Search Documents

By A. S. Broesder

"With depletion of global ore deposits, there has been an increasing industry trend towards mining of lower average grade deposits in order to meet global demand, resulting in increased processing cost, energy usage and water usage. Consequently the industry is seeking pre-concentration technologies to reduce costs, increase production in existing operations and potentially enable the economic mining of previously uneconomical deposits. This pre-concentration can also advantage downstream processing and metal recovery. CSIRO has developed a large scale magnetic resonance based technology for the rapid quantitative detection of selected copper, iron and arsenic minerals in bulk ore. The technology is suited to measurement on large primary conveyors for enabling “pod” based sorting. The approach used in high tonnage sorting is to not sense and divert individual rocks, but to instead measure groups of rocks (“pods”) carried continuously on a single primary conveyor that can be diverted by conventional mechanical means. Bulk ore sorting operates by removing barren ore pods from a stream of crushed ore based on a bulk sensor measurement at a pod resolution of ~1 – 10 tonnes. The sorting process is based on the intrinsic variability of grade during the mining process that often occurs at the few tonne scale, and for instance, is common in many porphyry copper deposits. The MR technology has been proven in the laboratory for a wide range of copper, arsenic and iron minerals. A full scale prototype sensing system has been demonstrated in a trial at an Australian copper mine. Implementation trials of commercial MR based bulk sorting systems are progressing during 2018.INTRODUCTION An increasing trend in the mining industry is the exploitation of larger lower-grade deposits to meet global demand. Low-grade deposits involve increased processing cost, energy and water usage and increased tailings. There is therefore growing interest in technologies that enable more efficient extraction of low grade deposits. Water intensity of mining activities in a context of water scarcity, and the environmental and health implications of mine tailings are existing challenges, which are only made worse by the progression to lower grade orebodies. There is therefore also an interest in safer, cleaner and less wasteful extraction and production to ensure community well-being and environmental resilience."

Jan 1, 2018

By T. Wallmach, S. B. Blancher, A. Delaporte, P. Goncalves

"Fe-Ti oxides concentrates produced from heavy mineral sand deposits are widely used for the production of titanium dioxide pigments that are critical components of white paint, plastics and paper. According to mining industry, the Fe-Ti concentrates mostly consists of three phases: ilmenite, leucoxene and rutile. However, a few mineralogical studies have shown that the variety of Fe-Ti oxides found in sand deposits is far more complex, mostly due to alteration processes. The aim of this contribution is to characterize in detail by means of Qemscan analyses the mineralogy of the three main concentrates (ilmenite, leucoxene and rutile) produced by the Grande Côte Operation (GCO) mineralurgical plant in Senegal. The ultimate goal is to characterize the different products and textures formed during the natural ilmenite alteration processes, to localize the phases carrying the main impurities (Cr and P), and finally to determine the physical properties of each mineral component to improve metal recoveries. Along alteration processes, Ti content increase. Ilmenite (FeTiO3) is progressively transformed into pseudorutile (Fe2Ti3O9) particles which could also be altered and transformed into hydroxylian pseudorutile [FeTi6O12(OH)3.3H2O] or complex blends of anatase microcrystals (TiO2). These transformations are accompanied by significant changes in particle textures. Microporosity and fractures appear and the impurity content also increases. Anatase rich microcrystal assemblages, so far described as Leucoxene, could be identified to consist of grains with higher porosities, water contents and higher intrapore impurities. These particles are the main carriers of chromium and phosphorus. The observed mineral transition textures have a significant impact on the ore dressing processes. During these transformations, the physical properties of these phases change, the magnetic susceptibility as well as densities decreases, due to the increase in porosity. The separation of particles, especially those with high porosity will help improving the GCO mineralurgical plant performance and to reduce the impurity contents in finals products."

Jan 1, 2018

By Boqiang Wu, Ganggang Xu, Xiaodong Wang, Hai Wang, Shibin Zhu

"Using a paste-like slurry as a filling from the ground surface to the goaf, artificial pillars can be built in the cavity goaf to support the goaf roof to prevent roof collapse and ground subsidence. If the accumulation laws of paste-like slurry are known well, the filling technology can be optimized. The laws can establish the foundation for finding out the best methods for building artificial pillars and filling technology. In order to understand the accumulation laws of paste-like slurry in the cavity goaf, Aeolian sand with wide distribution in northwestern China was selected as aggregate, and Portland cement was used as cementitious material to prepare a paste-like slurry. A test model of the cavity goaf was built to simulate the filling process by pump from the ground surface to the goaf to study accumulation laws of the paste-like slurry. The results show that the whole process of expansion and accumulation of the paste-like slurry could be divided into stages: free expansion, fill tightening expansion, and stable expansion. The angle of repose of the accumulation body of the paste-like slurry is constant in the stage of stable expansion, and it is the final angle of repose of the accumulation body. The angle of repose of the accumulation body is highly relevant to the slump of the paste-like slurry, and it is unrelated to the distance between the floor and roof. Under certain conditions of the cavity goaf, reducing the slump of paste-like slurry is one of the effective ways to obtain cost-effective pillars.INTRODUCTIONA large number of cavity goafs of coal mines were left in northwestern China; they were formed in the mining process by room-pillar or strip mining. Safety coal pillars were used to support the roof to keep long-term stability in the goaf, so the ground subsidence was not obvious (Fu, Deng, and Zhang, 2011; Xie, 2014). With gradual weathering, destruction of coal pillars, or additional load from ground surface buildings and structures, there could be a risk of instantaneous collapse of the roof in the goaf. This would affect the safety of existing structures on the ground and adjacent mines (Qu et al., 2017; Li, Xiang, and Jia, 2011; Tan, Guo, and Zhao, 2016; Tan et al., 2017). For disaster prevention of the falling cavity goaf, the current common practice is full filling (Hu et al., 2008; Liu, Zhu, and Huang, 2015; Pan and Wu, 2010). However, for buildings and structures with lower deformation requirements, full filling is excessive. For example, it is acceptable for goaf treatment under general roads and industrial sites to control the maximum deformation and keep the deformation continuous (Liu, 2011; Liu, 2012)."

Jan 1, 2018

By N. Birbilis, S. Kairy, C. R. Hutchinson, D. Jiang, D. R. Feenstra, O. Gharbi

"Recent developments in metal-based additive manufacturing (AM) technology have generated considerable interest in multiple industries, owing to flexibility in design and the ability to produce final components in their net shape. The AM of high-strength aluminium alloys has not been widely explored, due to findings of undesirable microstructures leading to short fatigue life and poor fracture toughness; restricting the application of AM to lower strength aluminium alloys (with cast-like Al-alloy compositions) to date. Herein, aluminium alloy AA2024 (Al-3.6Cu-1.2Mg) was additively manufactured via selective laser melting (SLM), with the resultant microstructures and corrosion properties characterised and compared to wrought AA2024-T3. Microstructural characterisation was carried out using transmission electron microscopy (TEM), revealing SLM produced AA2024 included a population of ?-phase (Al2Cu) in preference to S-phase (Al2CuMg) typical of wrought AA2024. Additionally, the corrosion properties were investigated by potentiodynamic polarisation in a range of NaCl concentrations, whilst elemental corrosion rates were also determined (including for open circuit exposure conditions) and quantified in situ with an inductively coupled plasma mass spectrometer coupled with an electrochemical flow cell. Results revealed a significant improvement in the corrosion resistance, and elemental dissolution of AM prepared 2024 relative to wrought AA2024-T3.INTRODUCTION Aluminium alloys remain the preferred candidate materials in applications requiring a balance of low density and strength. The ability to produce net shape components from aluminium alloys has accelerated due to recent developments in metal-based additive manufacturing (AM) technology, including selective laser melting (SLM) and powder bed 3D printing. The AM of Al-alloys, including Al-Si-Mg (namely AlSi10Mg), has become widespread commercially in recent years. Alloys including AlSi10Mg offer reliable and reproducible production by AM, however such alloys (and variants thereof) are not high strength alloys. The pursuit of higher strength AM Al-alloys presents significant merit to multiple industries; however, such higher strength AM Al-alloys have not been widely studied to date. The solidification of high strength Al-alloys during conventional (casting) operations needs to be executed in a manner that avoids so-called =hot-tearing‘, which can arise as a result of the solute type and loading. A report on the solidification of a high strength Al-alloy prepared by AM, along with factors related to solidification, was recently covered by Pollock and co-workers (Martin et al., 2017). It was reported that AM of high-strength aluminium alloys (which have to date been principally based on the compositions of wrought high strength Al-alloys) may lead to undesirable microstructures that reduce fatigue life and result in poor fracture toughness; presently limiting the application of AM to lower strength aluminium alloys (with cast-like Al-alloy compositions) to date."

Jan 1, 2018

By Dennis Sánchez Mora, John Jamieson

INTRODUCTION Work by Humphris et al., (2002); Ondréas et al., (2009); Barreyre et al., (2012); and Escartín et al., (2015) has identified active and inactive hydrothermal sites along the Lucky Strike segment. The sites that contain the largest accumulation of known sulfides are located between the north and the southern zones (Figure 1), a vent site area that is referred to as the Main Lucky Strike hydrothermal field (Escartín et al., 2015). Hydrothermal fluid outflow has been linked to a shallow fault network (Barreyre et al., 2012). However, specific constraints on fault geometries have not been determined. Other off-axis sites at Lucky Strike, such as Capelinhos (high temperature vent), and Grunnus (inactive?), as well as a low temperature vent field (on-axis), Ewan, have been described by (Escartín et al., 2015). Given the spatial relationship between the Main Lucky Strike hydrothermal field (MLSHF), and the intersection of northern rift faults with the southern rift faults, a structural analysis of this area can provide insight into the fault controls on fluid flow that leads to hydrothermal venting and sulfide precipitation. METHODOLOGY Structural data (dip direction and dip) was determined using Leapfrog Geo 4.0 software. Bathymetric data was obtained from Escartín et al., (2015) and references therein. The bathymetry was imported into Leapfrog Geo (in UTM format) and, using the structural modelling tool, individual measurements with dip direction and dip data were collected with a focus on the northern volcanic rift and the southern central volcano (Figure 2a). All measurements were taken from what the authors consider as normal faults, and to aid the determination of individual measurements a “face dip” map was constructed, where the bathymetry is colored by slope angle (Figure 2b). All measurements are simultaneously plotted on a stereonet generated by the Leapfrog Geo Software. Data were divided into northern and southern, and western and eastern zones to determine the relationship between hydrothermal venting and the structural geometries at Lucky Strike (Figure 2c). Slip measurements for individual faults were determined along the dip of the fault with a measuring tool. Net slip, heave (horizontal displacement), and throw (vertical displacement) was calculated for each of the zones.

Jan 1, 2018

By M. A. Vasina, I. A. Matveeva, E. A. Naumova, V. V. Doroshenko, N. A. Belov

"Using the calculated (Thermo-Calc software) and experimental methods (SEM, TEM, EMPA, DSC, XRD, etc.) the phase composition, structure and hardening of aluminium alloys of the Al-Ca-Zn-Mg system were studied in the following range: 2. 5%Mg, up to 10% Ca, and up to 14% Zn (wt%). Fragments of this quaternary phase diagram in the aluminium corner were constructed, including the liquidus surface, as well as some vertical sections. It was shown that the relatively large amount of zinc enters in the Ca-containing phase, which formula can be described as (Al,Zn)4Ca. An increase of Zn content leads to formation of Al4Ca primary crystals at lower concentrations of calcium. The eutectic (Al)+(Al,Zn)4Ca has a fine structure and aluminide particles are capable to spheroidization during the heat treatment at temperature 500 C. The maximal level of hardness observed on calcium containing alloys was higher than 200 HV, what gives the reason to expect good strength properties. With an example of an Al-9% Zn-2,5%Mg-3,5% Ca model experimental alloy based on the (Al)+(Al,Zn)4Ca eutectic, a principal possibility of manufacturing thin rolled sheets was demonstrated.INTRODUCTION Aluminum alloyed with calcium was first studied in 1970-80s by such authors as Piatti (1976), Moore (1978, 1980), Il'enko (1985), Swaminathan (1990), and Perez-Prado (1997) as superplastic materials. In particular, the alloy systems Al-Ca-Zn were studied (Il'enko, 1985, Swaminathan, 1990, Perez-Prado, 1997). For some time there was no new published works concerning the aluminum-calcium alloys. During the last years many works were published dedicated to the calcium alloying of magnesium alloys (Kim, 2011; Xu, 2011; Aljarrah, 2008; Bakhsheshi, 2014). This urged the authors (Belov, Naumova & Akopyan, 2016) to start studying cast and wrought aluminum-calcium alloys for construction (2008–2014). There is almost no information in the literature concerning triple and more complex diagrams of the aluminum-based system states with calcium and other elements. In recent work, parts of the state diagrams are plotted for the aluminum angle zone: Al-Ca-Mg-Sc (Belov, Naumova & Bazlova, 2016), Al-Ca-Ni-Sc (Belov, Naumova & Bazlova, 2017), Al-Ca-Si-Sc (Belov, Naumova & Akopyan, 2017) and others. Special attention was paid to the study of the system Al-Ca-Zn-Mg (Naumova, 2017). Based on this system creation of advanced extra-high tensile alloys is planned. Wrought extra-high tensile alloys series 7??? based on the system Al-Zn-Mg-Cu are well studied."

Jan 1, 2018

By Ram Song, Yohei Harada, Shinji Kumai, Kazuho Otsuka

"Recently, vertical-type high-speed twin-roll casting (HSTRC) has been developed. The HSTRC shows extremely high cooling rates over 1,000 K/s even at the mid-thickness area. The fabricated strip has many metallurgical characteristics; super-saturation of alloying elements, fine solidified structure, and homogeneous distribution of fine constituent particles. In Al-Mn based alloys, the Mn alloying element can be supersaturated in the a-Al matrix and also form Mn-containing constituent particles during solidification. The Mn supersaturation and the distribution of primary/secondary particles in cast products affect the metallurgical behavior in the down-stream processing and can improve mechanical properties of the final products. In this study, Al-Mn based alloy strips were fabricated by HSTRC with various Mn contents. The solidified microstructure, constituent particles and its distribution, and Mn solubility were investigated in the as-cast condition. Due to the high cooling rate of HSTRC, fine constituent particles were homogeneously distributed, and coarse intermetallics were not observed. Mn solid solubility was estimated by electrical conductivity. The estimated Mn solubility was equivalent between strip surface and mid-thickness area.INTRODUCTION Al-Mn based alloys, as non-heat treatable wrought aluminum alloys, are widely used in packaging and heat exchanger for automobile industry. Besides Mn, Al-Mn based alloys often contain Fe and/or Si as alloying elements or natural impurities. During solidification, Mn can be super-saturated in the Al matrix, and also form Mn-containing constituent particles. Additionally, in the subsequent thermal-mechanical processes such as homogenization, rolling, and intermediate annealing, Mn in solid solution precipitates out of the Al matrix as secondary particles. The size, distribution, type, and the amount of dispersoids including constituent particles affect to texture evolution, recrystallization behavior, and final mechanical properties of wrought Al-Mn based alloys (Huang et al., 2016; Huang & Marthinsen, 2015; Engler et al., 1995; Muggerud et al., 2013). Therefore, controlling the initial level of Mn super-saturation and the distribution of constituent particles are important in the cast Al-Mn based alloys."

Jan 1, 2018

By Tracy Brettmann, Will Bohlen

An innovative retaining wall design consisting of tangent drilled shafts with supplementary seal piles was used to limit continuing bank erosion along the Brazos River in Southeast Texas. The riverbank erosion had progressed to where it was threatening the stability of both the bridge abutment and corresponding approach embankment of the heavily travelled Highway 99 bridge at this location. A tangent pile design was selected because it was both much faster to install and more cost effective than a secant pile system. The design included both 5.5-ft and 10-ft diameter shafts with depths up to 130-ft and comprised both anchored and cantilevered sections. Supplementary seal shafts were also installed between the structural tangent drilled shafts to help plug any gaps between the tangent shafts. The plumbness and diameter of the shafts were tested using a sonic caliper to make sure the shafts were installed within the specified tolerance. The initial design had to be revised when a record flood from Hurricane Harvey impacted the site during construction. Introduction The Fort Bend Grand Parkway Toll Road Authority (Owner) needed to protect the north bridge abutment with a retaining wall system due to rapidly eroding conditions of the Brazos River banks within the 300- feet-right-of-way of the State Highway 99 Jodie Stavinoha Bridge. The extent of the local scour and erosion along the north bank of the Brazos River has caused concern for the structural integrity of the bridge. The magnitude of the erosion along the north bank at the location of the bridge has been measured at about 120 feet over three recent hydrologic flood events locally referred to as Memorial Day 2015, Memorial Day 2016, and Tax Day 2016. During construction, a new record flood level occurred due to Hurricane Harvey in August of 2017 that resulted in a portion of the retaining wall needing to be redesigned due to even more erosion occurring. The Brazos River is an actively eroding and meandering alluvial river plain that naturally meanders and migrates over time. The processes of bank erosion and meander migration were ongoing before the bridge was constructed and will continue in the future. These recurring major flood events, however, rapidly increased the rate of erosion in just a few years. Background. Due to the need to protect the bridge as soon as possible, the Owner selected a project team consisting of the designer, general contractor and specialty deep foundation contractor prior to final design to work together in developing a cost-effective design that could be implemented rapidly. The project team initially considered both a secant pile and tangent pile retaining wall system using drilled shafts. After reviewing various alternative designs, a tangent pile wall with seal piles was selected based on both cost effectiveness and speed of installation. The tangent pile with seal pile option was approximately 20 percent lower in cost and 50 percent faster to install.

Jan 1, 2018

By F. Andrieux

"Extruded aluminum profiles are increasingly used for lightweight vehicle construction. Since fracture strains of aluminum profiles are relatively low, damage modeling is crucial for reliable crash simulation. For aluminum profiles, not only the stress state but also the orientation influenced both the deformation and damage behavior. For the material characterization smooth tensile tests were performed in six orientations, both stress-strain curves and r-values were registered. Moreover notched tensile and shear-tension tests were performed in three directions. Finally punch specimens were tested to investigate biaxial loading. Digital image correlation (DIC) analyses were performed to determine local strain values such as critical values at failure. Numerical investigations were conducted with the strain based damage model GISSMO, which is well suited and widely applied for crash simulation. For a strain based failure model the choice of the deformation model is crucial. Deformation models with increasing complexity were investigated to find the best compromise over all experiments. It was found that there is still a great requirement on development of a material model which describes the orientation dependence of the hardening behavior over all stress states in order to be able to use a strain based failure model reliably.INTRODUCTION Weight reduction is an important step for less energy consumption and as a consequence aluminium is increasingly used in automotive parts. An important field of application is the well-established aluminium extrusion which allows the realisation of quite complex shapes of profiles required for an innovative lightweight design with integrated functions. Typical applications are chassis parts, bumpers, crash elements, air bags, etc. Especially the Al–Mg–Si medium strength alloys of the 6000 series can be easily extruded to form complex profiles and prevail for extrusion. Since fracture strains of aluminum profiles are relatively low, damage modeling is crucial for reliable crash simulation. For aluminum profiles not only the influence of the stress state but also the orientation with respect to the extrusion direction have an influence on both the deformation and damage behavior and need to be characterized. The effect of orientation on deformation behavior has been intensively investigated in the last decades and material models haves been proposed (e.g. Barlat & Lian, 1989; Barlat, Lege, & Brem, 1991; Barlat et al., 2003) to describe accurately anisotropic behavior. However it can be noticed that the parameters of anisotropic material models often rely on the yield stress in different directions, which means that the effect of strain hardening is not automatically accounted for. The accuracy of the models at large deformation is not guaranteed and has to be verified. In contrast to deformation models both the characterisation and the modeling of anisotropic damage behavior are not systematically studied. Isotropic failure models based on a critical strain as function of stress triaxiality (ratio of the hydrostatic stress to von Mises equivalent stress) are widely used for crash application (e.g., Bai & Wierzbicki, 2010; Sun, Andrieux & Feucht, 2009; Sun et al., 2013). The mechanisms of failure are manifold and not fully understood; to develop an anisotropic failure model it is mandatory to also have experimental data in different orientations for loading scenarios other than uniaxial tension, e. g. shear, biaxial tension, which implies an extensive experiment plan. This makes the development of failure models more challenging than deformation models for which it is possible to develop a reasonable anisotropic model using the framework of yield function and calibrate the material parameters based on results of tensile tests in different directions. Moreover the development of deformation and failure models are intricate as the variables governing the damage evolution are predicted by the def"

Jan 1, 2018

By Ashok Kumar, Rajendra Singh, Arun Kr. Singh

"A simple analysis of site conditions and capability of the mechanised depillaring (MD) operation found that this approach is suitable to address the strata control issues in coal pillar extraction under the weak and laminated roof strata of Pinoura mine. A continuous miner (CM) with a ram car and quad-bolter are used for single pass pillar extraction (first time in the country) to achieve a relatively faster rate of depillaring. A total of eleven panels are depillared under weak and laminated roof strata with a fair-rated rock mass rating (CMRI-RMR). It is observed that there is less influence of roof caving over the surrounding mining structures, especially those located out-bye the side of the extraction line. An attempt is made to quantify the goaf influence by field studies, which show that the maximum value of mining-induced vertical stress is 2.83 MPa, and the range of influence remains limited to around 15 m from the line of extraction. However, the problem of roof instability under the influenced zone was experienced due to the inherent nature of the weak roof strata. The chances of trapping of CM under weak and laminated roof strata of the panels is reduced by deriving a threshold value of the roof dilation, on the basis of a simple statistical analysis of the obtained field results. However, few incidences of roof collapses are observed over the CM due to the unpredictable behaviour of the geological structures below the freshly exposed strata, which also caused an obstruction in the speed of the extraction. This paper presents results of the field and laboratory studies, conducted for a successful application of the single-pass pillar extraction method, along with details of some CM trapping cases below the weak and laminated roof strata.INTRODUCTIONCoal is the major natural resource to meet the growing energy demand of India and this trend is likely to continue for the next 20 years in the country. A major part of the Indian coal belongs to Gondwana period, and only a small part belongs to Tertiary period. The estimated coal reserve in India per the exploration work done up to a maximum depth of 1200 m is 315.149 billion tonnes, including the proven coal reserve of 143.058 billion tonnes (CMPDIL, 2017). Even in presence of these huge resources of coal in India, there is a considerable gap between production and the users’ demand of coal. Most of the mines are operated by conventional semi-mechanised Bord and Pillar (B&P) methods; thus, the mining industry has gained a considerable amount of operational experience (Singh, Singh, and Dhar, 1996) and knowledge about strata behaviour (Singh and Singh, 1999; Singh et al., 2008) using this method. However, recently, the Indian coal mining industry has introduced some mechanised depillaring (MD) operations, where the level of production is relatively high. This approach of depillaring improves safety along with the production and productivity of a depillaring operation (Ram et al., 2017). The nature of the overlying strata of these depillaring operations vary greatly: from highly laminated, weak, and easily caveable to massive, strong, and difficult to cave."

Jan 1, 2018

By I. A. Agapov, I. S. Anisimov, N. V. Rylov, A. M. Sagitova

"The smelter slags represented silicate crystalline rock with medium to coarse-grained structure with spinifex skeletal network of olivine in hedenbergite matrix. Accessory magnetite, pyrrhotite and copper sulfides chalcopyrite, bornite, covellite, chalcocite and digenite occurred in dissemination in silicate matrix. The sample was studied by optical and electron microscopy with support of quantitative XRD. Modal mineralogical composition included olivine, pyroxene, magnetite, chalcopyrite, quartz, pyrrhotite. Copper deportment showed copper distributed in chalcopyrite (40 %), cuprite (22 %), covellite (21 %), bornite, chalcocite, digenite (5 %), Cu-bearing pyrrhotite (4 %) and spinel (2%). Liberation of copper minerals in the material ground to P80=71 µm was good with over 90 % sulfides in free grains and floatable binaries. The results showed theoretical possibility of 65 % copper recovery by flotation. Conclusion based on mineralogical data was precisely confirmed with flotation tests studies that proved to recover around 60 % of copper to commercial grade concentrate. INTRODUCTION Annual world copper matte smelter slags production is estimated to be millions of tones and contain thousands tones of unrecovered Cu, Zn and significant amounts of Ag and Au. Mineralogical study of one large processing sample of material of historical piles of Cu matte smelter slag was carried out to find possibility to recover copper and define theoretical recovery by flotation. The study of the slag material was aimed to determine possibility of upgrading the material on existing copper flotation plant to develop additional mineral resources. The objectives for mineralogical investigation were to target for best liberation fineness, determine theoretical recovery and possible concentrate quality for sulfide flotation tests. MATERIALS AND METHODS Large representative processing sample was collected by mixing of 120 t of slag material representatively excavated from historical piles of Cu matte smelter slag. The sample was used to define the processing technology to recover copper and gold from the material."

Jan 1, 2018

By Janne Kauppi, Kaj Jansson, Piia Suvio, Saara Hagnäs

"Historically the focus at the mineral processing sites has been to improve the production operations, while little focus has been set on how factors, such as the quality of water used in the process affects the metal recovery. Simultaneously increasing public pressure and water scarcity is driving the mining industry to recycle more water back to the process, which in turn leads to accumulation of impurities within the recycled water. This paper presents a concept for a systematic approach on targeting the impurities that have a negative effect on the metal recovery at the flotation circuit by using a novel solution called Process Water Recycling Plant (PWRP). These plants are designed with specific ore type in mind. PWRP produces cost-effectively process water to different target qualities, especially for flotation purposes enabling higher and more stable flotation recovery. It consists of pre-designed and standard water treatment units for a wide range of volumes. The application-specific configuration of units is governed by the water quality requirements, and can be designed according to specific customer needs. Testing has been carried out in order to investigate, which recycling water impurities affect the different ore types and how the metal recovery in flotation is affected as a consequence of the poor-quality water. The results indicate that every ore type is impacted differently and without a good understanding on how the water quality impacts the process performance, adverse effects on the flotation recovery can occur.INTRODUCTION With a focus on where water is used within the mineral processing, it has become evident that even though water is used in several different processes, majority of the water losses within the site occur at the tailings processing and the tailings storage facility. New tailings management technologies that can increase the recovery of water are actively being developed, but the key to improving the efficiency of water use and reducing the operational risks lies in closing the water loops and increasing the slurry density in the tailings processing. With this shift from conventional tailings technologies towards paste and dry stacking, water efficiency is vastly improved, but it might in turn lead to process water challenges with impurities, reagents and fines being recycled and accumulated within the production processes."

Jan 1, 2018

By C. K. Baxter, A. Odeshi, M. Mohammadi, E. D. Cyr

"Metal additive manufacturing has been a revolutionary step in designing new complex shapes with faster and cleaner building capacity in comparison to subtractive manufacturing processes. The ability to print lightweight alloys such as aluminum has made metal 3D printing attractive to different industrial sector from aerospace to energy and bioengineering. Of particular interest in this study, are the mechanical and microstructural properties of AlSi10Mg-200°C alloys. In this project, samples were 3D-printed in horizontal direction using an EOS M290 machine by Direct Metal Laser Sintering (DMLS) technique. Uniaxial tensile tests and high strain-rate impact e tests were carried out to investigate the mechanical properties and to study the repeatability of the process. A constitutive model is developed to predict the results of the mechanical tests at varying strain rates to better understand the high strain-rate behaviour of these alloys. Using optical microscopy, features such as scan tracks and melt pools within the AlSi10Mg-200°C samples were observed, and the microstructure was observed to be homogenous. The previously listed tests were compared to the results obtained for similar cast alloy counterpart, i.e. A360.0.INTRODUCTION A relatively new way of manufacturing parts is on the increase as rapid prototyping becomes increasingly popular throughout the world. Additive manufacturing is a process which, given a 3D model, uses metallic material in powder form to build a part layer by layer until completion (Gu, Meiners, Wissenbach, & Poprawe, 2013). This way of rapid prototyping is very attractive in comparison to other possibilities because of its ability to accommodate complex design and geometries. Conventional manufacturing methods have limitations when it comes to complex geometries, but additive manufacturing allows for increased design flexibilities while maintaining a light and stable final product (Murr et al., 2012). It also allows for a reasonable cost, especially for small batch sizes that would otherwise be extremely expensive."

Jan 1, 2018

By C. P. Lowes

"The REFLUX™ Classifier (RC™) consists of a fluidized bed housing, with a system of parallel inclined channels above. This system performs a simultaneous gravity separation and desliming of the feed material, utilising the inclined channels in order to retain the relatively fine dense particles. These particles promote the formation of an autogenous dense medium within the fluidized bed. Relatively large, low density particles are displaced from the fluidized bed and conveyed upwards through the inclined channels reporting to the overflow with other finer particles. Given the hydrodynamic role of both the particle size and density in determining the particle transport through a water based suspension, all gravity separators operate over a limited size range. In the case of the REFLUX™ Classifier, efficient separations can be produced across a very broad size range, from nearly 10 mm down to 10 m, however, for a given application the size range is much more limited. This study was concerned with the processing of dense minerals over a broad size range, and the need for multistage processing. Here the overflow from the first stage cascades to the second stage, incorporating coarse gangue rejection. This approach is shown to deliver remarkably high grades and recovery.INTRODUCTION The performance of the REFLUXTM Classifier (RC™) in beneficiating fine coal is well documented (Galvin, 2012). Although the technology can be applied to relatively fine particles below 0.1 mm, or coarser particles below 2.0 mm or even 8.0 mm (Galvin et al., 2010), in each case the technology is applicable to limited particle size ranges. In coal preparation, the most common size range is 0.25 to 2.0 mm, covering an eight-fold range in the particle diameter. Coal has a relatively low density, typically below 1600 kg/m3, with a significant portion below 1400 kg/m3. In water, the buoyant density difference (~ 400 kg/m3) is therefore low compared to that of gangue minerals (1600 kg/m3) by a factor of 4, enhancing the potential for separation. Thus, in coal preparation, the technology can be applied over a commensurately broader size range, typically up to eight-fold."

Jan 1, 2018

By Jan Kvinge, Aina Opsal Bakke, Yanjun Li, Jan-Ove Løland, Svein Jørgensen

"Compound casting is a very attractive approach to reduce the weight of components for some specific applications while keep both the functional and the mechanical property requirements. In this work, Al-7Si-Mg alloy /copper compound castings were produced through a low pressure die casting process. To reduce the oxide present in the interface, flux coating of the copper pipes was tested. The interface layer formed between the two alloys was investigated using Optical Microscopy (OM), Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS). Vickers Micro-hardness was also measured across the interface. Results showed that the flux coating prevented the formation of the metallic bond between copper and aluminum. Instead, high concentrations of potassium, magnesium and fluoride, coinciding with formation of KMgF3 and MgF2, were detected in the interface. In the castings without surface treatment, a continuous metallurgical bond was achieved. In the bond layer, various Al-Cu intermetallic phases have been detected. In addition, formation of primary silicon particles in the reaction layer was observed in all castings. The mechanism for the formation of the intermetallic phases and the strength of the interface layer have been discussed.INTRODUCTION Recent development in the automotive industry has focused on producing lightweight components, which can reduce CO2 emission and increase the efficiency. Often, one material alone is not able to meet the requirements for a specific use. The need for lightweight bimetallic components has therefore increased. Aluminum-copper bimetallic components can be used in wires and bus bars where conductivity is an important factor (Lee, Bang, & Jung, 2005). Compared to Al-Cu alloys, Al-Cu bimetallic components can reduce both weight and cost without reducing electrical and thermal conductivity (Sheng, Yang, Xi, Lai, & Ye, 2011). A challenge is, however, that aluminum and copper have high affinity to each other, especially at elevated temperatures. This causes formation of brittle intermetallic phases with high electric resistance (Liu, Wang, Sui, Wang, & Wenjiang, 2016). In addition, both metals are subjected to oxide formation on the surface. Copper is especially exposed to oxidation at elevated temperatures (Pinnel, Tompkins, & Heath, 1979), while a thermodynamically stable oxide layer will spontaneously form on the aluminum surface (Papis, Loeffler, & Uggowitzer, 2009). Oxides are known to be passive substrates, which will reduce wettability and will thus prevent the formation of metallic bonding between aluminum and copper (Papis, Hallstedt, Löffler, & Uggowitzer, 2008)."

Jan 1, 2018

By Leming Ou, Longsheng Yi, Qiming Feng, Yiping Lu, Qing Shi, Kun Liu, Guofan Zhang, Yanfei Chen

"Three important components of stirred tanks involved in energy consumption, the impellers and baffles, were investigated to intensify the agitation pretreatment on the flotation of nickel ores. Flotation tests revealed that the stirred tanks with two impellers had an advantage over those with one impeller in intensifying agitation pretreatment, and the higher agitation speed led to better flotation performance of nickel ores. Installation and removal of baffles were also employed in the stirred tanks, and flotation tests demonstrated that with baffles, the flotation grade increased significantly. These agitator design improvements were used to demonstrate that the energy supplied to the system significantly influences the flotation recovery and that if the energy consumption of the agitation pretreatment is ideal, flotation efficiency can be improved. Data from full-scale operations backed up these results.INTRODUCTIONThe flotation recovery of nickel-copper sulphide ore at the Western China nickel mine has historically been difficult due to the presence of large amounts of serpentine minerals (Feng, et al., 2012). Many studies reported that serpentine minerals tend to have a positive potential at pH values up to 9.5, while sulphides (such as pentlandite and chalcopyrite) have a low isoelectric point(Feng, et al., 2012). Serpentine minerals can form surface coatings on negatively charged sulphides surface due to electrostatic attraction when they interact with each other, which may also reduce collector adsorption and increase the hydrophilicity of the sulphide particles. In order to improve the flotation of nickel sulphides, sodium hexametaphosphate, sodium silicate, carboxymethyl cellulose (CMC), and other agents are used to disperse serpentine coating from sulphide surfaces in the flotation of the Jinchuan deposit and other nickel ores in China ( Kirjavainen and Heiskanen, 2007; Lu, et al., 2011). However, it is difficult to improve of the sulphide flotation due to the high dosage and the lack of selectivity."

Jan 1, 2018

By Audrey Boissier, Marie-Anne Camon, Cecile Cathalot, Yves Fouquet, Laurent Bignon, Arnaud Agranier, Ewan Pelleter, Sylvain Bermell, Florian Besson

INTRODUCTION In October 2014, on behalf of the French government, Ifremer, along with the International Seabed Authority (ISA), signed a contract to start a detailed exploration program for seafloor massive sulfide (SMS) deposits in the work plan located on the slow spreading Mid-Atlantic ridge (MAR). The contract has a fifteen-year lifetime and the related exploration program must include the outline of SMS deposits and a resource assessment, as well as detailed environmental base line studies in the contract area. The exploration for SMS deposits generally includes detection of hydrothermal plume anomalies, acquisition of surface and near-bottom geophysical data, sampling operations from the research vessel (e.g. dredges, cores), and dive operations. The environmental studies include, among others, short and long-term oceanographic measurements, water column studies, biodiversity evaluation close and far from SMS deposits, characterization of natural hydrothermal plumes and related sedimentation. The HERMINE research cruise held from March 13th to April 28th 2018 (R/V Pourquoi Pas?) was the first cruise dedicated to exploration of active and inactive SMS and to the quantification of natural chemical input to the water column. The HERMINE cruise strategy was built up around three main objectives: (i) regional exploration including the detection of plume anomalies and the research of SMS deposits, (ii) local exploration of a SMS district and (iii) integrated study of a natural hydrothermal plume. This 3-in-1 cruise required us to optimize the switch between dives and surface operations. Day-time was devoted to dive operations whereas night-time was mostly dedicated to CTD/Rosette operations. The Nautile HOV (Human Occupied Vehicle) was well suited to the working time schedule of the cruise because it was time efficient in shorter (i.e. < 10h) dives due to fast descent and ascent speed, fast submerged forward speed, high maneuverability and the ability to carry heavy science payload as well as large volume of samples. Regional Exploration The first seventeen days of the HERMINE cruise were devoted to regional exploration, i.e. the detection of new plume anomalies and the research of new sulfide mineralization in the French work plan (10 000 km2; 6 clusters).

Jan 1, 2018

By Zhu Yangge, Hu Xiaoxing, Feng Qiming, Zhang Guofan, Zhang Xingrong

"During the flotation process of ilmenite and titanaugite with fatty acid as collector, unavoidable ions such as Ca2+, Mg2+, Al3+, Fe3+ and Fe2+ demonstrate considerable influence on the floatability of the minerals. In this study, flotation test, zeta potential test, and solution chemistry calculation were adopted to investigate the mechanism of how these metal ions affect the floatability of ilmenite and titanaugite in different pH conditions. The results show that in weak acidic solution, Ca2+ and Mg2+ mainly freely exist in the solution with little adsorption on mineral surface, and their reaction ability with oleate ions is weaker than active site on ilmenite surface (Fe), thus they show negligible effect on the flotation of ilmenite; Al3+ shows similar reaction ability with oleate ion compared to Fe3+, which lead to competitive reaction with collector, so the flotation of ilmenite is depressed. While Fe3+ can adsorb on surface of titanaugite in the form of Fe(OH)3, and it shows stronger reaction ability with oleate ion compared with active site on titanaugite surface (Ca and Mg), which proves an activation effect on titanaugite flotation. In alkaline solution, all these five kinds of ions can adsorb on titanaugite surface, and the floatability of titanaugite will be activation. Based on the above analysis, it can be deduced that in the flotation system using fatty acid as collector, the adsorption of metal ions on mineral surfaces and the stronger reaction ability with collector than active site on mineral surfaces, are the two prerequisites for metal ions show activation effect on mineral flotation.INTRODUCTIONIn flotation pulp, the existence of metal ions is often inevitable. There are two sources for these metal ions: the first part is generated in grinding and flotation process due to the oxidation, reduction, corrosion or dissolution of minerals or grinding medium; the second part is from the flotation water or the addition because of the technology need. The metal ions in the pulp have a considerable influence on mineral flotation. Earlier researches are focus on the activation effect of mineral floatation by metal ions to obtain a higher flotation efficiency, many effective activators were found, such as Cu2+ activated sphalerite, Pb2+ activation wolframite, and Ca2+ activation quartz flotation, these metal ions have become the commonly used activators in industrial production. And many studies attempted to explain the mechanism of how metal ions affect the floatability of minerals. James (James et al, 1972) suggests that metal hydroxide precipitation is the main component leads to activation effect, while the study of Fuerstenau (Fuerstenau, 1976) showed that the metal ion hydroxyl complexes played significant role. In recent years, the reuse of mineral processing wastewater has attracted more attention (Rao et al, 1989; Liu et al, 2013; Wang et al, 2014), as a main component in flotation wastewater, the influence of “unavoidable ions” on flotation process still need in-depth study."

Jan 1, 2018

By Mathew Avery, Colby Barrett

In November 2016, a 7.8-magnitude earthquake caused more than 100,000 cubic meters of rock and debris to tumble down and bury the transportation infrastructure below Ohau Point in New Zealand. All routes between the northern and southern portions of South Island were severed. To undertake the rebuilding efforts, the New Zealand government established North Canterbury Transport Infrastructure Recovery (NCTIR) – an alliance to repair the road and rail networks between Picton and Christchurch. NCTIR’s aim was to have the road open by Christmas 2017, but work also continued into 2018 to complete a number of safety improvements along the highway. The presentation will review the initial remediation attempts, the necessity to re-evaluate the original efforts, the need to incorporate techniques that were “outside-the-box” and different from traditional methods, and the logistics and planning that were required to complete the work safely. INTRODUCTION Shortly after midnight on Monday 14th November, a magnitude 7.8 earthquake struck the small South Island settlement of Waiau in North Canterbury, 100km north of Christchurch. The quake was the largest in New Zealand since the magnitude 7.8 Dusky Sound earthquake in 2009 (GNS 2016). While shaking was widespread with over 15,000 recorded ‘felt reports,’ the worst shaking occurred about 50 seconds after the quake rupturing started. The energy of the tremor progressed north over several minutes with surface rupture recorded on a total of 21 faults. The length of all the fault ruptures combined was close to 100km (GNS 2016). The degree of ground shaking was high, recorded as Modified Mercalli Intensity Scale (MMI) Level 8 – Severe. This level of shaking causes considerable damage in ordinary buildings with partial collapse including fall of chimneys, factory stacks, columns, monuments, walls, etc. At a human level, people experience difficulty standing; while furniture and appliances shift. Geologically, the damage depends on the geological setting. In Kaikoura and the surrounding area, especially the coastal highway State Highway 1, north and south of the town, many of the slopes consist of over steepened weathered, fractured greywacke. During the quake, the shaking caused significant and widespread damage with a total of 26 major slips (and many smaller slips); closing both State Highway 1 and the Main North Rail Line between Picton and Christchurch.

Jan 1, 2018

By Greg Wyartt

In the Pilbara region of Western Australia, an iron ore mine is undertaking a high wall cut-back to improve stability and allow access to deeper ore deposits. Several sections of the wall have been classified geologically sensitive due to unstable localised geology, and therefore an engineered approach to vibration critical blasting was required. The use of electronic detonators allowed multiple signature (seed) holes to be incorporated into a production blast adjacent to the geologically sensitive area, therefore providing baseline vibration data to be used for future modelling with the added advantage of eliminating unnecessary pit closure downtime typically associated with a signature hole program. All subsequent blast patterns also incorporated multiple signature holes to provide additional data and allow continual updating – and therefore improved accuracy - of the blast prediction model.

Jan 1, 2018