Search Documents

By Reed M. Izatt

SuperLig® materials are capable of individually separating Rh, Pd, and/or Pt in highly purified form (99.95 to 99.99%) from a variety of chloride-based feed streams in a single stage operation. The hydrophillicity and associated kinetics of the supported materials allow for operation at relatively high flow rates of both loading and elution in a packed bed format. Pilot and commercial systems have been operated with Rh, Pd, and/or Pt present in the feed from single digit ppm (mg/l) to tens of g/l. A dual SuperLig® system for one pass Au(CN)2- separation followed by Cu and CN- recovery for CN- recycle has also been tested up to a pilot level,

Jan 1, 1999

By Chikabumi Yamauchi, Mitsuru Tanahashi, Toshiharu Fujisawa

"Thermodynamic properties of impurities in molten silicon are of prime importance in developing economical production methods of solar grade silicon. In the present research work, thermodynamic properties of boron, the most difficult element to remove from molten silicon, were measured by chemical equilibration techniques at 1723 and 1773 K. Activity coefficients and self-interaction parameters of boron in molten silicon were determined by equilibrating the melt with solid BN under controlled nitrogen partial pressures. Interaction parameters between boron and nitrogen in molten silicon were also determined by equilibrating the molten Si-B alloys with solid Si3N4• Based on the data obtained, the stability diagram of the Si-B-N system was established.IntroductionPhotovoltaic power generation using a silicon solar cell is expected to be the most promising energy source, because it is inexhaustible, cleaner and more safety than conventional energy sources, such as thermal or atomic power generation. At present, expensive off-grade silicon for semiconductor (SEG-Si) is used for a solar cell production. However, if a large-scale photovoltaic energy conversion using silicon solar cell comes into wide use in the near future, silicon will be sure to be in short supply for the cell. Therefore, a development of a new large scale process for solar grade silicon (SOG-Si) production is definitely necessary, which can remove contained impurities from silicon.Among the impurities contained in silicon, boron is one of the most difficult ones to remove by a zone melting or an unidirectional solidification, because its segregation coefficient in silicon is close to unity (0.8). In addition, boron behaves as a p-type silicon semiconductor dopant and, therefore, its content in SOG-Si must be severely controlled. Although some attempts to remove boron by various metallurgical methods have been carried out [I -4], quantitative analysis has not been made due to lack in the information on the thermodynamic properties of boron in molten silicon. From this view point, the activity of boron in molten silicon was determined in the present study by chemical equilibration techniques at 1723 and 1773 K."

Jan 1, 1998

By Susanne Pignolet-Brandom

QEM*SEM is an automated scanning electron microscope/computer system that characterizes samples with regard to mineral modal abundances, mineral grain and particle sizes, mineral associations, and particle surface areas. Additional information, based on the classification of particles according to the area percentage of a mineral of interest, can be obtained for samples of particulates. QEM*SEM is capable of analyzing a wide variety of materials although it was originally developed for applications to the minerals industry.

Jan 1, 1988

By M. J. Adam

As part of its research program, the U.S. Bureau of Mines is investigating the partitioning of complex minerals to simpler phases using sulfidation reactions for selective extraction of mineral constituents of value from extraneous elements early in processing schemes. This report describes research in which thermal processing of the complex Ti -bearing mineral ilmenite (FeTiO, ) resulted in partitioning of the valuable Ti metal to the simpler compound rutile (Ti0 ). Samples of ilmenite were blended with elemental S for thermal treatment a2 various temperatures under controlled atmospheres in an effort to dissociate the Fe from the ilmenite complex. Product characterization revealed that the Fe was partitioned from the ilmenite, forming a rim of pyrrhotite/pyri te (FeS/FeS,) on a rutile core. The products were agate milled and then subjected to cursory magnetic and flotation techniques in an attempt to physically separate the partitioned phases. Partitioning results and phase concentration data are reported relative to thermal treatment variables and physical separation techniques.

Jan 1, 1993

By T. H. Courtney, B. R. Murphy

"Nominal room temperature mechanical alloying (MA) has been used to synthesize the high melting temperature NbC and Cu-NbC composites. Elemental powders of Cu and Nb were alloyed in the presence of either graphite or hexane to form nanocrystalline NbC or a Cu-NbC composite. Through control of hot-isostatic-pressing (H/Ping) parameters, we have been able to minimize microstructural coarsening during densijication, and have processed fully dense bulk compacts of both single phase NbC and two-phase Cu-NbC while maintaining a nanocrystalline or near-nanocrystalline structure. These materials generally exhibit high strength and low fracture toughness. However, mechanical properties vary significantly depending upon the Cu content and the method of NbC synthesis (graphite or hexane).INTRODUCTIONMechanical alloying (MA) has been recently used to synthesize a variety of inorganic solids; sulfides (1-2), nitrides (3), borides (4), and carbides (3, 5-8). One advantage of this processing route is that synthesis of fairly high melting temperature materials takes place at what is nominally room temperature. Another advantage is that the structures generated are often nanocrystalline in scale, with attendant interesting properties. The consolidation of these fine structures into near fully dense or fully dense materials while limiting microstructural coarsening is a challenge that has just recently seen limited success (5, 9). We report here on some recent studies of ours dealing with crystallite size and structural analysis of NbC and CuNbC composites consolidated to full density from mechanically alloyed powders. Bulk mechanical properties and their dependence on milling parameters are also presented."

Jan 1, 1994

By Ludwig Hermann

"Phosphorus is required by every cell of living organisms and essential for plant growth. It is a non-renewable resource that must be mined from natural deposits, going gradually into depletion. Abundant secondary resources are available in sewage sludge and meat and bone meal, with the highest exploitable P concentrations in ashes that remain from their widely used combustion with energy recovery. ASH DEC has successfully removed heavy metals and transformed sewage sludge ash into a marketable P fertilizer by application of a thermo-chemical treatment process. Pilot scale investigations in which ash was treated proved that generally heavy metal limits required by fertilizer legislation can be attained. To achieve a high P availability for crops – an essential fertilizer quality feature – was a more challenging R&D task. Our presentation demonstrates the scientific approach and R&D results that lead from assessment of market requirements to licensed products.IntroductionPhosphorus (P) is required by every cell of living organisms. It is one of the major elements for plant nutrition and therefore essential for crop production. P supply in plant nutrition depends entirely on external inputs into soils [1]. This is achieved by P-fertilizers deriving from rock phosphate deposits that are gradually going into depletion. Serious prognoses anticipate that rock phosphate will be the first low running resource in the world [2]. In the EU, last year 2.530 kt of phosphorus (P2O5 in fertilizers) was consumed and only 313 kt (P2O5 in rock phosphate) was mined. Since 2007, rock phosphate prices have increased by 500% because of a tight supply situation [3].For these reasons, P recycling is becoming an increasingly important issue. Suitable secondary raw materials with regard to their high P-content and abundance are sewage sludge and meat and bone meal. In the EU 989 kt P2O5 are accumulated annually in theses materials, of which 632 kt P2O5 are permanently lost to landfills and other forms of disposal. The main reasons for their limited recycling are concerns on heavy metal contents and organic pollutants that may incite health hazards. As an additional shortcoming, the availability of P from these materials to plants is poor and storage and transportation are problematic issues [4, 5]."

Jan 1, 2008

By G. G. Richards

"The slag fuming process has operated for close to 70 years to recover zinc from lead blast furnace slag. The process is normally carried out through the batch treatment of slag by submerged injection of coal and air. Within the bath the coal acts as both a reductant, to reduce Zno to zinc vapour, and a fuel, to maintain bath temperature during the endothermic reduction process. The partition of coal between the slag, combustion and bypass is dependent on factors such as bath depth and injection pressure. The option of continuous fuming has been pursued at the D. Blagoev smelter in Bulgaria using heavy fuel oil as reductant/fuel. There has, however, been little attempt at commercial continuous fuming with coal. This paper presents an analysis of a coal-based continuous slag fuming furnace. The data on the Plovdiv fumer is used as a reference point. Critical design criteria for continuous fuming include the slag feed rate, degree of coal combustion and furnace size. Mathematical modelling analysis suggests that continuous fuming with coal can achieve respectable zinc/coal ratios.IntroductionThe slag fuming process was developed in the early part of this century to recover zinc from non-ferrous smelting slags [1-3]. The majority of installed furnaces were put in place to fume zinc from lead blast furnace slag on a batch basis. In most cases coal is used to effect reduction of zinc oxide, but one furnace uses natural gas [4] and, in a curious twist, a continuous fumer was developed based on fuel oil [5].Given the general nature of blast furnace lead smelting, it is not surprising that slag fuming has remained a batch process, in spite of the advantages that could be gained by moving to continuous fuming. Blast furnaces are usually operated as relatively independent units, and tapping has traditionally been done into ladles. The presence of a crane aisle makes direct coupling of the blast furnace to a slag fumer difficult, especially in a retrofit situation. Furthermore, steady-state blast furnace operation is not easy to achieve. The size of these furnaces and the nature of their feed make it difficult to guarantee constant operation."

Jan 1, 1996

By Debbie Marshall

Nickel and cobalt in lateritic ores can be extracted by either a hydrometallurgical or a pyrometallurgical route. The high-iron limonitic fraction of a deposit is best processed' hydrometallurgically while the magnesium-rich transitional and saprolitic fractions are more suited for pyrometallurgical processing. During hydrometallurgical processing, it may be attractive, for economic reasons, to blend the limonitic component with transitional and saprolitic ores, which contain higher nickel levels. However, blending increases the concentration of magnesium in the feed, leading to increased acid demands. The decision on how much ore to process then becomes an economic one. Ore samples with different magnesium contents were prepared for the leach test program by blending limonitic and transitional ores. The ore samples were slurried in seawater and tested in the Falconbridge Hydrometallurgical Pilot Plant. As expected, acid consumption increased with increasing magnesium content of the ore. For target extractions of 95% nickel and 92% cobalt, the required residual free acid concentration increased from 30 g/L at 1.7% magnesium to 50 g/L at 2.7% magnesium. When the magnesium content was raised to 3.8% and 4.6% in subsequent pilot plant testing, the final free acid requirements did not increase beyond what was observed at 2.7% magnesium. Thus, the cut-off ore composition to maximize nickel units and minimize acid requirements is between 1.7- 2.7% magnesium. Keywords: high pressure acid leaching, laterites, magnesium

Jan 1, 2004

By P .. R. Ammann

A two-stage pyrometallurgical process has been developed for the recovery of copper (and other non-ferrous metals) from copper smelter slags. All types of slags, including highly oxidized, converter-type slags, are cleaned in an electric furnace which employs mechanical mixers to promote magnetite reduction and copper extraction at high rates. In a 10-ton pilot furnace, it has been demonstrated that slags can be cleaned to 0.2-0.3 per cent copper with economically acceptable usage of raw materials and energy; copper is recovered as a high-grade matte. Pilot plant data have been scaled up to a commercial furnace and engineering designs have been made for a furnace to treat 60 tons per hour of slag from a Noranda Reactor and the associated converters. Plans are being formulated for the construction of a prototype slag cleaning furnace.

Jan 1, 1976

By Larry Southwick

This Peirce-Smith Converting Centennial symposium is celebrating the contributions of two men, William Peirce and E.A.C. Smith, in advancing technology allowing the copper industry to realize its full potential. However, theirs is representative of a larger story: New, simpler technology releasing the stranglehold of older, more complicated technology, new developments in vessel configuration and design finding alternate routes around dead ends in operability, advances in technique and concepts removing roadblocks of cycle time and capacity, and overall innovation opening up vast new reserves around the world to those companies willing to embrace those improvements. Our story is also one of personalities, stubborn smeltermen versus the innovators, those inside the industry versus those from outside. It is a story of an initial borrowing from the steel industry, but also Peirce and Smith, from the refining end of the copper business, taking the ideas of Baggaley from Pittsburgh’s steel and airbrake industry, who built on what Hollway, Manhès and David, Douglas, and others had done in smelter tests, further to compete with the previous primacy and closely held expertise of the copper smeltermen in Wales. These advances have been well recorded in photographs taken over the last 150 years. A number were submitted especially for this symposium. Many others were published in the mining and metallurgy press of the times. Several mining schools also retained copies of photos either taken during field trips, or donated to the school by alumni and operating companies. This presentation will provide a selection and discussion from these sources of “converters in action”, describing the various designs, operations and developments depicted. The focus here will be on the first roughly 60 years of copper converter development, from Bessemer’s days at the dawn of this new idea, up to and slightly past the time of initial adoption of Peirce and Smith’s designs.

Jan 1, 2009

By Batric Pesic

Reactions of metallic iron were studied in several different aqueous solution systems: water, medium salt solution used for the growth of T ferrooxidans, ferric iron solution and solution containing T ferrooxidans. Each system was studied under abiotic and biotic conditions in the presence of T ferrooxidans and as a function of pH, particle size of iron powder, temperature, ferrous and ferric iron concentrations. It was found that metallic iron reacts with water differently than does with ferric iron in water. Surprisingly, T ferrooxidans were non-functional in the dissolution of metallic iron. Also, the reactions of metallic iron with pure water were indistinguishable from the reactions with water containing medium salts for bacterial growth. The reactions with ferric iron were also independent of medium culture compounds. The mechanisms of metallic iron reactions with ferric ions are different from the mechanisms of metallic iron reactions with water.

Jan 1, 2001

By John A. Thorpe, Gary R. Maxwell, Kirk M. Schall, Kenneth A. Brunk

"Gold ores containing oxide and some sulfide copper minerals incur significant cost penalties when leached with cyanide, because 4-5 moles of cyanide are consumed for each mole of leached copper. This equates to ~4 kg of NaCN per kg of leached copper. Total cost of excess NaCN consumption plus CN destruction can exceed $4.00 per tonne of ore. AuGMENT Technologies has patents pending on a process that can 1) economically recover 70-80% of the cyanide that is fed to a mill, 2) produce salable copper cathodes, and 3) reduce the need for a cyanide destruction facility. Standard equipment for resin processing and electrowinning are used to recover the cyanide and produce the copper cathodes. Steps have been taken to determine: 1) how to develop the resin kinetics, 2) how much savings are incurred at a mill site, 3) how the novel 'electro-elution' circuit achieves efficient operation.IntroductionWhen gold ores containing nuisance copper are leached with cyanide, a significant cost penalty is incurred because 4-5 moles of cyanide are consumed for each mole of copper that leaches. This is equivalent to the use of -4 kg of NaCN per kg of copper that leaches. The total cost of excess NaCN consumption plus cyanide destruction can exceed $4.00 per tonne of ore.AuGMENT Technologies has a patent pending on a process that can 1) economically recover 70-80% of the cyanide that is fed to a mill, 2) produce salable copper cathodes, and 3) reduce the need for a cyanide destruction facility. This ACCS (Au-.C.u-.C.N Solution) Process Technology involves the novel application of copper cyanide chemistry. Standard resin processing and electrowinning equipment are used to recover the cyanide and produce the copper cathodes."

Jan 1, 1997

By R. J. St. Eloi

The Kidd Creek Copper Smelter has been expanded from its original design of 59,000 tonnes of copper per year to over 120,000 tonnes per year .. Modifications to the process gas handling system and acid plant have been made to accommodate this higher production rate and to .generally optimize the operation. The gas handling system associated with the continuous smelting process is discussed in terms of boiler accretions and modifications to minimize their impact on operations; design changes to effect reductions in high pressure drop duct configurations; material changes to overcome corrosion and plant additions to 'improve gas cleaning capability. The acid plant is reviewed with references to changes made to accommodate the increased S02 gas strength resulting from the higher smelting rates;

Jan 1, 1992

By R. Singh, C. Gong, J. Chaudhry

"Metalorganic chemical vapor deposition (MOCVD) is an ideal technique for the deposition of conducting and non-conducting oxide based thin film materials. In this paper we have presented a study of photo assisted MOCVD for the low temperature deposition of a number of oxide based advanced materials. We have used incoherent light sources as the source of optical and thermal energy in our MOCVD system. The vacuum ultraviolet (VUV) and ultraviolet (UV) photons can enhance the surface reaction of the absorbed molecules through the perturbation of the electronic state of binding between the absorbed molecules and the solid surface. Unlike plasma process, no surface damage is expected and high quality materials have been deposited. At a given substrate temperature, the performance of deposited film depends on the lamp configuration.INTRODUCTIONMetalorganic chemical vapor deposition (MOCVD) has become the standard manufacturing technique for the deposition of large area thin films of compound semiconductors. l.(.w-cost, high crystalline quality, atomically clean and sharp interfaces, atomic layer epitaxy, high throughput rates and potential for direct writing are some attractive features of MOCVD. Due to a number of potential advantages mentioned above, MOCVD is considered as an ideal technique for the deposition of various electronic and optical materials for a wide variety of applications. Rapid isothermal processing based on incoherent radiation as the source of optical and thermal energy is emerging as the key low thermal budget (integral of processing time and temperature) processing technique for the fabrication of current and next generation of microelectronic and optoelectronic devices and circuits [1]. In this paper we have demonstrated that the design of the lamp assembly plays an important role in determining the properties of the materials deposited by RIP assisted MOCVD. We have studied the growth rates, structural properties and electrical properties of Y2O3/Si structure. At a given substrate temperature, best results are obtained for the lamp assembly that provides maximum number of VUV and UV photons."

Jan 1, 1994

By E G. Prado

We have confirmed on bench scale the removal of chlorides and alkalies (+95%) and over 2/3 of the zinc, lead and cadmium from EAF dusts. This has been achieved with arrononium acetate solutions alone, or with combinations of water wash, amonia-ammonium carbonate and ammonium acetate solutions. Also confirmed are the process routes for the recovery of the aforementioned elements into marketable products. The technology involves the complete recycling of the reagents. The FAF residue is returned to the electric furnace without risk of impurities buildup. Commercial scale testing with the recycled dust was satisfactory, including quality of the slag and its behavior during the melting stage. A cursory feasibility evaluation is presented.

Jan 1, 1994

By C. J. Newman

The Kidd Creek Copper Smelter has been expanded from its original design of 59,000 tonnes of copper per year to over 120,000 tonnes per year. Modifications to the process gas handling system and acid plant have been made to accommodate this higher production rate and to generally optimize the operation. The gas handling system associated with the continuous smelting process is discussed in terms of boiler accretions and modifications to minimize their impact on operations; design changes to effect reductions in high pressure drop duct configurations; material changes to overcome corrosion and plant additions to improve gas cleaning capability. The acid plant is reviewed with references to changes? made to accommodate the increased SO2 gas strength resulting from the higher smelting rates.

Jan 1, 1992

By Andrew L. Puwis

Methodologies were presented for computing the thermal gradient associated with single crystal solidification in macroscopic computer modeling. The. heat transfer, and solidification of a shaped investment casting model were simulated using properties from three different alloys. Following the simulation of solidification, the resultant thermal gradients (G) and rates of solidification (R) from representative points were extracted in various ways and compared: It was discovered that alloy properties have a strong influence on the computed thermal gradient and rate of solidification for the three methods investigated. Data also showed that the computed gradient for each model was very different depending on the temperature range used to compute these values.

Jan 1, 1994

By Y. K. Rao

In the carbonyl process for the refining of crude nickel CO(g) reacts with nickel in the 310-370K range producing nickel tetracarbonyl, Ni(C0)4(g). Iron and cobalt impurities also form gaseous carbonyls but their partial pressures are low. The carbonyl is led to a decomposer plant wherein the gas disproportionates in the 500-600K range depositing pure metal on nickel pellets that move countercurrent to the gas-flow. This system serves to illustrate the fundamental principles involved in the vapor phase mass transport of elements, against temperature-gradient, under the influence of chemical potential gradient. Unlike in the crystal growth, the source is at a lower temperature (say 350K) whereas the seed is in the hot-zone (say 550K) of the closed ampoule-type reactor. By assuming virtual gas-solid equilibria in the end zones, with diffusion of gaseous species between them acting as a slight perturbation, the quasi-steady- state mass-transport rates are computed for a range of CO-pressures and temperatures.

Jan 1, 1993

By Suzanne Young

The effect of LiF additions on liqt.1id1.:1s temperature and electrical conductivity over a wide range of cryolite bath ratios (1.0 to 1.5 weight ratio) was investigated. Results did not agree with multi-regression equations reported by Dewing and Choudhary over the entire region. New regression equations were developed. Reasons? are given for the differences. The models are used to discuss the economic implications of LiF additions to Hali cell electrolytes.

Jan 1, 1985

Sanes are utilized to make molds for metal castings in the foundry industry. Approximately a half ton of sand is disposed of for each ton of metal cast in this country. The purpose of this investigation was to study and develop a process to separate chromite sand and silica sand from reclaimed sands for a steel foundry. Physical separations were utilized to yield silica and chromite sands with desirable molding properties. Several different separation methods, including electrostatic, magnetic, and various gravitational approaches were examined. Experimental results are presented. A method was developed to separate chromite sand from silica sand after mechanical or thermal reclamation. The reclaimed sands are passed through a rare earth magnetic separator to separate chromite sand and magnetic impurities from non-magnetic silica sand. Chromite sand can be recovered from magnetic silica sand or magnetic impurities very effectively using a wet concentrating table. The applicabilities of the separation methods are discussed.

Jan 1, 1995