Search Documents

By Peng Cao, Jimin Su, Yang Li

"Abutment pressure distribution is different when a longwall panel is passing through the abandoned gateroads in a damaged coal seam. According to the geological conditon of panel E13103 in Cuijiazhai Coal Mine in China theoretical analysis and finite element numerical simulation were used to determine the front pressure distribution characteristics when the longwall face is 70 m, 50 m, 30 m, 20 m, 10 m, and 5 m from the abandoned gateroads. The research results show that the influence range of abutment pressure is 40 m to 45 m outby the face, and the peak value of front abutment pressure is related to the distance between the face and abandoned gateroads. When the distance between the longwall face and abandoned gateroads is reduced from 50 m to 10 m, the front abutment pressure peak value kept increasing.When the distance is 10 m, it has reached the maximum. The peak value is located in 5 to 6 m outby the faceline. When the distance between the longwall face and abandoned gateroads is reduced from10 m to 5 m, the front abutment pressure sharply decreases, the intact coal yields and is even in plastic state. The peak value transfers to the other side of the abandoned gateroads. The research results provide a theoretical basis for determining the advance support distance of two gateroads in the panel and the reinforcement for face stability when the longwall face is passing through the abandoned gateroads.INTRODUCTIONFront abutment pressure is the result of rearrangement of in situ rock stress caused by the mining (removal) of the coal seam. Research on the distribution character of face abutment pressure have significant importance in confirming the width of the coal pillar and the distance of advance support in roadways (Liu et al., 2011; Liu, Jiang, and Zhu, 2015). Currently, there is a lot of research on abutment pressure characteristics of traditional longwall coal faces, thick coal seam longwall faces, isolated faces, and extra wide face abutment pressure distribution (Xie et al., 2006). However, theoretical analysis and research on the distribution law of the fully mechanized coal face to abandoned gateroads are relatively less. Abandoned roadways are often from less mechanized or room and pillar mines. Due to the existence of these roadways pre-longwall mining, the in situ stress has already been redistributed around the roadway (Liu et al., 2007). Thus, when the longwall approaches and mines through the roadway, the abutment pressure distribution behaviour has different characteristics than those of traditional solid undisturbed coal. Especially when the face approaches the abandoned roadway, the understanding of face abutment pressure distribution has significant importance to the timing of support installation (Ren and Ning, 2014). This prevents the occurrence of a roof and rib failure ahead of and on the longwall and highly efficient advance of the longwall safely and productivity. This paper analyses the E13103 face of the Cuijiazhai Mine of Wenzhou Mining Co., Ltd of Kailuan Group, as the engineering case study, and uses FLAC3D numerical simulation software to conduct numerical simulated analysis on the abutment pressure distribution mechanism of longwall coal mining face."

Jan 1, 2018

By K. Price, G. Wang, L. R. Moore, Y. R. Xiong, J. Gu

"Sand is a naturally occurring granular material that is a result of the physical or chemical breakdown of rocks. Raw/natural sand contains various minerals, and it is this combination of minerals that brings the value to the construction aggregate industry. However, it is the quartz component of sand that is valued in its application as industrial silica in glass, high purity quartz, foundry sand, and oil and gas fracturing. Depending on the industry, the grade requirements can be the concentration of SiO2, particle size or shape, as well as contaminants such as the heavy refractory minerals, clays, fines, and alkali metals. With the ever declining mineral feed grade, processors continue to face challenges making the industry specific concentrate grade. As such, it becomes more important to tailor make the processing reagents to fit the mineral, processing conditions, and desired quality specification. This paper focuses on the application of novel collectors towards the beneficiation of sand for each of the major industrial silica applications. INTRODUCTIONQuartz is a mineral composed of a framework of silicon and oxygen atoms. It is the second most abundant mineral in the Earth’s continental crust. There are many species of quartz, which are defined by the particle size, shape, and color. Silica sand is one of those species, which is the byproduct of the physical or chemical breakdown of quartz containing rocks or crystals. Geologist define silica sand as a silica mineral with a particle size between 0.05 and 2 mm in diameter (Zdunczyk, 2001). Silica sand has significant value to society in recreation (beach sand and toy boxes), construction aggregate (concretes and asphalt), industry (iron & steel casting, fracturing proppants, and glass), as well as specialty products such as semiconductors or silicon wafers used in electronics.The aggregate business is the dominant consumer of silica sand products. Conversely, glass making, foundries (casting material), abrasives, and fracturing proppants are the dominant applications for industrial silica sand. Not much beneficiation is required for sand products going into the construction industry, other than sizing and scrubbing to remove clay. However, the industrial silica sand applications are dependent on particle size, shape, and degree of contaminants, which sets the market value (table 1). Therefore, as the more specialty products are produced, more sophisticated techniques and chemistry need to be applied to ensure the appropriate quality is met."

Jan 1, 2018

By Hong Zhong, Shuai Wang, Xin Ma

"In this paper, we report a simple and effective process for producing a surfactant mixture of O-isopropyl-N-ethyl thionocarbamate (IPETC) and 4-(tert-butyl)benzyl mercaptan (BBSH). The composite collector was synthesized via one-pot reaction of sodium isopropyl xanthate, 4-tert-butylbenzylchloride and ethylamine using tert-butyl alcohol as solvent. The whole process for the synthesis of composite collector involves neither foul smelling reagents or intermediates, nor any by-products requires special treatment for disposal, and thus can be scaled up to an industrial level. The flotation response of chalcopyrite and pyrite independently with IPETC and BBSH collectors and with their mixture (the mole ratio of IPETC and BBSH is 1:1) was assessed. The microflotation results showed that the collecting ability of BBSH was slightly stronger than that of IPETC and that IPETC was more selective collector than BBSH against pyrite, and that the composite collector displayed a stronger collecting ability toward chalcopyrite than IPETC, and superior selectivity for chalcopyrite against pyrite than BBSH. The batch flotation results showed that composite collector exhibited better performance than IPETC and BBSH. It was demonstrated that the mixing of IPETC and BBSH would give rise to a synergistic effect significantly enhancing overall flotation performance. In addition, the adsorption mechanism of BBSH on the surface of chalcopyrite was conducted by adsorption test and infrared spectrum measurement, and the results showed that the interaction of BBSH on the chalcopyrite surface was dominated by the chemical adsorption, and the formation of a strong S-M bond plays a key role in the adsorption of mercaptans on minerals surfaces. The developed flotation reagents with special preparation method is the author’s original design, patented (patent of the People’s Republic of China) and have no analogues in the world of mineral processing. (Application number 201810100107.1, ""Alkyl thioether alcohol compounds, methods for their preparation and applications thereof "", China).1. INTRODUCTION Froth flotation is an essential method widely used in the mineral processing industry to selectively separate valuable minerals from gangues[1]. Worldwide, more than 109 tons of materials are treated annually by this method with the majority being metal sulfides and oxides[2]. Nowadays, the judicious utilization of complex sulfides to meet the ever-growing demand of mineral resources gains more attention, due to the gradual depletion of deposits with high grade, making imperative the development of new high-efficiency collectors and mixtures of collectors to process complex minerals. In comparison to individual collectors, the use of mixtures has several notable benefits including lower dosage requirements, improved selectivity, rates and recovery and an increase in the recovery of coarse particles[3-9]. Moreover, in terms of cost and environmental issues, using collector mixtures can reduce the total amount of agents used, thus reducing the overall effect on the environment and economic costs without affecting the flotation performance. Therefore, the search for high-efficiency mixtures of collectors is still interesting and relevant."

Jan 1, 2018

By R. Fernando

"The National Institute for Occupational Safety and Health (NIOSH) National Personal Protective Technology Laboratory (NPPTL) is leading an effort to develop the next generation of self-escape breathing apparatus for egress from confined spaces in emergency scenarios. A backpack style closed-circuit mine escape respirator design was one configuration explored as part of the research imperative directed by the 2006 MINER Act. Stakeholder feedback from MSHA and at the NIOSH Breathing Air Supply Partnership Meeting indicated a smaller belt worn unit that does not sacrifice performance is desirable. This paper outlines some further technology advancements that may be investigated toward developing such a small-sized respirator. Technologies being considered are novel chemicals for improved carbon dioxide (CO2) absorption and oxygen (O2) production, eliminating a dedicated CO2 scrubber by incorporating its function in the spaces of the respirator’s breathing loop and storing O2 in a liquid form with long standby capabilities. When these technologies are applied to a future design, there is the possibility of having an escape respirator that can be belt worn and capable of being certified to 42 Code of Federal Regulations (CFR) Part 84 standards, including sub-part O for escape purposes including mine escape. BACKGROUND NIOSH NPPTL has a Research and Development effort to provide mine workers with state-of-the-art breathing air technologies to comprehensively support initial and continued self-escape, refuge alternatives, and rescue needs, resulting from mine emergencies. As part of this R&D effort, NIOSH invested in the development of a next-generation closed-circuit mine escape respirator (CCMER) which would be compliant with NIOSH’s respirator standard requirements, 42 Code of Federal Regulations Part 84, including sub-part O. The design features of the CCMER also address the MINER Act’s requirements for transitioning between devices without the need for doffing the initially donned device. It would also allow for improved protection when using voice communications with a donned device ."

Jan 1, 2018

By S. F. Kaplan, A. S. Dolotov, V. N. Kovalev

"The proportion of refractory sulphide ores and concentrates in world gold mining industry is growing every year. Pressure oxidation of these materials (in autoclave) allows to oxidize gold hosting minerals. Traces of halides and pseudohalides present in the slurry liquids contribute to formation of complex gold compounds. Sorption-active carbon present in ores leads to irreversible adsorption of complex gold compounds and their loss. The objective of the research is to study gold extraction dependence on the concentration of chloride-, cyanide- and thiocyanate-ions in the slurry liquids during pressure oxidation. Double refractory flotation concentrate of the Bakyrchik deposit was used for the testwork. The research was planned on the basis of a full factorial experimental design with additional refining experiments. Ligand concentrations (0 – 1000 mg/l Cl-, 0 – 600 mg/l CN-, 0 – 1200 mg/l of SCN-), temperature (200 – 240 °?) and retention time (1 – 6 h) were used as variables of pressure oxidation process. It was determined that sulfide minerals oxidize much faster than ""organic"" carbon. Under the conditions of T = 240 ?C, t = 2 h, sulphide sulfur oxidation was 95.6%, while ""organic"" carbon oxidation was 46.1 %. Each of the examined ligands has a significant adverse impact on gold extraction. Analysis of the experimental data demonstrated that with a high degree of confidence (R2 = 0.883) gold extraction does not depend on the ligand type, but only on its concentration and the ""organic"" carbon oxidation degree. In case of complete oxidation of ""organic"" carbon, the presence of the ligand (L = Cl-, CNS-, CN-) in the liquids at a concentration of up to 20 millimole/L does not significantly affect gold extraction. The assumption that the main factor of preg-robbing in ???-CIL treatment of double refractory concentrates is the natural ""organic"" carbon sorption-active to gold has been confirmed. INTRODUCTION In recent decades, placer gold mining has been gradually declining and hardrock gold mining, including ""refractory"" gold mining, has been growing all over the world, as well as in the Russian Federation (http://www.miningworld.ru, 2015). One of the main reasons why gold ores are refractory is gold adsorption on natural carbonaceous materials (""organic carbon""). Only a few technologies are suitable for processing such ore concentrates (a significant amount of gold is contained in refractory hardrock ore both in Russia and worldwide) (Vorob'yev-Desyatovskiy N.V., Yepifanov A.V., 2014)."

Jan 1, 2018

By G. Mucsi, F. Kristály, Á. Rácz, É. Gregus, K. Bohács

"Stirred media mills are widely used in the industry for fine grinding. Most of the applications work in wet mode, however dry grinding in stirred media mill comes forward more frequently nowadays. The present paper deals with the differences and similarities of the wet and dry grinding in stirred media mill from energetic and mechanochemical point of view as well. Grinding experiments in batch stirred media mill were carried out with different materials. During the experiments zeolite and kaolin were used as feed material. The grinding experiments were carried out at different stress energy and stress number values; the grinding work was measured during milling. After grinding X-ray diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), particles size analyzes by laser scattering were carried out on the ground materials. As a result of the systematic grinding and analytical measurements a comprehensive comparison was carried out on the wet and dry grinding and their usefulness for mechanical activation in stirred media mill. INTRODUCTION The natural zeolites are crystalline hydrated aluminosilicates of alkali and alkaline earth characterized by the structure that contains frameworks responsible for the high cation exchange capacity (CEC) and absorption capacity. The frameworks are interconnected by cavities and resided by cations variable in size, coordinated by water molecules. Since zeolite comprises SiO4 and AlO4 tetrahedra interlocked by oxygen atoms that are situated in the structural nodes, their characteristics differ due to the varieties in the structure-directing agents and Si/Al ratio (Colella and Wise, 2014; Malekian et al., 2011; Terzic et al., 2017). The most common natural zeolite occurring in high amount, of industrial importance and involved in milling and MA is the clinoptilolite, in the literature equivalent to “natural zeolite” designated for high clinoptilolite bearing volcanic tuffs. Its amount in the host rock must reach ~ 40 % by weight to obtain the CEC and adsorption desired in its applications. In the highest quality rock might reach 80-90 % by weight (Favvas et al., 2016), but most often is the 40-60 % by weight content, associated with smectites, improving the CEC and adsorption of the tuffaceous rock. The application of such natural zeolites is problematic in many cases due to high silica (quartz, cristobalite and volcanic glass) content and beneficiation (concentration and extraction of pure zeolite) are not feasible. Thus, mechanical activation is a possible way to alter the other than clinoptilolite minerals generating high specific surface area and functionalized particle surfaces to enhance adsorption, reaction or particle adhesion. The zeolites easy availability and the utilization cost-effectiveness have prompted the research on their physicochemical and structural properties (e.g. adsorptive and molecular-sieve activity, heat resistance, and microporous cage structure) and finding new options for their application (Kusuma et al., 2013; Musyoka et al., 2014; Rida et al., 2013; Terzic et al., 2015b). Apart from the presence of exchangeable framework cations which are crucial for the adsorption ability, and a certain degree of pozzolanic reactivity. The thermal stability of dehydrated phases is another important characteristic for use of the zeolite in composite materials that are exposed to high temperature. Thereby, the zeolites found a wide application possibility in the design of the construction composites (Albayrak et al., 2007; Najimi et al., 2012; Vejmelková et al., 2015), as well as for resolving of the environmental protection issues like wastewater refining or heavy metal elimination (Gómez-Hortigüela et al., 2014) even from contaminated groundwater using passive methods like permeable reactive barriers (Gombköto et al, 2016). The grinding treatment of zeolite is a common and frequently applied procedure, both on laboratory (Bohács et al. 2017, Faitli and Czél, 2014)"

Jan 1, 2018

By M. Evertsson, M. Johansson

"In minerals processing control is vital to increasing performance and output of a plant. Model predictive control (MPC) is one of the most effective control strategies used in process industry. Sbárbaro (Sbárbaro and Del Villar, 2010), Asbjörnsson (Asbjörnsson, 2015), and Légaré (Légaré et al., 2016) have for example highlighted the possibility to simulate, develop and tune control systems using plant simulators within minerals processing. In more recent years the use of model predictive controllers have increased, and many process industries now utilize more advanced control methods to regulate their processes, raising the question regarding how to, build, test and verify a proposed control solution successfully. In this research, a linear model predictive controller is formulated and applied to a simulator of an existing tertiary crushing circuit. The circuit has in previous work by Johansson (Johansson, 2017) been modeled in MATLAB Simulink and calibrated relative plant data to an average error of less than 10% over 8 hours of production. The work demonstrates how to formulate the controller model structure to describe conveyor belts, storage components, screens, crushers, and control objectives for a minerals processing circuit. The work illustrates how to apply and successfully evaluate possible upsides in a circuit. The advantage of a crushing circuit simulator is that it can be configured, tuned and modified in any possible way, which is of great benefit to developers and engineers. Additionally, examples of how to use estimated measures to improve the performance of the plant are demonstrated. The control performance is finally evaluated for three different controller configurations."

Jan 1, 2018

By Thi Hien Tran, Huy Hoan Nguyen, Thi Thu Hien-Dinh, Hong Son Nguyen, Duy Anh Dao

"Lithium discovered in La Vi deposit, Quang Ngai province in the Central of Vietnam was estimated with a reserve of approximately 1.5 million tones of lithium ore, which was characterized by mainly lepidolite with muscovite, albite, and quartz. This study investigated reasonable flowsheet and optimal conditions of enrichment technology for lepidolite from the mined ore by flotation process, and producing Li2CO3 and LiCl from lepidolite concentrate by hydrometallurgical process. The significant conditions for froth flotation of lithium ore including particle size, pH of ore slurry, pulp density, chemical spending (collectors, activators, depressants, and frothers), stirring and flotation time were investigated. The identified reasonable flowsheet and optimal conditions for froth flotation the La Vi lithium ore processed lepidolite concentrate containing up to 4 wt.% Li2O with a recovery of 87.61 wt.%. The processes of sulfation roasting lepidolite concentrate using FeSO4.7H2O, then leaching in H2SO4 solution, and removing impurities were carried out to prepare a pure lithium-bearing solution for producing Li2CO3 and LiCl. The products containing 99.05 wt.% of Li2CO3 and 99.02 wt.% of LiCl were obtained with recoveries of 82.97 wt.% and 85.77 wt.%, respectively. The obtained results indicated that lithium ore in La Vi deposit can be processed to produce commercial lithium products and lead the study to develop technology for a new industry of lithium processing in Vietnam.INTRODUCTION Lithium is the lightest metal, which has many superior properties in both metal and compound (such as Li2CO3, LiCl...) states since its discovery in 1817 by Swedish chemist Johan August Arfwedson. Lithium is a favourable material for many high technology fields such as aerospace industry and chemical industry. Some industrial fields which present the main consumptions of lithium include ceramic, glass, aluminum alloy, lubricants, rechargeable Li-ion batteries, synthetic rubber, and pharmaceuticals. The worldwide production of lithium in 2014 was 31,700 tones, continually increased in 2015 of 5% presented 32,500 tones (USGS, 2016). The demand for lithium tends to increase because of the raising in consumption of lithium batteries. Lithium is mined from salar brines, mainly in Chile and Bolivia, but also from granites and pegmatites, which contain minerals with high lithium content such as spodumene - LiAlSi2O6 (Heinrich et al., 1978; Linnen et al., 2012); petalite - LiAlSi4O10 (Sitando & Crouse, 2012); zinnwaldite - KLiFe2+Al(AlSi3O10)(F,OH)2 (Paukov et al., 2010; Kondás J. & Jandová J., 2006); lepidolite - K(Li,Al)3(Si,Al)4O10(F,OH)2 (Luong et al., 2013); and amblygonite - LiAlPO4F (Garrett, 2004)."

Jan 1, 2018

By J. Wiese, K. Corin, Z. Song

"Relating flotation performance to the electrochemical characteristics of a pulp is complex both in fundamental research and in practice. In the case of thiol collectors, different Eh values in the flotation system can result in the formation of the dimer or the metal thiolate which may or may not enhance the hydrophobicity of the mineral. Reducing or oxidizing conditions in a flotation system, viz. changing the Eh value, are usually manipulated to achieve an optimum flotation response by control of pH and dissolved oxygen levels in the system. A variation in pulp potential may also be achieved by the addition of potential modifiers such as sodium hydrosulphide (NaHS), sodium hypochlorite (NaClO) or hydrogen peroxide (H2O2). There exists anecdotal evidence which suggests that the addition of small amounts of H2O2 to the flotation process can improve sulphide mineral recovery. The objective of the present study was to investigate the effect of the addition of the potential modifier, H2O2, on sulphide mineral recoveries and grades in the flotation of sulphide minerals from two copper bearing ores from China and compare the results to those obtained for a PGM bearing ore South Africa. Batch flotation tests were conducted using the three different ores at the natural pH of the different systems, in the presence of a xanthate collector and the absence and presence of H2O2 as a potential modifier. The results indicate that the addition of carefully controlled low concentrations of H2O2 resulted in improvements in flotation performance. INTRODUCTIONElectrochemical potential as a control parameter in the flotation of sulphide minerals has been widely studied (Allison et al., 1972; Gardner and Woods, 1979; Ross and Van Deventer, 1985; Chander, 2003; Woods, 2003; Javadi, 2013). There is concensus that in order to be recovered during flotation, sulphide minerals require a suitable redox environment. During the flotation process thiol collectors and sulphide minerals are involved in electrochemical reactions which result in the formation of hydrophobic species at the mineral surface (Finkelstein and Goold, 1972; Rand and Woods, 1984). Sulphide minerals act as semiconductors and electrons are transferred during the interaction of the mineral with collector. The resultant potential difference and its magnitude are responsible for the transfer of electrons and the rate of the reaction (Bard and Faulkner, 2001; Fuerstenau et al., 2007). Reducing or oxidizing conditions in a flotation system, viz. changing the Eh value, may be manipulated to achieve an optimum flotation response by control of pH and dissolved oxygen levels in the system (Heyes and Trahar, 1979). The use of potential modifiers viz. reducing or oxidizing agents which include H2O2, NaClO, and NaHS, is an alternative method by which to control the potential of the pulp in a flotation system which may or may not promote the flotation of desired minerals (Rao, 2004). The oxidizing agent, H2O2, undergoes a cathodic reaction which can result in the enhanced flotation of valuable minerals. The potential of the system is increased which results in a shift in the mixed potential of a mineral. The magnitude of the over-potential influences the rate of the oxidation process and thus the flotation response of sulphide minerals (Kocabag and Guler, 2008). Equation 1 shows the proposed oxidation of xanthate by H2O2 (Lipkina and Streltysn, 1970)."

Jan 1, 2018

By D. Murray

"The Mine Improvement and New Emergency Response (MINER) Act included the need for improved chemical technologies to address respiratory protective device inadequacies and refuge alternative development. The National Institute for Occupational Safety and Health’s (NIOSH) National Personal Protective Technology Laboratory (NPPTL) invests in research and development to improve the carbon dioxide (CO2) scrubbing technologies built into these mine safety systems. Testing at NIOSH NPPTL is performed using a custom-designed test system containing a chemical reactor and sensors in a constant flow of simulated expired breath to evaluate chemical performance for the scrubber materials. Current testing procedures focus on device duration or capacity, but do not report criteria needed to effectively optimize chemical performance. In this presentation, testing results which identify the chemical performance roles for CO2 scrubber components will be reported, and specific component chemical activities will be linked to both duration and CO2 absorption capacities. Chemical components being evaluated include hydroxyl, superoxides, metal, and amine active sites, distributed in salts, zeolites, metal-organic frameworks, and microporous materials. INTRODUCTION CO2 absorbents and oxygen sources are at the heart of closed circuit breathing air supply systems used in mining escape and rescue operations. CO2 absorbent technology was first developed for diving rebreathers and has been in use for over a century. Typically these devices include a soda lime formulation of pellets in the 8-12 mesh range. Larger 4-8 mesh particles are used in medical grade “low-flow” applications, since these particles present a lower flow resistance regime more amenable for use with resting individuals. Potassium superoxide and lithium hydroxide formulations are also used, where in each case the formulations involve bulk solid pellets or materials affixed to surfaces. CO2 capture technologies are now under intensive study in the energy and automotive industries, where the pursuit of optimal combustion processes has led to the development of new materials to capture, convert and store CO2, oxygen and carbon monoxide gases. Recent advances in nano-structured and high surface area catalysis have produced novel materials demonstrating chemical performance improvements in these industries, and these improvements may now also be adapted to enhance chemical efficiency and performance in escape and rescue devices. Higher surface area materials offer promise for improving the efficiency, or decreasing the burdens associated with the use of closed circuit respiratory protective devices containing CO2 absorbents. Novel chemicals that display advantages in chemical performance or decreased burden will be examined for inclusion in developing systems such as the next-generation closed-circuit mining escape respirator or refuge alternatives."

Jan 1, 2018

By Jingzhong Kuang, Zheyu Huang, Chuanzhou Guo, Pengfei Liu

"In this paper, scheelite and scheelite coated with Pb2+ (SC) were synthesized by chemical precipitation with the help of ultrasonic. The role of the Pb2+ on scheelite was evaluated. Additionally, the dissolution behavior of minerals and the adsorption mechanism of collectors were investigated systematically via SEM, XRD, EDS. The results indicate that the ultrasonic cavitation can promote the formation of scheelite with large particle size and high crystallinity. Due to the exchange of WO4 2- and OH-, the dissolution of scheelite are not in a 1:1 equivalent amount by chemical formula and the concentration of WO4 2- is higher than that of Ca2+ in the solution because Pb2+ promotes the transfer of WO4 2- from scheelite surface into the solution. The dissolution of scheelite is an endothermic reaction and its enthalpy reaches the maximum value of 692.59J·mol-1 at pH=8~10. But the coating of Pb2+ changes the thermal effect of scheelite in the solution and the dissolution of SC is an exothermic reaction with the dissolution enthalpy of -262.30 J·mol-1. At pH=8~10, the adsorption capacity of sodium oleate and salicylhydroxamic acid on the surface of SC is higher than that of scheelite which delivers that Pb2+ contributes to the scheelite surface dissolution and enhances the adsorption of collectors on the mineral surface, thus achieving activation.INTRODUCTIONIn modern society, tungsten is a type of quite important rare metal and also a strategic resource. Because of its low vapor pressure, high melting point, good electrical and thermal conductivity properties, it is widely applied in high-temperature technology, lighting, machine and engine construction (Zhao,Z.W, 2013; Yan, W, 2017; Ilhan, S, 2013). Both scheelite and wolframite are the major tungsten deposits. With the depletion of easily-processed wolframite, scheelite has drawn a great deal of scientific and industrial attention. Scheelite can be recovered by flotation due to the metathesis of polarity and chargeability on minerals surface via adding regulators and collectors."

Jan 1, 2018

By M. J. Collins

"Autoclaves were first used in the metallurgical industry in 1893 to recover alumina from bauxite. In the 1940s and 1950s, several high temperature and pressure processes were invented in the laboratory of Professor Frank Forward at The University of British Columbia, in parallel with advances in equipment and processes by the Chemical Construction Corporation. Sherritt Gordon Mines Limited enlisted these groups to help develop the nickel sulfide ammonia leach process that was commercialized in 1954. Autoclave processes that have since been commercialized include high-pressure acid leaching of laterites, zinc pressure leaching, and pressure oxidation of refractory gold feedstocks. RÉSUMÉ En 1893, l’industrie métallurgique est la première à utiliser les autoclaves pour l’extraction de l’alumine dans la bauxite. Dans les années 1940 et 1950, plusieurs procédés à haute température et à haute pression sont inventés dans le laboratoire du Pr Frank Forward de l’université de la Colombie-Britannique (UBC) ; parallèlement, la Chemical Construction Corporation fait de grands progrès en matière d’équipement et de procédés. Sherritt Gordon Mines Limited fait appel à ces groupes pour qu’ils aident la société à développer le procédé de lixiviation du sulfure de nickel dans de l’ammoniaque, commercialisé en 1954. Les procédés de lixiviation en autoclave commercialisés depuis incluent notamment la lixiviation acide à haute pression de latérites, la lixiviation sous pression du zinc et l’oxydation sous pression des matières premières de l’or réfractaire.INTRODUCTION Autoclaves are chemical reactors that are built to contain processes taking place at elevated pressure. They are used in metallurgical refineries throughout the world to take advantage of the increased reaction kinetics and different reaction products that can be obtained in aqueous systems above the boiling temperature at atmospheric pressure. The word autoclave comes from the French “auto” and the Latin “clavis” and literally means self-locking—that is, the core distinguishing feature of an autoclave is that it includes a means for pressure regulation (e.g., a pressure relief valve). Denis Papin (Figure 1a), one of the inventors of the steam engine, was the first to make use of a safety valve to control steam pressure. He is credited with inventing the autoclave in 1679. Papin’s “digester” (Figure 1b) was a type of pressure cooker that was originally used to liquefy bones. Most commercial autoclaves are horizontal, multicompartment vessels with mechanical agitation, as shown in Figure 2a; however, the steam-agitated Pachuca vessels used to leach laterite ore in Moa, Cuba (Figure 2b), are also classified as autoclaves according to the self-locking definition provided above."

Jan 1, 2018

By W. R. Reed, S. Klima, J. Driscoll, T. W. Beck

"Tests were conducted to determine properties of four foam agents for their potential use in longwall mining dust control. Foam has been tried in underground mining in the past for dust control and is currently being reconsidered for use in underground coal longwall operations in order to help those operations comply with the Mine Safety and Health Administration’s lower coal mine respirable dust standard of 1.5 mg/m3. Foams were generated using two different methods. One method used compressed air and water pressure to generate foam, while the other method used low-pressure air generated by a blower and water pressure using a foam generator developed by the U.S. National Institute for Occupational Safety and Health. Foam property tests, consisting of a foam expansion ratio test and a water drainage test, were conducted to classify foams. Compressed-air-generated foams tended to have low expansion ratios, from 10 to 19, with high water drainage. Blower-air-generated foams had higher foam expansion ratios, from 30 to 60, with lower water drainage. Foams produced within these ranges of expansion ratios are stable and potentially suitable for dust control. The test results eliminated two foam agents for future testing because they had poor expansion ratios. The remaining two foam agents seem to have properties adequate for dust control. These material property tests can be used to classify foams for their potential use in longwall mining dust control. IntroductionAbout one-half of U.S. underground coal is produced by longwall mining, which allows for mining high volumes of coal but generates significant amounts of coal mine dust. This can lead to overexposures for longwall miners and possibly occupational respiratory diseases, including black lung and silicosis, which have no cure and can be disabling or fatal. The only method to avoid these occupational illnesses is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit for respirable coal mine dust is 1.5 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities (Mine Safety and Health Administration (MSHA), 2015a). When respirable quartz is present, the mine must maintain average concentrations at or below 0.1 mg/m3. If the mine exceeds the 0.1 mg/m3 respirable quartz dust concentration, then the applicable respirable dust standard is reduced, calculated as 10 divided by the percent quartz present (MSHA, 2015b)."

Jan 1, 2018

"Australia’s largest rail freight network operator, the Australian Rail Track Corporation (ARTC), has selected GE Transportation’s Movement Planner solution as the key technology enabler for its Hunter Valley-focused network control optimization program.ARTC’s Newcastle-based network control, is the nerve center of Hunter Valley rail operations, where locally based train control professionals make thousands of decisions every day to safely support the annual movement of more than 24 kt/h (26,400 stph) of freight, and tens of thousands of coal, freight, grain and passenger trains each year.ARTC plans to transform its train control function by integrating and then building on Movement Planner, an advanced software solution by GE Transportation that provides real-time rail traffic planning and optimization to enable freight to move more efficiently. “The Hunter Valley rail network is one of the busiest and most complex in the country, supporting the largest coal export port in the world,” ARTC managing director and chief executive officer John Fullerton said.“As bulk freight demands grow, rail operators like ARTC and supply chains like the Hunter Valley coal network need to be creative in the way they respond so the Australian economy doesn’t miss out. That’s why we have conducted a worldwide search to find globally proven solutions that will improve our network productivity and efficiency,” Fullerton said.The Movement Planner solution considers multiple factors including train schedules, trafficcontrol systems and train movements relative to each other and then develops an optimized traffic plan for the trains throughout the network. Existing GE customers have benefited from increased visibility of network operations, higher velocity, less dwell times, and improved on-time performance across their networks."

Jan 1, 2018

By Ramin Motamed, Joseph A. W. Toth

Evaluation of the capacity of large-diameter drilled shafts using current load test methods present challenges when considering the magnitude of loads required to fully mobilize their capacities. Often, these full scale tests do not fully mobilize the capacity through side resistance. Therefore, the need for innovative solutions to extrapolate side resistance and interpret nominal capacity are of key interest. In this study, we evaluate three methodologies for extrapolating unit side resistance based on bi-directional load test data. Fellenius (2001) presented these methods for interpretation of pile capacity using static load tests. Our interpretations are based on the evaluation of 116 load tests. Unit side resistance was calculated and reviewed for each load test and categorized using three criteria of mobilization; (A) full, (B) partial and (C) linear. This study specifically focuses on load tests that showed fully mobilized unit side resistance behavior (Criteria A). The three methodologies were applied assuming Criteria (A) load tests were mobilized to 50% of their measured values. Subsequent comparisons of each extrapolation were then compared against the full measured values for each test and generally showed good agreement. INTRODUCTION It is widely accepted that conducting load tests such as standard top-down tests or bi-directional (i.e. O- cell) tests can help designers understand load-settlement behavior and the nominal resistance of drilled shaft foundations. These load testing methods provide the advantage of confirming design assumptions as well as improving the reliability of the foundation design. The potential cost savings from the application of these methods for mid to large size projects is self-evident. For example, in a recent project in Northern Nevada, an O-cell test on a 6.9 ft diameter, 114.8 ft length drilled shaft imposed an initial cost of $125k to the project, resulting in a 15% reduction on the total foundation cost; equivalent to $1.3 million in overall savings (Pease, 2014). However, the costs of implementing such methods on smaller projects can be prohibitively expensive (Hagerty et al, 2016). Despite the clear advantages of drilled shaft load testing, the current practice is not without limitations. Performing load tests on large-diameter drilled shafts with high capacities is a challenge considering the significant loads required to fully mobilize the capacity of such foundations. In some cases, the feasibility of these tests is impractical because the associated initial cost is not guaranteed to outweigh the final savings. As a result, large scale load tests are sometimes ruled out from the design phase of projects. Furthermore, in the majority of load tests the magnitude of loads applied are specifically selected to not approach failure, so the shafts can be used in the future foundation system (i.e. production shafts). This practice of field testing restricts our knowledge of the true capacity of the drilled shaft at failure; hence the nominal resistance remains unknown.

Jan 1, 2018

By O. V. Suvorova, V. G. Minenko, D. V. Makarov, A. L. Samusev, E. A. Selivanova

"Saponite is a valuable marketable product widely used foundry, metallurgy and construction, in the chemical, food and consumer goods industries, in medicine, and in agriculture.The feasibility of producing of high-quality construction materials with enhanced physical-chemical and decorative characteristics from saponite-containing products has been given a scientific basis and experimentally validated. The compressive strength of the samples in the sintering temperature range of 800-1000 ?? varied between 35 and 80.9 MPa; the bending strength 8 and 26.7 MPa, which is superior to the high-grade ceramic bricks of the M-300 brand. It has been established that the saponite-containing product obtained using the electrochemical separation of process water has a high sorption capacitance relatively the heavy-metal ions such as nickel and copper (40.7 and 99.8 mg/g, respectively). As a result of sintering at 750 ?? the sorption capacity of the sorbent for the nickel and copper ions increased to 194.2 and 212.8. Using the XRD and SEM with energy-dispersive spectroscopy studies, we diagnosed the metal-containing phases and validated the metal sorption mechanism.This study opens up the possibility of practical realization of the saponite-containing product as high-quality building materials and heavy-metal sorbents while addressing the issue of process water treatment. INTRODUCTION The Lomonosov deposit of the Archangelsk diamondiferous province accommodates 10 kimberlite pipes. The anticipated volume of diamond-bearing ore and dump rock to be removed before reaching the open-pit mining limit is 300 mln t (Karpenko, 2009; Bezborodov, etal. 2003). Rock in the deposit is almost completely displaced by clay minerals, predominantly saponite, amounting to 90% in the vent facies (Karpenko, 2009)."

Jan 1, 2018

By B. A. Kutlin, S. A. Ropeyko, N. A. Yurlova

"The aim of NPO RIVS research and practice activities is to minimize impact of the mineral processing plants (MPP) on environment by using new concentration methods, high-technology equipment, implementation of engineering solutions directed to reduce emission of polluting substances (PS) into atmosphere, application of low-waste technologies, decrease of water withdrawal from a surface water or groundwater source for process needs. In our studies environmental safety of mineral flotation is provided through technologies using highly selective chemicals, that leads not only to reducing reagent consumption, and production of saleable products of high content of extracted minerals, but also to reducing pollutant emissions, decreasing supply of surfactants (SAA) in natural geosystems, primarily, in ground and surface waters. Decrease of water withdrawal from a surface water or groundwater sources for process needs can be achieved by using closed circuits and waste water treatment for further use in process operations, recycled water conditioning to obtain optimum quality parameters for process operations of concentration. Concentration in water (wet processing), tailings dewatering and semidry and dry (filtration cake) stockpiling in tailing ponds, efficient dust-collecting systems contribute to pollutant emission reduction. Use of mineral wastes – concentration tailings as a source of valued components, facilitates efficient use of natural resources and reduces wastes and its impact on natural ecosystems due to smaller areas of damaged lands during waste products disposal. Process and engineering solutions of NPO RIVS that allow diminishing impact of MPP on natural environment (NE) have been implemented in mining and processing complexes of Russia, Kazakhstan, Ukraine, Kirghizia and Mongolia. Compliance with environmental safety requirements contributes to enhancement of mineral processing and sustainable mineral development.INTRODUCTION Mining and processing complexes have a significant impact on environment as a result of extraction and recovery of mineral resources, landscape changes, waste disposal and, as a consequence, pollution of soils, surface and underground water sources. Therefore, the aim of the operation of the mineral processing enterprises in its research and practical activities is to reduce impact on environment due to new beneficiation technologies, high-technology equipment, implementation of engineering solutions directed to reduce emissions of polluting substances (PS) into atmosphere, use of low-waste technologies, decrease of water withdrawal from a surface water or groundwater source for process needs. Compliance with the requirements of environmental safety encourages advancement of mineral processing technologies and sustainable mineral development. Concentration in water, tailings dewatering and semidry and dry (filtration cake) stockpiling in tailing ponds, efficient dust-collecting systems contribute to pollutant emission reduction. Use of mineral wastes – concentration tailings as a source of valued components, facilitates efficient use of natural resources and minimizes waste formation and its impact on natural ecosystems due to reduction of damaged land areas during waste disposal."

Jan 1, 2018

By Martin Langenderfer, Catherine Johnson, Phillip Mulligan, Kelly Williams

The physical geometry of a charge has a direct correlation to the geometry of the shock wave. This relationship appears strongest within the boundaries of the visible fireball. As the shock wave propagates outward past the limits of the fireball, the theory states that the geometry of the shock wave should even out and become more spherical. This paper investigates pressure vs. time at two distances, one ‘Near Field’ at the extent of the fireball and one ‘Far Field.' The two Fields were instrumented with three free-Field pressure probes from PCB oriented at 0, 45, and 90 degrees to the front face of the charge, in the same horizontal plane as the charge. This orientation allows for the comparison of the shock wave from the face and vertices of the charge. All the pressure sensors were connected to a Data Acquisition System (DAS) recording at 2 million samples per second (2MS/s). Two high-speed cameras, a Phantom and an MREL Ranger II, recorded the detonations for qualitative examination of the fireball, and the shock wave. Three charge geometries were used and compared to the shock propagation of a sphere. The other geometries tested are cylinders, cubes, and tetrahedrons. Charges were made from a PETN based sheet explosive. In the Near Field, a lower pressure is observed along charge vertices with highest pressures from each face. In the Far Field, vertices record a higher pressure, possibly due to the shock waves from the adjacent faces intersecting, indicating that shock pressures do not always even out in the Far Field. This paper will describe the methodology and findings of this experiment and attempt to determine causality for trends in the data gathered.

Jan 1, 2018

By M. Gonzalez Fernandez

"Commercially introduced in 2004, the SAGDesign™ test has today proved its efficiency for sizing SAG mills for a wide variety of ores, from very soft to very hard ones. The interest of building a model using the SAGDesign™ test specific energy is the introduction of such a model into a complete process simulator making it possible to predict a complete material balance. The developed model compares the required specific energy with the energy provided by the mill. This energy calculation is derived from the Austin Power Formula. The specific energy provided by the test is corrected, using various parameters, such as the Ball Mill Work Index, to take into account the true operating conditions, the feed and product sizes. The core of this model allows the determination of the product d80 using the mill geometry, its operating conditions and of course the SAGDesign™ test results. To be included in a simulator, the model must also predict the overall size distribution of the SAG mill discharge. Assumptions to answer this point are presented here. The model has been implemented in the USIM PAC simulator. It is used either to predict the product size distribution for a given SAG mill, but also to size a SAG mill for getting a required reduction ratio. INTRODUCTION Over the last few years several types of new comminution machines have been introduced in the market. The most notable newcomer was the HPGR (Morley, 2006). But, even when these machines have some advantages, they have not earned the trust of the mining industry. That is why the established technologies still being the first choice. And, in comminution, that first choice are SAG and ball mills. The design of ball mills has been well understood for a long time. The Bond Ball Mill Work Index is the standard test which helps to describe the ore in terms of energy requirements for milling. Unfortunately, the development of an equivalent test to characterize the ore subject to SAG milling has taken some time. As of today, several tests are available in the market, like the MacPherson test, the MinnovEX SAG Power Index (SPI™), the JK Drop Weight Test, the SMC Test® and the SAGDesign™ test (Verret et al., 2011). The SAGDesign™ test, developed by John Starkey in Canada in the early 2000s (Starkey et al., 2008, 2015), has become one of the standards to assess the grindability of an ore in a SAG mill. One of its advantages is the reduced sample mass needed to perform it, hence, the reduced cost. The second one is that the output of the test is straightforward, it is the energy required to grind the ore between two sizes. Because of this energetic approach, the results provided by the test can be directly applied to size a new mill or to assess the performance of an existing mill."

Jan 1, 2018

By Richard Harrison, Frank Lim

Deepsea Mining will soon become a reality with Nautilus Minerals getting their equipment ready to mine SMS at Solwara 1 off the coast of Papua New Guinea. The vertical transport system (VTS) adopted by Nautilus consists of a riser hanging ‘freely’ from the mining production vessel with a lifting pump unit suspended at its lower end. A compliant jumper connects the pump to the seabed crawler without restraining its movements. In this free-hanging VTS arrangement, the vessel can be re-positioned to follow the crawler should it want to extend the mining area and start stretching the jumper. A recently proposed alternative to this is a free-standing VTS whereby the riser is grounded on the seabed with a base and maintained in an upright position by distributed buoyancy modules or a buoyancy tank at the top. A compliant jumper connects the seabed crawler to the riser base, and another connects the riser top to the vessel. In this free-standing arrangement, the entire VTS can be lifted clear of the seabed for relocation to a new mining area. This paper will describe the important features of the two options and discuss the advantages and disadvantages in respect of riser dynamic behavior, water depth, weather and mining windows, pump maintenance, installation and retrieval, continency measures, etc. The two systems will also be appraised separately for mining SMS and SMnN deposits.

Jan 1, 2018