Search Documents

By Andrelio Marcos Ribeiro, Lucio Ribeiro Camisao, Antonio Carlos Ataíde, Alan de Sousa Pereira, Renato Siqueira Campos

The annealing and pickling line n. 1, responsible for the production of stainless steel 3xx, 4xx and 430a in thicknesses from 4 to 0.4 mm, has two vertical strip accumulators. These are intended not to let the material exceed the determined time in the furnace and in the pickling, and consequently do not cause defects like burning and excessive pickling. Strip accumulator n. 1 avoids the line from stopping during welding execution of the coils in the welding machine. In sequence, the strip accumulator n. 2 avoids the line from stopping at the end cutting of the tips, and in the coils removal from the pickling. The strip accumulators have a roller table that during the strip accumulation moves vertically downwards while its counterweight moves vertically upwards, and do the inverse movement when the material is released. On December 12th 2018, the failure occurred in the strip accumulator n. 1, where it was verified that the shaft of one of the pulleys had been fractured by high-cycle mechanical fatigue, which was characterized by alternating bending. With the fracture of the shaft, occurred the unevenness of the counterweight that damaged the guides. Failure analysis of this occurrence was based on the PDCA methodology, when was verified a weld between the shaft and the pulley. The analysis of the microstructure transformation in the molten zone, in the heat affected zone and in the base metal was carried out in an optical microscope, and no abnormality was observed. It was also carried out the end test by penetrating liquid, finding an inadequate weld in its geometry, as well as longitudinal trunks along the center of the weld bead. However, after a huge investigation of the causes, it was found that the failure was triggered by an inadequate design of the pulley shaft. It was also verified that the shaft had an open measure, inadequate for the operational context. After the analysis, action plans were drawn up based on the FMEA methodology to inhibit the failure recurrence.

Oct 7, 2019

By Lucas Rosate Leite dos Santos, Erica Marcelino Freitas de Souza Silva, Glaucio Soares da Fonseca

Aços Inoxidáveis Austeníticos (AIA) são largamente utilizados não somente por sua boa resistência à corrosão, mas porque eles são amplamente conformáveis, fabricáveis, duráveis e soldáveis por praticamente todo os processos. À temperatura ambiente, as ligas homogêneas forjadas são, em geral, completamente austeníticas. Entretanto, para muitas aplicações essas ligas necessitam ser submetidas a processos metalúrgicos como a soldagem, que por sua vez pode causar modificações microestruturais. Desta forma, uma liga que antes era completamente austenítica pode apresentar frações de ferrita- δ retida. O presente trabalho investiga a influência do aporte térmico na evolução da microestrutura de solda do AIA 316L submetido à solda similar em dois diferentes aportes térmicos pelo processo TIG Autógeno. A análise microestrutural das amostras soldadas, foi realizada via Microscopia Ótica. Os resultados possibilitaram concluir que o aporte térmico de fato influenciou na microestrutura final do 316L, pois após a soldagem, para ambos aportes aplicados, a microestrutura foi composta de austenita e ferrita-δ e não apenas predominância da austenita como inicialmente apresentava o Metal Base.

Oct 7, 2019

By Guilherme Vitor de Araujo, Igor Cuzzuol dos Santos, Loyslene Rabelo Fernandes, Gustavo Henrique Sousa, Athos Fernandes Araujo

O desenvolvimento de nanopartículas magnéticas vem recebendo bastante atenção de pesquisadores devido a sua potencial aplicação em diferentes campos tecnológicos, principalmente em microeletrônica e medicina. A magnetita nanoparticulada é particularmente atraente para estas finalidades, pois apresenta comportamento superparamagnético, biocompatibilidade e resistencia à oxidação. Neste estudo foi avaliado a síntese das nanopartículas pela coprecipitação. Para isso foi observado a influência da razão molar de Fe+2/Fe+3 e da variação de concentração de NaOH na nucleação e precipitação das partículas. Sendo possível, determinar os melhores parâmetros para obtenção das mesmas e garantindo as suas propriedades. Para a constatação estrutural, a caracterização das amostras foi realizada por difração de raios X (DRX). A razão molar de Fe+2/Fe+3 se mostrou uma variável importante, em razões muito pequenas o resultado obtido foi goetita, enquanto a síntese a partir da razão 0,5 observou-se apenas a magnetita. E a variação da concentração de OH- teve influência no tamanho das partículas nucleadas, no qual menores partículas foram obtidas em meios mais básicos.

Oct 6, 2019

By Jovanir Francisqueto, José Fagundes, Nayara Neves Coutinho, Marco Túlio Costa

The purpose of this project is to increase the visibility of which will be daily produced on the hot strip mill (HSM). The forecast was performed through the implementation of an automated tool for weekly HSM production planning. The project was started with the definition of the weekly planning process, through the determination of the main business objectives, like as: priorities of service (customers and delivery date), definition of HSM’s rules and restrictions of operating resources. Using a sophisticated mathematical model, through the computational simulation is possible the experimentation of various production scenarios, allowing the visualization of volumes by type of sequence, clients / priorities, mix to be produced, cylinder change quantity forecast, better forecasting of the productivity of the HSM, consumption of utilities, within others. Main benefits: sequencing which production orders should be produced, reducing unforeseen stops due lack of material, improving the quality of the stock which allows the reduction of the aging of slabs in the slabyard and the vision of customer services. Computational simulation as a weekly planning tool achieve, with other benefits, to present alternatives for better decision making.

Oct 6, 2019

By Lóren Kelly de Paula Inácio, Witor Wolf, Renata de Oliveira Melo, Dagoberto Brandão Santos, Graziele Gianini Braga Maria, Nayara Aparecida Lopes Viana

Os aços inoxidáveis duplex combinam as propriedades mecânicas da ferrita com a resistência à corrosão da austenita. Quando submetido a tratamentos térmicos, pode haver precipitação de fases secundárias que prejudicam a resistência mecânica e à corrosão. O objetivo desse trabalho é avaliar a ocorrência de fases secundárias em um aço inoxidável duplex 2205 de grão ultrafino laminado a frio e submetido a temperaturas de recozimento de 600°C a 950°C por diferentes tempos (300-86400 s). Para identificação e quantificação das fases, foram utilizados microscopia eletrônica de varredura, difração de elétrons retroespalhados e difração de raios-x. As propriedades mecânicas foram avaliadas através de ensaios de tração e teste de microdureza Vickers. A presença de fase  e  foi observada junto ao carboneto de cromo, M23C6. A fase  foi confirmada apenas depois do tratamento à 800°C. De modo geral, o aumento do tempo de recozimento leva à uma maior precipitação das fases secundárias. À medida que a precipitação ocorreu, houve aumento da fração volumétrica de austenita e redução da fração de ferrita. Embora a resistência mecânica tenha aumentado, no geral, as propriedades mecânicas, como ductilidade, são prejudicadas pela precipitação.

Oct 5, 2019

By Ivan César Lopes Diniz, César Romero Afonso Goulart Júnior

Mandrels are tools applied to manufacturing seamless tubes. In VSB plants (Vallourec Soluções Tubulares do Brasil), it is used in two mills. Mandrel and PQF Mills. This is an expensive tool due its alloy (hot work tool steel – AISI H13) and lengh (between 12 meters and 22,5 meters). An opportunity to apply mandrels from PQF in Mandrel Mill has been identified. However, mechanical properties of PQF mandrels must be improved. This work presents the heat treatment process of Quenching and Tempering developed internally at VSB to improve PQF mandrel properties aiming to achieve Mandrel Mill requirements. Hardness and metallography tests were performed before and after some steps of the heat treatment to characterize and validate the process.

Oct 5, 2019

By Ivan César Lopes Diniz

Stretcher Reducing Mill (SRM) is a mill used in production of tubes. It is composed with a set 24 of stands responsible to define the final outside diameter (OD) of tubes. External appearance is critical in this process even though this requirement has no effect on mechanical properties. For this reason, an investigation of external longitudinal marks mechanism is in progress using 6 Sigma methodology. This paper is a part of the investigation with focus on the rolls and its mechanical properties. Destructive tests were performed in the rolls and compared with the project. After a detailed investigation, it was concluded that rolls were out of hardness specification and the project was poor of information. A new supplier was developed (internal market) based on the new project and all requirements were achieved as demonstrated in this paper. A monopolistic market for this product in VSB (Vallourec Soluções Tubulares do Brasil) was eliminated. Concerning the effect on the external longitudinal marks, the new rolls developed within hardness range minimized the mechanism of wear on rolls surface and consequently on tubes surface. A collateral effect has been faced, but still better than external longitudinal marks on tubes surface. The quenched and tempered rolls are more sensitive for process variation, mainly linked with cooling system and temperature of tubes (mechanical resistance for deformation). Nevertheless, a new material has been aimed focusing on reduction of rolls breakage with good tenacity and affordable cost.

Oct 4, 2019

By Felipe da Silva Siqueira, Weslley Luiz da Silva Assis, Gláucio Soares da Fonseca, André Luiz Moraes Alves, Guilherme Dias da Fonseca, Paulo Rangel Rios

Com o contínuo advento dos materiais aumenta-se as chances de uma dada transformação envolver duas ou mais fases produto. Quando essa transformação de uma fase matriz em duas ou mais fases produto ocorre, ela pode ser simultânea, quando as fases produto iniciam-se no mesmo instante, ou sequencial, quando elas iniciam-se em tempos diferentes. É sabido, pela teoria clássica da nucleação, que a nucleação heterogênea tem vantagens sobre a nucleação homogênea, e que vários sítios podem se tornar preferenciais por favorecerem a nucleação heterogênea. Dois sítios preferenciais bastante presentes são a interface de precipitados e os contornos de grão. Neste contexto, um modelamento analítico e computacional, via cone causal, foi empregado para investigar transformações simultâneas e sequenciais que possuem sítios preferenciais para a nucleação. Considerou-se que uma fase matriz policristalina que possui precipitados esféricos transforma-se em duas fases produto, 1 e 2, onde a fase produto 1 nucleou na interface matriz/partículas e a fase produto 2 nos contornos de grão. Os resultados de simulação tiveram ótima concordância com o modelamento analítico e observou-se que cada sítio preferencial teve um efeito muito distinto nas microestruturas simuladas.

Oct 4, 2019

By Wellington Ribeiro Moreirar, Anderson Willian Henrique Santini, Lívia Mara Cândido, Adriano Raimundo Totour

Rejects generated in mining projects usually do not have associated economic value. Most of the ore beneficiation processes occur by wet process with a higher fraction of water and ultrafine granulometry, which makes it difficult to dispose of these wastes. In 2013, studies with new tailings treatment and filtering technologies were initiated with the objective of eliminating the disposal of the residue generated in the industrial process to wet in dams. In this context, we tried to evaluate an alternative for the dewatering of the sludge and the tailings, aiming at their disposal in piles. Essentially, we sought to consolidate the application of the high-pressure filtration technology for the effluent dewatering, in order to allow its transport and its disposal in a sustainable way. The studies performed in a pilot filter showed good performance and allowed the industrial implantation. The studies and geotechnical indications of composite tailings (flotation and sludge) make it possible to dispose of the tailings in piles due to their better values of humidity, which allows them to be safely stacked.

Oct 3, 2019

By Rosa Malena Fernandes Lima, Rodrigo Fina Ferreira

Since 2011 mineral cargo shippers shall comply with the Maritime Solid Bulk Cargoes (IMSBC) Code regulatory framework, established by the International Maritime Organization. Some mineral cargos may liquefy during passage, under certain conditions, if the moisture content is beyond a certain level, and the cargo shifting may jeopardize the stability of the vessel. For cargos which are susceptible to this phenomenon the IMSBC Code stablishes that the moisture content shall be below the Transportable Moisture Limit (TML) for safe transportation by sea. Iron ore fines TML can be determined through the Modified Proctor/Fagerberg Test for Iron Ore Fines. Knowledge related to the TML has become essential to shippers, and research works related to this parameter are increasingly frequent. However, the typical daily productivity for having a TML result through this method is one up to two samples per executant person, requiring approximately 50 kg per sample. This study presents a practical example of the application of a prediction model for estimating the TML. The model application reduced substantially the laboratory work and sample quantity requirement for obtaining conclusions related to the TML.

Oct 3, 2019

By Jaiza Bernardo de Oliveira, Iasmim Ariane Silva, Pedro Henrique Medeiros Câmara

The process of manufacturing pig iron in the blast furnace industrial units has the consequence of the generation of slag, a waste that can be produced in high quantity and present damages to the environment, when not reused. In the composition of this tailings, it is sometimes possible to find the presence of metals harmful to nature, such as manganese, which has an important and widespread utility in the metal industries, but still, the slag ends up not being used as a potential source of this element. Knowing this, the slags were subjected to crushing and grading steps to separate the aliquots. These were applied in the tests of technological characterization of the material, from MEV, EDS, Soxhlet and analysis of liberation degree by digital microscope, finding data of several analyzes. Having said that, the objective of this paper is to demonstrate, through the characterization of the slag, that this material has in its composition metallic elements, focusing on manganese, that can be reused in order to avoid the generation of environmental liabilities harmful to the environment. The results show a manganese content with a degree of release greater than 80% in bands from 48 #, which were divided by density and thus allow the gravimetric separation of the material in question.

Oct 3, 2019

By Otávio da Fonseca Martins Gomes, Renata Hiraga de Vasconcellos Cruz

Maghemite is a mineral formed from magnetite oxidation at low temperatures, an intermediate term of the magnetite-hematite series. Maghemite could be misidentified as magnetite by X-ray diffraction, and/or as hematite by spot chemical analysis. Nevertheless, non-stoichiometric magnetite was detected and quantified in samples of Brazilian soils and iron ores by the Rietveld method refinement of its structure. The results were confirmed by optical microscopy and Raman spectroscopy, thus validating the method. X-ray diffraction with the refinement of the isomorphic substitution of Fe2+ by Fe3+ along the magnetite-maghemite solid solution could help to suitably characterize maghemite in iron ores.

Oct 3, 2019

By Aaron Samuel Young, Hiago Antunes Amador de Oliveira, William Pratt Rogers

Low commodity prices and lack of new high-grade deposits are pushing the mining industry for innovation. Lean mining has been vastly discussed in the past decades as a way to continuously improve mining efficiency. Although very theoretical, lean mining presents a set of new solutions enabled by the digital transformation that the mining industry is going through. This paper proposes a framework for a short interval control system with the purpose to allow timely responses by front line supervisors upon operational deviations. In the first part, the author briefly reviews concepts of short-range planning and lean mining. Then, the materials and methods used for the development of the short interval control system are discussed. Finally, alpha trial results are presented, and next steps discussed.

Oct 3, 2019

By Anivaldo Chevane, Leonardo Xerinda, Rogério Sendela, Andre Vilanculos

Moatize Coal Mine is located in Tete Province, in centre of Mozambique. The deposit contains Gondwana allochthonous coals, and has a large amount of mudstone and siltstone banding. Phosphorus levels in the coal can be high which impacts the use of the coals in steel making where phosphorus is considered a contaminant. The Chipanga seam in the Moatize deposit shows considerable variability, vertically within the seam and laterally across the deposit. The data available from the exploration work indicates that the phosphorus is predominantly present as Apatite but the Crandallite minerals also are significant. The concentration of phosphorus varies with coal particle density with the highest phosphorus levels found for the mid density coal which also shows the highest likely levels of apatite or fluorapatite. Crandallite minerals show higher potential concentrations in the Lower density coal..

Oct 3, 2019

By Flanelson Maciel Monteiro, Yago Lutz Castro Pinto, Marcondes Mendes de Souza, Mauro Froes Meyer

In Potiguar West, in the regions of Vale do Açú, Mossoró, and Chapada do Apodi there are limestone outcrops of about 20 thousand square kilometers (with a thickness ranging from 50 to 400 meters). Limestone is an essential raw material for the manufacture of agricultural products and especially for construction. The rock serves for various productions, among them is used for the production of cement, lime, fertilizers, even ornamental rocks. Thus highlighting the mineral potential in the state of Rio Grande do Norte, as well as its use in the production of various products.

Oct 3, 2019

By Homero Delboni Junior, Thiago Nunan, Flávia Vargas

Ball mill liners perform two main functions in grinding process: protect the mill shell from the aggressive milling environment and delivery input power to the charge. When it comes to liners optimization the challenge are to prolong the service life and improve grinding performance. Some liners characteristics such as A / B ratio, lifters number, lifter height, and attack angle are extremely relevant to grinding process. By analyzing process data, and through DEM simulations application, these parameters were improved on W-mill liner, located at Vazante concentration plant. The new profile promoted a reduction of power variability between the final and the initial life cicle intervals and, therefore, better stability to circuit operation. In addition, the new liner service life reached 21,603 hours, 25% higher compared to the previous one in use. This optimized profile therefore proved to be able to improve its functions by achieving superior process performance combined with longer service life.

Oct 3, 2019

By Rudi César Comiotto Modena, Gabriel de Castro Moreira, Diego Machado Marques

The definition of geological/geostatistical domains is the first step in building a mineral resource model. A suitable division for these domains requires some prior knowledge about the deposit geology and can be supported by a careful statistical analysis. It is crucial that data with similar characteristics are grouped together, to avoid the mixing of statistical populations, defining the so-called stationary domains. In order to assist in this definition, two unsupervised clustering algorithms were applied: Otsu and K-means. The first one is widely used in image segmentation and it is based on the exhaustive search of the data to determine the best threshold for separating them. K-means is one of the most used techniques in machine learning, and it is based on the iterative analysis of the statistical distribution. Clustering algorithms may present some shortcomings when applied to geological data, since they are based on pure statistical analysis, not considering spatial distribution or data location. Choosing the most appropriate number of domains can also be challenging. Some methods for defining the best number of groups are presented, based on the analysis of variances between/inside groups, supported by indicators variography in order to verify this definition.

Oct 3, 2019

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Beatriz Peralta Oruê

Manganese, a toxic mineral, related to manganism may have high added value for the steel industry. The difficulty in obtaining manganese encourages the exploration of new secondary sources such as the lateritic nickel effluent. In Brazil, nickel reserves are predominantly lateritic, making the country a potential producer. For the tests, a synthetic solution was used which simulates the lateritic nickel effluent from leaching. The oxidative precipitation with ozone occurred at the oxygen flow rates: 0.5; 1.0 and 2.5L/min, at the original pH 1.5 at 21°C in a 500 mL bubble column reactor. O3 was produced in the benchtop generator feed by 99% oxygen. The ozonation time was determined by the oxidation potential1.55V. The ozonated solution was centrifuged and filtered. The filtrate and collected samples were characterized in ICP-OES. Optimization tests with ultracentrifuge were performed. The best precipitation reached 97% at 0.5L/min O2 at 6.07 ± 0.045mg/min of O3 dosage and resulted in a solution 10-15mg/L Mn+2, above 1mg/L, maximum value acceptable by Conama 2011, to be retreated before being discharged into the water body or being reused as a manganese source.

Oct 3, 2019

By Vitor Vianna de Castro Moreira, Danilson Gonçalves de Melo e Silva, Gabriel Augusto da Fonseca

The present work aims to describe the changes made in the operational procedure of the reheating shell furnace, of the hot-rolling of seamless tubes line at Barreiro Plant of VSB, during non-production periods, focusing on reducing natural gas consumption. According to the previous procedure, the furnace was kept at 750°C on these periods, using the main burners. With the new procedure, the furnace is naturally cooled, maintaining only the auxiliary burners with a pilot light turned on, without worrying about the conservation of temperature. Subsequently, the furnace is heated with a rate of 150 ºC/h until it reaches the setpoint temperature of production. This procedure change was successful and didn’t cause operational and security problems. The minimum stoppage time needed for the natural cooling to be economically favorable is 6 hours and 30 minutes. The new procedure reduced the natural gas consumption in 4.500 Nm³, considering 24 hours of stoppage, achieving an estimated annual economy on the thermal energy costs of R$440.000,00 in 2019.

Oct 3, 2019

By Humberto Almeida de La Serna, Kayleigh Meneghini, Gabriel Rubio Pirillo, Maurício Guimarães Bergerman

The Mining Annual Report (RAL) is an obligation for every current owner of a brazilian mining process which is already undergoing extraction. This document is basically composed by the company’s annual book balance, where is possible to educe informations that allow to evaluate the mineral market behavior. This research gathered filtered data linked with RAL production and technical responsability between 2010 and 2017, gotten by the Information Access Law, without the real CNPJ of each company, in order to preserve their identity. The results allow to quantify the Brazilian mining production during the period, illustrating that approximately 46% of the companies can be classified as micro, 30% as small, 20% as medium and 4% as large mining companies. It was observed that the micros concentrate the most part of technical responsibles who sign for more than three mines.

Oct 3, 2019