Search Documents

By Min Chen, Lei Xu, Weijun Huang, Shuai Zhang

For the purpose of extending the service life of MgO-C bricks used as linings of vanadium-extraction converters, the effect of Fe addition on properties of MgO-C bricks was investigated. The results showed the addition of Fe could effectively improve the sinterability of the oxidized layer of the MgO-C refractory at 1400°C due to the effect of FeO (formed by oxidation of Fe) on formation of MgO-FeOss and modification of the microstructure, and excellent corrosion resistance against vanadium containing slag was also obtained due to the increase of compactness of the oxidized layer and concentration of FeO in the oxidized layer. Consequently, it is considered that MgO-C brick by introducing the new phase of Fe is a favorable substitute of MgO-C refractory to be used as linings of vanadium-extraction converters.

Jan 1, 2015

By John J. Dunkley

Recent years have seen the increased use of hydrometallurgy in the smelting and refining of metals. However this is often used as a final refining step, following an initial pyrometallurgical smelting process. Huge amounts of material are produced as melts which have to be cast, comminuted, and taken up into solution or leached. A common method is to granulate the melt and then grind it. In the case of metallic melts this can be difficult or unfeasible due to the ductility of the granulated particles. Water atomisation is capable of replacing the granulation and grinding stages with a single process step that can process in excess of 30t/hour of melt into particles as fine as 50 microns. Applications in operation in Co, Cu, Ni, Ag, Au, Pt and Rh refining are discussed together with potential applications in copper smelting.

Jan 1, 2003

By J. P. Evans

The modem copper smelter today utilizes tonnage oxygen for smelting concentrates, generating a high strength S02 off-gas leaving the smelter vessel. This gas stream, which also contains any unreacted oxygen, plus C02, N2 and H20, also carries with it the volatilized portion of heavy metals in the feed, plus partly oxidized sulfide concentrates. The time/temperature history and subsequent treatment of this off-gas stream emerging from the smelting furnace exit up to the acid plant can influence the partitioning and segregation of heavy metals in the off-gas circuit. Depending on this history, the type and characteristics of the chemical and physical reactions which. occur in the gas handling system can be influenced. This fact can also be used as a tool to adjust the separation of copper from heavy metals. In this paper, the impact of different time/temperature histories of the gas, due to different furnace geometries .and design, on the subsequent formation and characteristics of the smelter dust is examined. Based on the available data, several case histories drawn from examples using both bath and flash smelting technologies are analyzed from this perspective.

Jan 1, 1992

By J. P. Evans

The modem 'copper smelter today utilizes tonnage oxygen for smelting concentrates. ,generating a high strength S02 off-gas leaving the smelter vessel. This gas stream. which also contains any unreacted oxygen, plus CO2; N2 and H20. also carries with it the volatilized portion of heavy metals in the feed, plus partly oxidized sulfide concentrates, The time/temperature history and subsequent treatment of this off-gas stream emerging from the smelting furnace exit up to the acid plant can influence the partitioning and segregation of heavy metals, in the off-gas circuit. Depending on this history. the type and characteristics of the chemical and physical reactions which occur in the gas handling system 'can be influenced. This fact can also be used as a tool to adjust the separation of copper from heavy metals. In this paper, the impact of different time/temperature histories of the gas, due to different furnace geometries and design. on the subsequent formation and characteristics of the smelter dust is examined. Based on the available data. several case histories drawn from examples using both bath and flash smelting technologies are analyzed from this perspective.

Jan 1, 1992

By P. S. Seryogin

R & D works supported by industrial-scale tests, which were carried out by joint efforts of the OAO Gipronickel Institute and MMC ?Kola? engineers, have accomplished with the production of 90?95% metallized nickel powder in tube furnaces (NPTF), with its ?active fraction? (AF) to be further used for decopperization of nickel electrolyte by cementation. Consistently positive results obtained in the course of the lab and industrial experiments have allowed the Severonickel Combine management to effectively replace all activated nickel powder (ANP), which was then employed for cementation, with the AF, having activity over 80%, and eventually shut down the entire operation of gaseous reduction. Ever since the developed technology has been implemented, its annual economic effect exceeds 2 ml. dollars.

Jan 1, 2006

By Zhang Hengzhong

Based on thermodynamics of surfaces and a proposed two-dimensional state equation for surfaces, the relationship between the surface tension (Y) of a solution and the activity (a1) of its component (i) was derived: (1/Y)r2-.¬E (ai/Yl) The derived equation was verified with reported experimental data of water-alcohol systems and water-acetone system, the calculated results showed astonishing coincidence with experimental. Applications of the equation to the five matte systems Cu2S-FeS, Ni3S2-FeS, FeS-PbS, Cu2S-PbS and FeS-Cu22S-PbS also demonstrated that at given matte compositions the calculated surface tensions agreed with experimental fairy well.

Jan 1, 1993

By T. Shoji

"The human history is characterized by social development based on mineral and energy resources, and many conflicts to take the resources by power. This is shown by not only world wars but also many local conflicts as well as international supremacy.IntroductionThe world population after B. C. 10000, which is summarized in several papers, is approximated by four straight lines on a semilogarithmic diagram as shown in Figure 1 [l]. The annual rates of increasing are 0.0041, 0.071, 0.53, and 1.85 % from the old and young periods. The boundaries among four periods are approximately B. C. 4600, AD. 1670, and 1930. The start of the second period seems to correspond to the beginning of agriculture and cattle breeding. Precisely speaking, the usage of natural energy resources such as woods and domestic animals already began, but is inferred to have become common after the age. The third and fourth periods are characterized by the common usage of coal and oil, respectivety. Not only energy resources but also mineral resources including gold, copper, iron and others are also important for the human history.Mineral and energy resources have supported the development of the .human civilization, and have caused many conflicts because of this reason. Every day newspapers report conflicts, such as Chechnya, East Timor and Ache. We can easily point out the facts that the conflicts closely relate to mineral and energy resources. Groznyj, Capital of Chechnya, is located on the western margin of Caspian oil field. Many mineral deposits occur in Kavkaz Mountains running south of Chechnya. Subsea oil fields occur in Timor Gap located between East Timor and Australia. Ache is also one of oil fields in Indonesia. It is very difficult to state present conflicts independently of a political view of point. For this reason let us try to historically review the relation between mineral and energy resources and international domination and conflicts [2] based on many papers [3]."

Jan 1, 2000

By James D. Navratil

Advances in hydrometallurgy require the introduction of new separation and purification processes, but they can be complex, costly and energy intensive. Chromatographic processes have low energy requirements and possess very high separation efficiencies. However, they have not yet made the great industrial impact that might be expected from their benefits. The large-scale and difficult separation of rare earths would greatly benefit from an improved continuous chromatographic operational device. Truly continuous, multicomponent chromatographic separations may be achieved by means of the continuous annular chromatograph. Work has been Initiated at The University of New South Wales involving the improvement and development of such equipment for the separation and purification of rare earths.

Jan 1, 1990

By A. Buzaianu, P. Motoiu, G. Popescu, C. A. Popescu, I. Rusu, A. F. Olteanu

"In recent years, the recycling magnesium metallurgy has developed new types of alloys, some of which exhibiting special electrochemical characteristics. Their application has found a fertile field in the energy conversion technologies. The paper introduces some technologic data on the recycling of aeronautical parts and scrap materials generated from the disassembling of magnesium alloy components, attempting to also solve the recycling of magnesium painted parts. The approach is meant to establish a superior quality method for recycling discarded parts or the excess of re-melting material in order to reduce environmental impact and costs. Magnesium-base alloys used as anodic materials are characterized by a high uniformity of the structural properties as well as by superior electrochemical performances, as compared to the ""classically"" used materials: Zn, Pb, etc. In nonconventional applications of magnesium alloys used as sacrificial anodes working in seawater, special alloying elements contribute to improving anodic processes. The influence of these alloying elements on magnesium sacrificial anodes was studied. It was found that the use of recycled materials in anode manufacture could reduce the Mg alloy cost by as much as up to 75% of the cost for virgin material, including the costs for the entire sequence of collection and transportation from a molding factory to a refinery, re-melting and composition adjustment.1. IntroductionMagnesium alloys are valuable materials because they exhibit low density, good forming and machining qualities, particular electrochemical properties and have a high recycling potential. There exists a false idea about the high costs of the use of magnesium alloys, partly justified by the lack of secondary materials suppliers and the insufficient knowhow in the diverse user industries to provide for an efficient substitution of conventional magnesium alloys for multipurpose applications. These circumstances have lately spurred the magnesium industry to develop new alloys and coatings and to improve processing techniques [1]. As a result, magnesium supply has greatly expanded and so have the research and development efforts to achieve complete recycling of Mg alloys.In consumer markets, magnesium is frequently selected because it helps reduce enery consumption. For example, an equal volume part made of magnesium is 23% the weight of a steel part and 64% the weight of an aluminium part."

Jan 1, 2008

By Okechukwu Anopuo, Gerhard Tober, Petra Maier

"In this study, an investigation on the microstructure of hot rolled steel S355J2+N was conducted to optimize process parameters of complex forming, which combines rolling and bending. The best sets of parameters are worked out based on homogeneous mechanical properties and microstructure within the varied deformation degree with maximum at <p = 1.14 on a 25 mm thick plates. Mechanical properties, especially of heavy plates, are strongly influenced by the local deformation degree, strain rate and temperature. Detailed microstructural analyses showed that the ferrite-pearlite band structure changes near the surface, while maintaining homogeneous microstructure within the deformed work piece. Surface decarburization was also observed and this leads to decrease in hardness. To minimize iron oxide formation which could lead to side cracking, reduction in exposure time to temperature was suggested. On the other hand, temperature reduction below a critical value would risk the accurate forming process.IntroductionThis work presents the preliminary results of research to develop a new complex deformation process of thick steel plates. Complexity is given because the forming process combines rolling to reduce thickness and profiling by bending. The work piece will experience a thickness reduction from 25mm to 8 mm and is double curved. To explain and understand forming of thick plates basics of sheet forming as well as massive forming need to be used. At the moment there is no forming process established to produce double curved plates including reducing thickness in one process step. Technologies nowadays consist of two process steps: flat rolling and pressing in shape. Due to good weldability and formability the final product will be made of steel S355J2+N. This low-carbon steel is well understood and has a low strengthening exponent, which is expected to keep the forming forces down. Reduction of thickness from 25 mm to 8 mm gives furthermore a high deformation degree. Thus, hot forming has to be applied. The determination of process parameters is the main aim of overall research project; temperatures above lOOO°C are expected. Flow curves in literature are given at various temperatures and strain rates [1]. However, experiments with data close to the industrial application are rarely found, especially at low strain rates and high deformation degrees. Pre-test were done by flat rolling, being aware that the influence of bending is eliminated. The microstructure evolution were characterised in relationship to material formability with special attention to grain size change and recrystallization. Representative samples should be selected from specific locations in the deformation zone according to the knowledge about the metal forming process [2]. Due to no further alloying elements in S355, no precipitation hardening is expected to take place during hot forming, which keeps the mechanisms simple and the concentration on the feasibility of the complex forming process is given."

Jan 1, 2012

By Ilona Johnson

United States metals and non-metallic minerals manufacturing consume about 5,000 trillion Btu annually. Various studies estimate that as much as 20 to 50 percent of this energy is lost as excess or waste heat. Recovery of waste heat can conserve energy, reduce operating costs, and lower environmental emissions. It would be valuable to quantify recoverable waste heat sources and identify the barriers that hinder its recovery. This paper provides an overview of waste heat losses specific to high temperature processes in primary metals and minerals manufacturing. It summarizes findings from a broader study conducted for the Department of Energy Industrial Technologies Program; the study evaluates energy losses, recovery practices and opportunities, and R & D needs for waste heat technology development.

Jan 1, 2008

By Grigore Matei

The thermodynamic properties of CuzS-FeS system are important not only in the ease of copper smelting but also in the case of general pyro-metallurgy. However there arc not many reported activity data In this study, activities of FeS and CU2S in the Cu2S-FeS system were calculated using the Darken&apos;s method from the activity data of the Cu2S-FeS-Sb2S3 systems measured by the transportation method at 1050°C. The activities of Cu2S and FeS in the Cu2S-FeS system showed negative deviation from the ideal behaviour and satisfied the relation of the Gibbs-Duhem equation.

Jan 1, 2003

By Fumitaka Tsukihashi

Phase diagrams of the CaO-SiO2-FeOx-MgO, Al2O3 systems arc necessary for the analysis of copper smelting reactions and sintering process of iron ore. The effect of MgO and Al2O3 addition on the liquidus of the phase diagram of the CaO-SiO2-FeOx system at low oxygen partial pressure was observed. The liquid phase area changed bi the addition of MgO and Al2O3 with a changing oxygen partial pressure from 10-8 to 10-3 atm (10-3 to 10 2 Pal at 1573K. The effect of Fe3+ / Fe2+ ratio on the melting mechanism is discussed.

Jan 1, 2003

The merging of flash smelting with spray converting in one single furnace is proposed as a continuous copper making process. The proposed process is expected to produce blister copper, clean slag and gas with high sulfur dioxide concentration. Some high grade matte is an intermediate product recycled within the proposed furnace, spray-atomized and converted. The thermodynamic equilibria of the simultaneous oxidations which take place during copper smelting and converting are discussed in order to establish the gradient of oxygen potential along the furnace required for smooth operation. The proposed process is a dynamic system designed to reach equilibrium only close to the slag skimming end of the furnace. The process feasibility is based on the predesigned significant difference between the rates of converting reactions in a finely dispersed system and the rates of deconverting reactions between immiscible liquid phases of restricted interface area. The converting of small stationary droplets of matte, in a silica saturated system, was studied in the laboratory for extremely short oxidation times (10 to 120 seconds). These experiments led to some interesting observations on reaction mechanisms and kinetic trends. The droplet size and the matte grade affected very strongly the oxidation rate and the proportion of the different products obtained.

Jan 1, 1976

By Henrlk Gripenberg

To solve the environmental and financial problems of the traditional Rotary Salt Furnace process, a new salt-free method for aluminum dross and scrap melting, ALUREC, has been developed by AGA and its partners, Hoogovens Aluminium and MAN GHH. AGA and Hoogovens Aluminium developed the main process concept and jointly carried out trials on pilot plant scale. Owing to excellent results" the partners decided to jointly erect a commercial scale test plant. The order for the design and erection of the furnace went to MAN GHH. The three companies designed the test plant and began operation in the spring of 1994. The results have been excellent and the process is expected to be a technical and commercial success.

Jan 1, 1995

By H. Cepin

Production of non-ferrous metals is still principally performed in shaft and flame fired furnaces. Electric furnaces increase metal recovery, reduce environmental burdens and decrease energy consumption compared to conventional processes. Because non-ferrous metals have low melting and boiling points and aggressive slags design of the furnace, energy input, and slag conductivity and composition are very important. Secondary materials are easily handled in electric furnaces. Since additional amounts of lead, zinc and tin will become available from secondary sources in the future, electric furnaces are expected to replace conventional smelting furnaces. The paper describes technical, electrical, and process designs of electric furnaces peculiar to the reduction of non-ferrous metals. Electric and various thermic furnace processes are compared.

Jan 1, 1990

By Jin Liu

The mechanism and rate of carbon reduction of each of the phases that are formed in the flash flame, i.e. sulfide (matte) and oxysulfide, was investigated. Graphite-slag reduction was conducted for comparison purposes. The objective of these tests was to measure the rate of solid graphite reduction of respectively matte, oxysulfide, slag, and matte+slag mixture at different temperatures. More in particular, these tests were expected to permit understanding and explaining the reduction mechanism of each material by comparing the respective reaction rates, product reaction gas compositions and CO/CO2 ratios, reduced material assays, activation energies, and other relevant parameters. Direct visual inspection of the test crucibles would provide additional information.

Jan 1, 2006

By Hideki Yamamoto

A new technology to convert fluoride gas (C2H2F4 : R-134a) contained in the exhaust gases from semiconductor manufacturing plants and refrigerators directly into a harmless substance have been established, thus, presenting a new concept for the disposal of fluoride gases such as CFCs that are associated with the global warming. Experimental results verify that chemical reactions with metal compounds can take place at substantially lower temperatures of 700- 800K as compared with combustion treatment temperatures of 1200-1500K. The reaction product is mainly metal fluoride, which chemically is a harmless material. Furthermore, this process is compact, easily controlled, safe and has low running costs. This paper deals with a new chemical reaction method for the harmless disposal of gases effecting the global warming.

Jan 1, 2003

By Hideki Yamamoto

A new technology to convert fluoride gas (C2H2F4 ; R-134a) contained in the exhaust gases from semiconductor manufacturing plants and refrigerators directly into a harmless substance have been established, thus, presenting a new concept for the disposal of fluoride gases such as CFCs that are associated with the global warming. Experimental results verify that chemical reactions with metal compounds can take place at substantially lower temperatures of 700- 800K as compared with combustion. treatment temperatures of 1200-1500K. The reaction product is mainly metal fluoride, which chemically is a harmless material. Furthermore, this process is compact, easily controlled, safe and has low running costs. This paper deals with a new chemical reaction method for the harmless disposal of gases effecting the global warming.

Jan 1, 2003

By Walter E. McCulloch

Recent laboratory bench scale and pilot plant metallurgical tests at Mountain States R and D International have demonstrated that some copper ores because of relatively coarse copper sulfide mineralization can be preconcentrated by heavy media separation (HMS). In tests with a copper ore from the AMT Copper Creek project near San Manuel, Arizona, HMS preconcentration rejected about 75 to 80 percent of the feed as a minus 13 mm gravel. The HMS concentrates copper recoveries were about 93 to 95 percent. With the incorporation of HMS preconcentration, significant capital and operating costs savings have been projected for the proposed AMT Copper Creek concentrator. An overview of the HMS preconcentration step development for the AMT Copper Creek project is presented. Also presented are other potential applications of HMS preconcentration for copper ore processing.

Jan 1, 1999