Search Documents

By Robert L. Lagace

The purpose of the work reported herein was to investigate whether available telephone multiplexing equipment offered a means to rapidly upgrade the traffic-handling capacity of present mine telephone systems and provide for selective calling for safer and more efficient mine operation. Common sense was used to decide whether or not an item could be termed "available." Since conventional telephone gear is not designed to interface pager phones for example, existing shelf items would require adapters to compatibly interface these two types of gear for independent operation over the present single twisted pair used in mines. These and similar small items were allowed, but if a system required any extensive design work to adapt it for the mines, we ruled it "not available."

Jan 1, 1975

By S Natsui, Y Goto, S Kawanishi, J Takahashi, H Nogami

The demand for copper increases yearly, and further improvements in copper smelting efficiency using flash furnaces are required. This study was conducted to understand and promote the interfacial reaction associated with the collision of silica flux and iron oxide particles, ie the formation reaction of fayalite slag, in the reaction shaft of the flash furnace. High-temperature microscopy was used to observe the reaction behaviour of a 2 mm granular SiO2 reagent in contact with micrometreorder- sized FeO reagents in situ. When the amount of FeO was lower than the stoichiometric amount with SiO2, the molten slag formed at the interface between FeO and SiO2 diffused into the SiO2 particle before dissolving the remaining FeO particles. It did not contribute to the subsequent reaction, and despite having the lowest amount of FeO among the samples in this study, many unreacted FeO particles remained on the surface of the samples after testing. On the other hand, under conditions with high FeO content and close to the eutectic composition of the FeO-SiO2 system, a liquid phase formed from low temperatures, gradually increasing in volume and eventually completely dissolving the 2 mm SiO2 grain. These results indicate that the early-stage slag is essential in increasing the interfacial area between FeO and SiO2 and facilitating the supply of FeO to SiO2. In other words, the FeO/SiO2 determines the amount of liquid phase and significantly influences the subsequent interfacial reaction rate between FeO and SiO2. Therefore, the local FeO/SiO2 of the particles falling down the reaction shaft should also be optimised to ensure early slag formation. Meanwhile, the time required for 2 mm SiO2 to complete the reaction for the temperature history employed in this study was significantly longer than the particle residence time in the reaction shaft. Further detailed investigation of the effects of silica flux particle size, composition, and reaction temperature on the reaction time will help find the conditions under which the reaction of silica flux can be completed in the reaction shaft. These kinetic approaches could contribute to future innovations in the copper smelting process using flash furnaces.

Jun 19, 2024

By W. R. Ingalls

IF, in this study of the outlook for the copper industry of the United states, I find myself assuming to be prophetic in some respects I shall express myself with hesitation and with the foresight that after the end of the war with Germany the war with Japan may continue; anyway there is sure to be an uneasy period before copper and the other metals begin to flow smoothly through the natural channels of consumption. It is mainly my purpose to survey conditions and suggest some probabilities, or possibilities, rather than to prophesy. In interpreting them it will be necessary to make certain aasurnptions, among which will be (1) expectation of a rise in the general price level,, which so far has been one-sided; (2) continuance of the k. tariff on copper imports; and (3) lock-up of government-owned copper as a military re- serve. Of these assumptions the first is indicated by the lessons from economic history, and by current symptoms. The second and third depend upon political action by Congress.

Jan 1, 1944

By Allan MacRae

Freeport-McMoRan Inc. operates an ISASMELTTM furnace for the smelting of copper concentrate at the Miami Smelter in Claypool, Arizona. In May 2017, the furnace was restarted after incorporating newly designed copper cooling elements from just above the tap hole to the underside of the roof. The objective of the improved cooling design was to extend campaign life by eliminating existing failure mechanisms with the wall refractory. In addition to upgraded bathline coolers and complete coverage of the gas offtake transition, or ‘kettle’, with plate coolers, a novel arrangement of coolers was installed in the remaining freeboard area. The shell required significant cutting and re-stiffening, as well as extensive modification of the cooling water piping. Based on performance observed to date, it is expected that smelter throughput will be increased due to extended ISASMELTTM refractory campaign life.

By Scott, Turner

MY whole life has been spent in the mining business, PO I naturally tend to address my remarks particularly to the newly-graduated mining and metallurgical engineers among you. To a certain extent, all forms of engineering principles are involved in the training of the mining engineer, and most sorts of engineering are certainly utilized by him, so every one of this graduatins class is concerned with the field I propose to discuss.

Jan 1, 1932

By H. M. Thorne

The Union of South Africa has been interested in oil shale for a long time, and deposits of oil shales, torbanites, and similar rocks have been found in many parts of the country. (Fig. 1.) Samples differ markedly in oil yield and in the characteristics of the oil. The strata vary in thickness, and most of the deposits that have been found are in unfavorable locations because of remoteness from markets or absence of transportation facilities. This report deals mainly with the torbanite deposit near Ermelo, Transvaal, in the Union of South Africa, and the operations of the South African Torbanite Mining and Refining Co., Ltd. (hereafter referred to as Satmar), in mining the torbanite, retorting it, and refining the crude oil.

Jan 1, 1954

By G. Miller

The design of solvent extraction plants has been generally based on the assumption of steady operating conditions in both the settler and the mixers. Recent experience with both large and small plants has shown that this is not the case. Mixer transients include start up aqueous locking and partial phase separation in secondary mixers. Both of these lead to either reduced plant capacity or overflow of upstream mixers. Analysis of the hydraulic pressure profiles has generated new design methods to eliminate the effects of the partial or complete phase separation. Further, changes to the method of specification and selection of both primary and secondary mixers have been made to eliminate the onset of partial separation during operation. Observation of settler operation has shown that it is also a dynamic process, even under ‘steady state’ conditions. Four different transient phenomena have been identified that lead to internal circulating flows, poor disengagement of fine secondary haze, and erratic and high entrainment levels in the discharges. A first approximation analysis has shown that there are significant pressure differentials within settlers and these change along the length and with phase separation rates. A technique to control the effects of these transients has been developed which allows plant performance to be improved beyond ‘standard’ expectations. The design and selection of the settler internals is described.

Jan 1, 2001

By C. D. Ashley, X. P. Garzon-Villalba, R. M. Lopez, T. E. Bernard

Federal standards for refuge alternatives (RAs) mandate that they not exceed a Steadman apparent temperature (AT) of 95 °F (35 °C) at an assumedmetabolic rate of 325W, a limit that appears to be arbitrary. Occupants in an RA spend most of their time at rest (a metabolic rate less than 325 W), and thermal equilibrium can likely be maintained at an AT > 35 °C. The purpose of this study was to examine the upper limit of sustainable heat stress during 4- and 8-h exposures at rest. Five men underwent five 4-h trials (phase 1: AT range 39 to 49 °C, 90% rh) and five 8-h trials (phase 2: AT range 46 to 56 °C, 90% rh) in a semi-recumbent position. Descriptive statistics for gastrointestinal temperature (Tgi), heart rate (HR), systolic and diastolic blood pressure (SBP and DBP), sweat rate, fluid intake, urine color, urine specific gravity (USG), and changes in body mass are reported. Mean Tgi for all trials ranged from 36.9 to 37.3 °C, and mean HR for all trials ranged from 61 to 75 bpm. To determine the effects of increased heat exposure, differences in heat strain between 4- and 8-h trials were examined via repeated measures analysis of variance (ANOVA). As AT increased, there were no significant changes in ?Tgi and ?HR from 1 to 4 h in the 4-h and 8-h trials. During the 8-h trials, as AT increased, there was a difference in ?Tgi between 4 and 8 h. In conclusion, there was support for sustainable exposures resulting in no significant increase in physiological strain at an AT greater than 35 °C AT, with a sustainable limit (no increases in Tgi due to increases in AT) below 46 °C AT. Although the participants were not representative of coal miners, the results provide support for sustainable exposures greater than 35 °C AT at an average metabolic rate of 155 W.

Nov 8, 2019

By B. J. Nelson, F. N. Rhinos

Studies upon the rates of oxidation of copper alloys containing small quantities of the alloying elementsl,2 have shown that steady growth of the scales at predictable rates is limited to a small concentration range and to oxidation at temperatures above 600°C., whereas unpredictable and erratic oxidation behavior is found with alloys containing larger additions and at low temperatures. The latter effect appears to be associated with modifications in the geometric disposition of the oxides. At low concentrations of the baser elements in copper, simple oxidation behavior is typified by the formation of two distinguishable zones of oxidation: (I) a subscale composed of discrete particles of the oxide of the alloying element embedded in substantially pure copper and (2) an external scale composed of cuprous oxide (with a very thin layer of cupric oxide on the outside) containing particles of the alloying element distributed throughout, but most profusely near the metal surface (see Fig. 2, top). Where this type of structure obtains, the process of oxidation is believed to be implemented, and its rate controlled, by the diffusion of the reacting elements through a' continuous matrix phase; i.e., through the alpha (metallic) phase of the subscale and alloy and through the cuprous oxide of the external scale. Copper is presumed to diffuse outward through the cuprous oxide layer to the external surface, where it reacts to form more cuprous oxide.3 Oxygen is delivered at the oxide-metal interface in the form of cuprous oxide, which may either react with the alloying element to deposit its oxide at the inner limit of the external scale or dissolve in the pure copper that remains at the surface of the metal after it has become depleted in its oxidiza-ble alloying elements. Both oxygen and the alloying element are pictured as diffusing through the metal, the oxygen inward and the alloying element outward. Where the two diffusion streams meet in sufficient concentration the oxide of the subscale is precipitated. If the oxygen pressure in the surrounding atmosphere is just below the pressure necessary to maintain cuprous oxide undecomposed, no cuprous oxide can be formed; some of the oxide of the alloying element may form upon the external surface, if its decomposition pressure is below that of cuprous oxide, and a normal sub-scale appears. This condition is achieved experimentally by enclosing the alloy with cuprous oxide together with an excess of copper. At temperatures from 600°C. downward, the precipitated oxides tend to accumulate at the grain boundaries of the alpha phase where a relatively small volume establishes a partial barrier to the diffusion of the reactants- Similarly, large volumes of Precipitated oxides tend to deposit in various patterns that may be expected to

Jan 1, 1944

By F. N. Rhinos, B. J. Nelson

Studies upon the rates of oxidation of copper alloys containing small quantities of the alloying elementsl,2 have shown that steady growth of the scales at predictable rates is limited to a small concentration range and to oxidation at temperatures above 600°C., whereas unpredictable and erratic oxidation behavior is found with alloys containing larger additions and at low temperatures. The latter effect appears to be associated with modifications in the geometric disposition of the oxides. At low concentrations of the baser elements in copper, simple oxidation behavior is typified by the formation of two distinguishable zones of oxidation: (I) a subscale composed of discrete particles of the oxide of the alloying element embedded in substantially pure copper and (2) an external scale composed of cuprous oxide (with a very thin layer of cupric oxide on the outside) containing particles of the alloying element distributed throughout, but most profusely near the metal surface (see Fig. 2, top). Where this type of structure obtains, the process of oxidation is believed to be implemented, and its rate controlled, by the diffusion of the reacting elements through a' continuous matrix phase; i.e., through the alpha (metallic) phase of the subscale and alloy and through the cuprous oxide of the external scale. Copper is presumed to diffuse outward through the cuprous oxide layer to the external surface, where it reacts to form more cuprous oxide.3 Oxygen is delivered at the oxide-metal interface in the form of cuprous oxide, which may either react with the alloying element to deposit its oxide at the inner limit of the external scale or dissolve in the pure copper that remains at the surface of the metal after it has become depleted in its oxidiza-ble alloying elements. Both oxygen and the alloying element are pictured as diffusing through the metal, the oxygen inward and the alloying element outward. Where the two diffusion streams meet in sufficient concentration the oxide of the subscale is precipitated. If the oxygen pressure in the surrounding atmosphere is just below the pressure necessary to maintain cuprous oxide undecomposed, no cuprous oxide can be formed; some of the oxide of the alloying element may form upon the external surface, if its decomposition pressure is below that of cuprous oxide, and a normal sub-scale appears. This condition is achieved experimentally by enclosing the alloy with cuprous oxide together with an excess of copper. At temperatures from 600°C. downward, the precipitated oxides tend to accumulate at the grain boundaries of the alpha phase where a relatively small volume establishes a partial barrier to the diffusion of the reactants- Similarly, large volumes of Precipitated oxides tend to deposit in various patterns that may be expected to

Jan 1, 1944

By A. Singh, R. D. Govender

The current method employed to quantify the efficiency of separation of ferromagnetic ores by wet low intensity magnetic drum separators (WLIMS) incorporates the use of a conventional benchscale Davis Tube (DT) operating at a magnetic field intensity that is equivalent to that of the drum’s surface. However, empirical research has indicated that the magnetic force, or force index, rather than the magnetic field intensity, is the critical factor in the operation of the magnetic separator (Murariu and Svoboda, 2002). Furthermore, the current aforementioned practice would yield incorrect information as the magnetic field gradients produced by a typical WLIMS unit differs considerably from that of a bench-scale DT. In light of this, research on magnetite focusing primarily on the scale-up of DT results to pilotscale WLIMS were undertaken. The investigation entailed a comparative study between that of a typical WLIMS circuit and a bench-scale DT. The purpose was to practically evaluate the performance of a WLIMS, bench-marked against the traditional laboratory-scale DT unit. Moreover, the secondary objective was to produce a magnetite concentrate graded at 69% Fe, 95% -45μm, as a suitable source of separation media for use in the Dense Medium Separation (DMS) industry. Fundamental findings of previous works provided a framework for the study, however, a realworld approach was explored. Preliminary testwork conducted at Mintek investigated the performance of a DT and a typical multi-stage laboratory-scale WLIMS circuit (operating at 1000 Gauss at the surface). The results attained indicated that a DT operating at high intensities is comparable to a single rougher WLIMS stage. Additionally, it was observed that the three stage laboratory-scale WLIMS circuit performed similarly to the DT operating at 1000 Gauss. Moreover, piloting testwork was undertaken, carried out in larger 380mm drums, and the results attained showed a strong correlation with laboratory-scale findings. Keywords: Davis Tube, wet low intensity magnetic separation, magnetite

Jan 1, 2020

By J Say, M Hawtin, L Carlon, P Cann

Historically, production from sublevels of the Ernest Henry Mine (EHM) started from blind uphole rises at the end of slot drives. Where previous investigations considered removing these slot drives and starting production with independent ore drives, any development savings were consumed when drives were extended to minimise ore loss. Since 2017, EHM and Orica have been investigating opportunities to optimise drill and blast practices by implementing Orica’s Wireless Electronic Blasting System (WEBS). To reduce ore drive development metres, a novel design was proposed utilising the WebGen™ 100 system to combine a rise with pre-charged widening firings. Initially these new rise and widening firings achieved results similar to previous EHM designs, achieving on average 81 per cent of design height and width. Due to poor performance of the fourth trial a significant re-design was required. Modifications included drill hole re-positioning, in-hole primer relocation and initiation delay adjustments. Since the re-design a step change in rise performance has been observed with rise and pre-charged widening shots averaging 95 per cent of design height and width. With rise and widening performance exceeding expectations, the removal of slot drives has allowed a substantial reduction in lateral development. Development savings of 165 m and 169 m from the RL1325 and RL1300 levels have been achieved. Primary draw and ore recovery has also increased due to the later addition of pre charged forward stripping rings. Level design changes have also significantly improved the mining cycle by allowing for a reduction in required ground support, improved secondary ventilation, a reduction of critical path development, simpler production scheduling and less wear and tear on machinery. Future mine level designs now incorporate key learnings and are proving beneficial to a variety of scenarios including changing orebody boundaries at depth.

Mar 15, 2021

By G Senanayake, K Hazarika

The demand for iron-ore is ever increasing with the industry directly employing 60 500 people in a range of highly skilled roles in Australia. In the year 2019, the global iron-ore production was 2.85 billion tonnes. It is estimated that each tonne of beneficiated iron ore produces 400 kg of tailings. The IOTs are fine, dense and stable crystalline material mainly composed of iron oxides, alumina and silica. The current and most applied method of iron-ore tailings (IOTs) disposal is using subaqueous disposal of tailings in dams. The footprint generated by a tailings dam is massive and requires constant monitoring due to the possibility of a failure making the operation and maintenance of tailings dam extremely expensive. This review briefly discusses the known causes of tailings dam failures, their impact to the environment and day-to-day human life and potential applications of IOTs. The increase in water content enhances the pressure on dam walls. This in turn increases the liquefaction potential of the tailings and reduces the overall strength of the dam making it more vulnerable to failure. Potential applications of IOTs are in paints, aggregates in construction materials and bricks. The reuse of IOTs reduce waste and generates further revenue facilitating a path towards a sustainable future for the industry.

Nov 8, 2021

By F. C. Noyes

DAME Nature was in a generous mood when she distributed widely over the face of the globe numerous deposits of phosphate rock from which man can make phosphatic festiIizer to replace the phosphate re- moved from the soil by crops. The principal deposits are readily accessible to the world's greatest consuming areas and most of them are such that mining operations can be carried on at relatively low cost. The world's known reserves shown in Table 1 are sufficient to last well over 2000 gears at the present rate of consumption. Before giving a brief outline of the phosphate rock industry of foreign countries let us try to get a picture of the movement of phosphate rock throughout the world in 1938, the last full normal calendar year where it came from and where it was consumed. Table 2 shows the origin and finial destination of world shipments in 1938 by grand divisions. Table 3 (p. 499) shows shipment9 of phosphte rock to each country in Europe. Europe is seen to be by far the world's greatest market and the French North African mines the world's most important producers outside of the U. S. A.

Jan 1, 1944

By W. Griffith

"While oxalic acid precipitation practices are commonly applied on purified rare earth elements (REEs) pregnant leaching solutions (PLS), few efforts have been reported using oxalic acid (OXA) to recover REEs directly from untreated PLS. High oxalic acid demand is the most significant issue in all these direct oxalic precipitation (DOP) practices. Preliminary research on DOP of REE from a dilute PLS originating from an acid bake followed by water leaching was conducted. At 75°C, the oxalic acid demand was between 12 and 18 times the stoichiometric requirement for complete REE precipitation. Conducting DOP at 25°C had superior REE recovery but the product purity and filterability declined. Between 75°C and 100°C, REE recovery increased with increasing temperature. When sodium hydroxide was used to adjust the pH during DOP, in the range of 0.5 to 1.5, higher pH benefited REE recovery. Using ammonium hydroxide in place of sodium hydroxide, the REE recovery was reduced by close to 5%. Sodium chloride addition to the PLS was also investigated and the results showed that at both 75°C and 25°C, the REE recovery was enhanced substantially. At 25°C, when the oxalic acid addition was controlled at 4.7 times the stoichiometric requirement, the overall REE recovery reached 95% with the addition of 240 g/L NaCl. Other reagents such as KCl, NH4Cl also showed significant enhanced REE recovery at the same oxalic acid addition. The addition of sodium sulphate appeared to largely enhance the precipitation of LREE but inhibited the formation of HREE oxalate. All results indicate the formation of rare earth double salts may play an important role in REE DOP sulphate media.INTRODUCTIONThe conventional routes for recovering rare earth elements (REEs) from a sulphuric acid pregnant leaching solution (PLS) involves an initial purification step for removal of iron, aluminium for example by precipitation through neutralization, followed by precipitation of REEs as hydroxide, oxalate or carbonate salts, or by bulk solvent extraction for REE recovery (Xia, 2013). Another route was used by Bayan Obo in their historical flowsheet, where the PLS was first subjected to double sulphate precipitation, then the remaining REEs, mostly heavy rare earth elements (HREE), were recovered by oxalate precipitation (Li, 2011)."

Jan 1, 2016

By A. W. Gauger

DESPITE many handicaps and in the face of many discouragements anthracite and bituminous coal producers continue to supply the needs of the nation now vastly multiplied by the demands of the greatest war of all time, total output being about 620,000,000 tons of bituminous and 64,445,000 of anthracite. The progress made by this industry during the national emergency reflects more credit on all connected therewith than will ever be given. Not only has the industry been called upon to produce more coal than ever before but it has also sent representatives to England to study and advise on methods for increasing production there, and has co-operated with other Allied Nations by welcoming engineers sent to this country to study American practice. One noteworthy development has been the growth of strip mining in the

Jan 1, 1945

"Far from being eclipsed by petroleum and natural gas, Canadian coal continues to command wide (and apparently growing) interest.Major R & D investigations are currently heavily oriented toward coal beneficiation (e.g., cleaning and utilization of fines) and toward a broad range of studies on metallurgical coals and cokes. However, active work is also being carried out in the areas of coal geology, mining, transportation and combustion; and, in some laboratories, increasing stress has been laid on developing a number of new, essentially non-fuel uses for coal and coal products.This review summarizes the work of Canadian coal research agencies during 1966 and indicates some of the more important advances made by them."

Jan 1, 1967

"Conveyed coal flows have been diverted on the basis of real time ash analysis since the 1980s. Many coarse particle separation methods are available through screens, jigs, heavy media separation, particle sorters, to name a few, however bulk diversion requires a representative, continuous analysis to ensure diversion decisions can be made with confidence. Sensors also need to be able to provide measurements at useful time increments so that small tonnages can be diverted for maximum selectivity. Particle separation typically requires high capital costs and there are limitations either in throughput tonnage or particle size or both. Few techniques are able to provide robust and representative analysis of conveyed flows in a useful time basis. Prompt Gamma Neutron Activation Analysis provides multi-elemental analysis of conveyed bulk materials and has been proven in the minerals industry since 2003. This paper outlines the success of this technology in minerals applications in iron ore, phosphate rock and most recently in copper-gold ores, including its use in bulk diversion.INTRODUCTION Naturally occurring quality variability, or heterogeneity, in mineral deposits enables separation and recovery of the valuable components through mining and processing operations. There are distinct advantages in processing the minimum quantity of material to achieve the highest possible yield. Unfortunately, declining ore grades has resulted in larger scale operations and a subsequent loss in selectivity for mining operations. As limits are approached on the practical size of equipment, there is more motivation to investigate alternative solutions. Mining companies are subject to increasing social resistance to growing waste disposal requirements in addition to higher energy and transport costs. Major savings are available by reducing the quantities of material processed where pre-concentration can be effectively applied at early stages in the process. One of the simplest ways to pre-concentrate is to measure the bulk material and reject waste soon after mining so that minimal expense is incurred and that only higher quality material is sent to processing operations. This bulk sorting can occur within the mining operations and has major benefits through energy and other consumables savings. This paper discusses the application of real time analysis technologies suitable for bulk sorting within the minerals industry. Technology that has proven representative for conveyed material bulk analysis and its successful applications to date is explained. Analysis using a sensing technique is only one component of a successful bulk sorting process; the importance of effective diversion systems and a bulk sorting strategy are also discussed. The bulk sorting stage may be one component of a system that could include additional downstream technologies such as particle based sorting systems on a diverted stream."

Jan 1, 2018

By R. J. Leary

The natural gas-air burner described in this report was designed and constructed to meet the thermal requirements of a convective process for heating steel scrap. This process involved downward combustion of natural gas with air, blending the combustion products with diluent air, and then passing this tempered stream of gases downward through a porous bed of steel scrap contained in the furnace chamber. The scrap would be heated to a temperature limited by the adiabatic flame temperature of the gas stream in a period that depended on the rate at which heat was supplied per unit of bed cross section. The temperature of the gas stream would be limited to that beyond which an objectionable degree of oxidation would occur; for carbon steel this limit had been found to vary from 1,900° to 2,100° F. with the superficial velocity of the gas stream. The productivity of the process was dependent on the rate of heat input per unit of furnace cross section; for the 3-foot-diameter experimental furnace an input of 680,000 B.t.u. per hour was desired. The burner described was designed to meet these conditions of temperature and heat input. It provided for three streams of entering gases: (1) A primary air-fuel mixture too rich to be combustible, that is, above the upper flammable limit; (2) secondary air for combustion of the primary mixture; and (3) tertiary air, principally for cooling the combustion products to the temperatures desired for process operation. Downward combustion of the primary and secondary streams occurred in a flame stabilized on an annular port, while tertiary air flowed in an annular path surrounding the port and also through an axial channel whose wall formed the inner ring of the annular port. This burner performed beyond the designed heat-input rates while producing stable flames, which were adjusted readily to the temperatures desired. Gas-stream temperatures were easily controlled to within 15° F. of the desired value by simple manual adjustment of the flow valves.

Jan 1, 1959

By G. J. Hundman

Control of respirable dust produced by auger type continuous mining machines is normally attempted by water sprays from fixed nozzles mounted on the frame of the machine. In tests conducted under this contract, a 'wet auger' system was used, where the spray nozzles were mounted on the rotating auger itself. The tests were conducted at the Hunter mine of Smith and Stover Coal Company using a Jeffrey 1.00L auger miner. Operating the mining machine in the wet auger mode, it was found to produce 47 pct less respirable dust than when the fixed conventional sprays were used. On section dust levels were reduced too 3.5 mg/m3 which is equivalent to approximately 2.0 mg/m3 for a full shift portal to portal sample. The major difficulty that had to be overcome was the development of a simple reliable water transfer mechanism to get the water into the rotating augers. This was successfully achieved by the development of a water-through-the-shaft water system. This system can be retrofitted to existing machines and is available in kit form.

Jan 1, 1977