Search Documents

By Erik Westman, BEN WESTON, SETAREH GHAYCHI AFROUZ, KATHRYN DEHN

One of the most difficult challenges in underground mining is to forecast significant seismic events prior to their occurrence in order to support the safety of miners and to minimize damage to the underground operation. Passive seismic tomography is a tool to image the seismic velocity changes in a rockmass, which can potentially reveal the rockmass behavior before and after a significant seismic event. In this paper, the changes in seismic velocity of the rockmass before and after three major seismic events are investigated to determine whether there are identifiable precursory velocity changes associated with the major seismic events. Conventional mechanics imply that the induced stress at the hypocenter would continue increasing until failure, in the form of an induced seismic event, occurs. With passive seismic tomography we can image changes to the seismic wave velocity distribution within a rockmass and hence infer the changes to the induced stress near the hypocenter. This paper evaluates the hypothesis that induced stress at the hypocenter (as inferred by the p-wave velocity) increases until the seismic event occurs. In addition to analyzing p-wave velocity changes near the hypocenter, changes to the p-wave velocity at “zone centers” were also analyzed. These “zone centers” are regions within the rockmass that consistently have a p-wave velocity that is much higher than the average p-wave velocity for the rockmass. It is found that the p-wave velocity did not increase at any of the three hypocenters prior to the seismic event occurring, however the p-wave velocity did increase in the closest “zone center” for two of the three events.

Oct 12, 2020

By Shuchen Sun, Ganfeng Tu, Chuan Liu, Xiaoping Zhu

The hydrometallurgical residue generated during the hydrometallurgical processing of waste automotive catalysts is valuable as a secondary resource. In this study, a process of platinum recovery from the hydrometallurgical residue by high-temperature smelting process was proposed. Results of lab- and pilot-scale experiments show a high recovery of more than 98% of platinum and glass slag was successfully obtained by controlling the Fe3O4 addition, C/Fe3O4 mass ratio, CaO/SiO2 mass ratio, smelting temperature, and holding time at 15 wt%, 0.4, 0.6, 1500 °C, and 120 or 60 min, respectively. Results from the pilot-scale show that the platinum contents in the glass slag and alloys were less than 4 g/t and more than 0.6 wt%, respectively. Therefore, the process proposed in this study is a prospective and effective approach for reutilization of hydrometallurgical residue containing platinum.

Oct 12, 2020

By MARK J. VANARELLI

Estimating groundwater inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies for estimating steady-state groundwater inflows into deep rock tunnels. The case studies included the Chattahoochee and Nancy Creek tunnels. In this paper, statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations. A semi-empirical procedure was utilized for estimating groundwater inflows into these deep rock tunnels. It is the most widely used method/procedure in the tunnel industry. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels which exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semi-empirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Packer test data plotted in histograms were observed in all cases to be log-normally distributed for the radial flow condition. Modeling using Monte Carlo simulations was observed to be an effective tool for removing irregularities in the distribution of the data and incorporating high-end permeability data to derive reasonable groundwater inflow estimates. This paper is based on the PhD thesis entitled “Improvements to the Current State of the Practice in Steady-State, Groundwater Inflow Estimates into Rock Tunnels based on the Application of Statistical Analysis Methods of Packer Test Data obtained from Exploratory Borings During Geotechnical Site Investigations.”

Oct 9, 2020

By Karoly C. Kocsis, Kyle A. Scalise, Marcelo Bandeira Teixeira

Understanding the effects of various ventilation and climatic parameters on the work conditions and comfort in underground mines is critical for efficient ventilation system design and cost savings and to ensure the health and safety of mine workers. To understand the effects that the thermal damping effect (TDE) and the thermal flywheel effect (TFE) have on the ventilation system design and potential cooling system, this paper compares and analyzes the wet and dry-bulb temperatures at the bottom of an intake shaft using two modeling software packages, Ventsim™ and Climsim™. The comparison shows the consequences and importance of taking into account the TDE/TFE when predicting the climatic conditions in future underground mines, especially when deciding on whether a cooling system should be employed in order to provide adequate climatic conditions in the production stopes, dead-end development headings, and throughout the mine. Ventsim™is able to account for the TFE, while Climsim™does not. Both software packages have their uses and are used within the mining industry, but it is useful to understand their limitations and where the future of underground climatic modeling will lead.

Oct 9, 2020

By S. D. F. Rocha, A. L. A. SANTOS, E. M. A. BECHELENI, R. M. Papini, P. R. M. Viana, F. P. C. Silvas

The kinetics of atmospheric sulfuric acid leaching from a Brazilian nickel laterite ore was assessed using distinct reducing agents and ore mineralogy. This transitional ore contains 1.63% Ni distributed as 1.27% in coarse size (− 500 + 150 μm), mainly as silicates (lizardite and chlorite—28.6%), and 2.06%in the fines fraction (− 75 μm), mainly as iron oxy-hydroxides (goethite and hematite—49%). The effects of temperature, acid concentration, reducing reagent type, and concentration were evaluated. The − 75 μm fraction limited the leaching efficiency and the use of reducing media with thiosulfate improved leaching and Ni-Fe selectivity. However, at constant Eh of 626–743 mV and a pH range between 0.2 and 1.1, no substantial rise in metals extraction, except for Co and Mn, has been observed. In order to determine the process control at 95 °C, two regions in the extraction curves were used in combination with the shrinking core model. Control by porous diffusion was observed and the kinetic constant was found to be in the order kFe<kNi<kMn<kCo<kMg for atmospheric leaching without Eh control. In reducing media for the first 15 min of leaching, the kinetic constant was found to be kFe<kNi<kMg≅kCo<kMn as derived from Ni disseminated into iron oxides structures.

Oct 7, 2020

By Liaqat Ali, Robert Chapman, Asghar Ali, Mohammad Tahir Shah, Seema AnjumKhattak, Mohammad Farhan

Alluvial gold is abundant in the Quaternary deposits of the Kabul and Indus rivers in District Nowshera, Khyber Pakhtunkhwa, Pakistan. Understanding the provenance of alluvial gold using morphology and elemental composition could be helpful in developing an exploration strategy of regional benefit. Detailed morphological studies of gold grains revealed high flatness index values which are indicative of a distal source. Compositional studies of 58 gold grains using SEM and EMPA showed broadly similar Ag ranges (1– 15 wt%) for each sample and occasional Cu values in individual gold particles to 0.4 wt%.Whilst the Ag profile is not diagnostic, the Cu values are compatible with derivation from either porphyry systems or ultrabasic rocks. The complex geology of the drainage catchments could host gold mineralization of other styles, but larger sample suites would be required to refine the current interpretation to establish whether particles which are simple Au-Ag alloys could be derived fromorogenic or epithermal sources. This scoping study has demonstrated that the compositional and morphological studies of gold grains are useful in providing information regarding the nature and location of the source of placer gold in areas where there is limited information on the nature and location of in situ mineralization.

Oct 6, 2020

By Mingfei He, Jianhua Chen, Yingchao Liu, Yuqiong Li

Pyrite is one of the most common sulfide minerals on earth, which is usually grown with chalcopyrite and other sulfide minerals. In flotation practice, pyrite from different mines or different sections in a same mine may have different flotation behaviors. This is because the pyrite crystal contains lattice defect, including ionic vacancy and lattice impurity. The present work investigates the effects of three typical 3d transition metal (Co, Ni, and Fe) on the adsorption of CH3OCS2 −, OH−, and CN− on pyrite surface by density functional theory (DFT) calculations. Calculated results show that Co impurity reduces the adsorption energies of CH3OCS2 − and CN− on the surface of pyrite, while Ni and Cu impurities significantly increase the adsorption energies of CH3OCS2 − and CN− on the surface of pyrite. Co impurity has small influence on the adsorption of OH−, but Ni and Cu impurities significantly increase the adsorption energies. Calculations on Mulliken charge population of Co2+, Ni2+, and Cu2+ indicate that the Mulliken charges of Co2+, Ni2+, and Cu2+ after OH− adsorption are more than those after CN− adsorption. This suggests that the ionic property of the M-OH- coordination bond is greater than that of M-CN- coordination bond, while covalent bonding of M-CN- coordination bond is greater than that of M-OH- coordination bond. The adsorption results are discussed based on coordination field theory (CFT).

Oct 6, 2020

By K. V. Raj, R. Jacksha

Conveyor systems persist in being a source of injuries and fatalities in the mining industry. To reduce these incidents, better methods are needed to enhance the monitoring of probable hazards and improve situational awareness during the normal operation and maintenance of conveyor systems. To address these issues, researchers from the National Institute for Occupational Safety and Health (NIOSH) continue to investigate emerging technologies that show the potential to improve miner safety around conveyors. This paper presents a feasibility assessment by NIOSH researchers of a fully integrated, commercially available wireless Internet of Things (IoT) system to improve situational awareness around conveyor systems. Included are discussions of a full-scale laboratory test bed that was designed to simulate a working conveyor system as well as the challenges and successes of integrating the IoT system with the test bed.

Oct 6, 2020

By Paloma Lazaro, Moe Momayez

Interactions between human beings and their work environment require the body to regulate its temperature by balancing heat production and loss. Comfortable environmental conditions are crucial for keeping workers safe and healthy and to maintain a suitable level of productivity. However, achieving a proper core body temperature may become challenging under different conditions, especially in high heat-generating workplaces such as hot underground mines. Because hot underground mines have the potential to expose workers to heat stress, compliance with standardized and regulated indices and criteria is distinctly required. The objective of this paper is to provide an overview of the current research on heat stress and strain in hot underground mines, collected from published and specialized literature. General definitions, statistics of heat-related accidents in mining, overview of the indices, standards, and recommendations for heat stress are provided herein.

Oct 6, 2020

By Yehia M. Youssef, Nourhan Moukhtar, M. H. Abdel-Aziz, Ibrahim Hassan

Copper was recovered from copper sulfate solution in a batch-recycled galvanic reactor operated under forced convection with the generation of electrical energy during the cementation process. The divided galvanic cell consisted of parallel copper and zinc plates. The mass transfer rate and the amount of electrical energy generated were found to be directly proportional to the solution flow rate and the initial concentration of metallic ions and inversely proportional to the distance between electrodes. The experimental results were expressed in terms of a dimensionless correlation including all parameters. The wastewater treatment presented herein cell can be utilized to recover many soluble heavy metal ions from solution with high efficiency.

Oct 2, 2020

By José Galíndez

Frente a una población rural aproximada de 6 millones de habitantes que enfrentan fuertes carencias en infraestructura y servicios básicos, el autor concluye que en Perú “no se podrá lograr el desarrollo sostenible ni para las empresas ni para las comunidades, si no cambiamos sustancialmente la manera en la que se viene gestionando esta relación”. El artículo detalla la importancia de promover y alcanzar, en el sector mineroenergético, acuerdos estratégicos sostenibles sobre manejo de residuos y reciclaje; capacitación en agricultura, piscicultura y actividades afines; desarrollo de programas de salud y educación y de uso de energías eco-amigables.

Sep 30, 2020

By Juan Carlos Llorente

Orientado a ingenieros y otros profesionales relacionados con el sector minero y energético, este artículo reflexiona sobre el fundamento de los actuales criterios de sostenibilidad medioambiental y climática para la actividad minera. Entre otros aspectos, el autor aborda temas tales como el uso de energías renovables en el sector y sus implicancias, el cumplimiento de las obligaciones medioambientales, y el comportamiento de la minería formal e informal.

Sep 30, 2020

By Carlos Rabanal, Levi Guzmán

El éxito del proceso de conminución, desde la trituración hasta la molienda, se centra en la relación entre el consumo de energía y el tamaño de partícula producido. La metodología optimizante propuesta por el autor —y desarrollada por Molycop— provee soluciones integrales para diferentes circuitos de molienda-clasificación, las cuales se traducen en mayores tonelajes de mineral procesado, óptimos consumos de medios de molienda, incrementos en la eficiencia energética y de clasificación y otros beneficios tangibles para las operaciones.

Sep 30, 2020

By Francisco Sotillo

El artículo da cuenta de una investigación orientada a demostrar los beneficios del mecanismo de conminución en una cama de partículas, como ocurre en los rodillos de molienda de alta presión (HPGR) o molinos de rodillos de alta presión (HPRM). Se ha investigado el uso de los HPGR de laboratorio para mejorar la eficiencia de separación de los minerales con alto contenido de dolomita, ultra alto contenido de arcilla y alto contenido de arcilla (kaolinita) presentes en una mena de apatita en operaciones subsiguientes «aguas abajo» de beneficio de diferentes minerales de fosfato de origen sedimentario. La investigación incluye estudios de caracterización de minerales de fosfato dolomítico, datos del modelo físico aplicado por PerUsa EnviroMet, Inc. de HPGR para desarrollar información preliminar de conminución; y evaluaciones de HPGR de laboratorio para determinar los parámetros de chancado (velocidades de alimentación; velocidad y separación de los rodillos; torque, presión y energía aplicables).

Sep 30, 2020

By Fathi Habashi

Tras pasar revista a diversos ejemplos de procesos químicos propios de la metalurgia extractiva —referencialmente clasificados como piro, hidro y electrometalurgia—, el autor muestra cómo, por ser más eficientes, económicas y/o cumplir con las modernas regulaciones ambientales, las últimas tecnologías vienen desplazando gradualmente a las más antiguas. Tal es el caso de las recientes investigaciones sobre una nueva tecnología para la producción electrolítica de aluminio que excluye la reducción de carbono, con el fin de eliminar la producción de CO2.

Sep 30, 2020

By Juan Beltrán

Durante el tiempo de operación de la refinería de Ilo, el teluro ha ocasionado problemas operativos en la calidad de depósito, al contaminarlo química o físicamente. El objetivo del presente estudio fue minimizar la concentración de teluro en la solución de agua madre, producto de la lixiviación de lodo anódico, mediante el proceso de cementación de teluro con cobre. En las pruebas desarrolladas en planta se alcanzó una extracción de 24% de Te, lo que hizo posible dar mayor valor agregado a los subproductos de la refinería.

Sep 30, 2020

By Emre Karakaya, Niyazi Bilim

Boreholes are used for many purposes in mining operations, petroleum engineering, and construction works. Numerous factors affect the performance of drilling equipment. Researchers continue to work on the variable drilling parameters that can be adjusted in order to reach more efficient drilling operations. Penetration rate is an essential indicator in drillability analysis and estimating. This parameter is of great importance in mining projects. There are almost no models that can estimate the penetration rate for core drilling operations. Under the abovementioned circumstances, this paper focuses on developing models that allow estimating the penetration rate based on rock material properties. During the conduct of this study, drilling experiments under 11 different pressure forces were performed on 8 different rock units, and the equations which estimated the penetration rate depending on the physico-mechanical properties of the rock samples were derived. Experiments were carried out under different pressure forces to investigate the effect of the pressure force on the derived estimation models. The obtained results allowed deriving equations that ensured estimating the penetration rate based on the physico-mechanical properties of the rocks and the applied pressure force. Using these equations, the penetration rate in core drilling operations can be estimated.

Sep 30, 2020

By MUSTAFA ERKAYAOGLU, Muhammet Mustafa Kahraman

Particulate matter (PM) is one of the main actors related to air pollution caused by surface mining. Fugitive dust, considered as particulate matter that cannot be collected by conventional measures, is classified by the particle size. The Environmental Protection Agency (EPA) categorizes PM as coarse and fine particles based on the particle size being less than 10 μm (PM10) and less than 2.5 μm (PM2.5). Basic operations of surface mining such as drilling and blasting, loading, haulage, and processing are processes that can potentially generate fugitive dust. Regulations and legislations enforce the mining industry to use environmental monitoring systems, fugitive dust level measured by PM10 level as part of this. Air quality monitors are positioned at different locations around surface coal mines and track air quality levels during production. This study introduces a data-driven methodology to handle air quality issues related to fugitive dust at surface coal mines. Data is sourced from different mine equipment in real-time and they are integrated with air quality monitoring systems to provide information to support decisions for fugitive dust. The method is implemented and demonstrated in a case study at a large surface coal mine.

Sep 29, 2020

By Meng Li, Hao Nie, Weitian Ding, Mamdouh Omran, Ying Li, Yao Ge, Yaowei Yu, Abourehab Hammam, Lei Zan

This study examines the isothermal and non-isothermal reduction behaviors of iron ore compacts in a pure hydrogen atmosphere and compares the results obtained during the reduction process by CO. The different phases accompanying the reduction reactions were identified using X-ray diffraction (XRD) and its morphology was microscopically examined. In isothermal experiments, temperature plays a significant role in the reduction process. At any given temperature, the reduction rate during the initial stages is higher than that during the final stages. The reduction rate in H2 atmosphere was faster than in CO gas. The comparison of activation energy values suggested that reduction with H2 is more efficient thanwith CO. At the same temperature, the time required to achieve a certain degree of reduction was lower when using H2 gas than CO atmosphere. In non-isothermal tests, the heating rate has a significant effect on the reduction rate and reduction extent. At the same heating rate, the degree of reduction was higher in H2 atmosphere than in CO gas. Based on experimental data, the parameters of reaction kinetics were deduced by application of model-free and model-fitting methods. The reduction in H2 atmosphere was controlled by nucleation model (Avrami-Erofeev model), while the CO reduction reaction was controlled by gas diffusion.

Sep 29, 2020

By Ryan C. Stephan, Zach Agioutantis, Christopher Mark

During the past 15 years, roof fall rates have fallen dramatically in US coal mines, particularly in regions where the roof is weakest. The remarkable reduction in the number of roof falls has been accomplished with more effective roof support systems. The purpose of this paper is to present a design methodology that builds on and quantifies the basic roof support concepts that have been successful in the USA. The methodology starts by defining three modes of roof support, based on the roof strength relative to the stress level: (1) suspension, where roof bolts mainly provide skin control for strong roof; (2) beam building, where moderate strength roof can be supported by roof bolts alone; and (3) supplemental support for weak roof. Next, a large database of roof fall histories at a number of mines is used to define the approximate boundaries of these three regimes based on the coal mine roof rating and the depth of cover. Finally, guidelines are presented for site-specific design of support systems within each regime. The new computer package, analysis of mine roof support (AMRS), implements the design methodology.

Sep 29, 2020