Search Documents

By Alice Barreto Bevitori, Felipe Perissé Duarte Lopes, Denise Cristina Oliveira Nascimento, Sergio Neves Monteiro, Isabela Leão Amaral da Silva

"The piassava fiber is one of the most rigid natural lignocellulosic fibers, which has since the last decade been investigated as possible reinforcement for polymeric composites. In the present work, the tensile properties of polyester composites reinforced with piassava fibers with thinner diameters were investigated. Composites with volume fractions up to 30% of continuous and aligned piassava fibers were tensile tested at room temperature to evaluate the ultimate strength, elastic modulus and total strain. For each volume fraction, individually separated fibers with the smaller diameters were tested. The results indicated that the tensile properties tend to improve with increasing volume fraction of the thinner piassava fibers. The role played by the fiber/matrix interaction was analyzed by scanning electron microscopy.IntroductionA significant change in the transportation sectors mainly the aerospace and automotive, occurred last century with the introduction of stronger and lighter materials. The most relevant example was the polymer composite reinforced with synthetic fiber. They are nowadays replacing conventional materials such as the aluminum alloys in airplane body owing to superior specific strength. in recent years, however, environmental problems in a global scale are imposing a reversion in the use of synthetic fiber specially the glass fiber. In spite of its higher specific strength, this fiber and its polymer composites can neither be recycled nor incinerated in a thermal plant to generate electricity [1]. Moreover, the fabrication, processing and transportation of a glass fiber composite are associated with C02emission, the major responsible for global warming [2].A possible substitute for glass fiber without the above-mentioned environmental problems, could be a natural fiber. In fact, natural fibers obtained from cellulose-rich plants, also called lignocellulosic fiber, are already being used in several engineering fields, particularly the automobile industry [3-6]. Figure 1 illustrates an automobile and its many components made of lignocellulosic fiber composite [7]."

Jan 1, 2011

By Meifeng Zhi

Separation of uranium and molybdenum in the alkaline leach solution of a U–Mo ore was studied. A process of acidification-solvent extraction-precipitation uranium and molybdenum was determined. The influences of solution acidity and phase ratio of acidic scrubbing on separation of uranium and molybdenum were examined. The molybdenum extraction equilibrium isotherm was drawn. The results show that the separation of molybdenum and uranium can be achieved by acidifying the alkaline leach solution, solvent extracting molybdenum using trialkylamine at equilibrium pH 2.5, and scrubbing the loaded organic phase using sulfuric acid solution. The strip solution can directly precipitate ammonium molybdate. Uranium can be directly precipitated from the raffinat

By David R. Sadedin

The highly negative Gibbs free energies of hydrogen atom reactions suggest that refractory oxides such as titanium dioxide should be easily reduced by hydrogen atoms. These reactions appear to be most favourable at low temperatures; oxides should be reducible even at room temperature. Since hydrogen atoms are produced in plasmas containing hydrogen a number of investigators have used hydrogen plasmas of various sorts to test these possibilities for reducing refractory oxides, in particular TiO2. None of these attempts has succeeded, a small degree of reduction being achieved in only a thin layer near the surface. A deeper consideration shows that several factors complicate the reactions expected on the basis of the negative Gibbs free energy. One factor is that the back reaction by water molecules produces molecular hydrogen, not hydrogen atoms, and the metal atoms that have been reduced may be immediately re-oxidised. In plasmas there are complications due to diffusion, thermal and charge boundary layers and charged particle reactions. Interpreting the results of hydrogen atom reactions is difficult. Hydrogen is not detectable by electron dispersive spectroscopy and amorphous products are not determinable by x-ray diffraction. Another consideration is economics. The cost of producing hydrogen atoms has a large bearing on the metals for which hydrogen atom reduction may be competitive. In this paper these factors are discussed, some necessary basic studies are highlighted and the general principles of a laboratory reactor are given, together with the results of tests using ZnFe2O4, ZnO and TiO2 as test oxides.

Jan 1, 2006

By Li Ma, Shaoguo Chen, Gele Qing, Qihang Liu, Keng Wu

Olivine contains higher MgO element, which can be added into blast furnace burden to improve slag stability and fluidity. Effect of calcined olivine and untreated olivine on low silicon pellet production process and quality was studied in this paper. The results shows, calcined olivine has no effect on bursting temperature of green pellet, however the bursting temperature of green pellet will decrease with increase of untreated olivine ratio. Untreated olivine has slight effect on green pellet strength than calcined olivine while the ratio is higher than 2%. The compressive strength of low silicon pellet will increase first and decrease afterwards with increases of calcined olivine ratio under firing temperature of 1250°C, whereas, the changing sequence is reverse fired under 1280°C. The result of untreated olivine pellet compressive strength is same as calcined olivine pellet. However, the compressive strength and metallurgical property of calcined olivine pellet is slightly higher than that of untreated olivine pellet under same condition.

Jan 1, 2015

By Motoyasu Sato

Highly pure pig irons were produced in a multimode microwave reactor from powdered iron ores with carbon as a reducing agent in the nitrogen atmosphere. The grains in compacted powder absorb microwave energy selectively. Microwave-matter interaction creates thermal non-equilibrium state microscopically and enhances chemical reactions and the phase mixing at the grain boundaries very rapidly. The visible light spectroscopic techniques was used to monitor the progress of the reactions. Up to 650°C, the heated powders radiate the continuous spectrum of blackbody emission. The small non-equilibrium hot spots rise, move and finally burst in to brighter light emitting from all over the surface at 650°C. CN molecules and Fe (I) atoms were identified in the recorded spectrum. These bursts are similar to the ?ignition propagation? normally observed in chemical reactions. The line spectra originated from CO molecules have not been detected yet. The solid-solid reaction could be expected between the iron oxides and carbon to produce CO2 directly. A loss in the sample weight was accelerated during the excess-emission. These are the clear evidence that microwaves cause thermally non-equilibrium state and accelerate reduction process. The reduction of iron ore is completed at 1380°C and relatively very pure pig iron was produced. It should be noted that the impurity level of Mg, S, Si, P and Ti is only 5-10% of what is found in the pig irons produced by modern conventional blast furnaces in the steel industries. The necessary amount of carbon needed was 1/2 compared to conventional blast furnace to produce the unit weight of steel, if we applied renewable energy or nuclear power for the microwave excitations.

Jan 1, 2006

By S. A. Shuey

The present industrial practice used to separate aqueous cobalt from nickel is multistage solvent extraction processing. This paper describes a different but simpler treatment technology. The proposed technology has been applied to cobalt/nickel hydroxide intermediate solids produced from the treatment of Electrochemical Machining (ECM) waste sludge, The process consists of dissolving the cobalt/nickel hydroxides in basic cyanide solutions. Cobalt and nickel form aqueous .solution metal cyanide complexes. Nickel can be selectively precipitated from the solution as a nickellic hydroxide solid. Cobalt can be recovered from the leach solution by precipitation of a cobaltous/cobaltic cyanide double salt. The double salt product can then be subsequently treated to produce an appropriate cobalt product. The process chemistry, proposed fiowsheet and preliminary reagent costs are presented and discussed.

Jan 1, 1998

By Dominik Hofer

A broad spectrum of tantalum containing input materials can be processed for the production of synthetic tantalum concentrate (“SynCon”). The use of these low grade substances offers a secure alternative to mining of coltan in Central Africa. SynCon is produced in a multi-stage pyrometallurgical process, wherefore the melting behaviour of slags presents an important factor especially regarding the energy consumption and its optimisation. The characteristics of a slag comprising mostly Al2O3, CaO, SiO2 and MgO are influenced by the amount of other oxidic constituents which enfolds the main focus of this study. A hot stage microscope serves for the investigation of the slag behaviour in a temperature range from 1000 to 1600 °C under reducing atmosphere (CO/CO2 gas). The experimental results are compared with thermodynamic calculations (FactSage) to get a better understanding of the process.

By Petrus Christiaan Pistorius, Farzin Fatollahi-Fard

The production of synthetic rutile—a common starting material for most titanium production processes—from iron-rich titanium minerals such as pseudorutile and ilmenite is described. The process for “upgrading” the mineral to synthetic rutile is by carbothermal reduction of the mineral while immersed in a molten salt at high temperature, followed by magnetic separation of the reduced iron. A variety of factors are also investigated, such as particle size of the mineral, the type of mineral, and the molten salt used. The solubility of iron(III) oxide in different molten salts is also experimentally determined.

Jan 1, 2016

By Florian Kongoli

The behavior of cobalt as a by-product in the NilCu smelting and converting processes effects directly the quality of the final products as well as the revenues gained from the overall process. An effective way to evaluate and predict this important behavior is thermodynamic modeling which reduces the time and the cost of experimental investigation. In this work a thermodynamic model of cobalt-containing matte phase in NilCu smelting and converting processes is presented. The model predicts a priori the thermodynamic properties and phase relations of the ternary and multicomponent matte based solely upon the optimized parameters of the binary systems. This model can be used with other models such as those of slag, metal, gas etc. to predict various aspects of cobalt behavior such as matte- slag, metal-slag distribution, etc.

Jan 1, 1999

By Ruiling DU, Jiazhi Zhang, Yong Zhao, Keng Wu

Reaction kinetics of metallurgical physical chemistry which was successfully applied in metallurgy (as ferrous metallurgy, non-ferrous metallurgy) became an important theoretical foundation for subject system of traditional metallurgy. Not only the research methods were very perfect, but also the independent structures and systems of it had been formed. One of the important tasks of metallurgical reaction engineering was the simulation of metallurgical process. And then, the mechanism of reaction process and the conversion time points of different control links should be obtained accurately. Therefore, the research methods and results of reaction kinetics in metallurgical physical chemistry were not very suitable for metallurgical reaction engineering. In order to provide the definite conditions of transmission, reaction kinetics parameters and the conversion time points of different control links for solving the transmission and reaction equations in metallurgical reaction engineering, a new method for researching kinetics mechanisms in metallurgical reaction engineering was proposed ,which was named stepwise attempt method. Then the comparison of results between the two methods and the further development of stepwise attempt method were discussed in this paper. As a new research method for reaction kinetics in metallurgical reaction engineering, stepwise attempt method could not only satisfy the development of metallurgical reaction engineering, but also provide necessary guarantees for establishing its independent subject system.

Jan 1, 2015

By G. Fazel Jahromi

Enargite, known as one of the major arsenic containing copper minerals, with approximately 19% arsenic, introduces challenges to typical processing options. In most hydrometallurgical processing methods, arsenic remediation occurs after the copper recovery in an autoclave or in a stepwise neutralization process. In this study, the in situ precipitation of scorodite was investigated during an atmospheric leaching process in the presence of carbon-based catalysts and chloride media. The effective parameters of initial ferric addition, temperature, catalyst addition, and oxygen sparging rate were studied and the ferric behaviour was monitored during the scorodite precipitation. The most influential parameters on efficient scorodite precipitation are found to be: initial ferric addition, catalyst to concentrate ratio, and temperature. A 99% scorodite precipitation yield was achieved in this process.

By I. D. Reznik

The flowsheets of converter matte production from sulphide copper - nickel and oxide nickel ores on Severonickel and Yuzhuralnickel integrated ,;corks are given. The cobalt behaviour in electrosmelting and autogenous ore smelting, converting and converter slag cleaning is observed. A list of acticles published in the 80 th is given.

Jan 1, 1993

By Ragnhild E. Aune, Mark William Kennedy, Shahid Akhtar, Jon Arne Bakken

"To determine the heating rate of billets using ‘short coils’, an appropriate correction factor must be applied to the theoretical relationship. In 1945, Vaughan and Williamson published a semi-empirically modified Nagaoka coefficient applicable for moderate frequency induction heating processes (10 kHz). Recently it was demonstrated that the method of Vaughan and Williamson gives <10% error in the estimated power when heating aluminum billets at 50 Hz.In the present study, experiments have been conducted on aluminum billets in order to verify an empirical frequency corrected ‘short coil’ equation. Measurements of electrical conductivity (<± 0.5%), current (± 1%), heat (± 1-3%), and magnetic flux density (± 1-2%) have been performed. The results are compared with 1D analytical calculations, and 2D axial symmetric FEM modeling using COMSOL 4.2®. The frequency corrected equation has proven to provide accurate predictions of power (<4% error) within the frequency range 50 Hz to 500 kHz.IntroductionInduction heating is commonly applied to the re-heating of billets before forging or extrusion processes. The resistive heating produced by eddy currents in the solid or semi-solid work piece during this procedure, is driven by the time varying magnetic flux density in the air-gap between the work piece and the coil. The flux in the air-gap is created by the current flowing in the induction coil, i.e. the magneto-motive force. In Figure 1 it can be seen that the currents present in the work piece are concentrated in the outer ‘shell’, or the first electromagnetic penetration depth (dw), and flow in a direction which opposes the magnetic field produced by the induction coil."

Jan 1, 2012

By T. T. Chen

This mineralogical study is based on samples from typical "wet" nickel laterites of humid tropical to sub-tropical regions. An in-situ nickel laterite sample from Goro and a transported laterite sample from Plaine des Lacs, New Caledonia, are predominantly limonitic. Two-thirds of the particles in the Goro sample are <10 um in size; they consist of skeletal goethite and serpentine, as well as minor amounts of talc, gibbsite, chlorite, quartz and clay minerals. The coarser grains are mainly Cr-spinel, serpentine, gibbsite and Mn oxide. Nickel occurs mainly in goethite, serpentine and Mn oxide; cobalt occurs in goethite and Mn oxide. The Plaine des Lacs sample is finer-grained and contains more Al and CO3, but less Mg and Si than the Goro material. The sample contains more kaolinite, chlorite, siderite and feldspar, but less serpentine and gibbsite than the Goro material. Nickel is detected mainly in goethite, serpentine, Fe-Mg silicate and Fe-Mn oxide. The Indonesian ore from Sorowako, as sampled from the reduction kiln feed containing some reverts, is predominantly saprolitic, with apparent particle sizes ranging from <100 um to > 1 cm. The sample of reduction kiln feed is rich in Mg silicates, Mg-Fe silicates and goethite, and exhibits complex alteration textures. The nickel contents vary from particle to particle. Nickel is present mainly in serpentine, olivine, chlorite and amphibole, and in subordinate amounts in goethite and Mn oxide. Cobalt is detected in the Mn oxide. Keywords: Nickel Laterite; Mineralogy; Nickel Carriers; Goro, New Caledonia; Plaine des Lacs, New Caledonia; PT Inco., Sorowaki, Indonesia

Jan 1, 2004

By Mark Tjerkstra

In ,1993, the WMC Resources Ltd.-owned Kalgoorlie Nickel Smelter, underwent a capacity upgrade. This capacity increase was offset by .air quality control restrictions limiting the smelter&apos;s availability to 80%. As the direct. result of this limitation, WMC Resources Ltd commissioned a double absorption contact ,acid ,plant for the desulphurisation of furnace waste gas in August 1996. The history and the impact of the acid plant on S02 emissions and air quality is reviewed. General descriptions of the other aspects of the Kalgoorlie Nickel Smelter&apos;s Environmental Project are also included in the paper. Information on &apos;the design features? and operating practices that relate to or contrast with practices at operations visited by KNS personnel prior to acid plant commissioning provide the paper&apos;s focus. Smelter operation has changed markedly from unstable operation prior to 1997 to continuous" operation with little down time due to mechanical or process failures resulting in increased smelter availability to more than 90%

Jan 1, 1998

By S. Yin, A. Bogno, H. Henein, P. Natzke

Impulse Atomization (IA) (a single fluid atomization technique) was used to rapidly solidify Al- 4.5wt%Cu and Al-4.5wt%Cu-0.4wt%Sc under argon atmosphere. In addition to the IA-generated droplets, the same technique was used to produce strips by Spray Deposition (SD) of the same alloys on a copper substrate with and without oil coating. The rapid solidification microstructures were analyzed using Scanning Electron Microscopy (SEM). From the SEM images, the amount of eutectic and the secondary dendrite arm spacing (SDAS) were measured. These SDAS results lead to the estimation of cooling rate. The eutectic fraction coupled with the metastable extension of the solidus and liquidus lines of Al-Cu (Sc) phase diagram lead to the estimation of primary and eutectic undercoolings. A comparison of the solidification path of the droplets and the strips was done as well as the analysis of the effects of scandium.

Jan 1, 2015

By R. L. Nyirenda

An investigation of the reducibility of a cassiterite concentrate with charcoal was made in the temperature range of 1123-1373 K. The course of the reaction was monitored by a combination of sample weight loss measurements, product gas analysis, and chemical analysis of the reaction product. It was found that the cassiterite could be best reduced by a combination? of high temperature, reasonably high charcoal proportions, high charge poroslty, and the addition of a small percentage of lime. Analysis of kinetic data obtained from isothermal experiments using theory from the oxidation of carbon by carbon dioxide gave an activation energy value of 255 lci/mole for the consumption of carbon by reaction with cassiterite.

Jan 1, 1990

By Isabel Lázaro

A detailed study has been undertaken into the electrochemistry of the leaching of chalcopyrite in acidic solutions containing ferric ions. Mixed potential measurements have shown that the maximum potential achievable on a chalcopyrite disk in a ferric sulfate medium lies within the so-called passive or prewave region in the anodic behavior of chalcopyrite. The very low current densities due to the anodic oxidation of chalcopyrite at potentials in the region of the mixed potential has made studies of the initial stages of dissolution difficult. However a careful rotating ring-disk electrode (RRDE) study has enabled data to be obtained for the stoichiometry of the initial dissolution reaction to be obtained. Thus, in addition to the detection of soluble iron and copper as products in this potential region, a soluble sulfur species has also been detected. A comparison of the experimental with the expected collection efficiencies of the products on the ring has revealed that this soluble sulfur species is likely to be thiosulfate. The characteristic transient anodic behaviour of chalcopyrite in this potential region has been interpreted in terms of a rate limiting solid-state diffusion process. Thus, extrapolated rates based on reported measured solid-state diffusion coefficients for the mineral at elevated temperatures have been shown to be consistent with the potentiostatic current-time transients. Furthermore, comparative studies of the anodic characteristics of the copper sulfide minerals covellite and bornite has confirmed their greater reactivity in this potential region. The results of this investigation have been combined with a parallel study of the non-oxidative behaviour of chalcopyrite in order to derive a model for the dissolution process which is consistent with other published studies of the electrochemistry and dissolution of the mineral.

Jan 1, 2003

By J. P. Bellot

During the non-ferrous metal processing, the melting step under vacuum or under rarefied gas leads to volatile metal losses. It is the case of the metallurgical processing of the nickel-based, titanium-based or zirconium-based alloys where the evaporation losses don&apos;t allow a sufficient control of the alloy chemical composition. A theoretical approach has been carried out involving both a continuum description in the liquid phase and a molecular approach in the rarefied gas phase. The finite volume method is used in order to solve the coupled transport equationsin the liquid, whereas the Boltzmann equation is modelled by using a Monte Carlo method. At the liquid metal and metallic vapor interface, the volatilization and recondensation fluxes link up the two calculations. Simulation results are given for the melting and refining of reactive metals such as titanium alloys where the control of the chemical composition remains a major difficulty. The validity of the kinetic Langmuir&apos;s law is discussed for different operating conditions.

Jan 1, 1996

By Zhigan Deng

Cooling crystallization was used to separate iron (III) and nickel (II) from acidic sulfate solution produced by leaching of molybdenum-nickel black shale. The effect of K2SO4 concentration, crystallization temperature, solution pH and crystallization time on recovery of nickel (II) and precipitation of iron (III) was investigated, in order to obtain effective separation of nickel and iron. The optimum parameters determined were as follows: 200 g/L K2SO4, 10 °C crystallization temperature, solution pH of 0.5 and 24 h crystallization. Under these conditions, 97.6% nickel (II) was recovered as K2Ni(SO4)2, 6H2O crystals and only 2.0% of the total iron (III) was precipitated. Recrystallization yielded K2Ni(SO4)2, 6H2O crystals with a purity of 98.4%.