Search Documents

By Ke Yang

Drilled shafts are widely used as foundation system for sound walls to resist lateral loads. The design method based on the ultimate lateral capacity, such as Broms method, is often used for sound wall foundation design. Allowable Stress Design (ASD) is currently used for deep foundation design. However, by October 2007, all states Department of Transportations are required to use the Load Resistance Factor Design (LRFD) approach for the design of foundation in highway projects. There is a need to develop a calibrated resistance factor in LRFD lateral design of drilled shafts supporting sound barrier walls. This paper provides resistance factors for design of laterally loaded drilled shafts supporting sound walls using Broms method based on the study using reliability based method and fitting to ASD method. Additionally, the resistance factors for static lateral load tests are recommended. Furthermore, a methodology to update the resistance factors using Bayesian approach by incorporating the on-site full-scale lateral load test results is presented. To illustrate the Bayesian update methodology, two lateral load tests in Colorado were employed to develop the updated resistance factors.

Jan 1, 2007

By K Faure

At Sams Creek a gold-bearing, peralkaline granite pophyry dyke intrudes Ordovician-Silurian metapelite and quartzite. The granite porphyry dyke has a thickness of up to 40 m, extends discontinuously for about 8 km, and intrudes thin lamprophyre dykes along its contacts. The granite dyke and gold-bearing sulphide and quartz-siderite veins within it have been deformed and recrystallised during several phases of folding, the youngest of which is Early Cretaceous.   The unaltered granite porphyry is composed of phenocrysts of perthite, arfvedsonite, aegerine and quartz in a groundmass of the same minerals, with accessory ilmenite, rutile and fluorite. K-Ar dates of amphibole from the granite gave ages of 226 and 246 Ma, but these ages may be a minimum due to resetting during the thermal and deformation events that have affected the area. Unpublished Ar-Ar data on amphibole from the granite show disturbed spectra with high temperature steps around 300-315 Ma, which is consistent with the age of A-type granites in the Buller region. Further age dating of primary and hydrothermal minerals in the granite is continuing. At least three stages of hydrothermal alteration have been identified in the granite. Stage I alteration is characterised by high fO2 magnetite-siderite ¦ biotite, which is cut by thin quartz-pyrite veinlets (Stage II). These are cut by Stage III sulphide, quartz and siderite veins, and pervasive silicification represented by quartz-perthite-albite-rutile ¦ pyrite-siderite-sericite assemblages overprints the earlier alteration stages. Lamprophyre is altered to a siderite-chlorite-sericite assemblage. Stage III sulphide veins are composed of arsenopyrite + pyrite ¦ gold ¦ galena ¦ sphalerite ¦ chalcopyrite ¦ pyrrhotite ¦ graphite, deposited by low fO2 H2S fluids. The gold contains 18-30 wt% Ag and up to 1 wt% Bi. Temperature of vein formation was estimated from vein quartz fluid inclusion homogenisation temperatures (Th 260-355oC, average 330oC), arsenopyrite-sphalerite thermometry (310-365oC) and quartz-albite stable isotope thermometry (340oC). The altered granite and the veins have been deformed, and recrystallised and competent sulphide minerals are fractured and brecciated. Alteration and mineralisation are confined to the granite porphyry and adjacent lamprophyre.

Jan 1, 2004

By Paul Wellman

A computer program is presented that may be used to calculate the bare equipment cost of the major processing units for any hot potassium carbonate gas purification system. The program is designed such that, with only minor modifications, it could be used with a variety of computer systems.

Jan 1, 1968

The heap leaching of base metal ores can be applied within a number of different scenarios, each requiring its own set of parameters to be determined during the metallurgical testwork programme. The occurrence of acid-gangue reactions and its concomitant precipitation reactions is a factor common to all cases, and requires that the optimal irrigation acid strength be found that optimises the combination of extraction kinetics, acid consumption and possible premature blinding of the heap due to precipitation reactions. For the heap bioleaching of base metal sulphide ores the oxygen requirement needs to be determined for the design of the aeration system, and the operating conditions employed need to also facilitate bacterial growth over and above the acid strength optimisation mentioned above. For the heap bioleaching of chalcopyrite, the need to preserve heat in the heap becomes yet a further parameter of critical importance. For the heap leaching of uranium ore a choice is required between either chemical or bacterial oxidation, based on economic and processing factors. Frequently the operating parameters need to be determined for a circuit in which heap leaching is combined with tank leaching and/or pressure leaching. The processing implications and metallurgical testwork approach for each case is discussed.

Jan 1, 2007

By SungWon Park

The efficiency of the current design methods for computing pile resistances is evaluated using field load-settlement tests results. Twelve load-settlement test data for drilled shafts and bored piles were obtained from the literature. These load-test data were fitted using the ?t-z? method. Subsequently, the ultimate resistances were evaluated based upon the failure criteria from following methods: (1) the Davisson?s approach and (2) settlement corresponding to 5% or 10% shaft diameter approach. The ultimate resistances for these drilled shafts and bored piles were also predicted using methods based on the design code from North America (United States, Canada), Europe, and Asia (Japan). The pile resistances determined from field load-settlement tests were compared with those calculated using the design codes. The comparisons show that most design codes predict a conservative resistance for drilled shafts and bored piles. However, in the case of drilled shafts, we find that some of the design codes can over-predict the resistance and, therefore, should be applied cautiously. This research also shows that ?t-z? method can be successfully used to predict the ultimate resistance and the load transfer mechanism for a single pile.

Jan 1, 2009

When it comes to structuring major mining contracts, the two most widely adopted formats are æmeasure and valueÆ and æcost-plusÆ. A problem with both of these formats is the difficultly of aligning the objectives of the mining company with those of the contractor to achieve mutually beneficial outcomes. An alternative contractual arrangement is for the mining company to enter into an Alliance arrangement with the contractor, linking remuneration to mine performance across a range of targets. These targets can change over time as operational requirements change.   The aims of this paper are to: +        outline alternative types of mining contracts, as well as their strengths and pitfalls; +        describe the philosophy behind the Alliance contract at Newmont Waihi GoldÆs Favona underground mine; and +        identify some of the keys to success and pitfalls to avoid when implementing an Alliance.

Jan 1, 2007

By D. R. Wilburn

This summary of international mineral exploration activities for the year 2007 draws upon available information from industry, literature and U.S. Geological Survey (USGS) specialists. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents analysis of the mineral industry based upon these data. Two types of information are reported and analyzed in this annual review of international exploration for the year 2007: 1) budgetary statistics expressed in U.S. nominal dollars provided by Metals Economics Group (MEG) of Halifax, Nova Scotia, and 2) information on regional and site-specific exploration activities that took place in 2007 and compiled by the USGS.

Jan 1, 2008

By H. Zhu, F. Xu, T. Wang

Abstract : The deformation monitoring data of the middle pier of the in permanent ship lock in Three Gorges revealed several interesting deformation phenomena. Conclusions and explanations are made concerning the phenomena in this paper, based on the finite element and engineering geology analyses. Firstly, the fluctuation of the horizontal transformations can be attributed to the alternate excavation of the two neighbouring ship lock rooms. Secondly, the rock mass discontinuities result in the displacement breaks. Lastly, the main reasons for the one-sided leaning phenomena are the natural stress, which is not evenly distributed, and the presence of discontinuities. This paper presents a valuable reference for studying the ‘individual phenomena’ in geotechnical engineering. ZUSAMMENFASSUNG: Die Beobachtungs claten an der Mittelpier deformation bezüglich Permannenter Schiffsschleuse in den Drei Schluchten offenbaren einige interessante Deformationsphänomene. Die Schlußforgerungen und Erklärungen dazu in dieser Arbeit basseren methodisch anf der ‚’ ‘Endlichen-Elemente-Analzse’ und der ‘Ingenieurnissen-Geograhnie-Analzse’. Erstens kann die Fluktuation der horiyontalen Transformation durch die ungleichzeitige Ausgrabung der zwei benachbarten Schiffsschleusenräume verursacht werden. Zweitens resultzert die Diskontinuität der Felsenmasse ans dem verlagerten Bruch. Drittens: Die Hauptgründe für das Zu-einer-Seite-Neigung-Phänomen in manchen Stellen sind der ungleich eigeteilte natürliche Druck und das vorhandersein der Diskontinuität. Diese Arbeit präsentiert eine wertvolle Referenz für die Untersuchung der Sonderfälle in geotechnischen Bau. Résumé: Cet article a analysé sérieusement et profondément , en utilisant des procèdes d’étude par exemple l’analyse d’éléments défini et celle de la condition géographique de traveaux , des règles typiques de la déformation montrées dans les données surveillantes à propos de la déformation des pierres centrales dans les écluses éternelles du Trois Gorges , on en a tiré une conclusion : 1) le changement des chiffres des déplacements horizontaux des pierres centrales est causé par les creusages séquentiels des cannelure voisines ; 2) l’inclinaison au Nord de toutes les pierres centrales entre les deuxième et troisième chambres d’écluse est causée par la différence de la gravitation entre les deux chambres d’écluse et par l’existence de la surface structurale ; 3) l’existence de la surface structurale cause le changement des chiffres des déplacements horizontaux des pierres centrales au niveau profond . Cet article donne une référence utile pour l’étude du ‘ problème d’indivudualité’( ou les situations anormaux) dans les données surveillantes de la déformation des pierres centrales de la génie civile.

Jan 1, 2003

By E. R. Spencer

National Institute for Occupational Safety and Health (NIOSH) researchers conducted an investigation to quantify sound levels and to determine the amount of sound reduction provided by engineering noise controls installed in a talc processing plant. Baseline sound level and sound intensity measurements were performed at the plant and the measurement locations were recorded for comparison to post-control measurements. Follow-up measurements were then made at the same locations after the initial noise controls were installed. The plant subsequently decided to implement additional noise controls and the researchers returned to conduct measurements for a final analysis of all noise controls. The most significant results showed a sound level reduction in the main mill area from a range of 93-104 dB(A) down to 90-94 dB(A), and a total sound power level reduction of 21 dB(A) for air classifying mill 3.

Jan 1, 2008

By T. R. Ellis

The author attempted to concurrently apply the US Uniform Standards of Professional Appraisal Practice and the Australian VALMIN Code to a complex mineral property appraisal assignment. This led the author into many severe difficulties. These difficulties included the high standards needed in the work of others, and information and statements needed from the client. The exercise also highlighted many positive features of both documents. Some conflicts were found between the two documents. Implications and thoughts regarding the development of a set of US minerals appraisal standards are discussed.

Jan 1, 2000

By U. E. Brown

This papery describing the mining methods employed by the Bunker Hill and Sullivan Mining and Concentrating Co. at Kellogg, Idaho, is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the United States. The Bunker Hill and Sullivan mines are situated in the western part of the Coeur d'Alene district at Kellogg, Shoshone County, Idaho. The mines were discovered during the summer of 1885 and except for two short periods of labor trouble, between 1890 and 1900, have been in continuous operation. About 575 men are employed at the mine. The production is about 1,400 tons of lead-silver ore per day. This is treated in the company's concentrator and smelter at Kellogg.

Jan 1, 1931

By Zsuzsanna Zborovszky

Study of the energy transfer from an inductive circuit to the discharge under the conditions of the minimum discharge voltage being smaller than the source voltage. Analysis of the effect of the electrode separation speed on the duration and maximum power amplitude of the discharge. Recommendation for optimal electrode setting. Experimental data on the variation of maximum discharge power required for ignition as a function of volumetric gas content for methane-air and propane-air mixtures. Experimental determination of the ignition limit for discharges derived from a 24, 15, 10 and 6v inductive-resistive circuit in 8.3% methane-air mixture by using the PTB breakflash with Cd disc and W wires, and also with Cu disc and BeCu wires. Method for calculating ignition limits for other source voltages.

Jan 1, 1978

By H. G. Denkhaus

Comment on ?The evaluation of rock brittleness concept on rotary blast hole drills? in the Journal of SAIMM, vol 102. no. 1. pp. 61?66 Comment on ?Correlation of specific energy with rock brittleness concepts on rock cutting? in the Journal of SAIMM, vol 103. no. 3. pp. 163?171by R. Altindag Foreword Some thirty years ago it was almost customary that articles in South African technical and scientific journals were followed up by discussions in which the reader(s) expressed criticism and/or added to the information contained in the article. This custom has obviously died out, be it that the articles are nowadays of such a high standard that nothing can be added or be it that the receivers of the Journal suffer from an information inflation and do not read the articles anymore. I now have the temerity to offer a discussion to an article that recently appeared in the journal, namely ?The evaluation of rock brittleness concept on rotary blast hole drills? by R. Altindag (J.S. Afr. Inst. Min. Metall., vol, 102(2002), pp. 61?66.

Jan 1, 2003

By Seung-hoon Lee

The use of piled raft foundations has been considered as an economical alternative to conventional piled foundations because a portion of the applied load is carried by the raft in the design of piled raft foundation. In analyzing the behavior of a piled raft foundation as a settlement reducer, an accurate estimate of settlements of the system should be made on the basis of the understanding of nonlinear behavior of piles in layered soils as well as the interaction between the raft, soils, and piles. Although the 3-dimensional finite element method and simplified analysis methods have been used for the design of piled raft foundations, these methods were found to be inadequate for the practical purpose or could not consider the interactions properly. This study developed an approximate hybrid method of analysis to be used for the practical design of piled raft foundations considering pile-soil, raft-soil, pile-soil-pile and raft-soil-pile interactions. In the presented method of analysis, the settlements of the system are estimated satisfying the compatibility of two separate models which are the flexible raft model consisting of 2-dimensional finite elements supported by springs representing soils and piles, and the group-pile model embedded in layers of soil having different properties. Comparisons with other analytical methods as well as a 3-dimensional FEM program were made to verify the sufficient capabilities of the proposed hybrid model for application to practical design and analysis of piled raft foundations.

Jan 1, 2008

By E. L. Martheleur

Introduction In October, 1945, the Coal Division of the Institute appointed a Committee on The Use of Electricity in Coal Mines, with the following terms of reference: ?To study under which conditions in each deposit the use of electricity can be brought closer to the coal face and which types of electrical machinery can be recommended?. It was not until the beginning of this year (1946) that the Committee had a chance to convene and .discuss the conclusions which are embodied in this report. Mr. McLeod, as Chief Electrician of the Dominion Coal Company, is intimately concerned with that Company's installations, and Mr. McIsaac, as Electrical Inspector of Coal Mines for Nova Scotia, is well acquainted with installations in all coal mines in the Province. The knowledge of both has been very valuable in helping to draft this report.

Jan 1, 1946

Jan 1, 1968

By R. Thomason

Thank you Dr Barcza, President of the South African Institute of Mining and Metallurgy, for inviting me to share our experiences in Australia as regards the competency movement and my Association?s experience in assisting engineers become managers. This is my second visit to South Africa, and I am struck by the similarities between our countries. This extends to the professional issues associated with engineering and competencies in particular. I propose to outline two exciting stories today. ? Development of competency standards for professional engineers in Australia. ? Development of a management programme which has assisted professional engineers regain positions of leadership in Australian industry and government. First of all I would like to outline the Association of Professional Engineers, Scientists and Managers, Australia(APESMA).

Jan 1, 1997

By T. J. DeMull

The business of heap leaching requires accurate forecasting of metal production from the heaps. Business forecasts typically follow a format that project periodic (monthly, quarterly, or annual) product shipments based on anticipated operating results, e. g., tons of ore placed, grade of ore, and rate of leach extraction. Since revenue and cash flow are dependent on the metal production stream, forecasts of metal production are very important for project evaluation and business planning purposes. Nevertheless, production forecasts, particularly for new heap leach projects, have been prone to errors. The present paper identifies some of the pitfalls that would be encountered in preparing production forecasts for new heap leach operations and provides a checklist of considerations to assist in preparing a forecast. Also, the paper presents a case study of copper production forecasting used for the Sanchez Project, a heap leach operation located near Safford, Arizona, that is presently under development by AZCO Mining, Inc.

Jan 1, 1995

The paper presents the development of an integrated computer aided design and planning of open cast mining, with the use of object-oriented modelling and geoinformation technologies, on the example of interaction of the subsystems on planning optimisation and freight traffics.

Dec 6, 2010

By Bernardo Araya López

Dada la competitividad que existe en el ambiente empresarial durante los últimos quince años, las empresas reaccionan rápidamente ante los cambios del mercado. En este sentido, el presente trabajo señala el proceso de organización que la empresa debe considerar para lograr sus objetivos y metas. De forma, que la gerencia como concepto de gestión, genere confianza y responsabilidad sobre sus subordinados y potencie las habilidades de sus trabajadores.

Sep 13, 2001