Search Documents

By T. Cienski

The paper presents and discusses the results of a detailed study conducted on the subject of energy consumption in the comminution of industrial minerals. The study was based on pilot circuit testing, plant operating data collection, detailed equipment data and literature research. The areas covered by investigations include: high efficiency classification; air classifiers for cement grinding circuits; grinding aids in dry grinding: dry grinding circuit, control based on particle size measurement. Results obtained indicate a large potential for the reduction of energy consumption, in particular in the traditionally high cement clinker grinding circuits. Better classification techniques and correct application of grinding additives can significantly reduce power used per ton of product and also substantially increase grinding circuit output.

Jan 1, 1990

By Howard P. Hamlin

This Bureau of Mines report is concerned with the testing procedures for evaluating clays, shales, and slates for lightweight aggregates using the rotary-kiln method of production. To meet the increasing demand for light-weight concrete, rapid, accurate methods for appraising raw materials for light-weight aggregate are needed. Preliminary tests were made on samples of clay, shale, and slate, using laboratory equipment, and the data were used to establish operating conditions for pilot-plant-size rotary-kiln tests. Lightweight concrete was made from the processed aggregates and the properties determined. The results show that the laboratory data can be used to guide rotary-kiln testing, and, with the exception of sampling, a complete appraisal of a raw material for lightweight aggregate concrete can be made in 3 days by the methods described in this report.

Jan 1, 1962

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instruction3 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1969

By G. M. J. van Heerden, R. C. W. Webber-Youngman

"This article describes the re-engineering principles applied in the design of a personnel transportation system for the Bafokeng Rasimone Platinum Mine in the Rustenburg area of South Africa. It incorporates conveyor belt travelling, chairlift operation, and also includes consideration of proposed changes/modifications to the existing conveyor belt infrastructure.The purpose of the project was to identify, through a process of evaluation, the appropriate option and/or combination of transportation options that would be safe in terms of personnel transportation as well as cost-effective. Alternative measures for transporting personnel (not using belt riding) would have a significant positive spin-off, increasing the availability of the belt and thereby increasing production. This paper explores the feasibility of interventions that would improve safety through eliminating risk associated with personnel transportation as well as contributing towards improving the mine’s position on the cost curve.The design in consideration at the Bafokeng Rasimone Platinum Mine consists of two shaft systems, namely the North Shaft and South Shaft, each comprising twin decline shafts. One of the decline shafts is equipped with a conveyor belt for rock and personnel transportation, and the other with a winder for trackbound material transport. The conveyor belt has been used for personnel transportation since the commissioning of the shafts. The conveyor belt is equipped with platforms for personnel getting off and on the belt and a number of safety devices designed to ensure safety while travelling on the belt. Intensive training in the practical aspects of belt riding is given to every person, and unsupervised riding on the belt is permitted only once belt riding competence is demonstrated. Despite this, the safety results were poor, with 106 injuries between 2006 and May 2013. Fortunately, no fatalities were reported during this period.An investigation of alternative means for personnel transportation or engineered solutions to the current conveyor belt infrastructure in the safest, most effective, and most economical way was therefore needed. There was a major risk of safety-related stoppages being imposed following another belt accident/incident. This would prevent the mine from transporting personnel underground by belt and result in major production losses. From the commissioning of the Phase 2 shaft deepening project on both shafts, dedicated chairlifts have been used for personnel transportation as opposed to the conveyor belt installed in the Phase 1 area. The chairlifts have been in operation since 2004 and no chairlift-related incidents have been recorded thus far. According to safety statistics, it is clear that the chairlift is the safer method for the transportation of people in the shaft.To fulfil the objectives/scope of this study, it was recommended that both primary (new chairlift decline with infrastructure) and secondary options (modifications to the current conveyor belt infrastructure) be considered for implementation on both the North Shaft and South Shaft to reduce or eliminate accidents/incidents as a result of belt transportation. The associated capital expenditure would be approximately R200 million. Considering the future impact on the business as a whole, this would definitely be capital well spent."

Jan 1, 2016

By A D. Campbell

Sublevel caving (SLC) is a mining method adopted in a wide range of mining depths and ground conditions with various layouts adopted to suit orebody geometry. Sublevel caving offers more flexibility and versatility compared to other cave mining methods and is a low cost alternative to open stoping. SLC also has the advantage that stopes are not required to remain stable during production, and no backfill is required. This flexibility combined with increasing pressure on mines to target deeper and lower grade mineralisation has led to increased uptake of the method. The implementation of SLC mining methods across a wide range of mining depths and rock mass conditions has led to ground control practices which vary globally from mine to mine. To date, there has been limited documentation of ground control practices in SLC mining and few benchmarks available in the literature. This paper describes the main findings from a global benchmark of sublevel cave mines conducted over three years as part of the Caving 2040 research consortium. The purpose of the project was to document and compare operational practices, technical aspects and hazard management techniques across SLC mines around the world. The review included 21 mines spread over four continents and 17 different mining companies. This paper provides an overview of geotechnical conditions, challenges and ground control practices at each of the benchmarked SLC mines. Mine design and sequencing practices adopted for ground control purposes and hazard mitigation are provided with case studies. The impact of depth and rock mass conditions on mining productivity and development rates is also described.

Nov 29, 2022

This publication contains eight papers presented at a Bureau of Mines Technology Transfer Symposium in Charleston, W, on June 22, 1983, Five of the papers describe the results of Bureau-sponsored research on cabs and canopies for low-coal underground mining equipment. The other papers describe the efforts of three underground coal mining equipment manufacturers (FMC, Joy, and Lee-Norse) in the area of cab and canopy design.

Jan 1, 1985

By Michael Samis

The real option valuation method is often presented as an alternative to the conventional discounted cash flow (DCF) approach because it is able to recognize additional project value due to the presence of management flexibility. However, these two valuation methods can be separated on a more fundamental level by their differences in risk discounting. Real option valuation applies the risk-adjustment to the source of uncertainty in the cash flow while the DCF method adjusts for risk at the aggregate level of net cash flow. This seemingly small difference is the reason why the real option method is able to differentiate between projects according to each project?s unique risk characteristics while the conventional DCF approach cannot. This paper provides an overview of the real options and DCF valuation frameworks and discusses the differences in risk discounting that exist between the two methods. Using grade-school mathematics, this paper clearly demonstrates how, with real options, a unique project risk discount can be calculated which is directly linked to the project?s unique risk profile. It also highlights why the DCF method fails in this regard and shows why a call to ?increase the Risk-Adjusted Discount Rate? is an incomplete solution at best. Finally, a heap-leach project and satellite reserve development project are valued with both techniques and the difference in investment conclusions is explained in terms of the risk-discounting concepts discussed here.

May 1, 2003

By R. E. Morgan, D. L. Douglass

The determination of phase relationships and solid-solubility limits can be performed by quantitative metallography in addition to the usual X-ray and metallographic techniques. For example, Beck and smith1 redetermined the ß/ß + ?, ß + ?/?, a/a + ß and a + ß/ß boundaries in the Cu-Zn system by measuring the volume fraction of second phase of several alloys and extrapolating the volume fraction-composition curves to 0 and 100 pct. A modification of this technique is suggested for certain alloy systems, in which it is not necessary to use several alloy compositions but merely one. A single two-phase alloy may be used to determine terminal solubilities in the following manner. The method consists of equilibrating samples of the alloy in a two-phase region adjacent to the desired solid solution, at three or more temperatures, quenching, measuring the volume fraction of second phase present, and applying an analytical treatment to calculate the unknown solid solution. However, two restrictions are inherent in this technique. They are: 1) only certain types of alloy systems are amenable to it, and 2) the general features of the system must be known. The first drawback to the new technique, i.e., that only certain types of systems may be studied, necessitates that the composition at one end of the tieline must either be constant with temperature or well established as a function of temperature. Either a pure metal or some intermetallic compounds fulfill the former. If it is assumed that the volume per gram-atom of a dilute solution is unchanged by the addition of element B to element A, the composition of the solid solution in equilibrium with the second phase may be determined by a material balance and is given by where X, = volume fraction of B in a solid solution Xc = volume fraction of B in compound c X = volume fraction of B in alloy f = volume fraction of second phase The composition by weight may then be determined by the use of tables in the Metals Handbook2 when the density ratio of the solid solution constituents is known. A possible alternative treatment involving the use of the lever rule is less precise than the above tech- nique. This may be used when the density of the solid solution is either known or may be calculated from X-ray data for several compositions. The following analysis is then made. The ratio of compound to solid solution (by weight) may be expressed as follows: x0 - x wc = xr-x = x0 - x r2i Xc -X where Wc = weight of compound w = weight of solid solution x, - alloy composition, weight percent x = unknown composition Xe = compound composition but where V, = volume of compound VA = volume of solid solution pc = density of compound p, = density of solid solution fc = volume fraction of compound fB = volume fraction of solid solution and fs = l -fc then If pc and xc are known, and f, is measured, then pB is the only unknown on the right side of Eq. [4]. The known densities of the solid solution can be plotted for various compositions and can then be expressed mathematically as a function of composition. The use of an expression of pB = f(x)reduces the equation to one unknown—the desired solubility. In the event that the densities are unknown, they may be calculated for various compositions from Vegard&apos;s law. The calculated values are then plotted and expressed analytically. The most accurate results are obtained for Eq. [4] when fc<< 1, i.c., when (x, -x,) - 0, &/l-f, - m; but as fc/l -fc - 0, (xl-x,)- (x, - x), and x - x,,. However, the accuracy with which fc can be measured decreases as f, decreases.3 Alloys for investigation must be selected by a compromise, which is based upon an error analysis of Eq. [4] and knowledge of the accuracy of volume fraction measurements. An examination of phase diagrams in the literature showed many which were amenable to the technique described here. The zirconium-copper system was selected in order to determine the solubility of copper in beta zirconium. Pieces of an alloy which was arc-melted three times were wrapped in tantalum foil and sealed under an argon atmosphere in Vycor tubes. The sealed samples were equilibrated at temperatures from 850" to 960°C for 3 weeks and quenched to room temperature by smashing the capsule in water. Several planes of polish were examined, and

Jan 1, 1960

In the course of work being carried out in the Lubricants and Bearings Section of the Council lor Scientific and Industrial Research on the production of copper4ead &apos;bearings for &apos;use in aircraft, it has been found necessary to develop special metallographic methods. For proper control of the production of steel-backed copper-lead bearings it is necessary to adhere to rigidly controlled conditions, and it is essential that a method of examination be adopted which will readily detect actual defects or any variations in quality. Some defects can be observed with the naked eye, whilst others are detected by radiographic examination. This latter method is invaluable as a rapid, reliable test in the production of aircraft bearings, but it is necessary to observe the structure of the alloys under the microscope, both to be able to interpret the radiograph correctly and to determine what has occurred to the metal during and after solidification. The use of a sound metallographic technique is&apos;particularly important in developmental work and research connected with these bearings.Polishing TechniqueCopper and lead are practically immiscible in the solid state, but whilst they are miscible only in certain limited proportions in the liquid state; consequently &quot;alloys&quot; of copper and lead consist of a mixture of the constituent metals. The metallographic difficulties are obvious. Copper is a relatively tough metal, although it readily scratches, whilst lead is extremely soft and easily deformed. It wouId be expected if any normal polishing technique were applied that the lead would be readily torn out of the surface being prepared, and, in addition, that the lead would tarnish very easily.Grange(2) has described a method by which these difficulties can be overcome. The method involves an etch-polish procedure using &quot;chrome regia&quot; as an etchant for the copper. The chrome regia was a solution of chromium trioxide and hydrochloric acid in water. This type of etchant has been adopted, but it was found necessary to make certain changes.The method now adopted in this laboratory is as follows: The specimen (which is usually mounted in bakelite) is wet ground in a series of successively finer Hydro-Durexsil emery papers down to 60.0&#183; grit paper.The specimen is then etched in the chrome regis, etchant (the composition of this etchant will pe discussed later) for approximately five seconds.Most efficient etching is obtained by swabbing the surface of the specimen...

Jan 1, 1944

By D. J. Burdon, Anthony Caplan

"(1) The radiological appearances of pneumokoniosis on the Kolar Gold Field is described in detail. The characteristic abnormality is the. presence of a diffuse, fine annular and punctate mottling. (2) The frequency of symptoms could not be determined with any degree of accuracy, but it is believed that symptoms are absent and there is no incapacity until profuse radiological mottling is present, i.e., after long exposure to dust. (3) There is an increased predisposition to tuberculosis, which, if it occurs, affects the prognosismost unfavourably.(4) Pathological examination shows that the radiological mottling is due to the presence inthe lung of numerous small dust-cdll aggregates (up to T5 mm. in dia.) deposited around the smaller bronchioles and blood-vessels.(5) The dust-cell aggregates are relatively acellular but when tuberculosis is superadded thereis an excessive cellular and fibrotic reaction.(6) The difficulties of defining the radiological and pathological appearances of early pneumokoniosisare discussed.(7) The incidence of pneumokoniosis in 7,653 workmen with 5 or more years’ undergroundservice was 43-75%, but it is suggested that in future the incidence will be appreciably lower.(8) The methods of- dust production and the chemistry of mine dust are described. It isshown that the free silica-content of air-borne mine -dust is relatively low.(9) The aetiology'of the pneumokoniotic lesion is discussed."

Jan 1, 1947

By M. Westerstrand

The processes involved in the concentration of magnetite ore with process water as the aqueous medium can have a strong influence on the surface properties of the magnetite particles. In this study, different leaching methods, as well as zeta potential measurements, were used to examine the major easily accessible ions on the particle surfaces and their effect on the surface charge. The results show that the enrichment of elements on the surface of the particles appears early in the refinement process. Ca was enriched up to 15 times and Si up to 50 times compared to what pore water alone would have given. The leaching experiments also showed that the addition of water glass increased the surface enrichment of Si and that the collector might hinder desorption of Ca. An alkali leaching method was evaluated, which showed that Si was much more enriched than S and Cl. Zeta potential measurements on synthetic magnetite particles showed that process water resulted in zeta potentials different from the potentials measured for these particles in aqueous calcium and silicate solutions. Therefore, it is important to consider the complexity of the process water when making predictions about the properties of the particle surfaces in the final magnetite concentrate, which most studies do not. Zeta potential measurements were also used to rule out a strong influence from organic matter in the process water on the magnetite zeta potential.

Ground-water and tailings pond monitoring in the Upper Santa Cruz Basin Mines Task Force&apos;s Special Studies Area has been performed to determine the nature and extent of aquifer contamination from copper tailings pond&apos;s recharge in the basin. A monitoring program for each of three mining areas (Mines A, B, and D) was developed. Analysis of data shows that recharge from Mine A&apos;s ponds has caused increased hardness, sulfate and total dissolved solids in local ground water. However, pumpage in the area has controlled most of the water&apos;s movement. Pond recharge from Mine B has led to similar conditions, and the degraded water is moving towards a local public-supply well. Pumpage from Mine D&apos;s interceptor wells is controlling some, but not all, of the movement of recharge seepage from Mine D&apos;s ponds. Recommendations include the need for enhanced monitoring programs at each current mine site, development of a monitoring program for Mine C&apos;s area, development of water budgets for all mines, investigation of tailings pond compaction and sliming, establishment of mine closure plans for containment of recharged pond water, and the need for additional interceptor wells in several locations.

Jan 1, 1983

By A Horn

Mineral processing is characterised by a constant adaptation to changing raw materials and market conditions. It is the link between the mined raw material and a marketable product. As a lot of high-grade reserves are exploited, a steady deterioration of raw material quality can be observed. At the same time, the customer’s requirement for product purity and consistent quality increases.Over recent years beneficiation techniques for iron ore fines have become more important in order to achieve a maximised utilisation of ore resources and to produce competitive products according to international standards.Many high capacity iron ore beneficiation plants that target the production of fines focus on gravity separation processes using fluidised bed classifiers and spirals or wet high intensity magnetic separators as an alternative. This paper demonstrates the suitability of utilising the allflux® two-stage fluidised bed classifiers to treat iron ore particles up to 2 mm in size as well as showing how the high capacity gaustec® wet high intensity magnetic separation (WHIMS) technology offers several advantages compared to other WHIMS technology.The combination of the allflux® and gaustec® technologies offer the following benefits:The two-stage fluidised bed classification extracts a significant amount of concentrate from the feed. This in turn reduces the feed capacity required for the gaustec® WHIMS located downstream.The second classification stage produces a -0.5 + 0.1 mm product and a -0.1 mm product. The efficiency of the magnetic separation on these classifi ed products is high due to optimised settings for each size fraction.

Jul 11, 2011

"The present and possible futures commercial production of potash from various sources in the United States is discussed below under the following heads:1. Potash from the saline lakes.(a),Nebraska lakes.(b),California lakes.(c),Other lakes.2. Potash as by-product from the cement kilns.3. Potash as by-product from the iron blast furnace.4. Potash from silicate rocks.(a),Feldspathic material.(b),Leucite rocks of Wyoming.(c),Sericite slates of Georgia.(d),Glauconite (greensand) of New Jersey.5. Potash from Alunite.6. Potash from organic sources other than kelp.7. Potash from kelp.In this discussion very little more than passing reference, if any, will be given to those projects which up to date have been de¬veloped only slightly, if at all, beyond the small scale laboratory stage, or for the development of which there appears to be very little financial and technical backing at the present time. Nether or not many of these proposed projects have merit can be determined only by an actual operating demonstration.Generally speaking, the potash industry of the United States has been hardly more than marking time since the armistice. This is, largely due to the fact that the consumers of potash have been expecting that heavy shipments of foreign potash to the United States would be resumed soon at somewhere near the pre-war prices, and they have not been buying domestic potash at present prices for many months. The result has been that domestic producers have been unable to sell their product at even cost and many producers of potash have been obliged to close down. Thu Nebraska lake plants were closed down in February. The California saline plants were operating at below capacity, and the only large alunite plant is closed down. Even the cement plants have little or no inducements to recover the potash being lost in their waste gases, and the production is very small at present."

Jan 1, 1919

By George J. Young

(San Francisco meeting, October, 1911.) THE nature of slimes handled in the treatment of gold- and silver-ores has been discussed in technical literature to a considerable extent. The subject of slime-filtration from the practical worker&apos;s stand-point has also received much comment, and scattered through the literature of the subject are descriptions of many slime-filtration installations. Articles of this nature serve a valuable purpose and assist materially in the design of new and the improvement of old plants. The subject of the physics of slime-filtration has been touched upon to only a slight extent. The underlying principles are worthy of more intensive study and experimentation than they have received, and the main purpose of this paper is to present the results of such study and experimental work as will serve to make clear in part at least many of the principles which control the filtration of slime. Nature of Slime. Much has bean written concerning an accurate definition of the term ? slime," but no comprehensive definition seems to be generally accepted. The reason for this is clear. A slime consists of at least three different substances, each, when separated, possessing distinctly different physical and to a certain extent chemical properties. These substances are extremely fine sand, a colloidal material which may be and generally is in a coagulated condition, and a colloidal material which is in a non-coagulated condition. Suspending a slime in a relatively large volume of water by shaking and allowing sedimentation to take place, results in the fine sand settling out with comparative rapidity, followed by the coagulated material, which settles much more slowly and finally a certain portion remains

Nov 1, 1911

By Rudi Podjadtke

In a short chronological review the development concepts and improvements in steel roadway support are shown. The successful standardization concept of RAG Deutsche Steinkohle and currently used support systems are important topics. The history of optimizing the material properties for the steel arch support with different alloys up to the tempering used today is discussed. The present-day application of the steel support is additionally presented. Today, it represents a system component of modern roadway support also for highly stressed roadways. In addition to the yielding roadway arch support, this overall system - the combination support - consists of the additional components of a rockbolting system and concrete backfilling. The comparison of the application areas for each individual partial system with the overall system illustrates its high performance capability. Actual practical experience with the state of the art typed steel arches are pointed out exemplarily. Understanding the complete system permits the selection of the economically optimal support for all conditions.

Jan 1, 2008

By Bruno KERL

THE list of deaths reported during the year 1905 comprises the following names (the figures in parentheses indicating the year in which the persons named were elected to membership:- Honorary Member.-Dr. Bruno Kerl. Members and Associates.-Charles Christy Adams (1903), John Wesley Anderson (1898), William Burton Barber (1901), Thomas A. Bennett (1900), Luke W. Bryan (1901), Edwin S. Daugherty (1905), William Scott de Camp (1875), George H. Eldridge (1889), B. W. Frazier (1871), John Broome Guinn, Jr. (1897), Dana C. Irish (1900), Harry Hugh Lee (1899), William Alfred Lindsay (1902), Roland C. Luther (1884), James MacNaughton (1890), Gordon McLean (1899), Herbert Holmes McNamara (1902), August R. Meyer (1886), William Orr (1897), William J. Parker, Jr. (1898), Joseph Phillips, Jr. (1895), Charles O. Ripley (1902), Emmerich J. Schmitz (1883), Ludwig Philip Seeger (1900), Jacob Johnston Sperry (1900), Gustavus H. Stoiber (1902), William L. Study (1905), Robert Macnair Wilson Swan (1900), Richard Henry Terhune (1886), Joseph Thiry (1892), John N. Tisdale (1903), Alfred Isham Totten (1897), Walter H. Virgoe (1902), Charles H. Wellman (1890), Harvey L. Williams (1903). Of these, Dr. Bruno Kerl and Prof. B. W. Frazier have been made the subjects of special Biographical Notices in the Bi-Monthly Bulletin 1 the former in No. 4, July, 1905, p. 743, and the latter in No. 5, September, 1905, p. 1097. Concerning the remainder of the list, the following paragraphs comprise such information as could be obtained by the Secretary. Charles Christy Adams, who had been a member of the Institute since 1903, died in Johannesburg, South Africa, August 31. 1905. He was born in New York City, July 13, 1849, and received his technical training at the Colorado State School of

May 1, 1906

The design/optimization of the pump and cyclones to maximize grinding circuit efficiency first requires a concise understanding of, and clearly defined specifications for, desired grinding circuit performance. Subsequently, the pump and cyclone performances that provide the desired grinding circuit performance can be defined. Once the performance requirements of each process unit are determined, selection of physical equipment parameters that will deliver those performances can be carried out. The Functional Performance Equation shows that there are two distinct efficiencies in closed circuit ball milling. One of these, ?Circuit Classification System Efficiency? (CSE), is the fraction of ?coarse? material inside the ball mill upon which grinding energy is deliberately expended, versus the remaining fraction of ?fines? or finished size material inside the mill, upon which grinding energy is wasted (on over-grinding). The role of the pump and cyclones is to maximize CSE, which is the desired grinding circuit performance. The obtainable, target CSE for any given circuit can be estimated, for example by referring to a plant data base of CSE?s. Design/optimization guidelines then allow us to specify the pump and cyclone performances that will achieve the target CSE. This paper outlines the step-by-step, systematic method of pump and cyclone selection which maximizes CSE. Numerous examples of its successful application are provided.

Jan 1, 2011

By D. Brosnahan, J. Gathje

Newmont Metallurgical Services (NMS) recently acquired a Scanning Electron Microscope (SEM) with a JKMRC/FEI Mineral Liberation Analyzer (MLA). With the MLA software package, raw particle image and X-ray data can be converted into particle mineral maps and bulk and liberation data can then be calculated for minerals of interest. This type of quantitative mineralogical data can then be used for a wide variety of applications. Ore characterization with MLA can be carried out for existing or processing plants in development. MLA characterization of laboratory test products provides valuable liberation information that assists the research metallurgist in better planning and developing process treatment options for various ore types. This paper describes the use of MLA characterization in a copper flotation test program where the use of various testing options for arsenic depression was being evaluated.

Jan 1, 2007

By B. C. Vargas

The Toulon tunnel project is a key component of the Highway corridor on the French Riviera between Marseille and Nice and is a fundamental transportation infrastructure for the region. The first design studies started in the 1960?s. The tunnel project is made of 2 separate tunnels: South and North tunnel. The North tunnel was built between 1992 and 2002 after 10 years of difficult construction (for example, on March 15th, 1996, a collapse of the tunnel in the ?Marchand Area? generated a sink hole in the city Center, causing 20 months delay). The South tunnel alignment runs parallel to the North tunnel at the same depth below Toulon historical downtown (20 to 40m depth with some areas with less than 10m of cover). The Risk management program was studied to be a State of the Art program in urban tunneling construction. The Hydro Geological Context The whole project area is covered with backfills and colluviums of 1 to 4m thick. The Schist, marls and sandstones, randomly distributed along the alignment below the first layer have different characteristics. While the Schist are pretty compact, the marls are fractured. The other layers have very different characteristics, and many faults are located along the alignment, especially in the limestones. The Breccia are heavily decompressed and deformable, as well as the other soils located in the Marchand Area. This 80m long area is where the settlements need to be controlled with an extensive monitoring program. The complete Geological profile is presented in Figure 1. [ ]

Jan 1, 2012