Search Documents

By W. R. K. Wu

This Bureau of Mines report presents a statistical study of the repeat abilities of coal-plasticity parameters obtained in the tests with the Gieseler plastometer and the Audibert-Arnu and Hoffmann dilatometers. Repeatability is expressed in terms of one or two standard deviations for the differences between duplicates. The statistical method employed here is summarized. Results are tabulated for the temperature and nontemperature parameters of the three tests.

Jan 1, 1970

By Lars Osen

The Bureau of Mines investigated (1) the effect of torsion on yield and ultimate strengths of bolts when the torsion is applied first and tensile load is applied independently of torsion and (2) various methods of increasing the tension-torque ratio and/or narrowing the data spread of the tension-torque relationship. A special torsional attachment was fabricated to attach to a universal testing machine to independently subject rock bolts to combined tensile and torsional loads. It was found that initially installed torsion is nullified during tensile loading and the tensile yield and ultimate strengths are not significantly reduced. Lubricating various components of a bolt assembly or using hardened washers will improve the tension-torque relationship during conventional installation; however, the torsional load is not nullified during this type of loading. Hence, a bolt is subjected to a combined stress throughout the loading cycle; the yield point will thus be lowered compared with the pure tensile yield if care is not taken during installation to stay below the torsional yield.

Jan 1, 1966

As the high-grade copper deposits in the world become depleted, there is an increasing focus on developing lower-grade ores which contain problematic impurities such as arsenic. Indeed, many high-arsenic ore bodies remain undeveloped because of their high arsenic levels. Separation of arsenic from copper at the beneficiation stage is difficult using the current processing techniques and invariably copper concentrates produced from these ores contain high arsenic levels, sometimes so high as to make them unacceptable to copper smelters. New, sustainable approaches are needed to allow development of high-arsenic copper ores while at the same time minimizing arsenic dispersion into the biosphere. The most promising route for separating arsenic from copper at the flotation stage centers on the use of pulp potential control. In recent years CSIRO has demonstrated at laboratory scale, for a number of high-arsenic copper ores, that crude flotation separation between arsenic-bearing minerals and copper-bearing minerals can be made. The differences in specific minerals responses to changes in pulp potential and pulp pH are exploited for this separation. Such separations nominally produce a low-arsenic high-copper concentrate and a low-copper high-arsenic concentrate. The former can be smelted without penalty, while the latter requires further treatment to capture and stabilize the arsenic and to recover the residual copper. Consideration has now been given to treatment options for the high-arsenic low-copper product. A pyrometallurgical option, involving a low temperature roast to selectively fume off the arsenic and leave a high-copper calcine, coupled with an arsenic stabilization step, has been demonstrated in the laboratory, and a preliminary techno-economic evaluation shows the process to be economically favorable. These results were recently published. CSIRO has now investigated an alternate hydrometallurgical option, involving atmospheric alkaline sulphide leaching of the high-arsenic product, where the arsenic is selectively dissolved leaving a copper-rich leach residue. The leaching testwork was carried at on the same high-arsenic low-copper material used in the roasting studies, enabling a techno-economic comparison of the alternate roasting and leaching treatment options to be made. The alkaline leaching work is briefly described and the results of the process option comparison presented and discussed. Keywords: arsenic, copper, economics, enargite, ore flotation, tennantite INTRODUCTION

Sep 1, 2012

By Alfred W. G. Wilson

In this paper is presented a review of the changes that have taken place in certain Canadian non-metallic mineral industries since 1909. The fifteen-year period 1909 to 1923, inclusive, has been selected for two reasons. In the first place, statistical treatment of the subject under review has been nearly uniform throughout the period. In the second place, this decade and a half is itself further subdivisible into three well marked quinquennial periods, the middle one covering the period of the great war when industrial conditions were greatly disturbed. It then becomes possible to institute certain comparisons between equal periods before and after the war disturbances. The items selected for inclusion in this review are certain of the more important members of that class of minerals usually grouped together under the heading of non-metallics. They are all minerals of which Canada is known to possess important resources, and which are indispensable to many of our greatest manufacturing industries.

Jan 1, 1925

By Karl Marquis

La Mine Mouska exploite depuis deux ans certains blocs de réserve à l?aide de la méthode long trou. Même si, à priori, la méthode long trou semble rentable, le contrôle de la dilution ainsi que le respect d?un échéancier serré s?avèrent primordiaux afin que cette méthode d?exploitation puisse être justifiable économiquement. La présentation suivante fera la comparaison économique entre cette méthode et celle de chambre-magasin.

Oct 1, 2001

By A. W. Fahrenwald

"The rate of progress in the last three years in the development of differential flotation has been rapid beyond the realization of most people. Differential flotation is no longer a ""delicate"" and unreliable process, but is now in wide use. Its ""safety"" is due to the wide use of chemicals which either depress or enhance floatability by definite modification of surfaces.The extent of the development and reliability of differential flotation methods any be emphasized by pointing out that there are now several customall-flotation"" plants in this country treating complex lead-zinc-iron ores from widely separated mines. While these ores differ in chemical composition and apparently in physical nature, the various ores treated in such a plant are passed through the same crushing and grinding equipment and through the same flotation machines and flow sheet with only slight changes, if any, in quantity and kind of chemicals and oils added.Some of the development in differential flotation is due to intelligent research on the part of well-trained chemists and metallurgists; much of It must be attributed to empirical testing.Much of the success in differential flotation is due to more care being given to constant conditions with regard to such factors as (1) fineness of grinding, (2) density of pulp entering flotation machines, (3) quantity and constancy of oils and chemicals added to the pulp, and (4) place of addition of reagents, and time of ""conditioning"" treatment of pulp with reagents."

Aug 1, 1925

By Grant S. Diamond

THE BIBLIOGRAPHY on the use of static electricity in mineral beneficiation consists largely of patents. Some references are found in mineral textbooks, but very little data on flow-sheets of commercial installations are known to the writer. As a matter of fact there have been relatively few successful commercial applications of importance. Johnson prepared and published a Table showing the polarity and static field intensity requirements of many minerals. There have been reports of successful beneficiation of rutile, zir-con, coal, potassium chloride, and phosphate rock. Otherwise, the field of success has been very limited. This may be due to three reasons: first, the mining industry has been averse to dry processes, be-cause of dust nuisances in dry crushing; second, the electrostatic processes used in the past apparently developed no substantial economic advantages; and third, because flotation or other . methods have proven successful on many minerals, the industry has not felt the need for a radically different process. In the feldspar industry there was ?an attempt at electrostatic beneficiation about twenty years ago which was based on the use of fluoride fuming of the pegmatite head feed, in order to make the mineral reactive in a static field. This process was originally said to be successful, but was discontinued because of corrosion damage to machinery. Another effort by use of a chemical additive such as an or-ganic hydroxyl compound has also been attempted. Neither of these processes is known to be in use today.

Jan 1, 1957

By Paul Swatkowski

A Note About Copyrighted Material ??Permission to Use? has been granted ?Teachthe7habits ?Think win/win (4thHabit) ?Don?t stop here ?i.e., buy the book

Jan 1, 2009

By A. M. Bryukhanov, A. G. Mnukhin

The report states accident rates for gassy/dusty coal mines represented as an ergatic system "man – machine - environment" with further analysis by the method of conditional probabilities. A coal mine has been analyzed with allowance for the attending personnel, equipment and environment as a sequence of events and states. Probabilities of operational states have been determined and prediction of mine behavior has been made on the basis of investigation findings for equipment and the personnel states, and analysis of the environment (i.e. mine and mining conditions). Utilization of expert estimation methods has been considered for determining major operational parameters of gassy/dusty mines. The importance of standardized values of permissible occupational risks (permissible probability of accident, PA) is demonstrated. It is also stated that a procedure is essential to determine these values, involving regular check-ups of the integral safety criterion at all mines and further development of customized recommendations for individual mines on efficient improvement of accident situations. Methodology to determine the assessment criteria has been developed and scientifically substantiated for permissible accident rates in hazardous industries.

Jan 1, 2003

By L. Lui, A. Cauchon, A. R. Laplante

"The gravity circuit at Les Mines Camchib Inc. consists of two pinched sluices to bleed a feed to one of two 76 cm (30"") Knelson concentrator. The Knelson concentrate is upgraded to smeltable grade with a smaller Knelson (18/30 cm) and a riffleless table. Their tails are column cyanided and washed prior to recycle to the grinding circuit. This paper details size-by-size circuit performance. The Knelsons recover around 90% of free gold (as determined by Mozley Laboratory Separator), even below 37 µm. The sluices are ineffective, with upgrading ratios around 2, but approaching unity in the fine sizes. Much of the effectiveness of the circuit lies in the high gold circulating loads in the grinding circuit, which partly atone for the poor sluice performance, and the ability of the Knelsons to recover free gold. Secondary upgrading recovers slightly above 99% of the primary concentrate gold, 90% of it in a 65% Au concentrate and the balance in a heavily loaded (10 to 20 oz/st) pregnant solution. INTRODUCTIONBackgroundThe operating performance of the mill of Les Mines Camchib Inc. has been described earlier (Laplante et al., 1989). The presence of significant chalcopyrite (1 % and up) makes flotation necessary prior to cyanidation, to limit cyanide consumption and minimize environmental impact. In 1982, the presence of very high gold circulating loads in the grinding circuit lead to the commissioning of a gravity circuit, schematically shown in Figure 1. Gravity recovery of gold has been found beneficial because it increases metallurgical recovery by 1-3% (Laplante et al, 1987), as only part of the flotation tail is cyanided, and economic recovery, because of the lower net smelter return of gold in the flotation concentrate (as compared with the gravity concentrate). The latter increase is estimated, with a net smelter return of 95%, at 1.5% when gold recovery by gravity is equal to 30%. In early 1988, a sampling program was initiated to characterize the behaviour of gold in the grinding/gravity circuit. This paper reports on the results of this study."

Jan 1, 1990

By J. N. Van der Merwe

Due to the approaching depletion of reserves in the Witbank Coalfield, and the fact that the Waterberg Coalfield is as yet under developed, there is increasing pressure to extend the lives of the operating coal mines in the Witbank Coalfield. One potential source of coal is the old pillars, often small and at shallow depth, that were not left with secondary extraction in mind. At face value, some of these pillars appear to be suitable for secondary mining due to their high safety factors. However, it is known that over time, these pillars have scaled and the current sizes are smaller than the as-mined dimensions. It is also known that at shallow depth, the overburden is often less likely to fail during secondary mining, resulting in high abutment loads on the unmined pillars. The paper proposes a systematic method to pre-evaluate those old pillars for the possibility of stooping. The method consists of elements of fundamental methods and newly developed technology. In essence, it revolves around using empirical methods to estimate current pillar dimensions, followed by numerical modelling to investigate the probability of progressive pillar failure and then fundamental methods to determine the limits of applicability of the numerical model.

Jan 1, 2012

By Gustavo Quiquia Mucha

El presente texto describe las experiencias realizadas por la Compañía Minera Milpo SAA en el marco de una gestión social basada en la consulta previa, libre e informada en la Exploración Minera Responsable. En ese sentido, es importante la cooperación entre la empresa minera y la comunidad, así como la incorporación del marco ideológico empresarial y metodológico, basado en los principios del Convenio 169 de la OIT sobre Pueblos Indígenas y Tribales en Países Independientes, las estrategias y las líneas de intervención social de la Compañía Minera Milpo SAA en los proyectos de exploración minera responsable.

Sep 12, 2011

By P. A. Plunkert, D. E. Morse, Pui-Kwan Tse, W. D. Menzie, Lucy McCartan, J. F. Papp

China’s burgeoning economy is responsible for a major share of recent world mineral consumption increases. In addition to factors traditionally recognized in market economies1 and factors unique to specific commodities, Chinese consumption now plays a major and increasingly important role in energy and mineral markets for many commodities, such as aluminum, copper, iron and steel, and oil. China has the world’s second largest economy after the United States. And its long-term importance to the minerals markets is even greater than indicated by its gross domestic product (GDP), which is currently less than two-thirds of that of the United States (Table 1). This is because China’s rising standard of living is accompanied by rapid industrialization and urbanization. Its consumption of mineral materials for infrastructure development for its very large population is significantly greater per capita than that of such developed economies as the United States, the European Union and Japan. In other words, China’s per capita production is rising at a rapid rate and will probably continue to do so for many years.

Jan 1, 2006

By A. Bhattacherjee

Industries in general and the mining industry in particular have become more safe than ever before. However, there is a need to increase the search for the causes of mining work-related injuries and to contribute to their reduction through job design, work procedures, and worker training. Mine accident and hazard control has to be practiced in a manner which is consistent with the overall objectives of the mine management, among which are the optimum allocation and effective utilization of the resources. The purposes of this paper are to (i) review the role risk analysis in safety management with references from mining and other industries; (ii) discuss the risk measures appropriate for injury analysis; (iii) present a set of analytical tools to injury experience data in under-ground coal mines; (i v) apply these tools on case study example; (v) discuss the results of the case study; and (vi) amplify the application limitations and the future research needs.

Jan 1, 1991

By R. W. Stahl

Methane, a highly explosive gas evolved during the coal-formation process, is one of the hazards of mining most difficult to overcome. It is retained between particles of coal and entrapped in strata overlying and underlying the coal beds to a degree dependent upon the permeability of the enclosing strata. Considering that methane might be encountered at any time during the mining of coal, attempts have been made through the years to minimize the sources of ignition at coal-mine faces, such as the introduction of permissible electric equipment, the prohibition of smoking and open lights, and the development of safer explosives. The sparks created when mining-machine picks contact sandstone or iron pyrites2/ constitute one source of ignition, always recognized as a possibility but never greatly emphasized in the United States until recently, when ignitions began occurring with rather alarming frequency and in widely scattered coal-producing areas.

Jan 1, 1956

By H. Kenworthy

The objective of this investigation was to evaluate the technical feasibility of smelting certain low-grade domestic iron ores in an electric furnace. Laboratory-scale experiments showed that a high recovery of iron in the form of pig iron can be obtained from east Texas ores containing less than 25 percent iron. The pig iron was amenable to standard-or electric-furnace-refining methods for producing steel. Car-bon, silicon, and phosphorus were the primary impurities removed in refining. Overall recoveries of iron as pig iron exceeded 95 percent, in contrast with commercial mineral-dressing recoveries on these particular ores of 50 percent of the iron as a 45-to 50-percent iron concentrate.

Jan 1, 1958

By P B. Hills, R J. Walton

Geotechnical instrumentation has been implemented as a key step for monitoring and optimising an engineered mine design for managing seismicity at the Beaconsfield Gold Mine. Measurements of displacement, stress change, ground control element load and seismic response of the rock mass allow for back analysis and calibration of critical parameters for feedback into the engineering design loop. Instrument clusters are installed in strategic locations prior to the commencement of stoping in order to determine the nature of the response of the rock mass to stoping. A selection of instruments including instrumented cable bolts and rod extensometers, resistance wire extensometers, hollow inclusion stress cells, vibrating wire stress meters and resistance wire extensometers are used to gather data through a data logging system. The rate at which data is recorded is adjusted to provide more information during periods of anticipated rapid change such as around stope firings or during periods of high seismic activity, and less information during periods of anticipated quiescence. The twofold purpose of the instrumentation is to calibrate the numerical modelling output which forms the basis of the engineered mine design, and to provide an alert mechanism where the behaviour of the rock mass is not what was anticipated, or where the impact of that behaviour may compromise the integrity of the engineered ground control system. The paper describes the location of instrument clusters with respect to stoping, the type of instruments employed and the method of data acquisition. It provides examples of results obtained and illustrates the way in which that information is used to optimise the mine design and manage seismicity.

Jan 1, 2008

By T. Bhambhani, E. Arinaitwe

Solvay has developed several novel reagent innovations to improve separations in sulfide ore flotation and address major industry challenges. These innovations include: a) carbon management strategies to reduce the deleterious impact of organic carbon on flotation circuits; b) new collectors for heavily tarnished or oxidized Cu-Au ores; and c) a functionalized depressant for minimizing penalty elements in metal concentrates. Owing to their unique chemistries, these innovations exhibit a wide spectrum of rather unique properties that are quite in contrast to the traditionally used reagents. The chemistry, attributes, application, and advantages of these innovations are discussed in this paper based on laboratory, pilot, and plant results and observations for various ores

Jan 1, 2023

By 1980, the U.S. mining community had reached a broad consensus regarding coal pillar design. The pillar load could be estimated from tributary area theory, and the pillar strength from empirical formulas and laboratory coal strength testing. Then the growth of longwall mining required new thinking. Recently, powerful design methods have emerged from analysis of large data bases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. Sophisticated numerical models have also helped transform the pillar design landscape. In the process, our understanding of pillar mechanics has been greatly enriched. A new paradigm divides pillar failure into three categories:

Jan 1, 1999

The mineral chromate is the sole current source of commercial chromium Chromite varies compositionally within limits permitted by the formula ((Mg,Fe,Zn,Mn)(A1,Cr)2O4) No chromate has been mined in the United States since 1961 In the past, almost all the chromate mined in the United States came from Alaska, California, Maryland, Montana, Oregon, and Pennsylvania, with about one-half of all production coming from Montana Primary chromate deposits occur only in certain kinds of ultramafic or closely related anorthositic rocks The two major types are stratiform (layered) and pod-shaped The Stillwater Complex of Montana is the largest known United States resource It is a stratiform deposit where several exposed zones of high-iron chromiferous material extend in length Since there is no commercial chromate mining in the United States, there are no environmental problems related to underground mining

Jan 1, 1975