Search Documents

By Wei Sun, Ruolin Wang, Jianjun Wang, Xiaodong Li, Honghu Tang, Yuehua Hu, Anh V. Nguyen, Haisheng Han, Kefeng Chen, Zhao Wei

It is difficult to separate scheelite especially from fluorite with fatty acid collectors because the adsorption mechanism of these collectors occurs through chemisorption of the oleate ion onto the mineral surface. A simplified flotation process using Pb-BHA complexes was developed to replace the energy-inefficient Petrov’s process of using a fatty acid, increasing the recovery of scheelite and reducing the cost. The relationship between surface chemical properties (crystal chemistry, solubility, and Zeta potential) of minerals and flotation by using a fatty acid or Pb-BHA complexes was studied in detail to provide new insights into the selective separation mechanism. The results indicate that the scheelite surface exposes more O atoms than Ca and that they are negatively charged due to the anisometric dissolution of Ca and WO4, which provides the possibility for separation using selective interfacial reaction. The FTIR and Zeta potential results indicate that both chemical and electrostatic adsorption play an important role in the adsorption of Pb-BHA complexes on the scheelite surface. The XPS results of the atomic composition and binding energies confirmed the presence of the adsorbed Pb-BHA complexes and that O and Ca may be the active adsorption sites. Therefore, scheelite was able to be collected by forming either a Ca-O-Pbcollector or W-O-Pb-collector (BHA). However, fluorite was only able to be collected by a fatty acid collector and colloidal [H2SiO3]n -, and a high temperature was needed improve the selective desorption of the adsorbed fatty acid collector by forming Ca-[H2SiO3]n - on the fluorite surface, resulting in serious problems in industry. However, the Pb-BHA complexes significantly contribute to improving the recovery of scheelite minerals, simplifying the flotation process, and circulation of the residual reagents and water. The new process has been applied in Shizhuyuan Mine, and improved the recovery by almost 10%.

Jan 1, 2018

By S. J. Schatzel, R. B. Krog, H. Dougherty

Longwall face ventilation is an important component of the overall coal mine ventilation system. Increased production rates due to higher-capacity mining equipment tend to also increase methane emission rates from the coal face, which must be diluted by the face ventilation. Increases in panel length, with some mines exceeding 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. To assess the effectiveness of current face ventilation practices at a study site, a face monitoring study with continuous monitoring of methane concentrations and automated recording of longwall shearer activity was combined with a tracer gas test on a longwall face. The study was conducted at a U.S. longwall mine operating in a thick, bituminous coal seam and using a U-type, bleederless ventilation system. Multiple gob gas ventholes were located near the longwall face. These boreholes had some unusual design concepts, including a system of manifolds to modify borehole vacuum and flow and completion depths close to the horizon of the mined coalbed that enabled direct communication with the mine atmosphere. The mine operator also had the capacity to inject nitrogen into the longwall gob, which occurred during the monitoring study. The results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Average face air velocities were 3.03 m/s (596 fpm) at shield 57 and 2.20 m/s (433 fpm) at shield 165. The time required for the sulfur hexafluoride (SF6 ) peak to occur at each monitoring location has been interpreted as being representative of the movement of the tracer slug. The rate of movement of the slug was much slower in reaching the first monitoring location at shield 57 compared with the other face locations. This lower rate of movement, compared with the main face ventilation, is thought to be the product of a flow path within and behind the shields that is moving in the general direction of the headgate to the tailgate. Barometric pressure variations were pronounced over the course of the study and varied on a diurnal basis.

Jan 1, 2018

By C. V. Deutsch, T. Acorn

Understanding and managing risk is of increasing concern for the mining industry. Although methods exist to model geologic uncertainty based on stochastic modeling techniques and multiple realizations, there are few approaches to manage this geologic uncertainty in pit optimization. Block values can be penalized if the block uncertainty is high, but the goal here is to consider the reserve risk within the pit. This paper presents an approach for pit optimization that considers all realizations simultaneously with a heuristic pit optimizer. The heuristic algorithm maximizes value and also penalizes reserve risk. The inclusion of multiple realizations provides access to the risk or uncertainty in the total pit value. Considering this information permits an active risk management approach that can manage the uncertainty in the reserves within the entire pit.

Jan 1, 2018

By L. O’Connor, E. Tarshizi

The objective of this work is to provide a detailed review and a list of references in chronological order, comprising 80 recent technical papers, on the use of discrete-event simulation (DES) modeling in mining engineering. In this article, the review papers of published mine simulation projects through 2007 are summarized, and then a comprehensive review of individual articles published from 2008 to 2015 is presented. This survey work also includes analyses of the simulation tools used in the published projects, mining types and applications in order to assess these key features and evaluate the recent state of research in mine DES simulation. In addition, an interactive map visualization for the locations of the simulated projects is made available on a website to benefit current and prospective scholars in the field. The results of this investigation revealed that the most common application of DES in mining had been mining equipment selection and analysis, while ore processing and risk management projects were less frequently reported. The results also showed that modeling surface mines were in the majority, but the trend of publications for underground mine simulations had also increased. According to the results, ARENA was the most popular simulation software package, but several simulation tools that were only used once or twice in the mining projects are also included in this review.

Jan 1, 2018

By T. Hollenberg, N. Nolten

The mining industry is one of the major energy consumers in Namibia. Energy costs increase the operating costs of Namibian mines, in particular, the processing plants, and result in an overall increase of production costs. A substantial part of the energy used is directly imported from South Africa. The cost of energy has been increasing rapidly in the past few years and will most likely continue to do so in the future. In 2015, the average wholesale price for energy from national power utility NamPower was US$87/MWh after rising more than 12 percent annually in the two previous years. At peak times, which are early in the morning and late in the evening, imported-energy prices are extremely high and have to be factored into the electricity tariffs. This problem is expected to intensify due to a projected 4 percent annual increase in energy demand. A major target of the Namibian mines, therefore, is to consider possible ways to address energy-saving challenges and to investigate possibilities for the mines to generate electricity internally during peak times. This is in alignment with the mines’ strategic plans and objectives to reduce total energy consumption and costs from both national and foreign electricity suppliers. In this paper, we explore addressing some of the key energy consumption and optimization challenges through process energy reuse and solar energy production to decrease demand for imported energy through a case study carried out in cooperation with Skorpion Zinc Mine and Refinery.

Jan 1, 2018

By Chee S. Theng

As the 2018 president of the Society for Mining, Metallurgy & Exploration Inc., I am pleased to present the 2018 issue of the Transactions of the Society for Mining, Metallurgy & Exploration Inc., Vol. 344. A significant portion of the contribution that we make as a professional society is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of the American Institute of Mining, Metallurgical and Petroleum Engineers (AIME). Those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2018 Transactions consists of a total of 59 technical papers, encompassing all 25 papers published in 2018 in the Technical Papers Section of Mining Engineering (Vol. 70) and all 26 papers published in 2018 in Minerals & Metallurgical Processing (Vol. 35). Additionally, this volume contains 8 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All of the technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our Publications staff. As the 2018 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume. The new year brings an exciting change. The publication of Transactions will cease with this volume. Instead, our Minerals & Metallurgical Processing journal has the new name of Mining, Metallurgy & Exploration (MME), and Transactions as well as the Technical Papers Section of Mining Engineering are incorporated into MME. The journal is published in partnership with Springer Nature, and all SME members have free electronic access to the journal.

Jan 1, 2018

By M. E. Buzon, M. E. Gunter

Talc has been the focus of recent civil litigation based on claims that asbestos minerals exist in talc deposits and therefore have caused asbestos-related diseases in those who have regularly used talc products. Such litigation, and ensuing confusion over the petrology and asbestos content of these deposits, challenges the talc mining industry in Montana and elsewhere in the world. The talc deposits in southwest Montana were formed by hydrothermal alteration of dolomitic marbles and are still actively mined. In general, talc formed by hydrothermal alteration of preexisting carbonate rocks is known to be nearly monomineralic and lacking in amphiboles. This paper includes data from analyses of representative ore samples from this mining region in southwest Montana. The results conclude that the presence of asbestos minerals — both amphiboles and chrysotile — is unlikely and that the ores are nearly monomineralic, as expected. Samples were characterized using a suite of analytical methods, namely, powder X-ray diffraction, X-ray fluorescence spectroscopy and electron microprobe analyses, which allowed us to determine the minerals present and the formation process. Our data and interpretations suggest that previous identification of asbestos minerals in these deposits is not accurate.

Jan 1, 2018

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage individuals within the mining companies to work together to identify such indicators, executing risk assessments comes with challenges. Specifically, varying or inaccurate perceptions of risk, in addition to trust and buy-in of a risk management system, contribute to inconsistent levels of participation in risk programs. This paper focuses on one trona mine’s experience in the development and implementation of a field-level risk assessment program to help its organization understand and manage risk to an acceptable level. Through a transformational process of ongoing leadership development, support and communication, Solvay Green River fostered a culture grounded in risk assessment, safety interactions and hazard correction. The application of consistent risk assessment tools was critical to create a participatory workforce that not only talks about safety but actively identifies factors that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s previous process of risk-assessment implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks, as well as a variety of mini case examples that showcase how the organization worked through these barriers to facilitate the identification of leading indicators to ultimately reduce incidents.

Jan 1, 2018

By B. A. Slaker, T. Miller, M. M. Murphy

An underground limestone mine in eastern Ohio was experiencing significant floor heave and roof falls, attributed to high horizontal stresses. Areas of the mine showing floor heave were monitored with roof-to-floor extensometers and photogrammetry surveys to determine the rate and magnitude of heave. Extensometer data were recorded hourly at four locations across adjacent entries while photogrammetry surveys of the floor were performed at the same locations every two to five weeks. A final survey was performed using an I-Site 8200 laser scanner. Following instrumentation, floor heave up to 10.1 cm (4 in.) was measured by the extensometers, photogrammetric reconstructions and laser scanner over a six-month period. The extensometers were biased by the location where they were placed, failing to consistently capture the location and extent of floor heave and cracking. The photogrammetry surveys were not precise enough to capture small magnitude movements. Mining in the area was halted and within several months the floor movement and incidence of roof falls were significantly lessened.

Jan 1, 2018

By K. C. Kocsis

Underground ventilation systems, which require electricity to operate the fans and fossil fuel for heating in winter, can account for a significant portion of the energy consumption of mines. Recent studies have shown that the ventilation system in deep and highly mechanized metal mines could be responsible for 40 to 60 percent of their overall energy consumption. Presently, underground ventilation systems are designed for peak air volume requirements, which usually occur well into a future stage of the mines’ operating life. As a result, during their early operating stages, the intake air volume of the mines could be well in excess of their true air volume needs. Such ventilation systems could be considered as uneconomic, and to remain competitive the ventilation design needs to improve while the mines are trying to reduce energy consumption and their carbon footprints. This paper introduces a new mine ventilation design method where an underground base-metal mine’s ventilation system is designed by integrating discrete-event mining process simulation (DES) with mine ventilation modeling techniques. Furthermore, based upon the output data generated by means of discrete-event mining process simulations, the air volume requirement for the operating life of the mine is determined for “traditional” versus “activity-based” ventilation requirements. The output data generated through ventilation simulations are then used to quantify the economic and environmental benefits of an activity-based ventilation delivery system.

Jan 1, 2018

By D. R. Willmer

An understanding of how health and safety management systems (HSMS) reduce worksite injuries, illnesses and fatalities may be gained in studying the behaviors of health and safety leaders. These leaders bear the accountability for identifying, understanding and managing the risks of a mining operation. More importantly, they have to transfer this knowledge of perception, recognition and response to risks in the mining environment to their workers. The leaders’ efforts to build and maintain a mining operation’s workforce that consistently executes safe work practices may be captured through more than just lagging indicators of health and safety performance. This exploratory study interviewed six leaders in occupations such as site-level safety supervisors, mine superintendents and/or general managers at surface and underground stone, sand and gravel and metal/nonmetal mine sites throughout the United States, with employee populations ranging from 40 to 175. In exploring leaders’ perspectives on how they systematically manage health and safety, examples such as approaches to task training, handling near-miss incidents, identifying future leaders and providing workers with feedback offer insights into how leaders translate their knowledge and management of site-level risks to others.

Jan 1, 2018

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The U.S. National Institute for Occupational Safety and Health (NIOSH)’s Pittsburgh Mining Research Division (PMRD) recently developed a series of models using computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side; 100 percent of the discharge redirected back toward the face, but divided equally to both sides; and 15 percent of the discharge redirected toward the face on the off-curtain side, with 85 percent directed toward the return curtain. These models are compared against a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated against experimental data, proving to accurately predict sulfur hexafluoride (SF6 ) gas levels at four gas monitoring locations. This study includes a predictive simulation examining a 45° scrubber angle compared with the 23° angle for the 100 percent redirected, equally divided case. This paper describes the validation of the CFD models based on experimental data of the gas distribution results.

Jan 1, 2018

By M. Hepokoski, M. Klein, D. S. Yantek, L. Yan

Research by the U.S. National Institute for Occupational Safety and Health (NIOSH) has shown that heat/humidity buildup is a major concern within coal mine refuge alternatives. High temperature and humidity levels inside a refuge alternative may expose occupants to heat stress. Due to the safety risks associated with testing using human subjects, NIOSH partnered with ThermoAnalytics Inc. to create detailed thermal simulation models of refuge alternatives with human occupants. The objective of this effort was to predict a miner’s core temperature response and moisture loss in environments that may be encountered in a coal mine refuge alternative. These parameters were studied across a range of temperatures and relative humidity values to determine if the current 35 °C (95 °F) apparent temperature limit for refuge alternatives is reasonable. The results indicate that the apparent temperature limit is protective, provided that miners are supplied with sufficient water. The results also indicate that the body core temperature does not reach dangerous levels even at an apparent temperature of 54 °C (130 °F). However, the results show that moisture loss increases with apparent temperature. Therefore, if the apparent temperature limit were raised, the water provided in a refuge alternative would have to be increased to offset moisture loss.

Jan 1, 2018

By C. J. Pritchard, R. D. Jacksha, K. V. Raj, C. B. Sunderman

In underground metal/nonmetal mines, repeated localized short-term exposure to high levels of airborne contaminants can become a serious health issue. Currently, there are no common mechanisms to control or mitigate these short-term high exposures to contaminants. To improve miners’ health and safety, the U.S. National Institute for Occupational Safety and Health’s Spokane Mining Research Division (SMRD) is developing a smart monitoring and control (SMAC) system for the real-time monitoring of mine air quality, with integrated countermeasures to reduce high concentrations of airborne contaminants in localized sections of mines. To develop and test a SMAC system capable of being implemented in an underground mine, SMRD researchers built a test apparatus incorporating a fan, louver, ducting and sensors combined with atmospheric monitoring and control software. This system will institute effective countermeasures to reduce contaminant levels, improving miner safety and health.

Jan 1, 2018

By M. E. Buzon, M. E. Gunter, B. D. McNamee

A Google search on talc asbestos yields more than 500,000 hits due to the growing number of civil lawsuits in this area. Historically, the litigation was centered on amphibole-containing industrial talc. There was no debate these talcs contained amphiboles, but the issue was the definition of asbestos and whether the amphiboles had an asbestiform habit. Ultramafic-hosted talcs, however, are formed in such a way as to not favor the formation of amphiboles in the talc, but they can occur in the surrounding black-wall. In these deposits, the serpentinite host rock is in direct contact with the talc, therefore, allegations can be made that non-asbestiform amphiboles or non-regulated serpentine group minerals can occur in the final products. We analyzed talcs from both metamorphosed carbonate- and ultramafic-hosted talc deposits using polarized light microscopy (PLM), scanning electron microscopy (SEM) with energy-dispersive spectroscopy (EDS), electron microprobe (EPMA) with wavelengthdispersive spectroscopy (WDS), transmission electron microscopy (TEM) with EDS, and powder X-ray diffraction (XRD). Compositions of minerals determined by EDS alone are not sufficient to confidently identify asbestos, despite common practices by some researchers. We emphasize, using both historical samples, and analyses of currently contested minerals, the importance of determining both the structure and composition of a mineral, as well as defining its morphology, before concluding whether it is asbestos.

Jan 1, 2018

By T. R. Kostecki, A. J. S. Spearing, G. S. Esterhuizen, K. V. Jessu

Discontinuities are geologic occurrences in rock and when present within a pillar, reduce the strength of the pillar. Empirical formulas that are commonly used to determine pillar strength do not explicitly take into account the presence of discontinuities and thus can overestimate the pillar strength. The effect of discontinuities on the strength of pillars has been investigated using numerical models, but in these models, the discontinuity strike was parallel with the pillar faces. In this study, fully three-dimensional hard rock pillars were simulated using numerical modeling to understand the effect of the discontinuity dip direction on square and rectangular hard rock pillars. Based on the results, recommendations to assess a pillar’s strength in the presence of a discontinuity are discussed.

Jan 1, 2018

By J. F. Burr, D. Snyder, W. Calder

This paper provides a determination of the equivalent level of protection of the international standards relative to similar criteria used by the U.S. Mine Safety and Health Administration (MSHA) to approve two-fault intrinsically safe (IS) stand-alone equipment. U.S. mining law requires such a determination for MSHA to use alternatives to existing standards. The primary issue is to demonstrate that the international standards for equipment evaluation will provide at least the same level of protection for miners as the document currently used by MSHA.

Jan 1, 2018

By T. J. Lutz, D. S. Yantek, L. Yan, J. R. Srednicki, J. A. Yonkey, G. T. Homce

Federal regulations require the installation of refuge alternatives in underground coal mines. Of the inuse refuge alternatives, more than 95 percent are mobile refuge alternatives, with the remainder being built-in-place (BIP) refuge alternatives. Heat/humidity buildup has been one of the major concerns with mobile refuge alternatives. For BIP refuge alternatives, however, there is a lack of in-mine heat/humidity test data to determine the extent of heat and humidity buildup. To quantify heat/humidity buildup in BIP refuge alternatives, the U.S. National Institute for Occupational Safety and Health (NIOSH) performed a series of heat/humidity tests on a 60-person BIP refuge alternative with and without a borehole air supply. At various times during the year, tests were performed with cooled, heated or unconditioned borehole air to examine how various outdoor temperatures may affect the thermal conditions inside a BIP refuge alternative. The results show that the air supplied to a BIP refuge alternative may require heating or cooling, depending on the outside air temperatures and the temperature of the mine. For example, during tests with an external ambient temperature above 21 °C (70 °F) and a relative humidity of 90 percent, providing 13 °C (55 °F) dew point air at 775 scfm, which is slightly higher than the mandated flow rate of 12.5 scfm per person, kept the internal apparent temperature below the mandated 35 °C (95 °F). Results for each test case are presented.

Jan 1, 2018

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck, Y. Zheng

Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27 percent of respirable coal mine dust can be attributed to longwall shield movement, and developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine the ability of the foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used: compressed air and blower air. Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For compressed air foam in 3.3 m/s (650 fpm) ventilation, 98 percent of agent A was intact while 95 percent of agent B was intact on the roof at three minutes after application. At 30 minutes after application, 94 percent of agent A was intact while only 20 percent of agent B remained. For blower air in 3.3 m/s (650 fpm) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 min after application, 74 to 92 percent of foam agent A remained, while 3 to 50 percent of foam agent B remained. Compressed air foam seems to remain intact for longer durations and is easier to apply than blower air foam. However, more water drained from the foam when using compressed air foam, which demonstrates that blower air foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able to withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control.

Jan 1, 2018

By Francisco Contreras

El sistema electrohidráulico es una alternativa económica para reemplazar sistemas neumáticos y operar una instalación nueva en el accionamiento de las compuertas de carguío; con un costo mínimo en el consumo de energía eléctrica, si está constituido por los componentes debidamente dimensionados. En el presente trabajo se detallan tales componentes, así como el procedimiento de aplicación de la mecánica de fluidos en ingeniería (principio de Pascal); lo que permite transmitir grandes fuerzas utilizando pequeños elementos constitutivos, y realizar maniobras de mando y reglaje con facilidad. Dado que una bomba hidráulica movida por un motor eléctrico es capaz de desarrollar esfuerzos enormes aprovechando la sección de cilindros, esta tecnología tiene un amplio potencial de desarrollo. Con un solo equipo de poder se pueden operar independientemente las tolvas que sea necesario maniobrar en distancias de hasta 500 metros con telegobierno por mando eléctrico. Puede aplicarse en piques, rampas, galerías, cruceros, etc.

Dec 31, 2017