Search Documents

By Y. Paul Chugh

NIOSH and the Illinois Clean Coal Institute are funding studies on characterization of coal and quartz dust in Interior Basin mines since 2009. Coal dust characteristics vary significantly and, are vital for the development of the engineering controls. This paper presents wettability characteristics of coal dust with respect to its chemical and physical properties, since wettability is considered to be a primary dust control technique. Particle size distribution, inter-particle interactions during wetting and quartz associations with organic and inorganic matter in coal seams is critical for understanding wetting phenomena. Silica content in the un-wetted fractions was found to be very high during wetting tests. Wetting of quartz may be limited by its association to hydrophobic materials as well as buoyancy forces resulting from particle size characteristics and particle-particle interaction in the wetting agent. Temperature of the wetting solution and effective contact time between dust particles and water droplets are found to be two important variables affecting the wettability. The characterization data obtained from this study can be utilized to develop engineering controls.

Jan 1, 2011

By Mark L. Requa

(San Francisco fleeting, October, 1911.) DURING the past two years California has developed a new and important oil-field : I refer to Midway. This field produced the famous Lake View gusher, which is credited with a total production in excess of 8,000,000 barrels. Fortunately for the oil industry of the State, this well is now a thing of the past, and nothing save a great crater-like opening marks its location. The pipe is entirely worn away and gone ; and it is a matter of serious doubt if there can be anything done that will cause the well to produce again. Fortunately, also, there have been no, other wells in that field or elsewhere throughout the State that in any way compared with the Lake View. Midway is noted for large wells, of from 500 to 2,000 barrels production; but the decline is rapid, and a few months serve to bring the output down to a few hundred barrels. In the oil-territory heretofore blocked out as proved and probable, there have been, during the year, many changes. Some areas which were expected to be fairly productive have apparently failed; others, more strictly "wild-cat," have come in; while in some of the older fields there are properties which are beginning to show evident signs of exhaustion. The total area of proved territory will therefore probably suffer but small increase, when balances are struck off. The increase of new area has come from extensions of the Midway field, the development of a field in Lost Hills and Belridge, and extensions of the Fullerton-Whittier field in southern California. In these later developments, down to date, the fresh area absolutely proved is not much in excess of 3,000 acres. Recent developments in Coalinga indicate the possible extension of that field to the south, but at great depth. Coalinga is still the most northerly field of any consequence in the State. The Kettleman Hills have hitherto brought in nothing, although a

Apr 1, 1912

By Arun Verma

Thermal energy storage offers a means of effecting significant costs savings and conservation of premium fuels. Na2SO4 has been found to be a good material for storing thermal energy in the medium-temperature range, mainly because of its dimorphic nature and high heat of transition. Basic data and development of the salt to a practically usable block are discussed.

Jan 1, 1978

By Silvana Costa

In the last two decades, there have been nearly no new mining towns built in Canada. Governments and mining companies have viewed long distance commuting (LDC), commonly known as fly-in-flyout or fly-in mines, as a way to avoid problems associated with building a new community and providing for its sustainability after mine closure. LDC is also considered more cost-effective than building a mine town. The intensification of the use of LDC in the Canadian mining sector has been quite rapid, particularly in northern regions. However, LDC has implications to employees, their families and communities, which deserve further examination, particularly considering the significant expansion in Northern mining and Aboriginal participation in this sector. This paper presents a review of the major issues in long distance commuting, both from an industry and community perspectives. It is a result of preliminary investigation for a PhD research project that will be pursued by a Bridge Fellow and UBC Mining Sustainability Working Group member, and guided by an interdisciplinary research team at the University of British Columbia (UBC). The Bridge Fellowship Program is research-training program linking the UBC?s Faculties of Medicine, Engineering and Graduate Studies. Its mission is to develop creative evidence-based prevention measures for public, environmental and occupational health problems. The SWG is an interdisciplinary student group based in the UBC Department of Mining Engineering, committed to respond to the complex sustainability-related challenges currently faced by the mining industry. In other to pursue this project, it is paramount that industry and local communities alike participate in the development and clarification of research questions as well as in the research design. It is hoped that this paper will function as an invitation for industrial and community partners for such study. The main themes identified for this research are occupational health and safety of LDC employees, family life impacts and community health impacts of this model of resource development.

May 1, 2004

Measurements from an old survey are being machine processed as a pilot project in the development of a computer-assisted method of structural mapping in shield areas. The key element in the system is a field data sheet which requires the geologist to determine a textural hierarchy in each exposure. The pilot system is limited to orientation analysis and utilizes a prior textural analysis, but this would not usually be a problem in utilizing the system ab initio for exploration. A data processing system of this general type offers promise of considerably increased productivity of field geologists by reducing compilation time and improved technical supervision through centralization of processing, and would make structural analysis an economically viable tool in mining exploration and development.

Jan 1, 1969

By G. L. Gates

The Bureau of Mines in cooperation with the City of Long Beach) Calif.) studied some physical factors effecting the deposition of barium sulfate scale in oil-well rotary pumps. Freshly formed barium sulfate was obtained by combining sulfate in sea water with barium from a barium chloride solution. The rate of scale deposition was measured quantitatively by weighing the pump impellers and diffusers. The results of the tests showed that coating the impellers with plastic significantly reduced the rate of barium sulfate deposition.

Jan 1, 1967

The mine surveillance and communication system hereafter described provides continuous local and remote monitoring of several parameters critical to normal mine operation at each of ten underground sites in the Bruceton Research Mine. The techniques employed are well proven and have been care-fully chosen to provide the best solution to the technical problems involved while giving special attention to economic considerations.

Jan 1, 1973

By J. L. Eakin

Systematic flooding was introduced into Nowata County, Okla., in May 1931. The results of this means of stimulating the nearly depleted Bartlesville reservoir in the county has been the subject of four Bureau of Mines Reports of Investigations.2-5/ This report presents a discussion of four full-scale water-flooding projects in the Delaware-Childers field and 1 pilot project in the Curl Creek field (fig. 1). All five plants have been in operation for only a few months. Although substantial increases in the rates of oil production have been obtained 1 by the injection of water, the projects are of particular interest at this time because of the novel methods of operation and new equipment that are being employed. One project utilizes a portable "package" plant designed for a pilot operation. All of the controls for this project are centrally located. The design makes it possible to remove the test plant to another location if the project is unsuccessful or if the unit is to be replaced by a larger plant. This project also utilizes diatomaceous-earth filters successfully for the first time and makes use of plastic pipe. Another novel feature of the operation is the aeration of Arbuckle limestone water through an airlift in the supply well.

Jan 1, 1955

The rock mass classification systems were developed for different functions, including support selection, excavation method selection and the determination of rock mass engineering properties for excavation design, among others. This explains in part why we have several rock mass classification systems. It is often cautioned that the rock mass classifications are to be used for preliminary excavation support design, but this caution is now often overlooked and detail/final support design based on the rock mass classification systems. This paper advocates differentiating between rock mass classification for pre-excavation support planning and rock mass classification for at-face excavation performance assessment. It is concluded that most at-face excavation performance problems are attributable to confusing the virgin rock mass rating with the rock mass rating on exposure during excavation, and that this observation is independent of the method of excavation. Procedures are then presented for virgin rock mass rating and for at-face rock mass rating/assessment during excavation.

May 1, 2009

By Dennis Travagini Cremonese

In the early stage of front end studies of an Iron Ore Project, the sizing of surge capacities and stockpiles are normally assumed based on the experience of the study team. Understanding and sizing of these capacities at the early stages of the project are important for future stages of the project as drastic changes in sizes will impact the economics of the project at that stage. An innovative user configurable high level dynamic modeling tool has been developed to assist in speedy evaluation of assumptions made by the study team. This model incorporates systems or facilities that are commonly used iron ore project from mine to port. This model includes subsystems that will simulate all the logistical components, major process plant systems required for an Iron ore project. The output data provided by this high level dynamic simulation tool will enhance the confidence level of engineering carried out during the early stage of the project. This paper discusses the innovative tool capabilities and a test case comparing various techniques used in iron ore project front end studies.

Aug 1, 2018

By Avery H. Reed

RECORD production of crude petroleum, lime, crushed marble, and talc highlighted the mineral industry of Alabama in 1963. Among the States, Alabama ranked second in the production of bauxite, third in the production of scrap mica and native asphalt, and fifth in iron ore. The mineral industry of Alabama was dominated by mining and processing coal and stone, the manufacture of cement, and the production of crude petroleum, which together comprised 86 percent of the total value of production, compared with 82 percent in 1962. The iron-ore industry continued to decline; in 1959 the value of iron ore produced was 12 percent of the total State production value; in 1960, 11 percent; in 1961, 10 percent; in 1962t 8 percent; and in 1963, 5 percent.

Jan 1, 1964

By H. J. Heinen

To maximize productivity through improved minerals processing technology, the U.S. Department of the Interior, Bureau of Mines, is investigating particle agglomeration techniques as a means of increasing the percolation rates of leach solutions in heap leaching of clayey gold-silver ores. Simulated heap leach experiments were conducted on 50-pound charges of ore that were contained in 5.5-inch-diameter columns, 5 feet in height. Results indicated that the percolation rate of cyanide leach solution could be enhanced markedly by mixing the ore with controlled amounts of lime, flocculants, and water, and then aging the mixture prior to the column leach step. Experimental results obtained on 20-mesh silver tailings and gold ore crushed to 3/8 inch and to 1 inch showed that it was possible to increase percolation rates as much as 100-fold without sacrificing silver-gold extraction. Larger scale tests conducted in 24-inch-diameter, 16-foot-high columns closely paralleled bench-scale results. By improving percolation leaching, these techniques have the potential of helping to solve environmental problems associated with tailings disposal as well as making an important economic impact on gold-silver recovery operations. Investigations are continuing to develop binders superior to lime for particle agglomeration pretreatment.

Jan 1, 1979

By L. D. Schmidt, H. G. Graham

Several processes for the production of ultra-clean coal for electrode carbon were developed in Germany prior to and during World War II . These processes have been investigated since the end of the war by the British and U. S. Government missions . As the reports of the investigations are not readily available to the public , it is the purpose of this paper to present the information which has been obtained regarding the methods by which ultraclean coal was produced . Almost all the ultra-clean coal was used in the manufacture of electrodes for the production of aluminum and magnesium . Standard raw materials for making these electrodes are pitch coke and petroleum coke , which are nearly ashless . The inclusion of ash in the electrode carbon results in lowered efficiency and impure metal from the reduction process . Petroleum coke and pitch coke were in very short supply in Germany during the war , so that it was necessary to augment the supply with carbon produced from coal . In the emergency , methods were developed to clean coal which had never before been economically feasible . However , a demand for nearly ash-free coal might develop in the United States if a shortage of petroleum coke were to occur at the same time as a strong demand for light metals . Other uses of ultraclean coal are in direct hydrogenation of coal , in production of activated carbon, and for special fuels . Specifications for electrode carbon are rather severe owing to the necessity for producing pure metal . Maximum amounts of impurities allowable in American practice are as follows : Total ash , 1.0 percent ( in finished coke , 0.7 percent ) Silica , 0.08 percent Ca or Na, or their sum , 0.12 percent Sulfur , 2.0 percent Ba , Ni , Cr , Mn , Co , and V are objectionable in very small amounts . The most important process for ultra cleaning of coal in Germany was froth flotation . Froth flotation had been used widely there to process washery -water sludges and to recover coking coal from high - ash fines . Its use was indicated , therefore , when the demand for ultra low-ash coal arose . In two plants the coal cleaned by froth flotation was treated with acid or caustic to lower further the ash content . Another process used on an industrial scale was that of dissolving the coal substance in the middle oil from direct hydrogenation of coal under controlled pressure and temperature . The resulting paste was heated, filtered , and the oil distilled off . The residue was a low-ash organic material that could be carbonized for electrode carbon or could be hydrogenated directly . Several other processes had been developed to the laboratory or pilot - plant stage but had never been used on a commercial scale . These processes included cleaning by centrifugal action , cleaning by electrostatic action , and cleaning by forming a paste with oil in water . The coal-preparation plants at the Carl Alexander mine , Augusta Viktoria mine , and Kőenigin Elisabeth mine are described in Bureau of Mines Information Circular 7389 : " Coal Preparation Practice in Western Germany" , by Thomas . Fraser and M. G. Driessen . Most of the special equipment used at these plants is described in the above publication .

Oct 1, 1948

By Tassos Grammatikopoulos, Vladimiros Papangelakis, Douglass Duffy, Cheryl Washer, Srinath Garg

Flotation operations in Sudbury, Ontario, seeking to separate pentlandite and chalcopyrite from mixed sulphide deposits, produce pyrrhotite tailings that have been disposed of in tailings ponds for over 50 years. These reactive tailings are viewed as waste, despite containing ~0.8 wt% Ni, and represent an environmental liability because of their acid mine drainage (AMD) potential. Given the large quantities of pyrrhotite currently stored in Sudbury, and declining ore grades elsewhere, these tailings have shifted from being viewed as a waste to a potential resource. Recent advances in the bioleaching of low-grade sulphide ores have raised the prospect of bioleaching as a potential low-cost processing option. However optimization of this proposed process requires a thorough understanding of the mineralogy of the pyrrhotite tailings that would be leached. The work presented here addresses the characterization of two distinct Sudbury pyrrhotite tailings, namely from the Vale and Glencore operations, using electron microprobe, XRD and QEMSCAN analysis. Particular focus is given to how the mineralogy may affect bioleaching as a processing option, through the deportment of nickel and the various phases present

Jan 1, 2015

This report is in fulfillment of Contract H0230031 awarded to Bituminous Coal Research, Inc., on May 23, 1973. The scope of work to be performed under this contract was divided into four phases: Phase I - Design, Phase II - Construction, Phase III - Field Demonstration, and Phase IV - Analysis and Final Report. During Phase I, an agreement was finalized with the Rochester and Pittsburgh Coal Co. for conducting field tests of the proposed shearer spray systems on a longwall panel in the company's Jane Mine in Indiana County, Pa. A drum was then designed which could be used on the Eickhoff shearer, Model EW170-L, being used on this longwall and which would utilize the following spray systems: 1. One spray nozzle located in front of each cutter bit with the jet directed at the cutting surface. 2. One spray nozzle located in back of each cutter bit with the jet directed at the back of the bit. 3. Standard Eickhoff nozzles located in a header along the drum scrolls. 4. A fixed header mounted on the shearer directly behind the drum to simulate the spray system originally used on the Eickhoff shearer.

Jan 1, 1976

By J. M. WADSWORTH

The purpose of this bulletin is to describe the methods of constructing and operating representative types of plants in the United States used for removing the light hydrocarbons from petroleum by continuous distillation, such plants being commonly known in the trade as topping or skimming plants. In the discussion of each plant an endeavor has been made to arrange the text similarly in order to facilitate comparison and to emphasize the important features. The various experimental values for the specific and the latent heats of the oils apply approximately to the oil treated. Careful experiments with each oil and its commercial fractions were not justifiable in view of the purpose of this report. It is regretted that limitations for recording data at the different plants made impossible the determination of a heat balance for each, which would have provided an equitable method of comparing efficiencies. The writer has confined himself to a comparison of the relative efficiencies of the distilling apparatus alone by the following method: Effi . f till d tt" _ Heat theoretically required. ciency 0 SIS an se mgs - Heat content of fuel consumed. The plants described are all in California where the topping industry has had its growth accentuated by the character and the use of the oil handled. The scarcity of suitable coal made the adoption of other fuel necessary, and the heavy oil of California supplied the need. To raise the flash point and to dehydrate this oil, various plants have been developed. However, the topping industry is represented in other fields; the Roxana Petroleum Co. of Cushing, Okla., and the Warner-Quinlan Asphalt Co. of New Jersey, are operating Trumble plants, and Texas and Oklahoma operators have been experimenting with different pipe retorts for continuous running. In addition to the reasons for topping cited above, in California topping has other purposes which give the plants practically a universal field in the oil industry. These additional purposes are (1) to remove the lighter constituents of the oil prior to storage for a long period, thus reducing the losses from evaporation, (2) to dehydrate and clean the oil, and (3) in conjunction with a complete refinery, to remove the lighter fractions cheaply and quickly, leaving a residue to be rerun for lubricants, coke, and other products. The reader in studying a plant for possible adaption to his own use should note that local considerations enter into the design and size of a plant. Several questions present themselves, as follows: 1. What type is suitable for the oil? 2. How much money is available for construction? 3. Will the volume of residuum be large enough for heat exchange with the crude? 4. Can the heat content of the vapors be used to reduce the cooling-water requirements? 5. What method will best recover the heat from stack gases? 6. Are the various pieces of apparatus adequate in size and best adapted to their purpose? 7. Is every possible provision made for the recovery of waste heat? 8. What products will be made, and what volume of each? 9. Is there provision for the recovery of light vapors? 10. Will the saving of fuel justify the capital and maintenance charges on the regenerative apparatus contemplated? It is regretted that information concerning the operation of topping plants with eastern and Middle West oils is not available. The writer carefully canvassed the Middle West, but did not find a plant where operation had progressed beyond the early experimental stages and reliable figures could be furnished. The reader will find fuel economy and heat recovery emphasized throughout the descriptions. The conservation of the available petroleum supply is of the utmost importance, and the Bureau of Mines presents this paper to encourage the hearty cooperation of operators to that end. The Baume gravity scale used throughout the report is that of Tagliabue with a modulus of 141.5 for conversion to specific gravity.

Jan 1, 1919

By Paul J. Bourassa

Alin de pourvoir aux besoins d'hébergement des quel¬ques 1600 employes qui travailleront dans toutes les spheres opérationnelles de l'exploitation du gisement du Mont-Wright, ainsi que de leurs families, Quebec Cartier a dû, avec l'aide de conseillers reconnus, et /a participation de ses employes résidant a Gagnon, étudier tour les nouveaux établissements résidentiels nordiques des dernières années tout au Canada qui dans lee pays scandinaves afin d'être en position de coneepter une agglomeration moderne répondant a toes les besoins de see future résidants. Les pre¬miers residants ont pu passer Noel 1972, et maintenant les logements prévus et construits sont °coupes a 92%.

Jan 1, 1977

By The Staff

"IntroductionThis paper lists typical liner performance data for various grinding mills at the Noranda, Waite-Amulet, Pamour, and Hallnor mines, and concludes with a comparison of these data, based on wear per square foot of lined mill shell area. Flow-sheets for each of these plants will be found in the reference cited.General InformationTwenty-eight ball-mills and one rod-mill are used by the Noranda organization for grinding ore. These mills, which are shown in general outline in Plate IV, are all of the overflow type and have a cylindrical shell attached to dished heads.Most of them are serviced by hand-operated cranes and none by power cranes. During re-lining, portable tugger hoists are employed to lift the liners and, frequently, to install them in place.The mills vary in length and diameter and the ratio of end liner area to breast liner -area consequently ranges from 1. 6.75 in a 5 ft. by 14 ft. mill, to 1:2.28 in an 8 ft. by 8 ft. mill."

Jan 1, 1950

By R. F. Zaffarano

Intergrated energy balances and energy flows were constructed and quantified for State, regional, and national levels from four separate supply and demand commodity balances for coal, dry natural gas, petroleum and natural gas liquids, and utility electricity. These commodity balances were integrated by source and sectors through conversion and aggregation of their components to energy equivalents expressed in British thermal units (Btu). A summarization of the total gross energy components of supply and demand for commercial energy derived from direct fuels, hydropower and nuclear power, based on individual States and regions, is tabulated for 1960 and 1965. Pertinent computerization details and more than 500 individual State and regional printout tables, in both original commodity units and Btu's, are shown. Using these data, energy flows between States and regions were calculated to identify surplus and deficit energy areas. Report emphasis is on the conceptual aspects of integrated energy balances, rather than on the development of missing State energy data.

Jan 1, 1969

By M. L. Harris, J. Organiscak, S. Klima, I. E. Perera

"The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted underground evaluations in an attempt to quantify respirable rock dust generation when using untreated rock dust and rock dust treated with an anticaking additive. Using personal dust monitors, these evaluations measured respirable rock dust levels arising from a flinger-type application of rock dust on rib and roof surfaces. Rock dust with a majority of the respirable component removed was also applied in NIOSH’s Bruceton Experimental Mine using a bantam duster. The respirable dust measurements obtained downwind from both of these tests are presented and discussed. This testing did not measure miners’ exposure to respirable coal mine dust under acceptable mining practices, but indicates the need for effective continuous administrative controls to be exercised when rock dusting to minimize the measured amount of rock dust in the sampling device IntroductionTwo recent regulations have modified operators’ rock dusting schedules in order to meet compliance standards. First, the 80 percent incombustible requirement in intake entries has increased both on-section and out by the- section rock dusting. Secondly, the recent change to the respirable dust regulation has increased the number of respirable dust samples taken per sampling cycle. Previously, when only five samples were needed bimonthly, rock dusting could be scheduled to not interfere with the respirable dust sampling schedule.The significant number of samples now required under new regulations, combined with the need to maintain 80 percent total incombustible content in active mining areas, require the schedules for respirable dust sampling and rock dusting to overlap. Although rock dust is considered a nuisance dust in relation to U.S. Mine Safety and Health Administration (MSHA) sampling, these overlapping schedules raise concerns about the amount of rock dust that potentially is included in the sample. Additionally, the respirable dust maximum was lowered from 2.0 mg/m3 to 1.5 mg/m3 effective Aug. 1, 2016, increasing concern that rock dust contamination may be an issue (MSHA, 2016). Currently, the acceptable practice is to apply administrative controls such as keeping the miners upwind during rock dust application, or to schedule rock dusting during a maintenance shift when the number of miners present is lower."

Jan 5, 2017