Search Documents

By A Sainoki, D Fukuda, K Shioya, C Zhang, M Sharifzadeh, T Yamaguchi, S Saydam, J Kodama, C A. Amagu, Y Fuji

In an open pit mining, ensuring stability of rock slope has been one of the major challenges. As the instability of rock slopes can results in slope failures; consequently, endanger the lives of workers, affect mining operations, and often lead to economic losses. Therefore, it is practical important to study the stability of rock slopes to ensure safe, smooth, and effective mining. The stability of rock slope of about 130 m height at Higashi-shikagoe limestone quarry, which has experienced slope failures four times since 1996, was assessed. The rock mass at the quarry is consists of mainly limestone, schalstein and slate rocks intersected by clay seams of about 70 m thick at footwall of the rock slope. Previously, the effects of limestone excavation at the foot of the rock slope and shear failure due to rainfall infiltration have been investigated. Although clay is widely known to plays a vital role in the stability of slopes in engineering projects including mines, but its impacts on slope deformation at the study quarry are not adequately examined. Therefore, the present study addressed the impact of presence of clay on slope deformation at Higashi-shikagoe limestone quarry by employing both field displacement measurements and numerical simulation. Firstly, surface displacements measured by automated polar system (APS) for over eight years were analysed to understand the overall characteristics of the slope deformation. The measured results show that the displacement gradually decreases with time. The maximum displacement of about 100 mm was observed at middle of the rock slope. Secondly, the effect of deterioration and plastic behaviour of the thick clay layer were simulated using two-dimensional finite element method (2D FEM). The simulated results reveal that the clay exhibited deterioration by water contact and plastic behaviour arising from mining activities at the footwall of the clay zone. Based on the characteristics of the measured and simulated results, it was found that the displacement induced by the effect of deterioration of clay is more noticeable at the north side of the quarry whereas displacement induced by excavation is quite significant at the south side of the quarry if clay behaves as an elasto-plastic material.

Nov 29, 2022

By Prasenjit Basu

Drilled displacement piles are being increasingly used as foundation elements, particularly in projects requiring fast construction. Different types of drilled displacement (DD) piles are available in practice. DD piles are classified according to the drilling tool design and installation method. The capacity of a DD pile, depending on its type, is between the capacities of geometrically similar nondisplacement and full-displacement piles installed in the same soil profile. This paper provides an overview of the different types of DD piles and their installation techniques and describes three design methods used in practice. It also compares DD pile capacities obtained with these design methods for two different sites.

Jan 1, 2010

By C J. Adams, H J. Campbell, A J. Tulloch, I J. Graham

New Zealand can be regarded as a rifted part of mineral-prospective eastern Australia. Geologically credible comparisons between selected trans-Tasman and SW Pacific geological provinces and units, especially those that contain significant mineralisation in Australia, can help provide a useful exploration framework for New Zealand. As part of a six-year Mineral Wealth of NZ and its EEZ (MWE) research programme, we have targeted selected geological units in eastern Australia for comparison and contrast with their potential New Zealand counterparts. In future years, the programme will focus on geological units in New Caledonia.

Jan 1, 2005

By W. M. Snoddy

The Montana Tunnels diatreme is a low-grade polymetallic ore body containing economically mineable quantities of gold, silver, lead, and zinc. Widely varying gold grades combined with the general erratic nature of the mineralization create a complex sampling, assaying, and ore control problem. In order to maximize productivity and profitability, a variety of procedures have been used. These include differing sample size, frequency and method. In addition, assay techniques have been adjusted and refined to fit specific requirements, the result of which is an accurate, functional sampling and ore control system.

Jan 1, 1991

By F. W. Horton

This paper covers the salient features of the occurrence and mining of sheet mica in the United States and the preparation of mica for market; presents the results of a study of the physical properties of domestic and foreign micas, which the author hopes may he of interest to every mica user, as it definitely answers many questions as to the suitability of various minas for particular purposes; and discusses mica-trade conditions and the future outlook for the domestic mica industry. ACKNOWLEDGMENTS The author takes pleasure in acknowledging his indebtedness to J. R. Thoenen, of the United Stator Bureau of Mines, under whose guidance the work reported herein was performed, and to Frank L. Hess, also of the Bureau, for information on the geological and mineralogical characteristics of mica-bearing pegmatites.

Jan 1, 1935

By A. Noble

"In coal and mineral processing, several numeric parameters are used to quantify the separation performance of unit operations. For density-based separations, the partition curve is used as the starting point for many stages of diagnostic analyses. The curve is often quantified by its midpoint slope sharpness, and this single value is subsequently used for technical evaluation, benchmarking, and comparison. While this analytical approach does depict misplacement by relative density class, it inherently prioritizes middling separation and does not consider process economics or the micro-price value of individual classes. An alternative parameter, the organic efficiency, does indirectly consider process economics, but it does not reveal information on the root cause of lost revenue or misplacement. In this paper, a new analytical approach, the partition moment of inertia, is introduced. This parameter reconciles the technical misplacement data derived from the partition curve with the economic data derived from micro-pricing. The result is a new analytical procedure that promises better use of performance data. IntroductionPartition curves are commonly used in the characterization, evaluation and simulation of various physical separators. In mineral processing, partition curve analysis is routinely applied to hydrocyclones, screens, density separators and other beneficiation technologies that are based on intensive physical properties. Graphically, the partition curve depicts the recovery of particles as a function of the physical property on which the separation is based, such as particle density, size or magnetic susceptibility. Given the probabilistic nature of many real separators, the partition curve often exhibits a characteristic S shape (Fig. 1), similar to a cumulative normal distribution. Other geometric features of the curve are also depicted in Fig. 1, including the high and low closeout, or bypass, values; the midpoint slope; and the separation cut point, defined as the property value with 50 percent recovery.Partition curve analysis was originally proposed to evaluate coal washability (Tromp, 1937). Given the limited computational resources at the time, the analytical methods relied heavily on graphical construction and interpretation of the curve. Owing to the simplicity of calculation and interpretation, many of these graphical approaches are still widely used for performance analysis today. The most common calculations are based on the slope of the partition curve at the midpoint. Increased slopes correspond to enhanced separation performance, as a perfect separation exhibits a stepwise transition from 0 to 1 at the desired cut point, that is, an infinitely large slope. One common formulation of this slope, the Ecart Probable, Ep, is derived by evaluating the slope between the 25 and 75 percent recovery points:"

Jan 1, 2016

By Gaballah I.

Elimination of arsenic, mercury and zinc from synthetic solutions containing H;\A.sD4. HgCI2 and ZnCI2 using modified barks was investigated. The pH range was varied from ?1 to 10. The initial concentrations of individual element were 10,100 and 1000 ppm. More than 99 % of mercury and 65 % of zinc cations were removed by the modified bark .. In this case, the modified bark reacts as a cation exchanger leading to the release of ' two protons for every HgII or ZnII fixed by this material. About 30 % of arsenic was eliminated from the solution. This 'low efficiency could be attributed to? the presence of arsenic ,as. anion. Decontamination of a treated industrial effluent containing 4 ppm of ion? metals was performed on a pilot plant scale by the modified bll(k. More than 70'% of these ion metals were eliminated.

Jan 1, 1995

By Swapan Bhattacharya

United States federal and state regulatory authorities require underground mine operators to adopt adequate measures to minimize material damage to the surface caused by nine subsidence. This paper presents an approach to define and determine the extent of material damage due to subsidence from underground coal mining. The basic steps involved in the development of adequate criteria have been enumerated together with the approaches and methodologies used.

Jan 1, 1984

By Brian P. Waagner

Construction law in general and the law of deep foundations in particular continues to develop rapidly, particularly in the areas of risk allocation. Public and private owners are increasingly using contractual disclaimers to shift the risk of differing site conditions to contractors, and courts are increasingly willing to enforce these contractual devices. Perhaps also in an effort to control costs, public and private owners are turning to design-build contracting techniques. While design-build offers many advantages over traditional project delivery systems, it does not answer all of the risk-allocation questions that frequently arise. Even in design-build, problems with unanticipated subsurface conditions and defective design are not easily addressed. Finally, developments in electronic commerce present the potential to transform the construction industry.

Jan 1, 2002

By C Jenkins, M Mativenga, C Stanton, J Gerber

In 2014, Arrium completed an optimisation program on its magnetite concentrator, enabling a reduction in the overall cost base of producing concentrate through an increased ability to treat a wider range of ore types, previously considered waste. The development was the culmination of four years of work, conducted in house by Arrium’s mining development group. The overall intent of the plant design focused on improving the concentrator’s ability to treat a wider range of magnetite ore types. Metallurgical analysis of these feed ore groups outlined a need for more grinding power if production quality was to be maintained and throughput increased. As such, a tertiary grinding circuit was designed which, alongside the rectification of key operational bottlenecks, would allow the plant to continue to produce concentrate at the required specification and rate. The technology chosen for the tertiary grinding application was the XT IsaMillTM, which is known for efficient fine grinding when compared to conventional ball milling. The transfer sizes between the existing comminution circuits were coarsened, allowed for the treatment of different ores at the required rates. The optimisation project was successfully completed in February 2014 after a three month commissioning phase. The initial metallurgical testing and engineering of new equipment proved highly successful with all equipment meeting or exceeding design parameters.CITATION:Stanton, C, Mativenga, M, Gerber, J and Jenkins, C, 2015. Unlocking plant capability through targeted debottlenecking of Arrium’s magnetite concentrator, in Proceedings Iron Ore 2015, pp 185–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By S. -Y. Hwang

An ongoing problem for industry in Korea is effective removal of heavy metals from and safe disposal of spent power plant fly ash. This research endeavor attempts to develop selective separation of Ni from leach liquor using a selective chemical precipitation method. The research was conducted by changing two variables, the pH and the concentration of ions in solution. The effect of other ions present in the system on the separation efficiency of Ni species was also investigated by adjusting OH and NH3 concentrations. In the pH range of 7-9, the chemical precipitation method produced a high yield of Ni by precipitation from the fly ash leach liquor.

Jan 1, 2010

By Zhucheng Huang, Ronghai ZHONG, Tao Jiang, Jun ZOU

The method of reduction roasting and magnetic separation of low-grade, micro- fine disseminated refractory iron ore following granulation with coal produced unexpected success. Pellets of iron ore with diameter between 3 and 8mm were granulated with coal, bentonite and water. The raw pellets and reduction products were analyzed by scanning electron microscopy and x-ray diffraction. Results show uniformly distributed coal powders inside the pellets improved the kinetics of the reduction process and accelerated the reduction rate. Reduction time was higher at temperatures below 890℃, which resulted in the formation of substantial amounts of fayalite. When temperature was increased, micro- fine hematite was then quickly reduced to iron metal and the amount of fayalite decreased sharply. When pellets were reduced at 950℃ for 25min, reduction products with 56.73% metallization rate were obtained. After grinding and magnetic separation, a concentrate with 72.18% Fetot was obtained.

Jan 1, 2015

By Michael Windhager

UltimaTM rolls have been designed for intermediate and finishing stands of rod and bar and small and medium section mills. The rolls and rings are spun cast, with a highly alloyed working layer and a tough nodular iron core. Microstructure and hardness level can be adjusted over a wide range, which allows us to adapt the rolls to differing rolling conditions. After introducing the UltimaTM concept, this paper will describe the results of UltimaTM rolls achieved in various mill applications, like finish rolling of rebar, and slitting. Special emphasis is given to performance gains when using UltimaTM rolls, compared to standard rolls. This paper also examines the impact of UltimaTM rolls on mill and roll shop productivity.

Jul 30, 2018

By Lars G. Olavson

A prototype roof bolt which can be remotely placed by pumping has been developed by the Bureau of Mines. It is known as the "Pumpable Bolt". With the objective of field testing the effectiveness of the pumpable Bolt roof support system a mining machine was developed capable of installing Pumpable Bolts in the normal production cycle of a typical underground coal mine. The machine was built and the pumpable Bolt concept tested and evaluated as a total system in shop and mine tests. The machine was operated in the mining cycle of two mines and pumpable Bolts were installed at both mine sites.

Jan 1, 1976

By J. E. Udd

A core sample for this study was taken from the sulphide ore of the Geco Mine. The subsequent research was based on the assumption that a part of the scattering of strength-grade data could be correlated with variations in the chemical and/or mineralogical compositions of the samples. The results demonstrate clear relationships between strengths in tension and compression and the zinc-iron contents of the rocks.

Jan 1, 1977

By J. Plant

Stream-sediment sampling undertaken to define the regional geochemistry of northern Scotland is described with particular reference to the errors involved. The region is underlain essentially by Moine schists, Caledonian granites and Old Red Sandstone sediments, which are generally characterized by low geochemical relief. Factors in the secondary environment obscure the relationship between trace-metal concentrations in stream sediments and bedrock geology. Investigation of sampling and sample preparation methods indicates that the -100-mesh material is the optimum size fraction for the regional survey of this area: it provides adequate geochemical contrast: it reduced the incidence of spurious high values in the samples investigated and it is available in amounts which are adequate for all the analyses required. Grinding samples improves precision and reduces the preferential volatilisation of metals coprecipitated with hydrous manganese and iron oxides for the optical emission spectroscopic method used initially. A study of the dispersion of metals in the drainage system of an area of Pb-Ba-Mo mineralisation and an area of U-Pb mineralisation, respectively, indicates that a sampling interval of 1 per 2 km2 based on second- or third-order streams is adequate to define anomalous metal concentrations. Regional variation can also be represented on the same interval. Modifications to the sampling procedure to reduce the effects of the secondary environment are complicated by the primary association of Mn and Fe with mineralisation in the area. The ratio of analytical and sampling error to regional variance shows that procedural precision is adequate to prepare regional geochemical maps of northern Scotland, with the exception of Cr, Cu at low concentrations and Pb.

Dec 1, 1971

Arguably the SMC Test® has become the most popular laboratory hardness test in the world with over 17,000 tests having been completed to date, covering over 650 different ore bodies. It is now routinely used in design, optimisation and orebody profiling projects. The test is unique in that from relatively small amounts of drill core it simultaneously provides parameters that are used in simulation modelling of AG/SAG and crushing circuits as well as work indices that are used in power-based equations for predicting the specific energies of AG/SAG/Crushing and HPGR circuits. The very large data base that has been accumulated has provided the opportunity to study the differences in variability from deposit to deposit. This paper describes and discusses the trends that have become apparent from the study of this data base. Recommendations for appropriate selection of sample numbers are also made which are based on these trends.

Jan 1, 2012

By Anderson José Beber

O trabalho apresenta os resultados da aplicação de um novo oxidante moderado em uma grande torre de resfriamento utilizada em sistema de geração de energia de uma grande usina no sul do Brasil. Esta torre de refrigeração utiliza água de efluente tratado (tratamento terciário Esgoto doméstico) como fonte de reposição. Com aplicação desta nova tecnologia, houve uma melhoria tanto no controle microbiológico como na taxa de corrosão. Além disso, a planta foi capaz de aumentar o ciclo de concentração, resultando em economia de água, produtos químicos e menor geração de efluente, possibilitando economia superior a R$ 500.000/Ano, aplicando conceito de reuso.

Oct 30, 2017

By M. Fafard, M. Dupuis, P. Goulet, J. Bédard

Start-up of a Hall-Heroult cell is a delicate task that can affect pot performance and pot life. Modem practices for high amperage cells involve preheating the lining before the molten electrolyte is poured in. Different preheating methods and heat-up schedules are used throughout the industry, and the optimum between a short start-up and damage minimization to the cell is elusive. Direct electrical coke-bed preheating is one of the most common techniques. This practice typically results in a non-uniform surface temperature distribution and can generate detrimental thermal gradients in the cathode blocks. Numerical modeling is an invaluable tool to study this complex problem and can help improve the preheating procedures. The modeling of the mechanical response of the lining is critical to detect risks of cathode block cracking or the development of gaps where liquids could leak into. Taking into account the baking of ramming paste, the quasi-brittle nature of carbon and the contact interfaces between different materials are examples of key elements to consider. A finite element slice model of a cell was built and simulations of different electrical preheating scenarios were performed using the inhouse code FESh++ to demonstrate what can be learned through thermo-chemomechanical modeling. The potential industrial application of the model is discussed.

Jan 1, 2006

By Shu-cai Zhou

"To understand the solidification behavior of austenitic heat-resistant stainless steel (TP34 7) in rotary electromagnetic-field, the influence of electromagnetic stirring in mold (M-EMS) on solidification structure of TP34 7 heat resistant steel in a round billet continuous casting was investigated based on industrial experiments. The results indicate that the excellent billet solidification structure of TP34 7 heat resistant steel can be obtained with appropriate electromagnetic stirring parameters. The solidification structure of TP34 7 heat resistant steel can be remarkably refmed, central porosity and shrinkage cavity can be remarkably decreased and equiaxed grains zone widens was enlarged. The industrial trials verify that the stirring intensity of TP34 7 heat resistant austenitic stainless steel should be higher comparing with plain carbon steel. Due to a higher viscosity, rotating speed of molten stainless steel was 20-30% lower than that of molten carbon steel in the same magnetic flux density.IntroductionIn recent years, the development of ultra super critical (USC) plants is accelerated by the demands of environment protection and energy saving, and USC plants with steam temperature and pressure conditions in excess of 593°C and 24.lMPa respectively were constructed. To achieve the goal, it is important to develop new materials with excellent high temperature strength, superior resistance to oxidation and corrosion at high temperature. Besides, their cost must be low enough to meet the requirement of plants [ 1]. TP34 7H steel is promising austenitic heat-resistant steel, which is used as superheater/reheater tube material and is extensively used for high temperature components and fossil-fired power plants, and suitable to be used in USC boilers plant. This kind steel contains with about 0. 7%Nb and it keeps higher allowable stress and creep rupture strength than TP304 and TP321H [1-2]. TP347H has conventionally been produced by ingot casting followed by forging and rolling. Recently, in order to decrease the production cost, challenging trials to produce these types of alloys by a continuous casting (CC) process have been attempted. However, the solidification structure of austenitic stainless steel is one of the key issues that attract more attention. Due to the low thermal conductivity of TP347H heat resistant stainless steel (much smaller than that of plain carbon steel), pronounced defects during continuous casting of austenitic heat-resistant steel such as coarse columnar, center porosity and coarse bridging, greatly influence mechanical properties of fmished products.A widely used technique in metallurgy is the inductive drive of molten metals using rotational or traveling magnetic fields. Recently, rotary electromagnetic stirring (EMS) has been applied to reducing various defects and improving increase the solidification structure of the metals in the continuous casting of steel, Al-based alloys and Mg-based alloys [3-8]. Electromagnetic stirring of plain carbon and low alloy steel in the continuous casting bloom and slab is well established for improving the quality of cast products [9-11] and is widely used in industry. However, very few literatures on electromagnetic casting of heat resistant stainless steel have reported. In this work, an industrial plant trial was performed to clarify the effect ofM-EMS on the macroscopic quality ofTP347heat resistant steel billet, in which the regularity and mechanism of the influence of EMS on solidification casting billet were discussed."

Jan 1, 2014