan 1, 1988

By David H. Tang

Similar massive pillar failures were observed in two underground coal mines with different configurations of mine workings and overburden depths. Finite element models were used to analyze the causes and mechanisms of the pillar failure. The results of the analyses confirms the underground observation. For Case No. 1 the failure of coal pillar is mainly caused by a combined effect of smaller coal pillars under a large overburden and the interaction of multiple seam mining. For Case No. 2, the pillar failure was initiated by the weak roof rock but the ultimate pillar failure was caused by the splitting of pillars into very small size.

Jan 1, 1984

By John L. Hill

Cutter roof failure is a specific type of ground control problem which frequently results in massive roof failure. It is a cannon occurrence in coal mines of the Northern Appalachian Coal Sasin, causing delays in production and posing a safety hazard to mine personnel. The Bureau of Mines is conducting research on the causes of cutter roof failure togain a basis from which to prevent its occurrence and to support such roof when failure does occur. Research conducted in a coal mine of central Pennsylvania has revealed a correlation between the occurrence of clastic dikes and fonation of cutter roof failure. Inmine mapping of ground conditions showed an increase in roof failure in areas of high frequencies of clastic dikes. Rock pressure monitoring around clastic dires registered the greatest amount of roof loading near the inter- section of dikes with the rib. Load cells measurim horizontal pressure changes in the roof indicated that the greitest pressure changes were occurring perpendicular to entry headings when clastic dikes were present. Analysts of rock pressure nwnitiring shows that the roof behaved as two cantilever beams when severed by a clastic dike. Additional roof supports such as trusses and cribbing were found to effectfvelv suooort the roof in areas of clastic dikes and prevent cutter roof iailure. However, there lnethads were only successful when employed shortly after mining.

Jan 1, 1984

By Nikolaos Polysos

Besides considering the given geomechanical conditions, the geological/geotechnical logging of drill cores and heading faces during the driving of parallel entries and the resulting rock classification form the basis of the assessment of the proneness to caving of the roof strata in the actual mining phase. Both types of separation planes, parallel to the stratification as well as intersecting the bedding, will be defined and assessed within the immediate roof strata depending on the lithological structure. These data may hold the potential to plan the winning and design its operational organization in a way that - to a major extent - future damage of the workings by increased caving or cavities can be predicted in advance. Following the general description of the separation plane structure, the combined influence of the petrographic and structural geological roof properties on the operating cycle of the planned working face will be presented and illustrated.

Jan 1, 2003

By Kot F. v. Unrug

The depletion of thicker coal reserves has resulted in the thinner seams being economically attractive. Surface protection against subsidence limits the extraction ratio to 50% for the room and pillar method as a "no subsidence condition". That rule was developed for pillars with smaller width/height ratio because seams mined at the time were commonly 6 feet thick. Over time pillar ribs deteriorate around the pillar perimeter and thus decrease the area of the pillar. Using 50% extraction as the no subsidence condition in the squat pillar category (below 42 in with w/h > 7) causes unnecessary losses of reserves because squat pillars are stronger. In this paper a method is presented for design of long-term pillars. Based on the analysis of pillar deterioration and field observations, an increase of the "no subsidence" extraction rate to 60% for squat pillars is proposed.

Jan 1, 2001

By Robert A. Stansbury

The No. 14 Mine of United States Steel Corp- oration is located at Munson, West Virginia, in &Dowell County. The mine was originally assigned 7,530 acres of Pocahontas 3, 4 and 5 Seams. Production began in 1948 with a listed reserve of 64,500,000 in place tons. It was originally intended to superimpose the 4 Seam workings with the 3 Seam and mine the two simultaneously to minimize the effects of one seam on the other. Roof control problems and economic conditions led to the discontinuance of 4 Seam workings in 1958 and again in 1980, after reopening in 1972. With room and pillar mining continuing in the 3 Seam, the majority of the 4 Seam reserves have been undermined. The mine began operation using track mounted conventional equipment. Off-track conventional equipment was next used, and in 1957 continuous miners were introduced. Since this tie, continuous miners on room and pillar work have been exclusively used with the exception of a brief shortwall trial in the 4 Seam in 1975. By mid 1982, 3 Seam mining will have been completed, leaving an estimated 42 million in place tons of 4 and 5 Seam coal as the focus of mining efforts. Plans for the subsequent reopening of the 4 and 5 Seam workings have been scheduled for June of 1981. With the resumption of mining, management is faced with solving the roof support problems caused by both the inherent physical conditions and undermining.

Jan 1, 1981

By Daniel W. H. Su

Surface subsidence induced by multiple-panel coal extraction was calculated with finite element stress analysis. The use of nonlinear material behavior and GAP elements, which provide a realistic representation of shearing along existing planes of weakness, allows the finite element program to accurately reproduce observed subsidence profiles. A reduction factor of 1/6 is applied to the measured rock strength and modulus for use in the finite element model. The models satisfactorily predict a significant change in maximum subsidence and subsidence profile associated with an increase from subcritical to near critical panel width. Modeled shearing along planes of weakness is in good agreement with available time domain reflectometry field observations and is demon¬strated to have a very profound effect on the maximum subsidence and the shape of the subsidence profile. When both material nonlinearity and planes of weakness are incorporated, the finite element model appears to possess great potential for accurately predicting surface subsidence and subsurface strata deformation in environments where little subsidence information is available.

Jan 1, 1990

By Dave Forrester

Mining subsidence over shallow abandoned coal mine workings is unfortunately not an uncommon experience in the coalfields of North America and there is a significant knowledge and literature base addressing the phenomenon and related issues. From time to time, however, a case history arises which is outside the more routine occurrence. This paper addresses one such case and presents an overview of a subsidence Event above abandoned coal workings, which badly damaged a two-story High School building. The subsidence at the Cape Breton & Victoria Regional School Board (CBVRSB)'s MacDonald High School in Dominion, N.S., Canada on October 30, 2002 led to a detailed investigation. It was concluded that the ground movement and associated building damage had been caused by mining subsidence in underlying old underground coal mine workings of the 1890s, only 150 ft deep at the School. The Event was not isolated and a similar but smaller event happened nearby a few months later. The paper describes the events and summarizes the subsequent investigations and findings. The 17-year old High School building was eventually demolished.

Jan 1, 2004

By Eric G. Zahl

Researchers at the Spokane Research Laboratory of the National institute for Occupational Safety and health are evaluating stress and displacement measurements in a longwall coal mine. The objective is to determine the best indicators of coal bump hazards during operations so that mine foremen and technical stall can make more informed intervention decisions to protect miners from coal bumps. Instruments were clustered in two panels, a yield pillar, and the immediate roof and floor of a two-entry longwall coal mine. Data were gathered continuously from a variety of instruments as mining proceeded toward and past the instrument cluster. Researchers and the mine's technical staff evaluated these data with respect to coal bumps and bump mechanisms. Selected graphs were then presented to mine foremen on a periodic basis to test their usefulness in identifying hazards. Of particular interest was the use of horizontal stress data from the immediate roof. To measure changes in horizontal stress, a new technique was devel¬oped for installing a grouted biaxial stressmeter in the roof. An evaluation of the development of this stress monitoring system in producing data beneficial to mine foremen is presented.

Jan 1, 2000

By Gexin Sun

This paper presents the physical modelling results of subsurface fracture development associated with longwall mining operations and an application of image processing techniques to interpretion of the results. Physical modelling results have been obtained by employing a large sand and plaster model loaded purely by gravity as a means of fracturing the subsurface strata above the longwall excavation. The results have shown fracture development and crack propagation as a longwall face advances and demonstrated that the strength of stratified rocks, the presence and position of a weak band-, and the extraction thickness, have significant effects upon the overall fracture patterns above the excavation. Binary images of fracture patterns were scanned from the black and white photographs of the tested models using an image analyser coupled to a video camera. These images were manipulated by a custom written C program which allows the images to be processed in both vertical and horizontal direction. The images were filtered to quantitatively differentiate between vertical and horizontal fracture intensities. The vertical fracture intensity is particularly important as vertical fractures are considered to provide the main avenues for surface and subsurface water inflow into the excavation. The use of the image analysis techniques has shown a promising improvement in image enhancement and in model results interpretation in a quantitative manner. The numerical nature of the image analysis results will allow further statistical comparison with other modelling techniques to be undertaken and significantly increase the scope for use of the modelling technique results.

Jan 1, 1992

By Z. C. Song

[THIS PAPER WAS TRANSLATED FROM CHINESE TO ENGLISH BY S. S. PENG, WEST VIRGINIA UNIVERSITY] Immediately after coal extraction, the pressure that causes the movement of the surrounding strata is called mine pressure. Through the strata movement, certain features such as supports taking load arise. This is called "manifestation of mine pressure". The existence of mine pressure is ab¬solute whereas its manifestation is relative and conditional. The visible movement of the surrounding strata occurs only when the applied pressure exceeds the plastic breaking strength. Me support begins to take load only when it offers resistance to the strata movement. The key to investigating mine pressure and its control hinges on understanding the rules and conditions for the manifestation of mine pressure. Since the face moves continuously, the mine pressure and its manifestations are also constantly changing. 'Therefore, it should not only emphasize to obtain its instantaneous magnitude, but more importantly the rules of development changes and their relations to the movement of overlying strata. Once this is resolved, one can estimate the movement of the overlying strata through mani¬festation of mine pressure and predict the time and magnitude of incoming roof weighting. Consequently the location and timing of rib excavation can be correctly selected and thus solve several major problems in the design of mining operation.

Jan 1, 1982

By Robert L. Schmidt

The support of underground openings by water is a natural phenomenon. Surface sinkholes, such as those that occur with some frequency in Florida, are attributed to a lowering of the water table resulting in the draining of existing limestone cavities. This withdraw the natural support and causes the surface subsidence. The role of water as a ground support medium was demonstrated in a mining situation during Bureau of Mines research on borehole mining of phosphate in St. Johns County, Florida. The borehole mining tool (BHT) incorporates a water jet nozzle and slurry eduotor in a single down- hole tool. The tool is lowered through a bore- hole into the ore zone, and an underground cavity is eroded by the motion of the water jet with the slurry simultaneously pumped to the surface. In addition to phosphate, the system has been successfully used in coal, oil sands, and uranium. The Florida phosphate ore is located at a depth of approximately 250 ft in strata that produce high water inflows. These factors preclude extraction by conventional methods, either surface or underground, but they present an ideal setting for borehole mining. Previous borehole mining research had led the researchers to believe that the system would only be effective in a void cavity, that is, a cavity where the water level is maintained below the water jet nozzle, so that the water does not impede the action of the let. It was soon discovered, however, that the void cavity presented ground control problems. The overlying strata started to cave soon after the support provided by the water was removed. This was an unacceptable situation as it adulterated the ore and threatened surface subsidence. Further tests wherein the size of the cavity -as reduced by cutting only a 30° arc also resulted in caving. A new concept, air shielding, was then introduced and tested. With this system, the water jet cutter was surrounded with a shroud of compressed air, thereby gaining the advantages of cutting in air while retaining the roof support afforded by a water-filled cavity. This arrangement proved to be highly successful. The air-shrouded jet was able to cut a cavity radius of about 18 ft, and the system production was 35 tph, which compared favorably to the production previously attained in void cavities. The borehole phosphate experience proves the efficacy of remote mining in a water filled opening. This system neutralises the hazards of heavy ground, and may, as in the case of the phosphate deposits, be the only viable alternative. It opens up the possibility of application in a wide range of deposits not only those amenable to hydraulic mining. Remote mechanical System might be developed using present robotics technology and then operated in water-filled openings.

Jan 1, 1986

By Thomas Barczak

Hydraulic cylinders are used in several roof support systems, such as longwall shields and mobile roof supports, to provide critical ground control Many state-of-the-art hydraulic support system operate at pressures as high as 7,000 psi to provide the necessary support capacities Pressure in the upper stages of multi-stage cylinders can be intensified by a factor of 2 or 3 providing pressures of 20,000 psi or greater. A proper understanding of the operation of these high pressure systems is necessary to safely maintain and repair these support systems. Likewise, the performmce characteristics need to be fully understood to evaluate the impact of design parameters on the capability of the support to maintain effective ground control This paper examines the basic operating principles of state-of-the- art hydraulic cylinders and discusses relative issues pertaining to. (1) setting loads, (2) support stiffness, (3) yielding behavior, (4) errors in assessing support loading, and (5) hydraulic failure mechanisms and how to detect them

Jan 1, 1998

By Greg Hendon

Longwall developments in the UK have historically consisted of single entry gate roads. Adjacent developments were separated from existing panels by large barrier pillars (designed of sufficient width to get away from the longwall abutments of the previous panel) or by small barriers driven in the shadow, or de-stressed zone, of the previous panel. Some 2nd panel tailgates were also driven skin to skin leaving no coal barrier between the newly driven entry and the heavily supported existing gateroad. With the developement and wide acceptance of fully bolted entries and the pressure to reduce production costs, alternatives to single entry drivage, particularly yield pillar developments, were examined. Through the Rock Mechanics Branch of British Coal, a cooperative study was begun with Jim Walter Resources, Inc., USA, (JWR) to look at the yield pillar alternative in detail. This study was to determine the feasibility of utilizing yield pillars in the UK and to determine, through monitoring, the possibility of reducing stable pillar widths at JWR. The study has included extensive monitoring of the yield-stable-yield pillar system at JWR No. 7 Mine and an underground trial of a two entry yield pillar test area at Welbeck Colliery in the UK. This paper describes results from the JWR study and the subsequent results of the first advancing yield pillar development in the UK at Welbeck Colliery.

Jan 1, 1995