Search Documents

By Andre Vervoort

The roof in coal room and pillar panels is normally stratified and can be thought of as beams or plates supported by the pillar sides in the roadways and by pillar corners in the intersections Underground measurements showed the effect of the face advance on the additional total movement of the roof skin and on the relative movement between various layers in the roof. The latter consists of the opening of bedding planes and of the lateral sliding of layers over one another. Both phenomena increase locally the axial load along full column anchors. Four models have been used to come to a better understanding of the roof behavior: a beam either clamped above the pillar side or laying on the pillar sides and a three-dimensional boundary clement model with and without bedding planes. The shape ref the curvature of the roof deflection is host approached by a clamped beam: the other models overestimate the movement at the sides. The largest roof deflection for a given Young's modulus is estimated by the model incorporating bedding planes. This model estimates that the bed separation occurs close to the face (within the first meter) and within 0.2 m of the sidewalk. In some simulations, openings are even recorded just ahead of the face. Further underground measurements should focus on these findings, as the effectiveness of the support is directly related to the amount of bed separation and sliding, which have occurred prior to the support installation and which still cart occur abler installation.

Jan 1, 2000

By Vladimir Adamek

Two existing predictive methods were chosen for evaluation; an influence function (Gals Theory) and a profile function (hyperbolic). These were applied to several field measured subsidence pro¬files over United States coal mines. The effect of homogeneous versus non-homogeneous overburden on surface subsidence is demonstrated and the utilization of Bals Theory as a subsidence predictive method for both types of overburden is examined. The major factor affecting subsidence profile characteristics is the migration of the inflection point toward the centerline of the longwall panel. A computer program was written to aid in the analysis.

Jan 1, 1981

By Liang Yinhuai

The hydraulic-stowing mining method is most effective for mining thick coal seams. It is superior to the sliced cover-caving and artificial mining method and the fully mechanized sublevel-caving mining method for the following reasons - a much higher recovery rate is achieved, there is much less surface subsidence and roof pressure, there is no hidden danger of gob fire, and much less methane emission and coal dust problems, etc.. However, its superiority is overshadowed by its backward stowing technique which makes mechanisation of mining and stowing difficult, causes bleed water interference to production and to the environment and is uneconomic because of the high cost of stowing material. These disadvantages limited its application to coal seams that are difficult and not suitable to be mined by other mining methods. The remedy is in reforming it thoroughly to permit mining of otherwise unminable seams and this paper presents the reformation.

Jan 1, 1992

By J. Nielen van der Merwe

The main objective of the research described in the paper was to determine the causes of falls of roof in South African coal mines. The south African Colliery Manager's Association and the members of the South African National Institute of Rock Engineering (SANIRE) who are employed by coal mines lent full support to the work. Fifteen major roof falls were investigated in detail and their causes established. This data was supplemented by mapping a large number of roof falls on four coal mines in less detail. The total number of recorded roof falls was 182. The data bank simulated the data bank of roof falls that resulted in fatalities in terms of the total number of falls recorded and the thickness distribution of the collapses. It was found that the causes of the falls differed for different thickness ranges of roof falls, The thin falls, classified as "Skin falls", which accounted for approximately 70% of all fatalities, were predominantly caused by ineffective joint support and excessive bolt spacing. Ineffective joint support was found to be a dominant cause of roof falls for all thickness ranges, while the influence of excessive bolt spacing diminished with increasing fall thickness. However, it remained a significant cause of roof falls even for the major falls. Burnt coal, dykes, bad mining practice, weathering and inferior materials were found to be minor causes, but nonetheless contributed to the falls. Horizontal stress was a minor cause, with increasing contribution for thicker falls. It was also found that the indicators of horizontal stress coincided with areas of reduced roof rock strength. In general, roof falls occurred in areas where the roof rock was found to be less competent in terms of rock mass rating systems. It was concluded that the Coal Mine Roof Rating (CMRR) system developed by NIOSH in the USA held promise for application in South Africa and should be investigated further.

Jan 1, 2001

By K. Y. Haramy

Deep coal mines with strong roof and floor strata frequently encounter face and rib bursts. The burst problem becomes more severe with increased depth. While the exact causes of bursts are often difficult to determine, localized high stress zones are common to their occurrence. This Bureau of Mines report describes a study at a mine using longwall systems that experienced both face and floor bursts. The study correlates shield loading, entry closure, and forward abutment pressure increases to observed burst occurrences. The results indicate that strong roof strata that overhang behind the longwall supports create additional abutment stress. When caving lags behind the face and the abutment zone does not advance ahead of the face during mining, stresses on the face may increase to a critical level, resulting in a burst. The critical level occurs when the stress in the abutment zone exceeds the ability of the coal and/or adjacent strata to store strain energy. Caving characteristics may be improved by inducing fractures in the roof or by providing sufficient support resistance to shear the roof. Data analysis of a major burst indicated a dramatic increase in floor heave, with a maximum occurring 80 to 100 ft inby the face, and a lag in the cave line behind the face supports. Analysis of the effects of caving characteristics and floor heave on burst occurrences is presented.

Jan 1, 1987

By E. Bauer

During 1987 and 1988, the Eighty Four Complex Mine of BethEnergy Mines, Inc. used the open entry longwall recovery method to recover one partial and three complete longwall faces. Various cement- concrete supports were utilized to support the open recovery entry until the approaching longwall face cut into this entry. This recovery method and the supports used were studied by the mine personnel and the Bureau of Mines. This paper discusses the findings, results and conclusions of that study.

Jan 1, 1988

By Keith D. Koper, Kris L. Pankow, Derrick J. A. Chambers, Michael K. McCarter

"In a mining environment, high quality seismic event catalogs are often useful in interpreting local stress states and identifying areas with elevated ground control risk. Installation, operation, and maintenance of local/in-mine seismic networks, however, may be prohibitively expensive, and mine operators may not anticipate the need for seismic data until unusual mining conditions arise. If regional, generally public, seismic instrumentation could be used to reproduce the results generated by local/in-mine instrumentation to an acceptable degree of fidelity, it would be a valuable and inexpensive tool for mine planners and ground control engineers.In this study we apply subspace detection—a non-traditional seismic event detection technique—to data from a sparse, regional network. The process is employed to identify mining induced seismicity (MIS) from an underground coal district. The results are compared to a seismic event catalog produced by a local seismic array operating within the permit boundaries. Additionally, we analyze the performance of two different stations of the same sparse, regional network in identifying blasts at a surface coal mine for which we have a detailed blasting log. In both cases data from stations between 10 and 60 km away from mining activity are used. We also explore the trade-offs between the number of detections and the number of false positives, which is influenced heavily by detection thresholds and the number of stations used in the process.For the surface mine we are able to identify more than 90% of the production blasts documented in the blasting log. We also find that the detected blasts from each of the four active pits produce waveforms similar to one another. The results are not dependent on source-receiver distance, and by requiring detections to occur on both stations the number of sure false positives is reduced to zero. In the underground mining district we identify between 30% and 75% of the events detected by the local array, depending on the acceptable number of false positives and the source-receiver distance. We also find many events that were missed by the local array, showing that regional subspace detection can usefully augment traditional local catalogs. Moreover, subspace detection can provide an estimate on event location and classification using data from as little as one seismic station."

Jan 1, 2015

By Jim Sandford

The South Bulga Colliery longwall operation, owned and operated by Cyprus Coal Australia. Oakbridge Pty. Ltd., and located near Singleton, NSW, is currently operating under an average 80-ft-thick (24-nt) sandstone unit residing immediately above the coal seam, resulting in sudden and severe face weightings. To date, nine severe weightings have occurred at the property (within Panels 3, 4. and 5), three of which resulted in face closures accompanied by significant equipment damage and several weeks of downtime. The remaining six events nearly resulted in face closures, incurring single-pass vertical convergence of up to 8 in (200 mm) along the pan line. In an effort to mitigate and/or eliminate the occurrence of these severe weighting events, mine management has established an in-house program to immediately address the geotechnical and operational mechanisms underlying rapid weightings, as well as specific measures to mitigate these events on future panels. In support of this in-house effort. NSA Engineering Pty. Ltd., is assisting the engineering staff at South Bulga in developing a more aggressive face monitoring program. The aim of this program is to provide weighting occurrence predictions sufficiently ahead of time to ensure that operational controls are optimized prior to attempting to mine through potential weighting areas. This paper reviews the occurrence of weightings to date at the South Bulga Colliery as well as the latest developments in shield monitoring technologies to forecast these events in near-real time.

Jan 1, 1999

By P. Tsang

In order to deal with ground control problems such as roof falls, floor heaves and pillar failures in underground coal mines, a new pillar design method based on the "yield pillar" concept is proposed. Using the finite element model simulation, the functions and mechanisms of the "yield pillar" are studied. The important variables that affect the stability of longwall entry-pillar system are identified. To simplify the geological and mining conditions, a new pillar design method classifies the in-situ roof and floor conditions into four categories: 1) strong roof and strong floor, 2) strong roof and weak floor, 3) weak roof and strong floor, and 4) weak roof and weak floor conditions. The design formulae are derived based on the finite element model simulation, stability study and nonlinear regression analysis. The finite element models used consider the plastic failure properties and time-dependent behaviors of rock. To better organize the finite element model simulation, the orthogonal experiment design is used to arrange the finite element models and proved to be very effective. An application example is used to illustrate the basic design procedures involved in the new pillar design method.

Jan 1, 1993

By K. Hanna

This manuscript describes an extensive ground control study at the Inland Steel No. 2 Mine near McLeansboro, IL, conducted by the U.S. Department of the Interior's Bureau of Mines (USEM) in cooperation with Inland Steel Coal Co. The mine experiences severe ground control problem primarily due to high horizontal stress, particularly at entry intersections. Mine experience has shown that reorienting mine entries, modifying the bolting pattern, and altering the mining sequence are effective in reducing the severity of roof falls and out-of-seam dilution. However, the frequency of roof falls has not been significantly reduced. This research project was designed to provide a thorough explanation of the intersection failure mechanism through combined analyses of company in-mine experience and Bureau field measurements. Stresses and deformations were monitored in a four-way intersection during all stages of development and were related to site observations and theoretical analyses. The results of the combined analyses indicate that high horizontal stress is the predominant factor contributing to intersection roof falls in the Inland Steel No. 2 Mine. The horizontal stress induces shear zones to form along the outby 1 ribs, causing the immediate roof layer to detach 1 and behave as a cantilever beam oriented diagonally across the intersection and parallel to i the maximum horizontal principal stress. As the shear zone progresses upward, roof layers successively detach and fail, forming a dome-type roof fall.

Jan 1, 1986

By Fred Leighton

Outbursts, or the sudden and sometimes catastrophic expulsion of coal and gas into the working area of a coal mine, are a little understood and growing problem. The AE/MS (Acoustic Emission/Microseismic), or rock talk, activity prior to and associated with several outbursts has been recorded using ultrasonic and micro- seismic equipment and has been analyzed by the Bureau of Mines. Analysis of these data indicates that outbursts are comprised of several failures in rapid succession and that anomalous AE/MS data suitable for providing failure warning are generated 15 to 45 minutes prior to the failure. This paper discusses the techniques for recording and analyzing these data and presents sane case histories.

Jan 1, 1982

By Deren Zhu

Based on the results of field observation and physical model analyses, a computer simulation method, FEAEBP, has been developed for simulating the breakage of the main roof by considering it as a Kirchhoff plate on Winkler elastic foundation. By this method various parameters of rock property, different boundary conditions of the working face and the initiation, development and results of the breaking process of the main roof with different geometric dimensions can be effectively simulated. Since the main and immediate roofs, and the coal seams are treated as an integrated mechanical system, the interaction among them can be studied in detail.

Jan 1, 1988

By Jinsheng Chen

For underground openings, many factors can cause roof failure and thus roof falls. The most common factors related to Mother Nature are weak roof lithology, geological structures, and an abnormal in-situ stress field. Theoretically, any underground opening can be successfully supported under any geological and mining conditions if the opening width is limited and the roof supporting system is well designed. However, roof control cost must be taken into account. In practice, to minimize the roof control cost, different roof control plans have to be considered to take care of the uncertainty or variation in geological and mining conditions. For most underground mines, it is unsafe or economically unrealistic to use one fixed roof control plan for the entire mine. Therefore, local, abnormal geological and mining conditions must be identified and a site- or area-specific roof control plan must be employed. This study tries to identify the major factors that have significant impact on entry roof stability by analyzing the historical roof fall data at Rofomex mine. Finally, the appropriate roof control plans or roof bolting systems for different geological and mining conditions are recommended.

Jan 1, 2011

By Guang Ping Cui

In this paper the imminent relationship between rock burst and its phenomenon with normal rock pressure and its appearance, as well as the factors of one changing into another have been analyzed. Based on this, the necessary and sufficient appearing factors of rock bursts have been put forward, and the term "burst pressure" has been defined. According to the statistics data of tremendous rock bursts which appear in collieries in Hunan Province, the futures of high frequency, great strength and shallow depth of the beginning burst have been found. There ere some special structures in the coal seams, which are closely related with the burst phenomenon. A hypothesis of "star structure" has been suggested for the appearing mechanism of bursts. Inside and around this star structure the distribution rule of burst pressure and rock strength has been researched depending upon the theory of the limited stress field. A new description of the appearing causes of bursts has been raised.

Jan 1, 1984

By André Vervoort

To learn more about the fundamental roof behaviour in South African coal mines, accurate underground measurements of roof deflection were conducted in bord and pillar panels during development and pillar extraction. To conduct these measurements a survey levelling technique was adapted. The overall system reading accuracy was established as being within 0,4 mm on a 15 m sighting distance. The underground sites were modelled and, for a roadway development, similar symmetrical curvatures were calculated by a linear elastic model, as were measured underground. In a pillar extraction panel, a significant amount of bed separation was measured and the roof underwent an a-symmetric movement due to the close presence of the mined out area at one side of the roadway.

Jan 1, 1992

By Douglas Morrison

By applying modern 3D numerical modelling techniques to the analysis of a pillar cascade failure in a room and pillar mine, it has been possible to simulate the collapse and develop an understanding of the role of low rock strength areas within the mine. The cascade collapse occurred in a normal strength area but would not have occurred without the influence of a low strength rockmass in one section of the mine. The numerical analysis made it possible to develop a realistic assessment of the residual pillar strength. With the introduction of regular empirical pillar performance assessments, critical pillars or groups of pillars can now be identified proactively. This has led to an aggressive extraction ratio of 90% that manages pillar failure, avoids pillar and roof collapse and prevents surface subsidence. Since the mine also has significant waste products, the use of backfill for ground support has made it possible to significantly improve the performance of strategically located pillars, and so achieve even higher extraction ratios.

Jan 1, 2003

By Nikolaos Polysos

To drive and utilise gate roads economically requires accurate planning and risk assessment considering the variable geomechanical requirements. The geomechanical part of roadway planning is secured by geotechnical investigations of drill cores and geophysical borehole logging. The rock specific parameters determined in this way allow a statement about the quality (defomtation and strength characteristics) of the rock that has to be cut across. They set up the basis for a standardised rock assessment. Combined with the prevailing rock mechanical situation, technical boundary conditions for advance and support techniques can be identified already in the planning phase. Detailed geotechnical investigations prior to the planning and driving of roadways can lead to a technically and economically optimised roof support system. Geotechnical core logging and a standardised assessment scheme based on the data acquired will be introduced. Geophysical borehole logging methods provide additional physical data. Different methods and their validity, which may lead to a further improvement of the planning reliability, will also be presented. The geomechanical information gained and their relevance fir the planning will he illustrated. Keywords: rock classification, geotechnical rock parameters. geophysical well logs. support planning

Jan 1, 2002

The formation of tension cracks in slopes is well known. Analytical studies require the determination of a critical slip surface for any slope and, in doing so, it is necessary to consider an appropriate tension crack. A general yet simple approach is proposed for identifying the critical slope failure surfaces associated with critical tension cracks. The minimum factor of safety consequently reflects both safety against shear sliding and tensile failure. In general, the critical slope failure surface for a slope determined in this way differs from that which is obtained without optimizing the position and depth of the tension crack. In particular situations, the difference is significant.

Jan 1, 1989

By Jennifer Riefenberg

Underground coal mines often experience ground control problems related to weak floor. Developing a methodology for rating floor quality can aid in understanding and delineating ground hazards. U.S. Bureau of Mines researchers are currently exploring methods for generating ground control hazard potential maps. One component of hazard potential in floor-heave-prone mines is delineating floor quality and its correlation with failure. Although field exposures are limited, significant information on the roof and floor quality can be gained through analysis of existing drill core data. Drill core data and roof and floor exposures were analyzed for quality. Laboratory tests were run on 50 core samples to evaluate, compressive and tensile strengths of various roof and floor lithologies. Extensive geologic and lithologic examinations of the cores and samples were also completed. Results of this work involve the formation of a preliminary quality rating for coal mine floor using a modified Coal Mime Roof Rating (CMRR).

Jan 1, 1995

By D. F. Howarth

Two innovative ground reinforcement products have been developed for use in the mining industry. One of these products is a high strength polyethylene (HOPE) bar for use as a rib bolt in underground coal mining and as a corrosion proof tendon in open pit mines. The other product is a cable bolt (Ultrastrand) which demonstrates enhanced load transfer and is available in continuous lengths. Ultrastrand's exceptional in¬situ performance and versatility makes it ideal for mechanised installation in both underground and surface mining operations. Details of these products are presented and results from labortaory and field trials are discussed.

Jan 1, 1992