Search Documents

By John C. Calhoun, Frank T. Bethel

The application of a method for analyzing pressure build-up curves to determine the effective permeability in the Spraberry is presented. Sixteen upper Spraberry wells of the Driver area arc analyzed and show variations in the in-place effective permeability of 2 to 183 md. Since these value- are much larger than the .5 md. or less reported for the matrix rock. a large part of the vertical fractures noted in Spraberry cores- must be considered native to the formation. The effectiveness of the well fracture treatment in connecting the well bore to the native fracture system is analyzed by comparison of the effective permeability as determined from the PI test to that obtained from a pressure build-up curve. These results show that the fracture treatment is sufficiently effective in connecting tile well bore to the native fractrure system to yield a flow capacity within about 50 per cent of that dictated by the native fracture system About two-thirds of the wells show some degree of local blockage. INTRODUCTION Fractured reservoirs have been known in the past.' However, during the past two years the Spraberry formation has directed the attention of the petroleum industry to a study of the performance of a fractured reservoir. The large variation in the number of fractures noted in Spraberry cores rile large variation in the producing ability of offset well.. the dramatic effect of well treatment on well ,productivity. the unknown quantity of oil stored in the fractures and matrix rock. and the unknown oil to be recovered were part of the initial Spraberry puzzle. In this type reservoir where the well treatment is an important factor in determining the productivity. it i- particularly desirable to determine the in-place flow capacity of the drainage area at distance* far removed from the well bore. This value. when compared to the flow capacity obtained from a PI measurement, will show the effectiveness of the well treatment (completion. fracture treatment, acidization. etc. in establishing a flow capacity in the vicinity of the well bore equal to that in the more remote region. The object of this paper i.; to show the application of a method of pressure build-up analysis for this purpose in studying the Upper Spraberry formation in the Driver area. STATEMENT OF THEORY The theoretical basis for the application of a pressure buildup curve to show the effective permeability of the rock at distances far removed from the well bore has been presented in detail in earlier publications.', in the previous development it was shown that pressure build-up behavior of all wells could be reduced to the same dimensionless build-up curve of Fig. 1. This mean.; that the bottom hole pressure of a well after hut-in will rise in such a manner that a plot of pressure against the logaritllm of time yields a straight line. The slope of this linp can be rlzed to calculate the effective permeability as expressed by the following equation: where: effective oil permeability md oil production rate prior to shnt in. STB/I) In practice the flow which occurs into the well bore after shut in and the variation in flow capacity in the immediate vicinity of the well bore usually cause the early part of the build-up curve to be unsatisfactory in the determination of permeability. In general the effect of these factors on the straight line section will become negligible after a time when the of the following equation is equal to 0.1. and the preferred section Of the curve for use in defining the slope lie-

Jan 1, 1953

By McHenry Mosier

This paper constitutes the third progress report on a national survey of the use of detachable bits in metal mines. It presents comparative costs of drilling with conventional and detachable bits and describes the operating practice in rock drilling and the reconditioning of drill steel and bits at 10 mines not discussed in previous reports.3/ ACKNOWLEDGMENTS This report has been prepared with the assistance and cooperation of the officials and staff members at the mines visited. Costs and other data at individual mines were developed and furnished by the operators.

Jan 1, 1937

Virtual Reality (VR) simulations are excellent tools for training, education, simulation of abnormal and dangerous conditions in mines and solving complex problems. Although the concept of VR has been around for nearly half a century, it has taken recent advances in hardware and software to bring this technology to within the budgetary reach of ordinary users and researchers. VR is now successfully being used in the minerals industry for: data visualization, accident reconstructions, simulation applications, risk analysis, hazard awareness and training. The Institute of Sustainable Minerals Industry, Advanced Computer Graphics and Virtual Reality Research Group (SMI-VR) at the University of Queensland, established in late 2000, has been involved in developing VR applications for the minerals industry in conjunction with various research centres. This paper illustrates the benefits of using advanced computer graphics and VR techniques in the minerals industry with some examples of applications developed.

Jan 1, 2003

By Wilton Johnson

The Bureau of Mines study indicates that land utilized by the mining industry for mineral extraction and processing from 1930 through 1980 amounted to 5.7 million acres, or 0.25 percent of the land mass in the United States. Land reclaimed by the industry during the same period was 2.7 million acres, or 47 percent of the land utilized. Land use by the mining industry includes surface land used for excavation or mining, for waste from underground mining, and for wastes from milling or processing operations. Data on land use for disposal of overburden waste from surface coal mines and on areas affected by subsidence associated with underground mining are included for the period 1930-71 only. The 10 leading States in total land used for mining over the 51-year period were, in decreasing order, Pennsylvania, Kentucky, Ohio, Illinois, West Virginia, Florida, Indiana, California, Alabama, and Missouri. Seven mineral commodities accounting for 92 percent of land use are, in decreasing order, bituminous coal, sand and gravel, stone, phosphate rock, clay, copper, and iron ore, all predominately surface mined. Bituminous coal production was responsible for nearly half of the total area utilized. Reclamation of mined lands and waste disposal sites over the reporting period was largely on lands utilized in mining bituminous coal; 75 percent of the land used for bituminous coal production was reclaimed.

Jan 1, 1981

By P. Venter, N. Naude

"Coal mining is a thriving industry and 53% of the coal mined in South Africa is used for electricity generation. Mechanization has made coal mining more efficient, but fines generation has subsequently increased. Up to 6% of the run of mine material can report to the -200 µm fraction. Common problems associated with fines handling include dust formation, storage problems, and high moisture levels. A method to turn this material into a saleable product instead of stockpiling it can add value to a company.Briquetting is a pressure agglomeration method where loose material is compacted into a dense mass (FEECO International, 2014). The briquettes must be able to withstand rigorous handling and transport operations without disintegrating. This study aims to investigate the optimum binder and moisture conditions required to produce a mechanically strong briquette using two different binders - a PVA powder (binder A) and a starch powder (binder B).It was found that for binder A the optimum moisture level was 12% to 14%. At this moisture level the greatest compression strength gains were observed, and low amounts of fines produced in impact and abrasion tests. The minimum amount of binder added while still obtaining a strong briquette was 0.5% binder A. For binder B the optimum moisture level was also 12% and the minimum amount of Binder B to be added was found to be 1%. Briquettes that were dried outside reached their peak strength after about four days, whereas the briquettes that dried inside took about 20 days to reach their strength plateau. Hardly any degradation took place on the surface of the binder A film after exposure of 300 hours of artificial weathering. Thermogravimetric analysis confirmed that neither binder A nor binder B will add to the ash content of the coal fines, as both binders totally decompose above 530°C.Binder B yielded stronger briquettes after 15 days and also generated less fines. It is therefore superior to binder A and would be recommended for further use.Paper written on final year project work carried out in partial fulfilment of B.Eng degree in Coal Beneficiation"

Jan 1, 2015

By P. V. Avotins, I. Djurkovic, D. R. Nagaraj, M. Grunjic, A. Day

"As part of a major reconstruction and expansion of the Majdanpek Copper Mine, an investigation and optimization of the flotation collector regime was undertaken. The flotation response of the major minerals to various reagents and the effect of pulp chemistry was studied from both a fundamental and practical point of view. These studies led to plant trials and the eventual adoption of a modified collector suite which improved both copper and gold recoveries.INTRODUCTIONThe Majdanpek Copper Mine processes 40,000 tons per day of ore containing about 0.43% cu. In addition to copper, the ore also contains recoverable quantities of molybdenite and gold. The mine has been in operation since 1961 and is the largest in Yugoslavia. It is currently undergoing major reconstruction and expansion. The flowsheet of the Majdanpek concentrator is shown on Figure 1.The ore body is variable in composition and changes in mill feed require proper control of operating variables to achieve the optimum metallurgical results. A detailed study including grindability, flotation response, and solid-liquid separation was carried out on several samples of the ore. Flotation response and the choice of reagent chemistry were found to be very important in achieving the highest recoveries of metal values. An automatic reagent control scheme insured that optimum dosages were used in the plant.The flotation collectors used at the present time include sodium isopropyl xanthate (SIPX), AERO 3302 Promoter and AERO 5415 Promoter. The addition of AERO 5415 to the reagent suite is a recent development and was based on the favorable results obtained in the extensive laboratory testing program conducted to establish the optimum reagent combination and dosages. Subsequent plant tests confirmed that AERO 5415 provided significant improvements in copper and gold recoveries. A description of the mineralogy of the Majdanpek ore and details of laboratory and plant metallurgical data are given in this paper. The chemistry of AERO 5415 Promoter and its interaction with minerals relevant to Majdanpek ore are also discussed."

Jan 1, 1992

CONTENTSSummary.Introduction.Location and Geology.Historical and Exploitation.Part 1. Washability Characteristics of the Liddell.Seam.Foybrook Open Cut, Top Bench.Sampling.Size and Ash Distribution.Washability Data.Washery Separations.Part 2. Washability Characteristics of the LiddellSeam.Foybrook Open Cut, Bottom Bench.Sampling.Size and Ash Distribution.Washability Data.Washery Separations.Acknowledgments.References.INTRODUCTIONThe washability characteristics, size-range and chemical analyses of the screening from the Liddell Seam are matters of growing interest in view of the increased exploitation of this seam over the last few years, and also since the Newdell Coal preparation plant of the New South Wales Mining Company Proprietary Limited, utilizing magnetite heavy media separation, commenced...

Jan 1, 1954

By L. W. Hamel

"Two 35 foot diameter enviro clear thickeners were tested in series as CCD units from June until October, 1978. Up to shutdown in July, we ran with automatic bed level control via the level probes and underflow pinch valves. Despite extensive efforts, we were unable to eliminate the surges created between the units by the opening and closing of the pinch valves. Early in July, the best rake speed and gap setting were determined. After shutdown, the enviro clears were run by manually controlling the pinch valves. These efforts were successful.A few mechanical problems were encountered while operating the thickeners. New units should incorporate more support for the drive coupling and a rubber feed seal. A few modifications of the instrumentation control scheme will be required before the units can be fully automated. A less sophisticated automatic flocculant addition system will accomplish the desired results. Control of the underflow withdrawal via the pinch valve should be investigated further. Our best results were obtained by keeping the feed volume to the No. 1 enviro clear constant. Surges were controlled by opening or closing both underflow valves proportionately.Capacity of the enviro clears is dependent of many variables. The ore treated during the test program was much finer than that reported on in R & D Project Report 76-02. Conditions were never steady enough to determine best flocculant dosage or addition point(s). The lowest soluble losses were obtained at very high wash rates. The underflow densities drop but the soluble losses also drop. Regression equations were developed in order to assess the effect of the various parameters. Within the range studied, these equations will predict the performance of enviro clear thickeners as CCD units on Elliot Lake ores. Our results show that the enviro clear thickeners are a viable alternative to the conventional CCD thickener."

Jan 1, 1979

By Joseph Clare, Elizabeth Anderson, Mike McGinley, Ron Hines, Judy Cochran

The South Lake Union Pipelines contract for King County Wastewater Treatment Division and Seattle Public Utilities in Seattle, Washington included three 1.8 m (72-in)inside diameter microtunneled pipeline segments totaling about 793 m (2,600 lf).Tunnel alignments were within street right-of-way of heavily traveled urban roadways. Project challenges recognized in the design included: high groundwater levels; contaminated soil and groundwater; variable soil conditions, including fill; and timber piles and other obstructions remaining from historic land uses. The tunnels were built using a Lovat MTS Microtunneling machine, beginning in spring 2003. Conditions encountered during construction presented additional challenges beyond those anticipated in the design process, and were successfully addressed by the owners, designer, and construction management consultant all working with the contractor. Problems included highly variable soil conditions, cracking of reinforced concrete pipe joints during pipe jacking, a timber pile trestle uncovered during shaft construction, and obstructions encountered in the second and third microtunnel runs.

Jan 1, 2005

By L. Crocker

The Bureau of Mines investigated processes for recovering a marketable lithium product from the montmorillonite-type clays of the McDermitt caldera. The clay deposit, located on the Nevada-Oregon border, is estimated to contain over 3 million short tons of lithium. Limestone-gypsum roasting and selective chlorination proved most successful for extracting lithium from the clays; 80-pct Li recovery was achieved using either technique. With both processes, lithium silicate in the clay was converted to a water-soluble compound-either lithium sulfate or lithium chloride. The lithium was then recovered as a carbonate by water leaching the calcine, concentrating the leach solution by evaporation, and precipitating the lithium with soda ash. The operating costs for the limestone-gypsum roast process were estimated at $2.02/lb Li2C03; selective chlorination operating costs were estimated at $3.85/1b Li2C03. The current selling price of Li2C03 is about $1.50/lb. A detailed flowsheet, material balance, and process evaluation are presented for the limestone-gypsum roast process. In addition, lithium reserves and resources are discussed and the McDermitt clays are described.

Jan 1, 1988

By Steven D. Wirch

Abandoned underground coal mine areas must either be sealed or ventilated to comply with federal mine regulations. Ventilation of these abandoned areas is often impractical due to roof falls and inadequate primary mine ventilation. If the area is sealed, a very complex ventilation system is set up. In which the gob "breathes" in and out due to barometric pressure fluctuations. The Gob Assistant is a computer program (for use on IBM compatible personal computers) which allows the prediction of air flows into and out of a sealed mine area. Gas flows with applicable control techniques are also modeled. This information is presented to the user who will decide which control technique, or combination of techniques will ultimately be applied. The Gob Assistant is an intelligent gob simulator that can reduce the guesswork involved in predicting the effects of sealing and control techniques before they are applied. This paper provides the fundamental principles upon which the Gob Assistant is based, verification of these principles, and an explanation of how these principles were integrated into the Gob Assistant.

Jan 1, 1988

By Fiseha Tesfaye, Pekka Taskinen

"Thermodynamics of the equilibrium phase assemblage Ago_9Cul.lS-Cu2-xS-CuS have been studied by an EMF -method. The ternary phase was synthesized from the pure Cu2S and Ag2S in vacuum furnace at high-temperature and mixed with appropriate compositions of Cu2S and CuS to form the cathode electrode. The EMF-measurements were made on the solid-state galvanic cell Pt(-) I Ag I RbAg,ils I Ago9Cu1.1S-Cu2-xS-CuS I Pt(+), in a temperature range from 316 K to 498K.Based on the measured EMF vs. T relations, thermodynamic functions (?fG° , ?fS and ?fH°) of stromeyerite (Ag0.9Cu1.1S) in equilibrium with Cu2-xS and CuS have been determined. The obtained experimental values have been compared with the available literature values. New experimentally determined thermodynamic properties of the solid solution (Ag,Cu)2Sss were determined.IntroductionDue to intense mining of high grade sulfide ore minerals in the past, recently, the available sulfide ores are poor in metals and becoming increasingly complex; such that, the production of high grade metals by the conventional pyrometallurgical processes is compromised. Consequently, smelters are in need to modify their operating flow sheets and strategies for processing more complex feed materials economically, while meeting the strict environmental regulations. To make the appropriate modifications, accurate thermochemical data of phases and phase assemblages which exist in these complex ore minerals are essential.Silver-bearing sulfosalts are encountered in ore minerals for the production of base metals and are common sources of silver. Among the silver-based sulfosalts, stromeyerite (Ag0_9Cu1.1S) is relatively common ore mineral in most hydrothermal vein and replacement deposits [1]. Recently, the ternary chalcogenide compound Ago0.93Cu1,07S has been studied, intensively, due to its high ionic conductivity and gradual disorder in the sequential phase transitions [2]. Therefore, accurate knowledge of the thermodynamic properties of stromeyerite has considerable fundamental and practical interest in many aspects of extractive, chemical and physical metallurgy."

Jan 1, 2014

By T. R. Curr, R. T. Jones

Keywords: Pyrometallurgy, Mintek, DC arc furnace, plasma, smelting, chromite, ilmenite, cobalt, slag, zinc fuming, dust, magnesium, laterite, ferronickel, arc modelling, Pyrosim, thermodynamics The Pyrometallurgy discipline at Mintek was initiated in the early 1970s, to support a growing ferroalloy industry in South Africa. In addition to a range of pyrometallurgical options, Mintek specialises in DC arc furnace technology and has pilot plant facilities up to 5.6 MVA, as well as a strong base in process and arc modelling. Industrial processes have been developed for ferrochromium production, ilmenite smelting, and cobalt recovery from slag. Recent work has been done on such processes as the production of ferronickel from laterite ores, the fuming and condensation of magnesium, and the recovery of platinum group metals from 'difficult' feedstocks.

Jan 1, 2006

This report summarizes the work performed and results achieved in the period from 18 June 1971 through 18 October 1971 under Phase I (Task 1: Literature and Industry Search; Task 2: Conceptual Design and Evaluation; and Task 3: Concept Selection and Preliminary Design) in substantiation of the drill/impregnation machine concept recommended for detailed design in Phase II. Also included as Task 5 are recommendations for an experimental investigation to be conducted during Phase II. The report is submitted for approval and authorization to proceed to Phase II.

Jan 1, 1972

By R. R. Brown

The solubility and the activity of aluminum chloride hexahydrate, A1C13?6H2O, in aqueous solutions were determined as a part of the Bureau of Mines, U.S. Department of the Interior, research to improve mineral processing technology for recovering alumina from low-grade domestic resources. The solubility of A1C13 in pure water was found to be 31.09 and 31.77 wt-pct at 25° and 85° C, respectively, and decreased drastically to 10 and 0.1 wt-pct when the respective amounts of 20.3 and 37 wt-pct hydrochloric acid (HCI) were added in solution. The equilibrium constant for the solubility of hexahydrate, activities, and activity coefficients of A1C13 and H2O were calculated and compared with the results from the available methods of estimation. The results were shown to be useful in leaching nonbauxitic ores for extraction of alumina by changing the solubilities of component salts upon addition of HC1. Simultaneous solubilities of A1C13, FeC13, KC1, and NaC1 in solutions of HC1-H2O were also determined and their effects on the purity of A1C13?6H20 crystallized from mixed salt solutions are briefly discussed.

Jan 1, 1979

By Eric M. Klein

As part of the Woodrow Wilson Replacement Bridge project several damaged wetland and environmental areas were to be mitigated. One of the mitigation projects consisted of constructing a Denil fish ladder around Peirce Mill Dam in Rock Creek National Park, Washington, D.C. The dam is a historic structure operated by the National Park Service. The fish ladder is located between the east abutment of the dam and Beach Drive, a major collector road. Construction of the fish ladder required removal of a portion of the east abutment and an excavation that extended about 22-ft below the pavement of Beach Ave. It was not possible to close Beach Drive except for very brief intervals or at night; therefore, a support of excavation system that would minimize disruption to the public was required. The high groundwater required that the groundwater be cut off prior to excavation; the random rubble and soil fill, and shallow but erratic rock surface precluded driving sheet piling. A jet grout system was selected because the grout probe could penetrate the rubble fill, stabilize a variety of soil conditions, and cut off the ground water prior to excavation. It was not possible to construct a stable wall without tiebacks or soil nails. Given the schedule and tight working conditions it was decided that soil nails through the jet grout wall facing would be the most cost effective method, as it did not reduce the working space as rakers would and would be more cost effective than prestressed tiebacks.

Jan 1, 2006

By F. N. Kissell, C. D. Litton

This study predicts the level of smoke that miners might meet while trying to escape a coal mine fire and describes how smoke would impede their safe escape. For this study, the authors assumed that miners exit through an escapeway adjacent to the burning entry, that some air would leak from the burning entry to the escapeway. The following conclusions were made: • A very low amount of air leakage to the escapeway can produce a critical level of visual obscurity from smoke. This shows that intake airways may be as susceptible to smoke visibility problems as return airways. • This critical level of smoke obscurity is reached much before a critical level of carbon monoxide is reached. • Small fires can cause a severe sensory irritation that further limits vision. Thus, reliable eye protection is very important. These results show that methods to guide miners through dense smoke will contribute greatly to saving lives during mine fires.

Jan 1, 1993

By E Ah Mu and C R Lilley, A D. Campbell

Cave propagation is a complex process due to interacting variables such as mine geometry, rock mass heterogeneity and complex structural networks and stress fields. The Ernest Henry sublevel cave (SLC) is directly below an open pit, which provided an opportunity to observe and measure rock mass failure as the cave initiated and propagated through the pit wall. This paper describes interaction between the open pit and SLC as well as rock mass failure mechanisms observed from the start of the SLC to surface breakthrough.Cave propagation and slope failure mechanisms were found to be governed by intermediate structures, while the cave shape was largely controlled by cave-scale faults. The open pit, production-level geometry and production draw strategy were also important factors for cave and subsidence growth. Cave propagation was episodic and asymmetric in shape due to the orientation and relative position of geological structures, combined with the effects of the increasing SLC geometry and drawdown from the underlying production levels. The precursors and failure mechanism of a 2.5 Mt wall collapse are also reviewed in detail.Cave growth was simulated using a 3D, non-linear, discontinuum finite element model coupled with Newtonian Cellular Automata. Model results are compared to field observations and monitoring data to determine the accuracy of forecasts and compared models versus actual rock mass response during cave propagation.CITATION:Campbell, A D, Ah Mu, E and Lilley, C R, 2016. Cave propagation and open pit interaction at the Ernest Henry Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 311–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By H. J. Sutherland

This paper reviews the results of the subsidence research prop ram at Sandia National Laboratories. The manuscript highlights the following: the application of empirical methods (profile functions) to the subsidence above longwall panels in the U.S.; the use of the "rubble model" to describe the behavior of broken strata as it distends when it falls to the Mine floor (or top of the rubble pile) and then is subsequently compacted as it is loaded by overlying elements of strata; and, the application of physical modeling techniques (centrifuge simulations) and numerical techniques to study the failure mechanisms in highly structured stratigraphy. The capabilities of the latter two are illustrated ')y comparing their predictions to the results of a field case that has complicated stratigraphy.

Jan 1, 1982

By Víctor Cárdenas

El presente trabajo describe el manejo de las herramientas de calidad que aportan a la reducción de riesgos en la compañía minera La Poderosa. Para determinar los defectos, causas y consecuencias, es necesario conocer el procedimiento de control de los mismos a través del diagrama de Ishikawa o el ciclo de PHVA. Esta metodología permite encontrar la solución a los problemas dentro del aseguramiento de la calidad, seguridad y productividad de una empresa, así como establece la fuente de la causa de los accidentes por lesiones, como de los daños a la propiedad privada. En consecuencia, su aplicación se ha estandarizado en las áreas de seguridad y medio ambiente de dicha minera desde hace dos años, obteniendo resultados muy satisfactorios como el Premio Nacional de Seguridad en minería subterránea otorgado por el ISEM.

Sep 13, 2001