Search Documents

By P Corbett, P Sheffield

Springvale Mine is an underground coal mine in the western coalfield of New South Wales which utilises retreat longwall mining technique. The mine encountered significant gateroad floor heave issues during retreat of LW415. Floor heave has subsequently impeded longwall advance as well as longwall bolt up and recovery to some extent during the extraction of the next five longwalls. Floor heave at Springvale Mine develops throughout the lifecycle of the mine roadways, and is most prevalent in longwall gateroads. Floor heave has been measured as early as 2 weeks after roadway development and continues to develop through the post-development phase, with a rapid increase in close proximity to the longwall face. This paper presents a case study of the evolution of understanding of floor heave behaviour at Springvale Mine based on geotechnical characterisation, an intensive convergence monitoring program (roof and floor movement) and spatial correlation of monitored locations with longwall face position. The analysis considers previously known factors contributing to floor heave including mining depth, geological and physical properties of the rock mass and mine design geometry. Investigation results indicate a strong correlation between floor heave magnitude and roof dilation magnitude, geophysically inferred faulting in underlying strata, areas of localised stress concentration and mine roadway dimensions. This paper also discusses the predictive model which was developed as a result of the study, which is now the basis of the floor heave removal program used to manage roadway convergence at the mine. Floor heave monitoring, prediction and management strategies (including floor reinforcement and removal) are also discussed. CITATION:Sheffield, P and Corbett, P, 2018. Managing floor heave in an underground longwall coal mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 78–94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By A Vakili, F Harvey, H Greaves

Mine seismicity is one of the most difficult geotechnical risks to manage in seismically active mines. There are currently some established empirical and statistical methods that provide quantitative measures for seismic hazard assessment in operating mines. However, these methods are mostly suitable for quantifying the current or historical seismic hazard and often cannot be directly used to forecast the future hazards. Numerical modelling is the only analytical tool that can capture the level of complexities required for a meaningful analysis of mine seismicity and therefore to facilitate a reliable forecast of future hazards. However, there is currently no widely accepted and established guideline and methodology for analysing and forecasting mine seismicity using numerical modelling. This paper first provides a background on previous published studies on this subject and then outlines the key aspects that can affect the reliability of the forecasting for mine seismicity. These aspects include a) processing of historical seismic data, b) selection of suitable numerical modelling approach, c) Post-processing and interpretation of the model outputs. A case study is then presented for the Gwalia Deeps Mine where a new framework was developed to forecast future mine seismicity. High-quality seismic data for a period of five years was used for back-analysis and comparisons with the numerical modelling outputs. After development of the method, the future seismicity was forecast for the next 12 months and the actual seismicity was monitored against the forecast during this period. Results of this study shows promising potential for the proposed framework to be applied more routinely and at other mine sites. However, more validations are required at Gwalia Deeps mine as the mine proceeds to deeper levels. In addition, the method needs more improvements and should be tested and validated at other mining operations before it can be established as a proven method. CITATION:Vakili, A, Harvey, F and Greaves, H, 2018. Forecasting mine seismicity – towards a more established methodology, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 207–222 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By X Feng, X Zhang, W Sun, Y Zhe, K Hou, B Zhao, H Liu

Pulang Copper Mine, being China's largest newly built mine using block caving, boasts an annual production capacity of 12.5 million tons. Production level and roadway stability hold the key to the successful application of block caving. However, with Tong Kuangyu being the only mine in China which has applied such a method, we currently lack relevant experience in the successful application of the method. This paper has studied the influence of different rock mass zonings, fault thickness, fault dip angles, on-site construction quality on the production level, roadway stability of block caving through numerical simulation and analysed the roadway stability in different kinds of support solutions so as to ensure the successful application of block caving in Pulang Copper Mine. The results have shown that the existing support method in Pulang Copper Mine can meet the requirement of roadway support in zone II and III, but could not satisfy the demand in terms of support strength in the relatively fragmented zone I area. When roadway passes through the fault, the deformation of surrounding rock and plastic zone of roadway will gradually decrease with the increase of fault dip angle; the deformation of surrounding rock and plastic zone of roadway will gradually increase with the increase of fault thickness. An ideal support effect can be achieved through the joint support of grouting and bolting when roadway passes through the fault. In the measured model of on-site construction, there is stress concentration in the intersection between the access and transverse drift of ore removal. Therefore, the stability of the roadway can be improved by improving the construction quality. CITATION:Sun, W, Hou, K, Zhang, X, Feng, X, Liu, H, Zhe, Y and Zhao, B, 2018. Research on supporting technology for production level roadways of block caving in Pulang Copper Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 95–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By J Morgan

Regular monitoring of surface deformation over mine sites is important for providing updated information to managers regarding geotechnical risks related to ground instabilities. This is particularly true in cases where unexpected or accelerating movement patterns are observed, as these trends may have implications related to worker safety within active mining environments, as well as continuity of ongoing operations. InSAR is an active remote sensing technique that uses radar satellite imagery to precisely measure ground movement. This technology has started to become a standard tool for monitoring surface stability in many different sectors, including underground and open pit/cut mining applications. In recent years the launch of satellites that collect radar imagery on a more frequent basis, coupled with advances in InSAR processing techniques, has improved both the extent to which movement patterns typical of mining operations can be characterized and the temporal scale on which results can be reported to geotechnical departments. As a result of these developments, InSAR monitoring can now better meet the operational needs of mine sites. An overview of the more recently launched satellites that have a particular relevance to the monitoring of mines is provided, along with an explanation of the InSAR tools that are the most valuable to mine managers and geotechnical engineers. First, broad differences between high resolution X-band imagery and low resolution (but freely available) Sentinel imagery are discussed. Second, the various InSAR tools and their particular applications for different types of mine sites and operations are covered, which include fast delivery deformation maps for short-term reporting, multi-interferometric algorithms for longer-term analyses and rapid movement tracking (RMT) for emergency monitoring or high-risk situations. The ability of the technology to resolve 2D and 3D movement is also touched upon. Practical examples of InSAR application over a variety of mine sites will be presented, as well as surrounding hazards including landslides, to illustrate how InSAR can help provide geotechnical engineers with a picture of surface stability over the full mine site and surrounding areas to help manage risk. CITATION:Morgan, J, 2018. Wide area mapping of ground instabilities from space: InSAR for geotechnical risk assessment and hazard monitoring, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 375–382 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By M Robotham

In April 2013, Rio Tinto Kennecott Copper’s (RTKC) Bingham Canyon mine experienced what is arguably the world’s largest ever in-pit slope failure. The failure initiated along a major, continuous, low-strength bedding fault, named the Manefay bed, and comprised approximately 145Mtonnes of rock and waste dump material. Initial East wall slope deformations were detected some months prior to catastrophic slope collapse by RTKC’s slope monitoring systems. However, the failure mechanism was different to that which had historically been experienced in the prior more-than-100 years of open pit mining. Failure occurred as two separate events, the initial one likely consisting of a frictional failure of rock materials along the Manefay bed itself, before a second phase of failure occurred, which included a large mass of old rail dump material. The combination of these events led to a much larger failure run-out than had been anticipated by the RTKC team which led to loss of, and damage to, mining equipment and infrastructure as well as significant interruption to mining activities. Due to the diligent monitoring of the slopes no safety impacts were experienced at the mine, and as such the details and learnings from this failure can readily be shared with the broader mining and geotechnical industries to avoid similar recurrences elsewhere. This is an extended abstract only. CITATION:Robotham, M, 2018. Bingham Canyon Mine – from adversity to excellence, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 3–4 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By J Carswell, K McTyer

The Pajingo gold operation in Queensland is approximately 50 kilometres south of Charters Towers and 134km south-west of Townsville. The resource was discovered in 1983 and first open pit gold production began in 1986. The mine traditionally employed a bottom-up sequence – a combination of modified and traditional Avoca methods with run-of-mine waste backfill. This practice caused many high-grade crown pillars to be left in place, yet accessible. In recent years, these crown pillars have been extracted by injection grouting of rockfill. This process facilitated blind up-hole open stoping. To date, thirteen separate injection campaigns have been completed, of which ten were deemed successful. In general, the two key technical difficulties in this mining technique are: maintaining a consistent high-quality ground consolidation of the rock fill material; and controlling the drill and blast practices during stoping. Here, effective drill-and-blast control was found to be essential to achieve the dual aims of 100% extraction, and maximum sill pillar stability to minimise dilution. During stoping, the technical performance of the consolidated rock-fill was recorded; both to verify the design, and to identify operational improvements. The results showed that Pajingo has realised both reduced production down-time through use of early strength gain grout, and more rapid and thorough grout consolidation through changes to the emplacement method. The optimisation of consolidated rock fill has led to several quantifiable benefits to the mine, including: profitable extraction of previously sterilised crown pillars resulting in both increased ore reserves and production profile; improvements to the stability of grouted stope crowns, thereby reducing safety and production related; risks associated with open up-hole stopes; reduction in cost and time constraints, with respect to the grouting of loose fill; and reduction in grout curing time – from 14 days to 8 days – thereby minimising production down-time. This paper is a case study of the evolution and optimisation of the up-hole open stoping mining method at Pajingo. The challenges and successes are discussed in terms of their key mining outcomes. CITATION:McTyer, K and Carswell, J, 2018. Evolution of rock fill consolidation at Pajingo Gold Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 66–77 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By C Zhang, I Canbulat, G Fan, D Zhang, C Wang

A clear understanding of the intensity of coal and rock burst is the basis for future research on burst mechanism and control. There has been a wide variety in the description of coal and rock burst damage at different countries using multi-methods, which makes the common understanding even more challenging. Therefore, this paper presents a broad review on the quantifications of intensity of coal and rock burst and seismic risk around the world, considering critical factors including seismic energy, magnitude, peak particle velocity and ejection velocity. It is found that the seismic energy of coal and rock burst can widely range from 0.002 MJ to 60000 MJ, with equivalent Richter magnitude from -1 to 4. The daily seismic energies can be used for seismic risk potential assessment, with energy levels from 0.1 KJ to 10 MJ, which is much lower than the burst sources. The magnitude of the seismic events can be also estimated based on the weight of damaged coal mass and human senses of vibration and sound. For the seismic intensity represented by peak particle velocity (ppv), it keeps constant within fault radius and attenuates with a speed of 1/r4 and 1/r in near and far field respectively, thus it is possible for a small seismic event to induce considerable ppv causing severe damage if the epicentral distance is small enough. There has not been a strong correlation between the ejection velocity and ppv, as seismic energy is only one of the energy sources that contribute to the kinetic energy of burst damage. CITATION:Wang, C, Zhang, C, Canbulat, I, Zhang, D and Fan, G, 2018. Intensity quantification of coal and rock burst risk – a review, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 223–233 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By H Masoumi, I Canbulat, Y Zhao, J Oh, H Lin

Borehole breakout is a drilling induced phenomenon caused by overstress of rock around the borehole. Its depth usually aligns with the minimum horizontal principal stress direction. For this reason, it has been used to determine stress orientations and a series of researchers also argued its dimensions can be indicative of stress magnitudes. If the stress dependencies of breakout geometries are well understood, it is possible to estimate stress magnitudes based on these data. This paper investigates the influences of critical parameters on breakout dimensions, including absolute stress magnitudes, stress ratios and borehole diameter. Several experiments have been conducted on cubic (120 x 120 x 120 mm3) sandstone samples with pre-drilled holes (22 mm and 30 mm) under true tri-axial loading conditions using UNSW self-designed equipment. Experimental results confirm the increasing maximum horizontal principal stress magnitudes result in larger angular span and longer breakout depth at constant minimum horizontal and vertical principal stresses. There is also a considerable discrepancy observed between experimental results and the analytical model. Findings of this study imply a potential on the estimation of stress magnitudes using borehole breakout. CITATION:Lin, H, Oh, J, Canbulat, I, Masoumi, H and Zhao, Y, 2018. Experimental investigation on borehole beakout and its implication on stress magnitudes, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 266–273 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By R Ulusay

Rock mechanics involves characterizing the mechanical properties and behaviour of rock material and the natural discontinuities of the rock mass, while rock engineering is concerned with specific engineering circumstances, for example, how much load will the rock support and whether reinforcement is necessary. Rock engineering models developed depend considerably on the input data such as boundary conditions, the properties of rock material and rock mass. Correct evaluation of these properties frequently requires laboratory and in-situ tests, supplemented with a high degree of experience and judgment. Accordingly, since 1974, the ISRM Commission on Testing Methods has spent considerable effort in developing a succession of the ISRM Suggested Methods (SMs) for different aspects of rock mechanics and rock engineering with the contribution of a number of working groups and cooperation of some other ISRM Commissions. This paper emphasizes the need and importance of standardization of rock testing methods within the context of the ISRM SMs, gives a guideline for developing ISRM SMs and finally discusses on some implementation and contractual issues associated with rock testing and experienced in practice, and briefly introduces main future trends in rock characterization, testing and monitoring. This is an extended abstract only. CITATION:Ulusay, R, 2018. Standardisation on rock characterisation, testing and monitoring with emphasis on ISRM suggested methods, practical issues and difficulties, and future trends, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 17–18 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By CIM Mineral Resource, Mineral Reserve Committee

The CIM Mineral Exploration Best Practice Guidelines (the Exploration Guidelines) have been prepared to assist professional geoscientists and engineers to conduct consistently high-quality work in order to maintain public confidence. The Exploration Guidelines are meant to assist professional geoscientists and exploration practitioners in planning, supervising, and executing exploration programs. In Canada, there are generally two types of public resource reporting: “Disclosure”, as defined by NI 43-101, is the reporting of technical information to the public and market participants for securities legislation purposes where a Qualified Person (QP) must be involved, and reporting of exploration information for governmental agencies to support obligations under laws including the Mining Acts of each of the Provinces and Territories. The Exploration Guidelines are also relevant where the results will not be publicly reported but are intended for internal company use. While this document is intended as guidance for work conducted or supervised by geoscientists in Canada, many of the practices described herein can be adapted to mineral exploration activities in other countries. The Exploration Guidelines are not intended to inhibit original thinking, or to prevent the application of new approaches that may develop into fundamental components of successful mineral exploration programs. Rather than provide prescriptive solutions to specific issues, they include general guidelines for current professional practice and to demonstrate and defend the merits of new methods. These guidelines do not preclude individuals and companies from developing more detailed guidelines specific to their own requirements. The initial version of the Exploration Guidelines was prepared by the Canadian Institute of Mining and Metallurgy and Petroleum (CIM) Exploration Best Practices Committee and adopted by CIM Council on August 20, 2000. On January 9, 2018, CIM Council formed a new committee, the Mineral Resources and Reserves Committee (CIM MRMR Committee) with a mandate to, among other things, update the Exploration Best Practice Guidelines. The mandate for the committee was accepted by CIM Council on March 2, 2018. The new document was adopted by the CIM Council on November 23, 2018.

Nov 23, 2018

By Felipe Poffo, Flávio Messas

Due to the high level of competition in tooling sector, a necessity to increase the level of processes and assets management has initiated. Based on the World Class Manufacturing methodology, applied mainly in serial production industries, we have challenged ourselves to adapt the main concepts and implement them in a tooling company. After one work year, we could notice 29% productivity improvement in the bottleneck process, 25% cost reduction in outsourcing, standardization of the processes, 8% reduction in direct labor. Consequently, it was possible to implement a financial reserve and a long term planning cash flow.

Nov 22, 2018

By Giuseppe Pintaude, Carlos Mauricio Lepienski

The evaluation of the tribological behavior of thermochemically treated surfaces, such as carburising and nitriding, is of uppermost importance for the productive chain of tools, molds and matrices. However, the use of tribological tests for these surfaces should be well selected to avoid erroneous evaluations, in particular considering the effect of the substrate at different levels. In this context, the linear scratch test may be well suited to distinguish the roles of the surface and the substrate. For that purpose, this paper presents a review on the use of this type of test for tribological evaluation in terms of the performance of thermochemically treated surfaces. The approach used is multiscale, considering what types of results are obtained from each load range used and the applications for each one of them.

Nov 22, 2018

By Hirohide Kamada, Gustavo Scarpim

The increase in industrial demand is responsible for a consequent evolution in the process of injection of aluminum under pressure (Die Casting) to achieve requirements such as; greater geometric complexity of injected parts, larger dimensions, hard-filled cavities, thin walls, and more refined mechanical and aesthetic requirements. Thus, the industries have searched for sensible increases in pressure and injection speed, always combining the best resistance and performance of the wells submitted to the new process conditions. The need for more aggressive applications for the cavities means that there is a constant evolution of the entire production chain in the manufacture of molds, passing through several processes, among them; machining, designs with complex engineering solutions, refining in the process of heat treatments and surface treatments. Allied to these needs, high performance steels manufactured by differentiated processes with high fracture resistance, hot strength and wear must be selected. This work aims to present the main factors considered in the development of high performance molds, the engineering of materials involved, technological trends and technical engineering solutions for the different variables of the die casting process.

Nov 22, 2018

By Paulo de Tarso Rossi Haddad, Eric Valmir Spósito, Cristiane Sales Gonçalves

The heat treatment is a process that acts as a key factor in the tool life of tools made with hot work tool steels. Due to their applications, the main desirable metallurgical properties of this material class are toughness and hot resistance, without which the tools may suffer premature failure, and may lead to increases in the cost of producing articles made using such tools [1, 2]. Therefore, special attention must be given to the heat treatments practiced in these steels, whose operations involve quenching and tempering. The present work carried out the effects of the austenitizing and tempering temperatures on the microstructural condition, hardness and impact properties of TENAX300IM®, modified AISI H11 with lower silicon content. Hardness was measured by the Rockwell method, C scale; the toughness was evaluated by the Charpy-V impact test; and the microstructure for each condition was evaluated by optic microscopy. It was shown that higher austenitization temperatures resulted in increased grain size and hardness; higher tempering temperatures resulted in reduction of hardness, and secondary hardening peaks were observed for some austenitization conditions. The impact resistance showed an inverse behavior to that of the hardness, remaining initially constant, up to ~ 550 ° C of tempering temperature, and then increasing with the tempering temperature. The microstructures presented great dissimilarity, mainly due to the dissolution of carbon and alloying elements in the matrix.

Nov 22, 2018

By Carlos Renato Inchoste Meure, José Ernesto Boff

Nowadays, many companies have the idea where to be occupied is to be productive, this work aims to show with practical tests that to get the best performance of the machine with tools of high performance and yield is the best option for a company to become productive and economic at the same time . The company targeted for this work began its activities in the Metallurgical branch more than 75 years, Metisa Metalúrgica Timboense serves the national and international market with several product lines. Due to its large backlog of overdue hours, a job was started in the tooling sector to make the process faster and more economical. In this context, this work has as general objective the restructuring of the critical processes of the tooling sector, aiming at a better functioning of the organization and greater satisfaction of its direct clients. In addition, this work has specific objectives, such as (1) application of high performance tools, (2) analysis and improvement of existing processes, development and application of new processes, (3) (High Speed Machining) (4) production monitoring and technical support for maintenance of new processes. Thus, after the implementation of the process improvements, it was possible to obtain a reduction of 81% in the final cost and 80.5% in the process time. In addition, with some of the new processes deployed, there was a reduction in the use of personal resources and better management of machine hour load and a significant gain in the sector response time.

Nov 22, 2018

By P Nichols, C te Kloot, A Harrison

Ernest Henry mine (EHM) is a sub-level caving operation located in north-west Queensland, Australia. Located below a previously mined open pit, the underground operation ramped up production to 6.8Mt/a in 2017. The EHM ore body dips at 45 degrees to the South and therefore requires each level to “step out” from the level above as seen in Figure 1. Within this step out zone it is important to both maximise recovery and allow for efficient operation of the underground workings production to bring the level up to full production as quickly as possible. Throughout the step out design process, a combination of further defining the ore boundary, using lessons learnt from production performance on upper levels and the introduction of design improvements, has reduced the production ramp-up time, decreased costs and increased recovery for a single level at EHM. CITATION: Nichols, P, te Kloot, C and Harrison, A, 2018. Case study – Ernest Henry Mine: designing step out zones in an inclined sub-level cave, in Proceedings Complex Orebodies Conference 2018, pp 53–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By E Holloway

The optimisation of an open pit mine can be broadly split into two stages, the first being the ultimate pit optimisation (and subsequent stage designs), and the second being schedule optimisation. Macroeconomic uncertainty clearly impacts on both however interrelationships do also exist. Generally, the opportunity exists for the ultimate pit to be revised during each planning cycle, however when this reprieve is removed the uncertainty for the underlying business increases. As one example, the introduction of an in-pit waste dump can be seen to significantly limit the option to revise the ultimate pit. When in this situation there are two potential risks that present: (i) the long-term price used for the ultimate pit selection is optimistic, and too large of a pit is selected resulting in waste being mined which uncovers material not of a significant value to deliver a profit; (ii) the long-term price used for the ultimate pit selection is pessimistic, too small of an ultimate pit is selected, and ore of realisable economic value left behind. Both of these outcomes are risks and as such can be assessed and quantified. CITATION: Holloway, E, 2018. Incorporating economic variability into a strategic planning framework, in Proceedings Complex Orebodies Conference 2018, pp 88–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By J Sykes, W Treasure, A Saleem, A Trench, S Ulrich, R S. Davies

Below-ground technical complexity remains a traditional source of project challenge. Above-ground challenges then augment this complexity, including in the domain of commodity marketing. All challenges must be solved to produce quality, saleable, ex-mine product. The situation is further complicated in that technical complexities are not independent of each other, so complexity is best regarded as a system rather than a series of isolated factors. Additional above-ground challenges to mining projects are also increasingly sourced from societal and environmental factors, locally and globally. These challenges not only confer project complexity, but have their source in larger, global wicked problems. Finally, financing and resourcing of projects represents an ever-present challenge for all but the highest-quality mineral deposits. CITATION: Trench, A, Davies, R S, Saleem, A, Sykes, J, Treasure, W and Ulrich, S, 2018. On the sources of complexity in contemporary and future mining projects, in Proceedings Complex Orebodies Conference 2018, pp 65–66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By K Biegaj, S C. Dominy

A high-nugget effect and presence of coarse gold characterises many styles of gold mineralisation. The effective sampling of these deposits is often difficult because of the relatively low concentrations involved and erratic nature of the gold or other minerals. Geometric and/or metallurgical complexities often compound this effect. Underground development, in-fill drilling and bulk sampling/trial mining are generally required to delineate Ore Reserves. Similarly expensive definition strategies often apply to surface mining in complex orebodies of gold and other minerals, including precious stones. Development, particularly winzing is a historical technique that was used to gather geological, grade and metallurgical data during underground and near-surface exploration. It permits access to the mineralised structure below the surface datum to determine viability. Winzing has always been considered an arduous and dangerous task. Modern winzing technology has led to the development of the Mobile Supersucker – essentially a giant vacuum cleaner with underground and surface capabilities. By the elimination of shovel-loaded blasted winze material into a kibble and hoisting, this system permits safe and highly efficient winzing activities, and allows the collection of bulk samples for grade and metallurgical evaluation, as well as access to the mineralisation for geological and geotechnical mapping. Bulk samples from horizontal development have long been collected to help define mineable grade via pilot processing. However, when defining blocks below current development, there has been over-reliance on ineffective ‘small sample’ drill data. The Mobile Supersucker permits the development of winzes and off-winze sub-levels. These provide critical information to a mine technical team when trying to justify capital to go deeper or commence or deepen an existing open pit. CITATION: Biegaj, K and Dominy, S C, 2018. Lowering risk in complex mineralisation: application of mobile supersucker development, in Proceedings Complex Orebodies Conference 2018, pp 113–115 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By M Tayebi-Khorami

There is an increasing trend in the extraction and development of copper resources from complex deposits. The complex deposits pose mineral processing challenges, as they often contain low grade copper ore, relatively large quantity of clay minerals, complex texture, very fine disseminated ore, high amount of pyrite, and high level of impurity elements such as arsenic. With the amount of arsenic in concentrates increasing and with environment, occupational health and safety regulations becoming more restrict, there is a need for a processing method that results in no arsenic emissions and captures all arsenic while immobilizing it in a compound that is stable under a wide range of conditions, so it is suitable for long-term disposal. Some development work has been undertaken to examine the most effective arsenic treatment option for complex orebodies that contain arsenic, but a technically robust and economically viable option has not yet been developed. Previous research has demonstrated the possibility of separating arsenic-copper sulphides from other copper minerals by controlling the potential of the flotation pulp in the single mineral systems. The selective flotation of enargite from copper sulphides in a real complex ore system was studied by Tayebi-Khorami (2016), which is summarised in this paper. CITATION: Tayebi-Khorami, M, 2018. Arsenic in complex orebodies, in Proceedings Complex Orebodies Conference 2018, pp 132–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018