Search Documents

By Y. H. Tang, H. Y. Zhang

"Tailings from lead-zinc mine contain plenty of dolomite and low-grade fine-grained barite, which is difficult to enrich by mineral processing. Since the density of barite and dolomite has some differences due to the fine dissemination size in a complex sedimentary, the gravity separation tests were conducted with no results obtained. The magnetic separation was conducted to remove the magnetic gangues, and the results were not satisfactory because of the gangue minerals such as limonite and others were low in content. The results of floatation tests showed that the mineral separation of barite and dolomite is quite difficult because that they have similar mineral floatability. Experimental research shows that the good results can be obtained by “desulfurizationbarite floatation” processing with the new depressant TS. The barite concentrate containing BaSO4 91.27%, BaSO4recovery is 70.25% when sodium dodecyl sulfonate serves as a collector and TS as the depressant.INTRODUCTIONBarite is an important mineral material. Often associated with other minerals, it usually needs to be separated by mineral processing in order to meet the application requirements. The main barite beneficiation methods include hand sorting, gravity separation, floatation, magnetic separation, acid leaching, etc. Usually barite associated with oxide ore such as fluorite dolomite, quartz ore etc. are also associated with sulfide ore such as pyrite, sphalerite and galena. The separation between barite and sulfide ore (such as pyrite) is easy. On the other hand, the separation between barite and oxide ore (such as dolomite and fluorite) is very difficult. There are quite a lot of reports on the separation between barite with fluorite dolomite however the separation between barite and dolomite is seldom discussed.The ore properties are quite complex attributable to mineral assemblage containing a large amounts of dolomite. As the density of barite and dolomite has some differences, gravity separation between them is usually easy. The gravity separation tests were conducted with no results obtained due to the fine dissemination size in a complex sedimentary. The magnetic separation was conducted to remove the magnetic gangues, and the results are not satisfactory as the gangue minerals such as limonite and others were low in content. Due to the fine dissemination and intimate association of minerals, and barite and dolomite contain the same group ions of Ba2+, Ca2+ and Mg2+, the results of flotation tests showed that the mineral separation between barite and dolomite by flotation means problematic. Previous studies have been conducted by several institutions but none to date has come up with a satisfactory process in dealing with the deposit. This may be attributable to: high cost of reagents; unsatisfactory performance. Therefore, the key to the flotation separation of barite and dolomite is the application of selective inhibitors. Based on previous test observations and years of extensive research experience in barite processing technology, with the new depressant TS has selectivity inhibition on dolomite developed and used, good results can be obtained by “desulfurization-barite flotation”, which allows barite in the lead-zinc tailings to a comprehensive recovery."

Jan 1, 2018

By I. Nishkov, I. Grigorova, M. Ranchev, S. Dzhamyarov

"Chelopech concentrator (part of Dundee Precious Metals) is located in central-western Bulgaria. The current process plant utilizes conventional primary crushing and SAG mill grinding, copper and pyrite rougher and cleaner flotation stages to produce a marketable gold-rich copper and pyrite concentrates. As in the most processing plants, the pyrite depression is carried out alkaline media using lime. The subsequent activation of pyrite mineral is achieved by adding sulfuric acid, which has an adverse effect on the flotation equipment. Therefore, a series of laboratory flotation experiment for activation of lime depressed pyrite by ammonium salts, such as ammonium chloride (NH4Cl), ammonium sulfate (NH4)2SO4 and ammonium bicarbonate (NH4HCO3), have been conducted. The obtained results showed that ammonium bicarbonate proved to be the most appropriate reagent choice for pyrite mineral activation. These results are confirmed by X-ray photoelectron spectroscopy (XPS), performed to determine the surface chemistry of pyrite in its natural state, after lime treatment and subsequent treatment by NH4HCO3. The registered XPS spectra indicate that the hydrophilic phases on the pyrite surface could be efficiently removed by using the ammonium salt NH4HCO3. The industrial use of NH4HCO3 as an activator of lime-depressed pyrite is a possible alternative for sulfuric acid replacement as a most widely used pyrite activator. Flotation experiments with addition of 200, 400, 600 and 800 g/t from each of the studied ammonium salts have been conducted. Furthermore, the impact of the flotation pulp pH within the scope of 9.00 – 10.50 was also investigated. The obtained results from the laboratory flotation experiments, showed that the pyrite activation with ammonium bicarbonate is an excellent possibility for replacing the sulfuric acid as main pyrite activator reagent, in order to eliminate the gypsum accumulation during the flotation of pyrite in Chelopech concentrator.INTRODUCTION The Chelopech deposit, located about 60 km east of Sofia is one of the largest Cu-Au deposits in Europe. The ore have complicated mineralogical and chemical composition. The main ore minerals are represented by pyrite, enargite (luzonite), tennantite, chalcopyrite and bornite. The average copper content of the mined ore is about 1.1 % and the gold content is about 4.0 g/t."

Jan 1, 2018

"Mining used to be a business primarily focused on the technical aspects of getting valuable ore out of the ground and extracting the minerals efficiently. Without denying the importance of these skills, a narrow focus on technical issues is no longer enough to guarantee success when it comes to exploiting rare earth element (REE) deposits. Molycorp failed to enter the global REE market in a successful manner, while none of the many REE exploration projects has turned into an active mine so far and none is expected to commence operations in the near future. Accordingly, the world of REE is far more complex compared to other commodities. This paper looks into the REE industry to identify the factors that can connect potential U.S. REE mines to the market. The ability to break free from past thinking and become future-focused is a key driver. Mining of REE is pointless without a corresponding value-adding chain, while developing a value chain without first establishing an uninterruptible source of REE is also senseless. The mining sector must be based on the REE value chain and vice versa, along with the establishment of a market channel for the REE products that come out of the mine. INTRODUCTION It has been seven years since rare earth elements became the subjects of front-page headlines. It was when the controversial Chinese export policy for these critical commodities was epitomised in a maritime border dispute with Japan in September 2010 that resulted in the big REE crisis and price spike of 2011 (Barakos et al, 2016c; Mancheri, 2015). The world was dismayed, especially in REE-importing countries, such as the United States that was and is still totally dependent on Chinese production and exports (Barakos et al, 2016c; Kennedy, 2015). The short-lived alarm initiated a treasure hunt by way of exploration for REE deposits all over the world. The continuously growing demand on the one hand and the Chinese sovereignty of the REE-market on the other, led the rest of the world to explore their own REE resources. In just a few years, more than 400 projects were initiated to explore REE deposits outside of China (ERECON, 2015; Goodenough, 2016). The prices of REE, however, dropped rapidly and at the moment of writing this paper are in 6-year lows, at the level of the price average before the 2011 crisis (Barakos, 2017). The viability of even major established producers is being challenged, not to mention the development prospects of potential REE-market entrants (Barakos et al, 2016b; Rollat et al, 2016). Production cutbacks and industry consolidation in China impel REE market experts to forecast that prices have already reached their lowest point and have nowhere to go but up (Adamas, 2015; Roskill 2015). Yet, expectations for increased REE prices are limited and drastic changes are unlikely to happen in the near future, as there is still excess supply in the overall REE market (Barakos, 2017). Nevertheless, the low prices of rare earths are not the only reason that potential producers are struggling to enter the global REE market. Among other parameters, the separation of the individual elements seems to be the most important factor, as it is technically challenging and expensive to build and to operate."

Jan 1, 2018

By T. Fraszczak, U. A. Peuker, T. Mütze, T. Leißner, A. Wikedzi

The present paper highlights on the comminution and liberation properties of two greisen-type lithium bearing-mica ore blends (L1, L2) subjected to different breakage devices; cone crusher (CC), roller crusher (RC), rotor beater mill (RBM) and a screen mill (SM). The particle size distribution (PSD) of the products from each device were evaluated to search for an appropriate PSD model using Gates-Gaudin-Schuhmann (GGS) and Rosin-Rammler (RR) functions. In order to determine an appropriate function that could better describe the PSDs from the devices used, the coefficient of determination (R2) was used as a criterion. In terms of mineral liberation studies, due to costs, only products from rotor beater mill (RBM) were examined through an automated scanning electron microscope (SEM) technique. It was found that RBM, RC and SM products were better described by the RR model than the GGS model with higher R2 values (0.97-1.0). However, cone crusher products for L1 were better described by GSS model, while that for L2 were better described by RR model. In terms of the spread of size distribution as indicated by RR model parameters, RC products were more uniformly distributed compared to products from other devices, for both ore blends. Also the RBM products were more scattered than products from other devices. The results indicate that the composition of individual ore blends affected the comminution products PSDs since different PSD model parameters were obtained for samples comminuted by same devices. The modal mineralogy of the two ore blends indicate both to be rich in quartz, topaz, zinnwaldite and muscovite. Further, the result indicate that, for both ore blends, zinnwaldite phase is more enriched in the fraction < 250 µm. Moreover, better liberation of zinnwaldite is observed for L1 compared to L2. This could be explained by differences of the two ore blends in three aspects; the nature of mineral association, reduction ratio of the fractions analysed and the nature of spread of the size distribution.

Jan 1, 2018

By D. Saramak

"High-pressure grinding technology is considered as one of the most efficient techniques of ore comminution, especially in terms of energy consumption. HPGR devices has been utilized in many mining-related industrial sectors, including iron and non-ferrous metal ores processing (copper, platinum, gold), as well as cement and limestone flour production. Even though the technology well known (introduced into mineral processing circuits in 80’s), there are still examples of ineffective operation of HPGR devices. This is a result of improper application of HPGR into individual crushing circuit. The purpose of the paper was to analyze selected effects achieved in HPGR on the course and effectiveness of beneficiation operations. Investigations were carried out for copper ore, and investigative programme was run for different values of HPGR pressing force, as well as changeable ore characteristics (content of fine size fractions, material moisture). All crushing products were then treated in flotation process, in order to determine useful mineral recovery. Results of investigations show that HPGR operating pressure influences the metal recovery in proportional way, however too extensive pressure values have relatively lower impact on increasing of the metal recovery. Particle size distribution of HPGR feed and its moisture have lower influence on recovery level than HPGR pressure, but too extensive moisture content influences the higher energy consumption of the roller press, together with less effective comminution. The second aspect raised in the paper was a possibility to control and optimize the HPGR-based circuit. There were presented the proposed approach to adjustment of HPGR operating parameters that enables the higher metal recovery.INTRODUCTION The high-pressure grinding technology, invented and developed by Professor Schoenert in 70’s (Schoenert, 1979), is currently regarded as one of the most efficient methods of hard ore comminution. Since then the technology was introduced into raw materials treatment circuits in many mining and mining-related industrial sectors, including iron and non-ferrous metal ores processing (copper, platinum, gold), as well as cement and limestone flour production. Considerable number of works concerning modeling and optimization of HPGR operation were also presented (Daniel & Morell, 2004, Tavares, 2005, Saramak, 2012, Saramak & Kleiv, 2013). Nowadays high-pressure grinding rolls devices are considered as well know technology with over 500 sold machines, according to various sources."

Jan 1, 2018

By Y. S. Sun, P. Gao

"In this investigation, a pilot-scale suspension magnetization roasting reactor was introduced and used to enhance magnetic properties of an iron ore. Consequently, the effects of roasting temperature, reducing gas CO flow rate and fluidizing gas N2 flow rate on the magnetization roasting performance were investigated. The results indicate that the hematite and siderite are almost completely converted into magnetite by a gas mixture of 3.5 Nm3/h CO and 2 Nm3/h N2 at roasting temperature of 520 °C. Under the optimized conditions, the magnetic iron concentrate with an iron grade of 60.18% and iron recovery of 90.17% was achieved. The XRD and Fe mineral phase analyses revealed that most of the hematite and siderite were converted to magnetite, and the magnetic properties were greatly enhanced. INTRODUCTION The steel and iron industry in China has rapidly developed in recent years requiring a large quantity of iron ores. Low-grade and complex iron ores are currently the overwhelmingly dominant mineral resource for iron in China. Therefore, China depends on imported iron ore resources heavily, resulting in an increase in the production costs of iron-making and steel-making[1-3]. Using domestic resources to produce a steady supply of high-quality iron ores is an important step toward the sustainable development of the steel and iron industry[4-5]. The iron ore from Jiuquan iron and steel company is abundant and recognized as typically complex iron ore resources in China. Magnetization roasting followed by low-intensity magnetic separation has been proven as the most feasible methods to upgrade refractory iron ore[6-10]. In present research, an innovative roasting technology, namely suspension magnetization roasting, was developed and applied to recover iron from a typical refractory iron ore. Suspension magnetization roasting technique and equipment developed by Prof. Yuexin Han’s Group at Northeastern University (NEU) is an effective way for the utilization of refractory iron ore. The advent of suspension magnetization roasting will, in China and even globally, produce a significant technological revolution in the field of iron ore beneficiation. Based on the previous works, this paper mainly described experiments on the separation and recovery of iron from a complex refractory iron ore by means of suspension magnetizing roasting and low-intensity magnetic separation processes. The purpose of the research is providing a new technology for effective utilization of refractory iron ore. Process parameters that affected the separation and recovery rate of iron were conducted and optimized, and the reaction process was analyzed by XRD and Fe mineral phase analysis."

Jan 1, 2018

By J. Starkey

A comminution circuit in recent history, is one of the most difficult parts of a mineral processing plant to design with confidence. It is usually the most costly part of a plant to build, and it can consume up to half or more of the energy used on a mine site. To suggest that comminution energy usage is sustainable in the long term is not possible at this time. What we have to choose from today, based on more than 50 years of experience, does include the best available technology, and the best way to design it. There is controversy in the industry as to how to properly approach the subject of comminution design, with many of the optional solutions requiring a level of training and expertise beyond the ability of a non-specialist engineer. Semi-autogenous grinding technology in particular, has not been properly appreciated because of many recent mistakes in its application and design, which have blurred the positive perception about what SAG technology is, how it can be used, and how it needs to be designed and built. In order to change this, mine owners and senior managers need to take responsibility for, and learn to understand the fundamental challenges that a comminution circuit poses to the project, to the design process, to the operators who use the equipment, and to the resulting metallurgy. This address is intended to summarize these challenges and offer fundamental engineering solutions, which are clear, specific and in a format which is directly applicable to the mining and mineral engineering community.

Jan 1, 2018

By Edgar Schach, Tom Leistner, Markus Buchmann, Urs A. Peuker, Martin Rudolph, Marius Kern

"In this study, the flotation characteristics of a cassiterite-bearing fine-grained and complex skarn ore from a deposit in the Ore Mountains is investigated. The tests are performed using an oil-assisted column flotation approach to process very fine ore fractions and avoid losses of cassiterite into the tailings. First, process parameters are obtained for a finely ground artificial mixture of quartz, magnetite and cassiterite, simulating the real ore. Thereby, magnetite is used, as iron oxides can have a detrimental effect on the flotation due to a similar flotation behavior. In addition, they can act as a source of multivalent ions, which are known to reduce the concentration of collector molecules, active for flotation. Based on the results, selected parameters are further tested for cassiterite skarn ore from the Hämmerlein deposit including a pre-conditioning and a water exchange step to remove ionic contaminants. The process response is analyzed in detail by XRF (X-ray fluorescence) and MLA (mineral liberation analysis) to get a better understanding of the behavior of the single ore components. Sulfosuccinamate type surfactant is utilized as the collector, emulsifier and to reduce the froth destabilization through nonpolar oil. Sodium hexafluorosilicate is added as the depressant.INTRODUCTION Complex skarn ore deposits containing considerable amounts of tin, indium and other metals are located in the Ore Mountains region (Germany). In this study, a skarn ore from the Hämmerlein deposit was investigated. Due to the finely disseminated nature of this ore, past beneficiation attempts failed, and the ore was considered economically unprocessable. However, increasing resource demands brings it back into focus (Schuppan and Hiller, 2012). Cassiterite is the main tin bearing mineral in this ore. Due to its high density (~7 g/cm³), the predominant beneficiation technique is gravity separation (Angadi et al., 2015). Tin ores from disseminated deposits have to be extensively comminuted to reach a sufficient degree of liberation of the cassiterite grains. As cassiterite has a brittle nature, it is preferable enriched in small size fractions, during comminution (Angadi et al., 2015). Gravity separation methods become more and more inefficient for particles smaller 40 µm (Falcon, 1982), causing tin losses of up to 30 to 40wt.-% (Angadi et al., 2015). Thus, froth flotation of cassiterite was first utilized in Altenberg in the Ore Mountains as an additional processing step to reduce the cassiterite losses into gravity separation tailings (Bulatovic, 2010; Gruner and Bilsing, 1992). Although the reported lower size limits for an effective cassiterite floatability are often smaller compared to other minerals, the flotation performance is in general decreasing for small particle sizes < 10 µm (Trahar and Warren, 1976). Therefore, different approaches have been already investigated for the flotation of such fine cassiterite fractions to overcome the limits in particle size. Bilgen et al. investigated the shear flocculation of cassiterite with a sulfosuccinamate collector (Bilgen et al., 1994). The agglomeration flotation of cassiterite has been tested by Schubert et al. (Schubert et al., 1966), in which the selective coagulation of fine hydrophobic particles and oil droplets leads to an increase of the effective particle size. Recently, Leistner at al. investigated an oil-assisted agglomeration flotation for ultra-fine cassiterite ore fractions (Leistner et al., 2016). However, a poor response due to an increased concentration of Fe and Ca ions, unselective oil/gangue coagulation and froth instability, that is caused by oil/frother interactions, has been observed."

Jan 1, 2018

By A. V. Bogdanovich, S. A. Urnysheva

"Gravity and X-ray luminescent separation methods are generally used in processing of diamond ores. X-ray luminescent separators are applied for separation of diamonds from feed ore size fractions from 100 to 10-15 mm size and for final treatment of gravity concentrates over 1 mm size. Gravity separation machines used for diamond ores separation are heavy medium cyclones and pneumatic jigs. One of the most important parameters, to a large extent affecting diamonds recovery from ore, as well as processing costs and specific energy costs, is size of dumped final tailings. That was exactly the purpose of the studies, the results of which are described in this paper. The studies performed on different ores showed that in order to achieve high recovery results, it is necessary to dump heavy medium separation tailings below 3 mm size. Separation of final tailings of -6+1 mm size by jigging is also possible. However, with a view to exclude extra diamond losses, it is necessary to maintain jigging concentrate yield approximately at 25% from starting feed, with its subsequent cleaning in heavy medium cyclones. In addition to that, it is necessary to separate 20-25% of middling with diamonds content at feed ore level and subject it to grinding. This will complicate flow sheet, but reduce load on heavy medium cyclones. In order to develop optimal flow sheet for gravity concentration of a specific diamond ore, large-scale investigations are required, including technical-and-economic assessment of separation alternatives. INTRODUCTION In processing of diamond ores, gravity and X-ray luminescent separation methods are generally used. It is common practice to apply X-ray luminescent separators for separation of diamonds from feed ore size fractions from 50 (100) to 20 (10) mm size and for final treatment of gravity concentrates over 1 mm size. With that, X-ray luminescent separation tailings larger than 3-6 mm size are reground and delivered to gravity concentration processing stage. Middling products circulation volumes are large, not infrequently necessitating decrease in concentrating plants capacity, especially with mining in deep workings of deposits, where ore strength is higher (Goryachev, 2010; Vaginov, 2000; William, 1988). Diamond ores preparation before processing is accomplished by means of roll-screw crushers and autogenous grinding mills, minimizing probability of free diamonds damage in liberation from barren rock. In re-crushing of size fractions that are “difficult” in autogenous grinding, high pressure grinding rollers are applied (Burchardt, 2014; Fedotov, 2011a, 2006b)."

Jan 1, 2018

By Francisco Sena Leite, Vinicius Miranda

Mine blasting is directly associated with ground vibration. If these affect critical structures (buildings pit walls, etc.) they must be mitigated to reduce the environment and social impacts. Vibration monitoring and control is one of the most important procedures in blasting because it will impact short and long term incidents associated with this blast effect. Technology moves ever forward, and today we have personal devices that are equipped with an array of sensors, for that reason the authors decided to investigate the possibility of using a personal device to do vibration control. This case study compares the same blast measured with a traditional seismograph and a smartphone. To validate this new methodology, attenuation laws were built with data from a traditional seismograph and a smartphone application. Predictions were also made prior to a set of blasts. Residual analysis was used for data validation from the two different sources. From the performed analysis, to prove the validity of this new methodology, the normality tests for statistics residues analysis proves that it is possible to infer that the model has a null residual mean and a small residual error. The achieved results show the accuracy of these devices, the authors pretend to show the potential of this equipment and open a completely new door for vibration analysis.

Jan 1, 2018

By Isobel Yeo, Florent Szitkar, Sven Petersen, Sebastian Graber, Meike Klischies

Technological advances and the shift towards green energies in the last decades have led to a substantial increase in the demand for metal resources. With rising political tension, and quasi-monopolistic production of some key metals, a secured supply chain cannot be guaranteed [1]. Therefore, the focus of the international research community and mining companies has expanded to the seafloor, looking for additional resources. The seafloor may have the potential to contribute significantly to a secure metal supply in the future. However, we have only investigated a fraction of our oceans in sufficient detail to assess the global resource potential. A detailed exploration of the vast seafloor is currently economically not feasible, due to its extremely time-consuming and costly nature. Seafloor massive sulfides generally form along the active plate boundaries and at active volcanoes in arc settings. However, the resources are not evenly distributed on the seafloor. Large deposits tend to be more common along slow-spreading and ultra-slow- spreading ridges that make up the majority of the global mid-ocean ridge system [2]. Therefore, it is important to establish geological models and exploration criteria in order to narrow down the permissive areas, which are likely to accommodate economically interesting deposits. Based on a detailed study of the TAG hydrothermal field in the central Atlantic Ocean, hosting a large active mound as well as several inactive mounds, we develop exploration methods and criteria to define areas of potential massive sulfide occurrences along slow-spreading sections.

Jan 1, 2018

By J. A. Dos Santos

"INTRODUCTION Dramatic reduction in energy use and environmental impact can be achieved with sandwich belt high angle conveyors that serve as the vital link in any IPCC (In-pit Crushing and Conveying) system. These high angle conveyors are not new at all, but have not found wide use in IPCC systems where they can realize the greatest advantage. Reduced energy consumption and environmental impact, with IPCC systems, was already realized in the 1970s. With the bulk material haulage limited to conventional open trough conveyors the most direct path out of the open pit was precluded, requiring low angle spiral ramps and/or deep slots and/or tunnels through the high wall of the open pit. These excavations, to accommodate the low angle limitations, represented undesirable impact on cost and on the environment. Against this backdrop, a major study in 1979 sought to develop high angle conveying systems that could continuously haul the mined bulk material directly out of the pit, along the high wall – the shortest distance between the two end points. Between 1979 and 1982, that study developed sandwich belt high angle conveying systems that utilized all conventional conveyor equipment including smooth surfaced rubber belts that could be continuously scraped clean. These systems had all of the positive features of conventional conveyors but overcame the angle limitation. By hugging the bulk material between two belts, the material’s internal friction could be developed to facilitate conveying at any high angle up to 90 degrees (vertical). After an intense testing period (about one year) on the first large scale prototype system, commercialization began in 1983 with the installation of a 60 degree incline system at a western United States coal mine, elevating 2000 t/h of coal to a train load out system. It did not take a long period of scrutiny and acceptance before this high angle conveyor found use in the most rugged requirements of an IPCC system. This was only the second commercial sale, and after more than 150 commercial installations, it remains arguably the most significant high angle conveying system. In 1984, a copper mine in Serbia, already using pit perimeter crushing and conveying, decided to move their primary crusher deep into the pit and to use a sandwich belt high angle conveying system to elevate the ore continuously, directly out of the pit, along the high wall to the pit perimeter where it then transferred to a conventional conveyor for the remaining haul to the plant. The system had significant features including 2000mm wide belts that elevated 250mm coarse ore, at 4000 t/h, over six 15-meter high benches for a total 90 meters of net lift. The system was able to reduce the truck haulage fleet by ten 200 ton trucks realizing great cost savings, zero emissions to the air and greatly reduced traffic congestion in the pit. The system operated successfully until 2002 when the mine shut down. Many successful sandwich belt high angle conveyors followed with the current count of commercial installations at more than 150. Despite the great success with this system, its use has not been repeated as part of an IPCC system."

Jan 1, 2018

By Elisabetta Tedeschi, Razieh Nejati Fard

Deep-sea mining is in the future perspective of mining industry and it is currently in the technological development phase. The focus of this study is on the electrical power system that provides sufficient energy for the mining equipment at the seafloor, excavating Seafloor Massive Sulfide (SMS) deposits. SMS deposits usually exist at water depths between 1500 m and 4000 m. Despite the similarities of SMS deposits excavation to the open-pit terrestrial mines, more energy is required to drill and crush the ores in the hyperbaric conditions [1], which can be done whether by static trench cutters [1] or by mobile mining crawlers [2]. In addition, the ores vertical transportation by subsea pumps requires several MW electrical power that can be supplied by all-electric subsea motors or hydraulically from water injection motors located on the surface. The power requirements can be fulfilled by an offshore or subsea power network. As the SMS mines are usually in remote locations, the straightforward solution will be an isolated offshore grid mounted on a vessel or platform similar to the most of offshore Oil & Gas projects. These power systems resemble the onshore microgrids for industrial purposes operating in island mode. However, in contrast with the onshore power networks, there are space and weight limitations in offshore infrastructures, which impose the design compactness to be a priority. In addition, having a very high reliability is necessary in the design approach of the offshore projects due to the extraordinary high expenses corresponding to repair and maintenance. The other design criterion is to improve the power system efficiency in order to reduce the size of the power equipment cooling apparatus, operational costs and CO2 emissions produced by diesel/LNG onboard generators. There are a few studies considering power system distribution for seafloor mining industry. Among them, [3] has investigated the AC and DC alternatives for SMS mining in 2400 m water depth by considering Solwara 1 project scenario introduced by Nautilus Minerals Inc. [2]. In this study, a power system design tool will be presented taking into account various water depth, power consumption levels, different distribution configurations (AC and DC) and the aforementioned design criteria.

Jan 1, 2018

By L. E. Veki, S. M. Luukkanen, J. P. Karvonen, J. O. Leppinen

Today there is a consensus that xanthate adsorption on sulfide minerals is primarily controlled by redox reactions occurring at specific potentials on these semi-conductive minerals. Consequently, it is possible to control xanthate adsorption by controlling electrochemical conditions in the system by using oxidizing and reducing agents. The scope of this study was to investigate the possibilities to increase the selectivity of Cu-Fe-Zn ore flotation by applying electrochemical control in the conditioning of the flotation feed. In this work, mild steel grinding in a nitrogen atmosphere was used as the basis to provide a negative starting potential and minimize the amount of oxidation products on sulfide mineral surfaces. To study how different potential levels affect flotation results, a controlled conditioning procedure was utilized maintaining potential at a desired level by titrating the pulp with air. Xanthate adsorption kinetics during conditioning was examined by taking pulp samples for spectrophotometric analysis and laboratory flotation tests were conducted for samples that underwent the controlled conditioning procedure in the potential range of -200mV to +200mV vs. SHE. A clear correlation was detected between chalcopyrite recovery and the potential during controlled conditioning indicating that there was a constant increase in chalcopyrite recovery when the potential was shifted to more anodic values. It is possible that utilizing potential control in the conditioning stage, a smelter grade copper concentrate can be achieved directly in rougher flotation without cleaning stages. Conditioning in favorable conditions had significant positive effects on flotation selectivity of chalcopyrite. The improvement in copper concentrate grade being predominantly caused by the depression of pyrite. By applying the controlled conditioning procedure pyrite recovery in rougher flotation was reduced even low as under 1%, while in the tests without controlled conditioning, pyrite recovery varied between 7.5 – 65.7%. The result of this work indicate that affecting collector adsorption by electrochemical control in the conditioning stage can provide significant improvement in sulfide mineral flotation and industrial applications could lead to decreased chemical consumption, reduced equipment and maintenance costs.

Jan 1, 2018

By C. A. C. Sequeira, G. N. Anastassakis

"The separation of fine or even smaller size mineral particles with conventional methods is inefficient due to the specific properties of fines (small mass, high specific surface area, and high surface energy per unit area). Hence, the production of high-grade concentrate with high recovery is very difficult to impossible and a significant share of mineral values is lost to the tailings. The aim of the current research is to investigate the possibility to efficiently separate value minerals from gangue of fine particle size. The objective of the current work is to develop separation schemes of fine mineral particles by combining an initial stage of particles agglomeration with the use of collectors (hydrophobic agglomeration) with a subsequent conventional separation method. In the current research, magnesite was used as mineral value to be separated: a) from quartz, and b) from mineral mixture (serpentine, ilmenite, and olivine). In each case, tests on single minerals and artificial mixtures were carried out. After hydrophobic agglomeration, the separation of magnesite from quartz was achieved by settling; in the second case (gangue: serpentine, ilmenite, and olivine), magnetic separation of the co-agglomerated gangue was applied. In both cases, the results of the preliminary tests on single minerals suggest that the separation of mineral value is feasible and efficient. These findings were also confirmed from the results of the tests on artificial mixtures of magnesite and gangue, either quartz only or mineral mixture. Both separation schemes provided with magnesite concentrates of commercial grade (95% magnesite) with high recovery. INTRODUCTION The generation of fine particles is inevitable in many operations of mineral commodities processing. Especially in the case of low-grade ores, the mineral value is finely disseminated in the ore, and considerable liberation occurs at a fine size range. Although there is not a uniform classification system with respect to mineral particles size, fines are usually characterized the particles with a size range of -100µm+20µm, very fines those of -20µm+5µm, ultra fines of -5µm+1µm, and colloids smaller than 1µm (Sivamohan, 1990)."

Jan 1, 2018

By Matt Slezak, Tristan Worsey, Nathan Rouse, Kyle Hall

As everyone knows, blasters are required to file blast reports of every blast for regulatory purposes. To this day, the authors see many handwritten blast reports. Handwritten blast reports are notorious for containing errors or omissions. This is not because the blaster intends to misreport information. It is because blasters have many tasks to complete in a day, are sometimes in a rush, and could accidentally miscalculate data, omit items, or record incorrect data. In most cases, blasters do not suffer consequences to these errors because blast reports are seldom reviewed in detail. In some cases, such as when a blasting operation undergoes some sort of litigation process, the reports are reviewed in detail and the blaster is ultimately held responsible. If the reports contain errors, the blaster can be fined, have his/her license revoked, or worse. Electronic blast reporting and centralized data management can help reduce or eliminate the potential for accidental blast reporting errors to occur. This paper presents many ways that electronic blast reporting can reduce or eliminate blast reporting errors, decrease time and extra costs spent reporting, and improve efficiencies in the field and the office.

Jan 1, 2018

By O. Jerez, A. Novoselov, L. Gutiérrez, J. Morales, U. Kelm

"In Chile, the evaluation to reprocess tailings for elements other than the traditional Cu, Mo, Au, and Ag, as well as projects to implement long-term monitoring of mining residue sites are key elements of the government’s roadmap laid out for the mining industry for the next two decades. Characterization routines for tailings and mining residues in general have to be adapted from traditional ore and gangue mineral and micro-chemical studies. This contribution summarizes key aspects for the regional mining industry for a basic characterization of tailings with emphasis on small- to medium-size operations with limited in-house facilities and funds to carry out extensive characterization programs. The oldest tailings in Chile were deposited almost a century ago; this fact gives importance to the recovery of past ore /gangue feed information, process circuits and changes (e.g. acid to alkaline flotation), process water provenance and recovery, meteorological registers, and routines of filling a tailings impoundment. Basic characterization should include X-ray fluorescence spectrometry combined with laser diffraction (LD) granulometry followed by X-ray diffraction (XRD), optical microscopy (OM) and automated mineral analysis (AMA) on a reduced set of samples identified by hierarchical cluster analysis. For this detailed stage, only coarse tailings are recommended for direct a study by microscopy and automated mineralogy (P80 >100 µm); for fine tailings (P80 ~30 µm) a combination of XRD and deposit type adapted sequential extraction are more informative options. In particular, for XRD of clay phases, losses of crystallinity may result in deviation of spectra from standard reference phases due to prolonged storage. To monitor surface alteration, scanning electron microscopy can be complemented by Raman spectroscopy to detect residual reagents on mineral surfaces. For reactivity modeling BET measurements are essential."

Jan 1, 2018

By L. A. Nemchinova, M. A. Arustamian

"For a long time tailings piles of mining and smelting complexes have met the eye being a prospecting feedstock source for many industries. Nowadays, 6.5 million tons of copper and cooper-zinc processing tailings are stockpiled in the Urals annually, as there is no technology of its processing to provide a full and complex metal extraction within mining and processing operations. In spite of large volumes of mining wastes, not more than 20% of annual overburden, approx. 10% of processing wastes, approx. 40% slags (1) are involved into processing.Based on today’s complex of economic, environmental and social challenges of ore processing, waste processing technology using existing capacities is a burning issue. Mining wastes characteristics (including fine dissemination, variability of physical and chemical properties of mineral surfaces under impact of oxidizing, leaching, etc.) predetermine challenges arising out of its involving into processing and justify high capital intensity of new construction or reconstruction projects followed by replacement of existing processing lines with new ones.In this paper, the authors propose flotation technology for mature tailings of copper, copper-zinc and polymetallic ore processing. The technology developed provides for upgrade of existing process flowsheet diagrams at minimum costs to produce additional saleable products including low-grade copper concentrate, saleable zinc concentrate and gold concentrate thus facilitates sustainable use of depleting minerals and operational efficiency due to cost-efficient processing of already mined materials, being in fact, final semi-products located near existing operations. This is particularly important for operations with standby capacities and not engaged workforce."

Jan 1, 2018

By A. P. Chaves, D. Jose Neto, M. G. Bergerman, E. S. Mano

"More complex ore comminution and concentration operations have found increasing application in the mining industry due to lower grades and higher complexity of the available ores. An alternative to coping with the higher capital and operating costs of ore processing plants is the use of pre-concentration stages. They allow removing a significant mass of material with little or no content of the relevant mineral before the ore is fed into the processing plant, with the consequent reduction in the mass to be processed in downstream operations. Significant benefits arise out of the use of pre-concentration, such as higher contained metal output without the need to increase the grinding or flotation capacity, and longer mine life. The grade of marginal ores could be enhanced to a level that would make their exploration economically feasible, which would result in increasing exploitable reserves. Nevertheless, few studies to date have assessed the resulting impacts on ore grinding energy consumption and wear after the gangue is removed through pre-concentration operations. This study evaluated the energy consumption and wear of grinding circuits in Brazilian mining operations in which the feed has gone through a pre-concentration stage. Such assessment was based on different samples of sulfide and oxide ores. Laboratory tests were carried out to investigate the power consumption and wear of grinding circuits with and without a pre-concentration stage. Laboratory test results were used to simulate industrial grinding circuits based on both alternatives and illustrate the environmental and economic benefits of each one.INTRODUCTION Increasingly complex ore concentration operations in several stages have found broadening application in recent years in view of lower grades and higher complexity of the available ores. An alternative to coping with the higher capital and operating costs of ore processing plants is the use of pre-concentration stages. Different ore processing technologies can be used for that purpose, such as magnetic separation, density segregation, and separation methods based on high-tech sensors (ore sorting). Currently, the most common methods are gravimetric processes, in view of their low cost, particularly jigging and dense medium separation methods, such as the drum and cone separators manufactured by Western Machinery Company, Teska, Drewboy, Norwalt, Dynawhirlpool and Tri-flo, and dense medium cyclones (CAMPOS; LUZ; BRAGA, 2010). The use of dry ore sorters has also grown significantly in recent years (Jose Neto et al. 2017). The selection of the separator type depends essentially on the ore particle size, required flows, and operating density ranges. All these methods may even be used after preferential blasting in mining (Grigg & Delemontex, 2015)."

Jan 1, 2018

By S. A. Kubyshkin, A. A. Agafonov, A. L. Shakhnin, S. M. Sukharzhevsky, A. A. Komlev, N. V. Vorob’ev-Desyatovskii, A. Pichugina

Cyanidation of gold ore results in formation not only of Na[Au(CN)2], but also cyanometallate complexes of some transition metals. During subsequent gold extraction from such solutions and pulps, using activated carbons (??), a number of problems arise. An effective solution of the problem is not possible without detailed knowledge of the interaction mechanism of transition metals cyanide complexes with AC particles. The chemical properties of AC particles and graphene, saturated with [?u(CN)n](n-1)- (n=2, 3), were studied by XPS, ESR, SQUID, and DFT. The obtained results were compared with the data on AC adsorption of anionic form of Ag(I), Au(I), Cd(II), Hg(II), Cr(III), Fe(II), Fe(III), Co(III), Rh(III), Ni(II), Pd(II), Pt(II) and Pt(IV) cyanide complexes. The adsorption of [?u(CN)n](n-1)- (n=2, 3) on AC from aqueous solutions in air is accompanied with oxidation of ?u(I) atoms. Besides, Cu(II) and Cu(III) compounds were found on AC surface. Quantum-chemical calculations confirmed the possibility of formation of Cu(I) complex with carbene-like sites of AC. The reactions of [?u(CN)n](n-1)- (n=2, 3) complexes and aromatic carbenes and their cation-radical were theoretically studied at DFT PBE level to obtain the information on adsorption of cyanometallate complexes on AC. Carbenes with different fragments were regarded as a model of activated carbons, which have free edge sites with paired o and n electrons. It was shown that [Cu(CN)2]- bounds firmly with triplet carbene, if one Cu-CN bond breaks. The dissociation process occurs through a multi-step spin-crossing mechanism to reduce total spin multiplicity of the metal-carbene complex. The behavior of transition element complexes in contact with AC in aqueous solutions is determined by the following characteristics: geometrical structure of ionic complexes; nature of ligands bonded to the central atom; concentration of reactive oxygen species in solution and its pH; nature of binding sites of AC.

Jan 1, 2018