Search Documents

By L. C. IlsLey, J. W. Paul, E. J. Gleim

Flame safety lamps have been used in gaseous mines since the Davy lamp was introduced, more than 100 years ago. During the last decade the flame safety lamp has been rapidly replaced by the electric lamp as a device for illuminating the miner's working place; in the United States the electric cap lamp has been widely adopted. For example, in 1911 approximately 45,000 flame lamps and no electric lamps were being used in the Pennsylvania bituminous mines, which were then producing 35 per cent of all the soft coal mined in this country; by 1918 the flame lamps had decreased to 17,000, whereas electric lamps-mostly of one maketotaled nearly 48,000. In Great Britain during the same years the total of 723,934 flame lamps decreased to 590,185 and the electric lamps gained rapidly from 4,298 to 156,521. No later reliable figures are at hand. However, before the flame lamp becomes obsolete, it is fitting that the Bureau of Mines compile a permanent record of a device which has served the mining industry for more than three generations, and not only made possible the development of entire districts that otherwise could not have been worked but undoubtedly saved the lives of thousands of underground workers. Flame safety lamps are capable of doing more than the name indicates. First, under normal conditions, they can be used in a mine atmosphere that contains an explosive mixture of gas and air without great danger of exploding such a mixture, though such use of a flame lamp should not be permitted. Second, to an experienced man they indicate percentages of gas much lower than the explosive limit, and thus can be used to indicate to workers the approach of an unsafe condition in the mine atmosphere. Third, flame lamps will not burn in an atmosphere greatly deficient in oxygen, and they therefore warn the users of such deficiency in time to withdraw to a place of safety. Flame safety lamps are still used rather widely in the United States for general illumination and to a still greater extent for detecting gas. Many coal-producing States require fire bosses to use these lamps in gaseous mines, and the regulations of several States specify that a gIven number of such lamps be kept available for emergency service.

Jan 1, 1924

By Yemi Akinkugbe

Underground coal mining under massive sandstone can present significant challenges if the roof behavior is not well understood. This paper presents a classic cantilever bending/flexing behavior of a longwall tailgate roof caused by the weighting of structurally massive sandstone strata. Nineteen crosscuts of a longwall tailgate under massive sandstone were instrumented with position transducers connected to a data-logger to monitor roof convergence as the longwall face approached. During the monitoring program, an unusual tailgate roof divergence (uplift) was recorded. This roof behavior contradicts expected norm of roof convergence when the longwall is influenced by periodic weighting. The recorded roof movement data indicated that the roof divergence started well ahead of the longwall face. The most inby position transducer started recording progressive roof divergence when the longwall face was approximately 643 feet away. Very gradual roof convergence did not begin until the longwall face got to within 300 feet of the transducer. Recording of accelerated convergence only started after a massive caving event with the face within 280 feet of the recording transducer.

Jan 1, 2007

By A. Rios

ENAMl's Paipote Smelter commenced operations in 1951. At present, it processes 230,000 tonnes/year of green feed in a conventional smelter, which comprises one reverberatory furnace, two Hoboken, one Peirce-Smith converters and one rotary anode furnace. The feed is composed of 83% copper concentrate and 17% metallic copper precipitates, which results in a feed average grade of 32% of copper content. The final products are 75,000 tonnes/year of copper anodes and 48,000 tonnes/year of sulphuric acid. At present, the plant is undergoing a modernization to expand the smelter capacity to 300,000 tonnes/year of green feed and increase the sulphuric acid production to 100,000 tonnes/year. This will be achieved with the installation of an El Teniente Converter and an expansion in the acid plant. The work began in November 1991 and is scheduled to be in operaton by March 1993. The paper provides an overview of the modernization plans and results achieved to-date.

Jan 1, 1993

By K Ehrig

You are a geologist, geometallurgist, or metallurgist/process engineer and are fortunate enough to work for an organisation who asks you to design/execute a geometallurgy program. What seems like a simple request is actually not a trivial exercise. æRecipeÆ style manuals are not readily available. However, many æexpertsÆ are lurking around willing to deliver solutions which will solve all of your problems. Even though similar ore deposit styles (e.g. porphyry Cu, IOCG, Ni-laterites, calcrete hosted U, etc.) have many similar characteristics, each ore deposit is unique. Hence your geometallurgy program needs to be æfit-for-purposeÆ. This paper offers some insights gained via designing and executing geometallurgy programs from exploration through to production, and working at a mine where you are held accountable for your metallurgical performance predictors.CITATION:Ehrig, K, 2013. Geometallurgy - What do you really need to know from exploration through to production?, in Proceedings MetPlant 2013 , pp 28-33 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Michael Hood

High-volume, low-pressure water jets have been employed for erosion of loosely consolidated rocks for centuries. This excavation method finds application in specialized circumstances even today. The use of high-pressure, low-volume water jets for rock cutting is more recent and was made possible by the development of high-pressure water pumps. Despite the benefits often claimed for these systems, high-pressure water jets still have not found widespread application. In this report, the U.S. Bureau of Mines has reviewed the various methods that have been employed using water jets to break rock and has focused on one method, termed "jet-assisted cutting," which was determined to be the closest to commercial development. The current state of knowledge based on laboratory and field experiences using this cutting method is reviewed, and possible future developments for this approach to excavation are assessed.

Jan 1, 1990

By D. R. Pyke

Many of the gold deposits in the Timmins• area show a close spatial association to ultramafic metavolcanics. Available analytical data suggest that ultramafic rocks contain significantly higher gold contents than other major rock types. In addition, recent analyses by Keays (1975) suggest that talc-carbonate alteration of ultramafic rocks releases significant quantities of gold. It is proposed that the ultramafic volcanics formed the principal source of gold for the deposits in Timmins, and that the gold was derived from the ultramafic flows when they were extensively carbonatized. Carbonatization of the ultramafic rocks and emplacement of the auriferous quartz-carbonate veins was probably coincident with the last major period of deformation in the gold camp. Delineation of hitherto unrecognized ultramafic volcanics could be an important guide to the discovery of further gold deposits.

Jan 1, 1976

By S. K. R. Iyengar

This report presents the results of a study to develop optimal designs for light-weight mine roof supports for use in underground coal mines. A load capacity of 196 kN (22 tons) and a height adjustable between 1.829 m (72 inches) and 2.438 m (96 inches) were taken as the design parameters and the design goal was a unit weighing less than 22.3 kg (50 lbs). Three alternative design concepts were explored, viz. mechanical, hydraulic, and hydro-mechanical and a total of 13 designs analyzed in detail. Steel, aluminum alloy and composites were the main potential construction materials investigated for suitability from structural, life, and safety and other considerations. The designs considered most promising for development were: (i) the mechanical screw-pin type using telescopic tubes and a fine adjustment screw thread section (ii) the all-hydraulic type, of steel, aluminum alloy or aramid graphite construction (iii) the hydro-mechanical design using telescopic tubes and a short stroke hydraulic cylinder for fine adjustment It is shown that by using realistic mathematical models for stress and deflection calculations, it is possible to reduce prop weight to the design goal. The analysis presented for all-hydraulic props is applicable to hydraulic cylinders on all mining equipment and similar machinery. This report includes the computer program and user's guide for analyzing hydraulic cylinders as well as a cross-indexed bibliography on structural composites.

Jan 1, 1978

By K. L. Paciorek

The primary objective of this program was to determine the toxic fume and fire hazard of elastomeric noise abatement materials with a limited effort expended on the evaluation of specific treatments applied to mine timbers. Under the conditions employed, for a dimethyl silicone rubber, formaldehyde presented the major toxic threat; acrolein was the main toxic species for both polyester and polyether urethanes and an acrylonitrile-butadiene-styrene resin; in the case of flame-retardant styrene-butadiene rubber compositions, hydrogen chloride, and in the case of PFA-treated timber, furfural, were the major toxic compounds. Of the materials studied, the flame-retardant styrene-butadiene rubbers presented the greatest toxic hazard. The generated data have been reduced to toxic load tabulations amenable to employment for potential hazard assessment.

Jan 1, 1982

By Rob Boom, Yasuyuki Tozaki, Greg Traquair

The objectives of the business case are to examine a proposed metallurgical project and answer fundamental questions about project feasibility, risks, opportunities, and value. A business case fulfills these basic functions: estimates economic value; helps to understand competitiveness; serves as a risk management tool; and serves as a communication tool. A business case evolves with the project life cycle, and supports the gate reviews at the end of each phase of engineering, through to project construction and operations. A business case must be holistic, including all elements of scope that can impinge on project risk and value.

Jan 1, 2015

By F. Khorram

Image processing is a technique that simulates the human vision system. This technique enables applying every statistical or intelligent operation to recognize differences. In this way this new technique is used in quality control systems in most industries. Studying sedimentary rocks is very important from the economic point of view. Some units of sedimentary sequences involve different mineral deposits, hydrocarbon and water resources. Therefore it is important to identify and classify different sedimentary rocks. Descriptive classification of sedimentary rocks is usually based on visual and textural features and chemical composition of a sample. In this paper different samples of a limestone mine in central part of Iran are classified. The samples were collected from different parts of the mine and crushed down in size from 2.58 cm to 3.58 cm. The rock samples were labeled based on percentage of chemical and lithological compositions. Each sample was assigned to one of the distinguished groups. The images of the samples were taken in appropriate environment and processed. A total of 74 features were extracted from the identified rock samples in all images. In order to feature dimensional decrease, principal component analysis method was used. Then Bayesian statistical algorithm was used as a useful tool for classification. Classification Correctness Rate (CCR), calculated for the test data sets are %88, %68, %61 and %72 for the first to fourth class respectively. Therefore it can be inferred that the extracted features of images are appropriate indicators for different samples identification. These precise results besides the advantages of image processing technique, which are increasing speed of operation and decreasing cost, appears to be a desirable success.

Jan 1, 2012

By R. E. Moore

Refractories are unique ceramic materials, which are used in large quantities in steel making furnaces, metal smelting vessels, and glass melting tanks. They are required to possess high thermal shock properties and good slag corrosion resistance as well as creep resistance at high temperatures. Therefore, they are made from very refractory minerals such as lime, periclase, corundum, spinel, and zirconia. Slags are vitreous materials produced as a residue in steel refining processes. They cover a wide range of compositions and may contain pure oxides, silicates, and sulfides as well as fluoride phases depending on the melting and smelting processes. These minerals exhibit spectacular cathodoluminescence color under electron bombardment; therefore, cathodoluminescence (CL) microscopy is found to be a superior technique for the characterization of refractory corrosion by slags. Examples included in this study are (1) reaction of fluorine containing mold slags with ZrO2-C nozzle refractories promoting crystallization of the Cuspidine, Ca4Si2O7(F,OH)2, (2) corrosion of fusion cast refractories in TV panel glassmaking furnaces and formation of glass defects, and (3) reaction of spinel based castable refractories with copper smelting slags.

Jan 1, 2001

By Brian Fulcher, Michael Bell, Shimi Tzobery, Werner Burger, John Bednarski

The Arrowhead Tunnels Project represents the final portion of a 70 km (44-mile) long water conveyance facility that will bring up to 28 m3/sec (1,000 ft3/sec) of water into Southern California. The 13 km (8-mile) tunneling project is well underway and consists of two, 5.8 m (19-foot) diameter TBM bores through extremely variable geological conditions. The tunnels lie near the base of the San Bernardino Mountains and several significant faults including the San Andreas Fault run within one kilometer (0.6 miles) of the tunnel alignment. Numerous other significant faults cross the tunnel alignment and water pressures in the tunnel have been recorded as high as 20 bar (300 psi). This paper describes some of the problems and challenges encountered and the solutions implemented to advance the two hybrid TBMs under conditions that ranged from hard rock with no water inflows to full-face granular material under 10-bar pressure and in excess of 32 l/sec (500 gpm) inflows. Due to the range and severity of ground and water conditions actually encountered, the Owner-Contractor-Designer team eventually found that adjusting the means and methods to be more responsive—virtually on a day-by-day basis—was needed to suit the conditions

Jan 1, 2007

By Wern-Ping Nick Chen

Durability risks for underground facilities can be underestimated during design phase as compared to well-known geological risks. However, unclear durability requirements can result in construction schedule delay and change orders. Unlike bridges or buildings, a unified underground durability code or standard does not exist. This paper will provide a durability approach for underground facilities, including degradation modes, mitigations, and compliance measures during construction. In addition, this paper will address how to clearly specify durability requirements in a contract document to reduce disputes during construction and discuss key durability tests that are time consuming and will impact construction schedule if not timely planned.

Jun 23, 2024

By Arthur A. F, MacKenzie I. H

Copper in zinc/lead sinter charged to the Imperial Smelting Furnace operated by Sulphide Corporation Pty Limited at Cockle Creek, New South Wales, concentrates in a complex lead dross which forms as the bullion is cooled to around 400°C. The 0.35 mm portion of this dross, containing approximatelY 67 per cent of the total copper, is treated via a hydrometallurgical route to produce 5000 tonne/yr of CuSO4 5H2O crystal.Around 3000 tonne/yr of copper-lead dross containing 49 per cent copper is leached at 55°C in continuous leach reactors with ammoniacal ammonium carbonate leach liquors to convert copper to soluble copper amine complexes. Leach ettlciencies of 80-85 per cent are obtained. Leach residues are repulped with ammoniacal liquid diluents from the plant and heated in a four stage steam distillation unit to reduce ammonia levels to between 0.5 and 1.0 g/Iitre. The resultant slurry is directed to an effluent treatment plant for final treatment, and separation and return of solids to the sinter plant.Copper is extracted from leach liquor by solvent extraction techniques based on the use of L1X 54 diluted 3:1 with Shellsol 2046 to give a nominal copper loading of 30 g/litre. The loaded organic is contacted with a sulfuric acid solution of pH 5 to remove the bulk of ammonia and zinc, then stripped at 55°C with a 60 g/Iitre H2SO4 95 g/Iitre copper solution to yield a 15 g/Iitre H2SO4 125 g/Iitre copper solution.This liquor is fed to an adiabatic vacuum crvstalliser operating at 35°C and 5 kPa vacuum where crystals of CuSO4 5H2O are formed. Crystals are separated from mother liquor and washed in a two stage pusher centrifuge, then dried in a hot air rotary drier. The crystal product obtained is of a high chemical purity and readily conforms to both Australian and overseas standards.

Jan 1, 1983

By M. van Elp, R. Saitua Nistal, P. J. M. Groot

Demand for construction raw materials depends on investment in housing, other buildings and infrastructure. The provision of these materials requires early knowledge of future trends in construction investment. By using scenarios possible future developments and bandwidths can be explored. Policy makers in government organisations as well as in the private sector can base their policy decisions upon these insights. In this paper we discuss the case of sand and gravel in the Netherlands. We will show that, depending on the future role of government and the degree of internationalisation, the long term demand for construction raw materials will strongly diverge. Nevertheless there are some common developments such as a decreasing population growth, a smaller share of the labour force in total population and a growing wealth. In different scenarios we will encounter different conditions for minerals provision and for sustainable development.

Jan 1, 2011

By R. W. Watson

In January 1980, the Bureau of Mines initiated an experimental program to examine the fire and explosion hazards of one-hour self-contained self rescuers (SSRs). This action was prompted by a growing concern on the part of government and industrial safety officials over the potential hazards of these devices when deployed on a large scale in underground coal mines. Prior evaluation of the safety of these devices had been at best sporadic and usually limited to experimental models. The recent availability of preproduction models of a l-hour SSR fabricated by the Mine Safety Appliance Company* and a production model manufactured by Dragerwerk Ag Lubeck of the Federal Republic of Germany allowed for a more comprehensive and meaningful evaluation of their safety in underground coal mines. This report summarizes the results of a 5-month study of the potential hazards of these two items. During the course of the work, periodic progress reports were presented to officials of the Mine Safety and Health Administration and various mining organizations including the American Mining Congress, Bituminous Coal Operators of America. National Independent Coal Operators Association, and the United Mine Workers of America. The free exchange of ideas that occurred during these meetings had a significant impact on the direction of this study and a serious attempt was made to address all of the issues that were raised at these meetings. The authors are extremely grateful to the individuals that participated in defining the specific problems that could arise as a result of deploying the self-contained self rescuers in an underground coal mine environment.

Jan 1, 1980

By Gaom M. W.

The Mount Isa copper concentrator started operation in 1973. Its secondary grinding circuit consisted of two 5 meters diameter ball mills in closed circuit with 505 mm cyclones. At the design throughput of 800 t/h, the 80% passing size of the circuit product (P80) was about 140 µm. The then Mount Isa Mines Limited (?MIM?) installed two autogenous grinding (?AG?) mills in 1991 to replace two stages of crushing, a rod milling stage and one primary ball milling stage. One of the AG mills was later converted to semi-autogenous grinding (?SAG?) operation by the addition of a steel grinding medium to achieve the designed plant throughput of 800 t/h. The cyclone over-flow P80of the secondary ball mill circuit was reduced to 120 µm by the increased operating power in the AG/SAG mill circuits. The two secondary balls mills had a grinding power of 5.2 MW. A mineralogical study of the milled products indicated that half of this grinding power was sufficient for adequate chalcopyrite liberation. Eliminating one of the secondary ball mills could reduce energy and operating costs by more than A$2 million dollars per year. An optimisation project team was established to achieve the predicted power saving. Grinding circuit simulations were conducted for different circuit configurations. Ball mill parameters such as ball size, ball charge and feed slurry density were optimised. Cyclone body diameter, spigot and vortex finder sizes, and cyclone types were tested. The secondary ball mill circuit was redesigned and several proposed circuits were run as trial production campaigns to determine their operability and efficiency. The plant trials confirmed that one of the secondary ball mills could be decommissioned. Significant cost savings were achieved as a result. The success of the project demonstrates optimising grinding circuits can not only deliver the plant performance, but also a much lower unit operating cost through energy and maintenance savings.

Jan 1, 2014

By Jeffery L. Kohler

This final report on Bureau of Mines Contract J0338028 presents the results of a research effort to predict incipient failure in electric-power-system components. The development of continuous monitoring techniques to detect an incipient failure would represent a significant improvement in system maintainability, availability and safety, This report describes the analytical and experimental aspects of the project. Mathematical models have been developed to study the behavior of cables and motors which are undergoing a deterioration process. These models allow a detailed study of the effect of deterioration on the component's terminal characteristics and performance. The efficacy of using negative-sequence monitoring is a reliable indication of deterioration has been established. Techniques for assessing the sensitivity of the prediction algorithm to component deterioration have been presented. An approach for modelling electrically-excited vibrations, and including these in the algorithm, has been presented.

Jan 1, 1987

By Will H. Coghill, Fred D. DeVaney, R. S. Dean

Part I CONTENTS

May 1, 1934

By J. D. Patsey, G. T. Lineberry

Introduction A computer program was developed for analyzing drum-type hoists before modifying an existing system or designing a new one. Its use permits the preliminary evaluation of a system before seeking technical assistance from mine hoist designers and manufacturers. The user-friendly program accepts a variety of data and analyzes hoisting systems for any balance state. The program can be used to calculate skip capacity to yield a desired production rate, solve for drum face width, select a permissible wire rope, estimate total horsepower of the hoist plant, and estimate annual power cost. Whether required for a large mining complex or for a relatively small operation, a hoisting system must be carefully designed to ensure the efficient, reliable, and safe flow of material. Because shaft sinking and hoist installation can total between 2.5% and 3% of the cost of opening a deep mine, proper hoist selection is critical. Today's mining engineer has at his disposal the most powerful design and analytical aid ever, the microcomputer. There is, unfortunately, limited software for the study of hoisting systems, unlike that for other materials handling equipment (Manula and Albert, 1980; Prelaz et al., 1964; Bucklen, 1969; Thompson, 1985). HOIST reduces a time-consuming set of calculations to a concise package of interrelated subprograms. A literature review revealed no common-user programs to analyze hoisting systems, although at least four major hoist designers/manufacturers/installers have their own in-house programs. To provide a tool with which the mining engineer could preliminarily analyze a materials hoisting system or could check the calculations of a hoist contractor, a computer program was developed. HOIST was written in BASIC for the IBM-PC for ease of program adaptation and to encourage field use on compatible systems. Details of program development are omitted, since the basic principles of hoisting analyses are relatively straightforward, simple, and readily accepted (Harmon, 1973; Nordberg, n.d.; Adler, 1957). Program features, intended usage, and benefits of the computerized solution are emphasized over theory development and mathematical rigor. Background The mine hoist system that is selected and installed at a mine is the "lifeline" of that mine, with installations lasting 20 years or more. Thorough study is warranted to ensure that productivity demands are met at a minimum cost per ton. The increased cost of a large, powerful, high-speed hoist must be offset by increased production to justify its selection. To optimize this tradeoff, an extensive hoisting analysis should be performed. The analyses to properly size the skip (or cage), the drum, and the hoist drive are conducive to computerization, permitting rapid evaluation of changeable operating and design parameters, such as velocity, acceleration, state of balance, and productivity demand. The program is particularly useful in conducting sensitivity trials, such as investigation into the effect of change of productivity on skip capacity and on horsepower of the hoist drive. HOIST is currently limited to the study of drum-type hoists with cylindrical drum(s). However, only minor changes to the program would permit analysis of friction hoists and conical drum configurations. Model development and testing The program is based on accepted equations and physical relationships. Examples of manual calculations formed the basis for decision points and program branching. Data is input in the order that it would be needed if the problems were solved manually. The choices are arranged likewise. HOIST was developed in sections, with manual solutions performed to check program logic. The testing became more rigorous as sections were completed. Output from one section becomes input for following sections, as appropriate. The simplified flow diagram of HOIST is given in Fig. 1.

Jan 2, 1987