Search Documents

By Lyman H. Hart

Michiquillay is a major copper deposit situated about 70 km (44 miles) northeast of Cajamarca in northern Peru (Fig. 1). It occurs largely in quartz monzonite in a shatter zone produced by the intersection of northwest- and northeast-trending fault systems. The geology is described by Hollister and Sirvas (1974). The ore deposit was drilled in 1963-1964 by Asarco, with results indicating a resource of 575 Mt (634 million st) averaging 0.72% Cu-0.03% Mo. A decision to bring the project to production has been deferred because world capacity to produce copper has been more than adequate to serve world requirements since 1964. The chain of events leading to the discovery of Michiquillay was set in motion by a decision by the management responsible for the Chilete mine to undertake an investigation of the surrounding area for a possible supplementary source of mill feed to bolster its decreasing lead-zinc reserves. Chilete, located 100 km (62 miles) inland from Pacasmayo, is the most northerly, important mining project in Peru, and little was known of the mineral potential north and east of that point. Relatively unimpressive reports of Colonial silver mining had attracted little investigation, and little was known of the regional geology. One study by Benavides (1956) had been made of the Cretaceous in the region of Cajamarca.

Jan 1, 1991

By P V. Savage, T Glück, RCA Minnitt, C Bothma

Manganese Metal Operations ?Manganese Metal Company (MMC), a subsidiary of Samancor BHP Billiton, has two production facilities for electrolytic manganese metal in South Africa and produces a range of about 44 Mn metal products. ?The company is accredited with ISO 9000 and uses Six SigmaTM for continuous improvement. ?The control of the process relies on the effective functioning of approximately 250 different control loops at 50% automation.. ?Approximately 50000 samples are analysed every month. ?There are pyro, hydro and physical unit operations for the production of electrolytic manganese metal flake and value added products ? [ ]

Jan 1, 2005

By W. J. D. Stone

Many of the common valuable minerals have a magnetic susceptibility which is sufficiently high to render them amenable to magnetic separation. In addition,, many minerals which form the unwanted constituents of an ore can be removed by magnetic means. Magnetic separation in general has suffered seriously from, the lack of a high intensity wet separator. It is only recently that such a separator has become available to the industry. Prior to this, high intensity magnetic separation has been limited to the use of the dry techniques. Since the introduction of the Jones Wet High Intensity Magnetic Separator, extensive test work has been conducted to investigate possible applications. From the investigations conducted and the discussions that have taken place in the industry, it is apparent that the important mineral characteristic of magnetic susceptibility is not receiving the attention that it deserves. Applications for high intensity wet separation are being found in areas hitherto not considered.

Jan 1, 1963

By Gordon] [Reavis

Halliburton Services and Brown & Root have developed a unique foundation system that blends oilfield and construction technologies to construct deep foundations which offer significant advantages across a variety of soil profiles. This highly efficient system is being developed to meet the construction industry's needs into the 21st Century. Based on a concept initially introduced to Halliburton Services by V.L. Schellhorn in 1987, Halliburton combined their existing cement slurry mixing and pumping technology with oilfield drilling practices and a new tool design to field test the viability of the concept. Results looked encouraging, and Halliburton asked it's sister company, Brown & Root to evaluate and further develop the process. With Brown & Root's knowledge of the construction industry, the original concept has developed into a viable and efficient foundation construction system.

Jan 1, 1993

By Arthur F. Eidson

INTRODUCTION If a uranium mill worker is involved in an accident, analysis of excreta for uranium content and[in vivo] counting methods are used to estimate the extent of the possible exposure and to predict the pattern of uranium distribution among tissues (Spitz, [et al]., 1980). Interpretations of urinary excretion data are based on studies of human exposures to single uranium compounds including U02, U308, U03, UF4, U02F2 and UF6 (Alexander, 1974). Refined uranium ore (yellowcake) is a variable mixture of U03-NH3-H20 adducts (ammonium diuranate, ADU) and their thermal conversion product, U308. The variability in composition of yellowcake (Kalkwarf, 1979; Eidson and Mewhinney, 1980; Dennis, Blauer and Kent, 1981) complicates the interpretation of bioassay data from individuals that might have inhaled any single yellowcake material. A test system would be useful to estimate the dissolution behavior of a particular yellowcake aerosol inhaled by a worker and aid in the interpretation of bioassay data collected before and after an accident. A series of experiments was conducted for this purpose. The objectives of these studies were to: 1) develop specific criteria for comparing [in vitro] dissolution systems and 2) use the criteria to evaluate solvents, methods and experimental temperature and pH conditions used in previous studies. Dissolution experiments were conducted using different combinations of solvents, conditions and methods with a common yellowcake sample. Because little information is available from human yellowcake inhalation exposures to evaluate the [in vitro] results, criteria for evaluation of different tests were derived from a model of yellowcake dissolution in lung constructed from a number of cases in which humans were exposed to single uranium compounds known to be in yellowcake (Mercer, 1975). MATERIALS AND METHODS Materials The powder used in the tests was taken from one lot of yellowcake obtained from a commercial uranium mill. The same powder was previously designated as Mill D in Eidson and Mewhinney, 1980 and Mill 2 in Kalkwarf, 1979. The ammonium diuranate content was measured by infrared absorption to be 25% ± 1% (Eidson and Mewhinney, 1980). Solvents The compositions of the two biological fluid simulants used are compared in Table 1. Simulated lung fluid (SLF) (Kalkwarf, 1979; Dennis, Blauer and Kent, 1981) was chosen to simulate the composition [ ] of lung fluid as closely as practical (Moss, 1979). Simulated blood serum ultrafiltrate (SUF) (Eidson and Mewhinney, 1980) was chosen because of previous successful efforts to model human urinary excretion of inhaled plutonium aerosols (Kanapilly Raabe and Boyd, 1974) and the dissolution rate of 241Am02 in Beagle dogs (Mewhinney and Griffith, 1981). Major differences are that simulated lung fluid contains Mg2+ and a higher Ca2+ concentration than SUF and that SUF contains ammonium ion. Both solvents include protein substitutes; acetate is used in SLF, while amino acids are used in SUF. Both solvents include phosphate but the chelating agent diethylenetriaminepentaacetic acid (DTPA) is included in SUF to prevent possible formation of insoluble uranyl phosphate precipitates that would result in an underestimation of solubility. In addition to the above solvents, modified solvent compositions were prepared to investigate the role of specific salts in yellowcake dissolution studies. Solutions of SUF (Table 1) were prepared without DTPA (SUF-DTPA) and without amino acids (SUF-amino acids). No solution excluded both DTPA and amino acids. The SLF solutions were prepared with DTPA (SLF + DTPA) and without phosphate

Jan 1, 1981

By F. G. Miller

It is generally accepted that sulfur exists in coal in three forms: (1) pyritic, (2) organic, and (3) sulfate sulfur. Sulfate sulfur usually makes up less than 1% of the total sulfur content. Pyritic and organic sulfur, make up almost all of the total sulfur and occur in varying amounts in different coals and can vary greatly in coal of the same seam Pyritic sulfurs of 20% to 80% of the total sulfur have been reported Other authors have shown that it is not possible to remove the organic sulfur without chemically altering the coal. Chapman and Jones (1) state: "Organic sulfur, unlike pyritic sulfur does not exist as discrete particles, but is intimately associated with the coal structure, and as such it is not possible to remove it or reduce its concentration by physical means." Any success in removing sulfur has come about by removing pyritic sulfur by physical means; therefore, removal of sulfur in the pyritic form is the subject of this investigation. The extent to which any impurities can be removed from a particular coal can be determined by a washability study. Outside of crushing coal, to finer sizes or chemically altering the coal, there are no known methods of changing this inherent washability characteristic. The efficiency of various methods used to remove impurities can be determined by comparison of results produced at a yield to the results as shown by a washability study. In recent years heavy media processes have proven their ability to wash plus 28 mesh coal and nearly produce results shown to be theoretically possible by the washability study. Therefore, it is the objective of this paper to show various methods of treating the finer fractions of the coal, in the hope of developing a process, which can effectively produce in the fine fractions the efficiency of heavy media devices in the coarse.

Jan 1, 1963

By George I. Staber

As stated by the Congress in the preamble of the act establishing the Office of Coal Research, its purpose is, "To encourage and stimulate the production and conservation of coal in the United States through research and development by authorizing the Secretary of the Interior to contract for coal research, and for other: purposes." Thus, while the overall responsibility for air pollution control from all sources rests primarily with the Department of Health, Education and Welfare, it is obvious that OCR could not perform its mandate of, increasing the utilization of our Nation's greatest energy resource if it ignored one of the greatest practical obstacles to achieving that objective. Therefore, air pollution abatement and prevention is one of the practical considerations taken into account in the selection of the OCR program. And as the severity of the air pollution problem imposes new restrictions on the use of coal, the importance of this criteria in the selection of OCR projects increases. The work done by OCR in air pollution abatement does not conflict with nor does it duplicate the program developed by HEW's National Center for Air Pollution Control. Technical members of the OCR staff maintain close formal and informal liaison with their counterparts in NCAPC. One formal agreement has been executed whereby the HEW agency has transferred funds to OCR for a practical study of the potential effectiveness of air pollution control when coal is burned in a fluidized bed comprised of inert alkaline earth material. It is hoped that this initial cooperative effort will be

Jan 1, 1968

By Hae-Moon Choi, Sang-Don Lee, Hee Soon Shin, Choon Sunwo, Chang-Ha Ryu, Hyun-Koo Lee

Building tunnels means dealing with what rock is encountered. Relocation of the site of the underground structure is rarely possible. Tunneling engineers and miners have to cope with the quality of the rock mass as it is. Different tunneling philosophies and different rock classification methods have been developed in various countries. Most of the rock classification methods are based on the response of the rock mass to the excavation. Tunnel support requirements could be assessed analytically, supplemented by rock mass classification predictions, and verified by measurements during construction. Rock mass classifications on their own should only be used for preliminary, planning purposes and not for final tunnel support. Design of blast pattern in tunneling projects in Korea is also for the most part prepared according to the general rock classification methods such as RMR or Q. It, however, does not take into account the blast performance, and as a consequence, produce poor blasting results. In this paper, the methods of general rock classification and blast design for tunnel excavation in Korea are reviewed, and efforts to develop a new classification method, reflecting the blasting performance, are presented. Copyright ©

Jan 1, 2004

By Thierry Bernard

Considering rock fragmentation by explosive as the ultimate goal in mines and quarries, vibrations are definitely one of the main drawbacks faced by the Industry. If we can accurately predict vibrations level and frequencies, taking into account the whole set of the involved parameters, this will bring a major benefit to each of us, in our daily production process optimization effort. The model presented in this paper answers to this need thanks to a "holistic" approach of the vibration mechanism. By holistic, we mean that we approach the vibration effect (wave propagation) as a whole, by understanding all of the mechanisms that contributes to the process and comprehending how they are connected.

Jan 1, 2009

By Tim M. Benson, Adam L. Lamanna, Carolina Martinez-Gutierrez, Mark J. Stephani

The Lower Concourse C Extension (LCE) 108-in Storm Sewer consists of a 2,797-foot long, 27 to 55-foot deep, 108-in I.D. storm sewer tunnel. Situated beneath active taxiways and a terminal apron at Hare International Airport (D), the tunnel diverts ows from existing storm sewers located within the footprint of a future satellite concourse. The project was delivered via Construction Manager at Risk (CMAR) as part of Chicago Department of Aviation’s (CDA) ongoing O’Hare 21 Capital Program. This paper presents project details, multiple stakeholder coordination, subsurface risks and challenges, TBM performance, and impacts to existing infrastructure.

Jun 23, 2024

By Serhat Baycan, Mikias Yohannes

"Kuala Lumpur Karst is a complex limestone formation that is characterized by presence of cavities, solution channels, pinnacles and floaters. Basement excavations in such geological formations are usually challenging, mainly owing to the unpredictable rock head depths and potential for groundwater inflow. Any excavation support system should have adequate robustness and water tightness. Traditionally, Secant Bored Pile walls (SBP) with struts are the preferred option for karst ground. This paper discusses a cost effective and innovative alternative solution for a particular site – using Deep Soil Mixing (DSM) and using Contiguous Bored Piles (CBP) together with Ground Anchors (GA). The site, located around one of the busiest areas of Kuala Lumpur, is a 5,700 m2 commercial and residential development. A 16.0 m deep excavation was needed for four levels of basement and excavation support along the 275 m perimeter of the development. Within the site, the depth to rock head varied from 6 m to 19 m. The basis for each solution and conditions for its suitability are discussed in detail. Some design considerations and construction challenges are also presented. The performance of the two retention systems during excavation are presented, together with comparisons versus design predictions. Suggestions for future development are also given. Advantages of this approach compared to other traditional approaches are highlighted.1. INTRODUCTIONThe geology of Kuala Lumpur is among the most complicated and geotechnically challenging formations in South East Asia. The majority of the city falls into the Kuala Lumpur Limestone formation; which is a thick, highly-weathered and cavernous limestone. This formation is pure calcitic to dolomitic in composition, having infrequent schist and phyllite interbedding (Gobbett et al., 1973).The KL limestone has a highly karstic topography dotted with cavities, ravines, interconnected subterranean channels, pinnacles, overhangs, floaters and slump zones (Tan, 2006). This results in erratic bedrock profiles even within short distances. It is not uncommon to see a precipitous rock head incidence within short distances in the same site. In most parts of the City, the bedrock is typically encountered ranging from very shallow depths to about 30.0 m. The exception to this is at the heart of the City, where Kenny Hill formation prevails above the KL limestone. In such cases the limestone bedrock can be encountered much deeper. The erratic rock head profile and the highly karstic nature of the KL limestone makes it a geotechnical challenge requiring careful consideration of suitable engineering solutions.1.1 – Site DescriptionThe site, located in downtown Kuala Lumpur, is abutted by a busy street on the North. Before development, the site previously served as a car park. To the west an access road separates the site from an empty lot; while on the east, the lot is bounded by light weight residential and commercial buildings. On the south side, the site is bordered by a road that separates it from a prominent Shopping Mall in the City. A layout plan and an artist’s impression of the finished development is shown in Figure 1."

Jan 1, 1900

By Abhishek Asthana

The incineration of Municipal Solid Wastes (MSW) is an attractive process for reducing the volume of the wastes and recovering their energetic value, which, however, requires to be strictly controlled in order to limit its impact on the environment. In this context, we have undertaken the mathematical modeling of the different sections of a typical incineration plant. The combustion of the waste bed, usually carried out on a moving grate, is at the core of the process. This paper presents the 2-dimensional, steady-state model that we have developed for simulating the MSW combustion. The model describes gas flow through the porous waste particle bed, the gas-solid reactions, conductive and radiative heat transfers, drying of the feed, its pyrolysis and the emission of volatile species, combustion of the pyrolysis gases, the formation of char and its gasification by water vapor and carbon dioxide, and the consequent reduction of the bed volume. Pyrolysis kinetics distinguish between cellulosic and non-cellulosic materials and are experimentally derived from our laboratory measurements. The calculated results give a deep insight into the various involved phenomena, an example being the complete consumption of oxygen in a large zone of the bed and the related appearance of a char gasification zone. The influence of various operating parameters, like the temperature and flow rate of primary air, is presented and explained. Finally, the effect of stirring the waste bed on the moving grate is also analyzed.

Jan 1, 2006

By Smith I. K

A Data Acquisition System with a capacity to monitor 2000 analog instruments has been installed at the mines operated by the Zinc Lorporation, Limited and New broken hill Consolidated Limited (ZC/LVbHC), New South Wales, Australia. Since commissioning in March, 1982, the system has proved its value in providing up-to-date information to both Rock Mechanics and Mining personnel. The paper describes the function of the major software and hardware components of the system, and identifies the advantages that an on-line monitoring system provides in the day-to-day operation of a large underground mine.

Jan 1, 1983

By E. Pribonic

Failure of a mine material hoist can cause injuries, fatalities and significant infrastructure damage, along with an associated loss of production. Principal causes of hoist accidents are overwind and underwind. Past and present means of arresting hoisting equipment are marginally effective and utilize destructive systems that are not reusable following an arrest. The use of permanent magnet eddy current arrestor technology is proposed; the history and fundamental science of the technology are presented, followed by real world examples and calculations of performance for failsafe, friction-free, instantly reusable eddy current arrestors as applied to stopping a 30-ton ore skip traveling at 16 metres per second. A comparison of existing arrestor types with the eddy current arrestor is included and limitations of the ECA are also discussed.

Jan 1, 2008

Projected cooling requirements for ERPM led to the first proposals for the large- scale use of ice for mine cooling in the early 1980's. Following successful research into ice conveying and ice melting a large ice plant was commissioned at Harmony in 1985 and a much larger 6000 ton per day plant is presently under construction at ERPM. A brief description of the mining project is given, followed by general descriptions of the surface ice plants and the ice conveying system, the systems for using the ice for mine cooling, and the control of the whole ice cooling System.

Jan 1, 1988

By H. Y. Sohn, M. Pérez-Tello, P. J. Smith, K. M. Riihilahti

A three-dimensional computer model for the Kennecott-Outokumpu flash converting process for copper matte is presented. The model incorporates the transport of momentum, heat and mass, and reaction kinetics between the gas and particles in a particle-laden turbulent gas jet. The k-E model is used to describe gas-phase turbulence in an Eulerian framework. The particlephase is treated from a Lagrangian viewpoint which is coupled to the gas phase through the source terms in the Eulerian gas-phase governing equations. Matte particles were represented as Cu2S·yFeSx. Based on experimental observation, the oxidation products were assumed to be Cu2O, CuO, Fe3O4, and SO2. A reaction mechanism involving the external mass transfer of oxygen to the particle surface and diffusion of the oxygen through the oxide layers of CuzO/Fe304 and CuO/Fe3O4 is proposed. Predictions of the mathematical model were compared with the experimental data collected in a large laboratory furnace. A reasonable agreement between the model predictions and the measurements was obtained in terms of fractional conversion of the oxidation reactions and of sulfur remaining in the reacted particles. The simulation of an industrial flash converting furnace was also performed. Higher oxidation rates, more even distribution of particles, and thus a more efficient use of the reactor volume are predicted with a burner having a distributor cone, than with a single-entry burner.

Jan 1, 1999

By G. K. Ruhlandt, C. W. Kim

"A 3-D Finite Element Method program called ""SOLCAST"" has been developed to simulate the casting solidification process. Using the temperature recovery method to evaluate the latent heat of fusion and applying a new combination of the time integration scheme, SOLCAST reduces the computational time significantly compared to an existing commercial FEM program, and produces accurate results comparable to experimental casting results. Prediction of casting shrinkage porosity for A390 aluminum alloy will also be discussed. To make this FEM program useful for foundry engineers, this program was connected to a commercial pre- and post-processor.IntroductionBecause of recently increased competition, foundrymen must produce high quality castings more economically. Therefore, casting solidification analysis prior to casting production is an attractive way to reduce costs and development time.Although the actual casting solidification process is a very complicated phenomena, foundrymen could predict where shrinkage defects would occur based on a transient conduction heat transfer analysis that includes the liberation of latent heat. A numerical analysis is generally required to solve the heat diffusion equation with the latent heat diffusion term, because casting shapes are very complicated and pure materials are rarely used.Different numerical methods have been applied to the casting solidification analysis 1. Among them, a finite difference method 2 and a finite element method (FEM)3 are most commonly used.Each simulation method has one or more basic difficulties which are different for each method. These difficulties are:(1) Modeling casting shapes on a computer.(2) Time consuming computation.(3) Uncertain material properties."

Jan 1, 1986

By Li-min Liu

The Semi-Analytical method can be used to solve a variety of problems in geomechanics and civil engineering. When it comes to layered rock strata and rock masses, it is superior to all other analytical methods. This paper presents the application of a 3-D semi- analytical method to 3-D surface subsidence and stress analysis caused by mining. In this semi-analytical method the layered elements and triangular elements ate used alternatively. Their displacement pattern, strain mahix, elastic matrix, stiffiness matrix, load matrix and stress matrix are presented. A numerical simulation program based on the semi-analytical method bas been developed using Fortran 90. This program is suitable for subsidence prediction and stress analysis of mom and pillar mining, strip longwall and mechanized longwall mining methods. It is applicable to all geological conditions and mining methods. Comparing with the finite method, this method reduces significantly the number of simultaneous equations to be solved and the amount of data preparation. It not only reduces the computer memory, but also runs faster and cost less. Key Words Semi-analytical method, surface subsidence, stress analysis, layered element, triangular prism element

Jan 1, 2002

By W Zeng, D Walker, D Cai, E Baafi

"The efficiency of the truck-shovel haulage system is significantly influenced by the truck fleet size. A discrete event simulation model with 3D animation has been developed to estimate the productivity of a truck-shovel network system, shovel efficiency, truck cycle time, truck utilisation and the optimal fleet size. The simulation model considers the dynamic variability of traffic conditions and also the truck as an individual entity. The resulting truck cycle time was found to be realistic and thus providing a better tool for strategic mine planning.Citation:Zeng, W, Baafi, E, Walker, D and Cai, D, 2016. A 3D Discrete Event Simulation Model of a Truck-shovel Network System, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 265–273 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By B. I. Hop

The f10wfield set up by the standard Hydro gas purging unit has been predicted by a numerical model. In addition turbulent trajectories of gas bubbles released from the rotor are predicted. Here the deposition rate of inclusions on the bubble surface is allowed to depend on local conditions. Bubbles passing regions with strong pressure gradients, such as close to the rotor, will experience large slip velocities and large deposition rates. This model can deal with any distribution of bubble sizes and inclusions. The results found from the multidimensional flow predictions are discussed in relation to what can be obtained from a much simpler metallurgical engineering approach. The differences between these two approaches to predict the same process will be discussed. The model predictions are compared to experimental results for removal of SiC-particles from aluminium.

Jan 1, 1996