Search Documents

By José Francisco Cabello Russo, Késsius Bortolan Menezes, Henrique Dias Gatti Turrer, Denílson Rodrigues de Araújo

With the start-up of the Minas-Rio system, Anglo American, in Conceição do Mato Dentro, MG, in 2014, a methodology was also implemented and certified to perform the tests to obtain the results of TML (Transportable Moisture Limit). Such a parameter provides the maximum moisture content contained in the material that could be transported without the risk of the cargo liquefaction process, which could lead to incidents such as the tipping of ships carrying iron ore concentrate in bulk on the deep water. This means that when loading a ship, the moisture content of the material to be transported should not be higher than the TML reference value, obtained in a physical test and intrinsic to the material. Should this occur the charging may be rejected. From 2014 a downward trend was observed for this reference parameter in the Minas-Rio system, with results approaching the moisture of the filtered product, bringing risks to the operation of the project. In this way, an investigation of the possible causes for understanding this downward trend was required.

Oct 3, 2019

By Leonardo Camilo dos Reis, Edmilson Fernandes Dadomi, Claudio Silva de Paulo

In the hot strip mill production, one of the factors that may affect the productivity is the occurrence of failure due to the geometry of the strip at the exit of the rolling mill, because the tip of the strip can turn-down or turn-up. This study had the objective of evaluating the behavior of the strip when leaving the working rolls, through numerical simulation, aiming to know the influences of the main variables that govern the formation of the turn-down. The methodology consisted in performing the computational simulation of the strip mill and to vary the operational and geometric parameters that could influence the process. The results showed that the rolling of hot strips of HSLA material with final thickness varying between of 3 to 6 mm and a reduction of 6.6% to 11.0% in the last stand of a hot strip mill, tends to bend towards the roll with larger diameter, higher friction coefficient , higher temperature and lower limit of material flow. It was observed that the variation in diameter is the main factor that contributes to the formation of the curvature of the front-end of strip. Based on these results, several measures were implemented in the industrial line, with a significant reduction in the occurrence of turn-down.

Oct 2, 2019

By Antônio Donizetti Giuliano, Fernando Codelo Nascimento, Viviane Tavares de Moraes, Cilene Cláudia Diógenes, Erivan Cardoso Rocha

Nos lagos ornamentais geralmente tem-se a dificuldade em controlar o crescimento de algas, pois existe a incidência de luz e a disponibilidade de nutrientes provenientes da ração fornecida aos peixes, os quais propiciam o crescimento e o desenvolvimento das algas. Uma alternativa de tratamento é o processo oxidativo avançado (POA) existente, a ozonização, com o objetivo de propor um processo de tratamento de água para controlar a proliferação de algas em um lago ornamental sem prejuízos à comunidade aquática, vivente no lago. A metodologia utilizada foi o estudo de caso do lago que envolveu as seguintes etapas: construção do lago ornamental; definição do sistema de tratamento; monitoramento de parâmetros como: a demanda bioquímica de oxigênio (DBO), a cor, o pH, a temperatura, a amônia (NH3) e o oxigênio dissolvido (OD) do lago durante três meses; aplicação do ozônio para controlar a proliferação de algas e monitoramento dos mesmos parâmetros durante o processo de ozonização. Dentre os principais resultados encontrados citam-se: a redução de 170 unidades de Cobalto platina (PCU) da cor esverdeada da água do lago; descimento de 60% da DBO; aumento de 16% da concentração de OD e a redução de 80 a 100% da concentração de NH3, eliminando assim odores desagradáveis e melhorando a qualidade da água. Por meio dos resultados obtidos conclui-se a aplicação de ozônio em lagos ornamentais é uma alternativa para a manutenção aquática e melhoria da qualidade da água..

Oct 2, 2019

By Z. Zhang, M. S. Gonzalez, M. de P. Bueno, P. Holopainen, S. Luukkanen

"Despite being a field of study that requires practical knowledge and experience, mining engineering education follows the same pattern in most mining universities around the world, consisting of theoretical courses and laboratory-based practical modules (Mischo, 2015). The possibility of having practical training in real mining conditions on actual mine sites or processing plants is limited, while the only contact that undergraduate students have with mining operations during their time of study is usually through shorttime internships or visits in the context of educational trips. Real integration between universities and the mining industry may be scarce, which does not help students to observe the actual processes and thus understand the whole picture of mining operations.Indirect practical training is now possible since that technology is shifting from mechanical to digital, and the use of virtual reality — in the context of Mining 4.0 — can provide additional experience to the learning process. However, virtual reality is limited to the visual impression and is also limited in actions (Binder et al., 2018). In any case, when there is not a proper pragmatic view of how the different disciplines link to each other, especially if there is a lack of communication, unfortunately the results could be seen at a later stage in the mines as a poor performance of professionals and workers.Another major challenge for educating specialists in the mining sector is that experimental mines suitable for practical education, where the skills and knowhow could be developed and/or enhanced, are rare worldwide. Such research and educational (R&E) facilities are practically former metal ore mines that have been transformed into experimental sites. Besides being limited in number, not all facilities of this kind serve both a research and educational purpose.An early example of asolely experimental mines is the Luossavaara-Kiirunavaara Mine site operated by LKAB in Sweden, where systematic research on rock mechanics and mining engineering was successfully carried out in the 1980s. As a result, the developed underground mining technology was applied in LKAB’s mines at a later stage. There have also been research mines within collieries such as the former Lake Macquarie Mine at New South Wales in Australia and the Zeche Tremonia Mine in Germany), but these are no longer in operation (Mischo, 2015)."

Oct 1, 2019

By William Gleason

"It has been more than 10 years since Montana Resources’ copper/molybdenum mine has had a lost-time injury at its site in Butte, MT. With more than 350 employees and an average production of about 15.5 Mt/a (17 million stpy), which includes 29.5 kt (65 million lbs) of copper and 4 kt (9 million lbs) of molybdenum, the mine’s journey to a decade of exemplary safety is an impressive feat that has required hard work, commitment and, most of all, leadership from every level of the operation.It has not always been an easy journey, nor has it been one without scrapes and bumps along the way, but it is one that has produced stellar results. Mike McGivern, vice president of human resources, and Pete Steilman, safety manager at the mine, spoke with Mining Engineering about how the operation transformed from a site that was accustomed to collecting citations for safety violations to one that is now collecting awards for its safety record.Simply put, Montana Resources has made safety a value and the people its top priority.The operations faced many predictable challenges in 2003, when the mine was being brought back online after three years of sitting in care-and-maintenance status. It had been shuttered in 2000 because of low commodity prices and high operating costs, and, in the three years that the mine was idled, the equipment became dilapidated, and some of it was no longer in compliance. Less than half of the workforce returned to the site for the restart, and the team was challenged with getting the gears turning again to produce copper and molybdenum. But the most daunting challenge of all of was keeping the workforce safe during the transition.In the first few years of operation the mine racked up citations from the U.S. Mine Safety and Health Administration (MSHA) at an alarming pace, so much so that in May 2006, Montana Resources received a letter from the MSHA District Office informing the company that the operation was being placed on the Potential Pattern of Violations list due to its excessive citation history and high rate of significant and substantial citations. It was clear that something significant had to be done to change the course of action at the mine."

Oct 1, 2019

By Steve Zaffron, Olga Loffredi, Eric Seedorff, Mary Poulton

"The New Face of Mining is a recognition of the central role of human beings in mining and the underappreciated power they can have in generating breakthroughs in business performance and shareholder value. The key is people creating, aligning on, and subsequently enacting the future of mining. A methodology that is effective creates a corporate environment for alignment to be possible and then transforms operations by embedding the necessary behaviors, processes and practices. The people within the organization then are empowered to find and to implement solutions quickly, as measured business results demonstrate in case histories of diverse mining challenges around the globe and over the decades.Urgent case for actionThe physics of mining does not change fundamentally over time, but the context in which it operates changes rapidly, periodically requiring a new face of mining. “The New Face of Mining,” which has been used as a metaphor for the campus-wide mineral resources research organization at the University of Arizona, has many facets, including societal, generational, technological, financial and environmental, but at the center, always, is humanity. The New Face of Mining is not necessarily about age, it is about people first imagining and then creating a new future for mining. The challenges facing the global industry evolve from year to year and differ in individual companies or mines at any one time.Quantified outcomes from case studies indicate that a methodology, now also offered annually in a four-day, open-enrollment leadership program tailored to the mining industry, is effective at generating breakthrough results in the mining business. Such challenges range from those with important technical components to others that are mostly social challenges. Our focus, however, is the centrality of people in aligning on and enacting the future of mining. We use the phrase New Face of Mining for leadership and ways to empower people in organizations that commonly are overlooked in the mining industry. Some of the material in this article is based on the ideas of Werner Erhard and on the book by Steve Zaffron and Dave Logan (2009), The Three Laws of Performance: Rewriting the Future of Your Organization and Your Life.At Davos, Switzerland in January 1992, nine visionary mining chief executive officers (CEO) gathered to create the Global Mining Initiative. Much has changed in the 26 years since that meeting:• The world GDP has increased from US$25.4 trillion to $75.8 trillion.• The annual number of U.S. patent applications increased from 186,000 to 629,000.• The number of websites has increased from 100 to 1 billion.• The number of academic references to artificial intelligence has climbed from more than 16,000 to more than 1 million.• The number of cell phone subscribers grew from 11 million in the United States to four billion globally."

Oct 1, 2019

By Rafael Fernandes Reis, Leonardo José Silva de Oliveira, Rodrigo Seara Martins

Alterações na cristalização dos pós fluxantes durante o processo, devido variações de composição química pelas reações metalúrgicas na interface metal/escória ou pela incorporação de compostos exógenos, afetam o fluxo de calor no molde de lingotamento contínuo. Um dos compostos importantes é o ZrO2, proveniente do desgaste da válvula submersa. A proposta do trabalho foi investigar o efeito deste composto, utilizando simulação laboratorial, na cristalização do pó fluxante e no fluxo de calor do molde. Os resultados demonstraram que quando há o incremento do teor de ZrO2 o fluxo de calor na região do menisco também se eleva. Tal efeito é crítico para formação de defeitos, uma vez que a região do menisco é crucial para a solidificação inicial do aço.

Oct 1, 2019

By Marcelo Rebellato, Beatriz Pereda, Beatriz Lopez, Pello Uranga

The classical application of Nb microalloying in the development of thermomechanical processes for flat products has been related to its suitability to enhance strain-induced precipitation and get a pancaked austenite prior to transformation. As new steel grades or new lay-outs are being developed, more complex metallurgical conditions need to be evaluated. In this context, Nb microalloying, alone or combined with other microadditions, needs to intervene in a more controlled way in additional steps of the thermomechanical process, besides its conventional strain-induced precipitation role. For example, the hardenability enhancement associated with Nb to properly achieve lower temperature transformation products, demands a proper balance of the Nb amount precipitated during rolling and the one remaining in solid solution. Similar effects are also sought when the final available Nb is used to increase strength through precipitation hardening. This manuscript evaluates how changes in the rolling strategies affect the interaction between Nb(C,N) precipitation and austenite recrystallization at different steps of the rolling process. As the possible interactions between parameters intervening simultaneously are quite complex, the application of microstructural models helps to properly define the best austenite conditioning combined with the convenient amount of Nb in solution, as a function of the final property requirements. Along the manuscript, several strategies will be discussed for the case of hot rolling of flat products comparing both normal and coarse initial austenite grain sizes.

Oct 1, 2019

By Wellington Bruno Silva de Jesus, Esaú Gomes Souza, Luiz Gabriel da Silva Nascimento, Jeovan Ramos Nascimento, Deibson Silva da Costa

O estudo desse trabalho foi voltado para a solidificação unidirecional da liga Al-9%Ni usando um dispositivo em que sua câmera interna não permite a existência de gradiente de temperatura para outra direção que não seja o sentido da solidificação. Após o processo de fusão e solidificação foram coletadas amostras de posições aleatórias ao longo do lingote para serem realizados os procedimentos metalográficos, ensaio mecânico e microscopia óptica e de varredura. A macroestrutura se mostrou predominantemente colunar vertical, e a microestrutura se mostrou dendrítica nas regiões mais próximas a extração de calor tendo seu espaçamento cada vez menor, o que influenciou no aumento da dureza. Observa-se também através de análise de microscopia eletrônica de varredura a presença de uma grande quantidade de fibras de Al3Ni, que também contribuíram para o aumento da resistência da liga.

Oct 1, 2019

By Dagoberto Brandão Santos, Kairo de Barros Guimarães, Túlio Magno Füzessy de Melo

The effect of the cooling conditions on the microstructure and hardness of a Dual Phase hot-rolled steel 800 MPa strength was investigated. Simulations of the cooling conditions using a dilatometer were carried out from samples of a hot rolled coil with variations of the intermediary temperature from 620 to 740°C, isothermal holding time between 1 and 10 s and coiling temperature between 50 and 400°C. In addition, two CCT (Continuous Cooling Transformation) diagrams were developed to evaluate the effect of the isothermal holding time on the phase transformations of the remaining austenite. It was observed that the intermediary temperature has a strong influence on the kinetics of the phase transformation, as well as the isothermal holding time influences the amount of ferrite formed and, consequently, the final microstructure and hardness of the material. The coiling temperature did not cause significant changes in the amount and morphology of the ferrite, but a gradual replacement of martensite with bainite was observed, which, in addition to the self-tempering effect, contributed to the hardness reduction.

Oct 1, 2019

By Samuel F. Rodrigues, Clodualdo Aranas Jr., Fulvio Siciliano

The application of thermo-mechanical control processing (TMCP) in hot rolling of steels has become a common routine since the last 60 years. The understanding of the physical metallurgy behind TMCP played a major role in the early developments. Physical and numerical simulation works are performed firstly to derive the fundamental metallurgical knowledge and secondly to conceive existing TMCP practices. In this paper, a summary TMCP techniques is presented. The occurrence of dynamic transformation of ferrite in the austenite region is shown by means of synchrotron light diffraction methods. This phase transformation mechanism is taken into consideration and its effects on TMCP are proposed in an exploratory way.

Oct 1, 2019

By Xihuai Gong, Hongshuang Di, Jianping Li, Ning Yan

In this work, we investigated the effect of the rolling process (warm-rolled or cold-rolled) on microstructure evolution and mechanical properties of 9Mn steel. After intercritical annealing at 670°C for 10min, both cold-rolled and warm-rolled microstructures are composed of ultra-fined austenite and intercritical ferrite. The austenite in warm-rolled sample includes two types of morphology, namely equiaxed and lamellar, which exhibits a wide distribution of grain-size. The incomplete recrystallization or recovery behavior of ferrite in warm-rolled and annealed sample results in higher yield strength and shorter yield point elongation. Moreover, the warm-rolled and annealed sample extends the TRIP-related work hardening over a broad strain range, resulting in a better combination of ultimate tensile strength and total elongation.

Oct 1, 2019

By Stephanie L. Kaster, John G. Speer, Blake M. Whitley

Niobium-microalloying technology has been increasingly applied in a wide range of steel applications over the past half-century, to increase strength, control microstructure, enhance properties and enable a variety of applications. To achieve desired performance levels, thermomechanically processed microalloyed steels are widely supplied by the steel industry for high volume applications in hot-rolled plate, sheet and structural steels. However, in steel long products and forgings, the final properties are often generated by downstream users, after heat-treatment, surface hardening, forging or wire drawing. Two examples are presented highlighting advancements associated with Nb-microalloying, to enhance microstructures and properties developed during thermomechanical and/or downstream processing. In the first example, a 0.02 wt. pct. Nb addition was made to a medium-carbon bar steel intended for induction-hardening applications requiring fatigue and fracture resistance in bending and torsion. The Nb addition as well as thermomechanical bar processing led to beneficial refinement of both the pre-induction and post-induction microstructures. In the second example, a 0.01 wt. pct. Nb addition to a high-carbon wire rod was found to refine the pearlite colony size and interlamellar spacing, and increase the hardness.

Oct 1, 2019

By Daniel Andrade Paes de Lima, Gerson Evaristo de Paula Júnior, Beatriz Fausta Gandra

The gradual reduction of the sinter feed size has been a complicating factor in the maintenance of sintering productivity. In addition, pellet feeds have been used for chemical correction. Because of this, it is necessary an effective cold agglomeration step in sintering to keep the ironmaking competitiveness. Thus, in the present paper, four different technological routes for cold agglomeration with sinter feeds (drum mixer, intensive mixer + drum, double drum and HPS - Hybrid Pelletized Sinter) were evaluated in pilot scale and their impacts on the indicators of the sintering and the sinter quality was obtained. It was found that the best results on granulation index and, consequently, productivity were obtained in the route using HPS. However, the sinter from this process was the most fragile among the analyzed ones. The performance of the double drum process was superior to the intensive mixer from the point of view of productivity and sinter quality.

Oct 1, 2019

By Flávio Túlio Busatto, João Bosco Mendes, Marcio de Souza Lana, Raphael Dias de Medeiros, Gabriel Nazareth G. Alcoforado

The sintering process begins at the ignition stage of the surface layer of the mixture to be sintered. This ignition is performed through the heat supplied by a furnace, called "Ignition Furnace", and this burn must have sufficient heat potential to start the agglomeration process. As a result of the horizontal movement and the flow of air passing through the material, this surface firing front is transported until reaching the lower zones of the bed, thus producing the sinter. The higher the calorific value of the fuel used, the more efficient (lower fuel consumption and higher temperature) is the surface burning, thus raising the mechanical strength of the product during the process. Due to variations in fuel quality, keeping the ignition temperature controlled becomes a challenge, so, in this work, a study on the combustion of coke oven gas (COG) was carried out, evaluating not only its stoichiometric but also the most adequate control strategy, in order to maintain the working temperature and still optimize the yield and quality of the sinter produced. Mathematical knowledge, automation, control and industrial combustion were used in order to achieve the expected results.

Oct 1, 2019

By Jéssica Vicente Luiz, Rayander Martins Pimenta, Everton Pedroza dos Santos

The Hybrid Pelletized Sinter (HPS) is a agglomeration process that involves the combination of conventional sintering and pelletizing techniques and can be used with the purpose of obtaining improvements in the agglomeration stage of iron ore, and one of the great advantages of the process is the use of a wide particle size range of the ore. In this way, the superfines of low-cost ores, which are improper in sintering, can be used in the HPS process for the formation of the quasi-particle. The use of HPS with the sintering plants of the industries presented throughout the study, enabled an increase in productivity, decreased fuel utilization and reduced slag formation in blast furnaces. Thus, the present study aims to present a review of the literature on the Hybrid Pelletized Sinter (HPS) process and its main characteristics, as well as the results obtained by the companies that adopted the process.

Oct 1, 2019

By Jianping Li, Fei Peng, Yunbo Xu, Jiayu Li

In this study, in order to achieve ultra-high strength without reducing plasticity, a novel heat treatment involving a pre-quenching process prior to conventional intercritical annealing (P-IDP) was proposed in a low carbon low alloy DP steel. It revealed that abundant fraction of banded structure was observed after conventional intercritical heat treatment (IDP) due to the inheritance of cold rolling deformation. However, the banded structure in novel heat treatment was eliminated significantly, whilst the refined microstructure was relatively more homogeneous with ultrafine ferrite grains. Moreover, obvious chain-networked martensite grains along the ferrite grain boundaries were obtained. The optimum mechanical properties with ultimate strength of 1238 MPa, total elongation of 17%, product of strength and elongation (PSE) of 21GPa% were obtained by P-IDP treatment, which was much higher than the values reported with similar composition. As to pre-quenching treatment, all of grain refinement, homogeneous distribution of martensite islands and precipitated strengthening of microalloyed carbides were beneficial to improve the final strength and ductility.

Oct 1, 2019

By Cláudio Magno do Carmo, Gilmar Pinto Ribeiro, Luciney Miranda Martins

A rotina operacional e os seus processos de validação e acompanhamento já estão consolidados no ambiente da Tecnologia da Informação (TI). No ambiente da Tecnologia de Automação (TA) estamos avançando lentamente, apesar da grande semelhança em vários processos, devido a dificuldades de adaptação dos controles principalmente no tocante aos tempos de resposta e atuação das equipes. Enquanto a TI atua na garantia da execução do tripé formado por confidencialidade (segurança), integridade (precisão dos dados) e disponibilidade, rigorosamente nessa sequência de prioridades (CID) [1], a TA procura atender às necessidades da produção, e inverte a prioridade para a disponibilidade (DIC). Daí o conflito inicial entre os modelos: demanda imediata ou planejamento detalhado das atividades dentro dos padrões de qualidade da TI, entretanto sem impactar nas metas operacionais. É tudo uma questão de visão e principalmente de gestão por processos! Quais as diretrizes comuns? Quais os processos similares? Encontrar os pontos de afinidade, alinhados com as expectativas dos gestores e com foco na disponibilidade, sem perder a integridade e confiabilidade dos dados é o desafio.

Oct 1, 2019

By Gilberto Fernandes Lima, Leonardo Neves, Getúlio Fonseca dos Santos

O refino secundário é um processo onde a homogeneização do aço e as flotações de inclusões ocorrem no banho metálico, cujo conhecimento do tempo de mistura é necessário na produção de aços limpos. A panela, principal vaso onde ocorre o processo, contem plugues ou bicos de injeção de gás inerte, podendo ser utilizados argônio ou nitrogênio, que são responsáveis pela rinsagem do aço. Devido à importância desta etapa neste processo, este trabalho objetivou realizar o estudo do escoamento bifásico do aço na panela com duas configurações diferentes, sendo a configuração um com dois plugues de gás inerte: ambos a meio raio e a configuração dois com dois plugues de gás inerte, um a meio raio e outro no centro da panela. Neste projeto foi utilizada fluidodinâmica computacional, CFD, para a realização das malhas e simulações que forneceram as curvas de traçador e o perfil de velocidade para ambas as configurações. Os resultados simulados indicam que a configuração dois é a mais indicada para o escoamento bifásico, sendo a melhor opção para ser utilizada no modelo de panela industrial.

Oct 1, 2019

By Roberto Parreiras Tavares, Leonardo José Silva de Oliveira, Marcelo Moreira Furst Goncalves, Rodrigo Seara Martins

Os pós fluxantes estão continuamente sendo desenvolvidos para permitir que o processo de lingotamento contínuo possa gerar produtos de melhor qualidade superficial. Entretanto, a seleção e a avaliação do desempenho industrial desse insumo não são simples por envolver o conhecimento simultâneo de várias propriedades físico-químicas. Nesse sentido, desde que medido de forma adequada, o consumo do pó fluxante no molde é uma ferramenta útil para avaliar a estabilidade operacional. Assim, foi desenvolvido um sistema para quantificar o consumo específico dos pós fluxantes no molde para posteriormente correlacioná-lo com eventos que possam levar a desvios de qualidade superficial do produto lingotado.

Oct 1, 2019