Search Documents

By Z X. Zhang

Ground vibrations from the blasts of the LKAB mine at the Malmberget town had reached 18-19 mm/s from year 2000 to 2002. From 2004 to 2010 the maximum vibrations had been reduced to 9 mm/s and most vibrations lowered to about 5 mm/s, indicating that the technical measures used in the mine are effective in vibration control. The major measure that has always been used in Malmberget mine is the method called Changing Initiation Sequence (CIS in short). Another method named Dividing Ring Blasting (DRB in short) is often applied to some special blast rings in the mine. Both methods have been proved to be successful in vibration reduction, and they do not need any additional costs. Because of the two methods, both maximum vibrations and average ones have been reduced by around 50% since 2004.

Jan 1, 2012

By P. Coghill, P. Revell

"Geo-sensing is the ability to routinely measure or infer rock properties at a range of scales using non-destructive scanning devices. These devices can provide information and data flows to support integrated decision making across the minerals value chain. Geo-sensing has been used for many years in minerals exploration using technologies such as satellite imaging and airborne geophysics but to date the use of sensing technologies in between the mine and mill has been very limited. The aim of this research is to develop new mineral sensing technologies that can enable grade engineered ore streams through the rejection of low value gangue or deleterious elements either in the pit or during transfer to the mill. This paper focusses on the research and development being carried out by the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE) and its associated members on new sensing technologies. At the start of their development these technologies were classified on the Technology Readiness Level scale at 3 (TRL3), equivalent to a proof of concept. Laboratory testing and design is aimed at progressing these sensing technologies to TRL5 which is ready for testing at an end users site. New data obtained during the laboratory testing and design phases are presented in the paper demonstrating performance specifications such as detection limits and measurement speed which can be used to infer the pod size of gangue that can be rejected at scale. Grade Engineering® and coarse gangue rejection are considered as key drivers for the mining industry to address the higher mining, processing and environmental costs associated with ore bodies with declining grades. This is an industry wide problem and the development of mineral sensors is seen as key enabling technologies for Grade Engineering® and coarse gangue rejection. The technologies presented in this paper enhance value through early decision making of ore quality and improve the overall resource value case through improved grade and throughput engineering."

Jan 1, 2018

By Kenneth L. Cashdollar

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRL Lake Lynn Experimental Mine and after laboratory explosions in the PRL 20-L chamber and the Fike 1-m3 chamber. The dusts studied included both high and low volatile bituminous coals. Low temperature ashing for 24 hr at 515°C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as or higher than the initial incombustible content. The MSHA alcohol coking test-was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared to the initial dust loadings to determine the transport distance of dust during an explosion. All of these data will be useful in future forensic investigations of accidental dust explosions in coal mines or elsewhere. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health or the Mine Safety and Health Administration.

Jan 1, 2006

By G. R. Hopkins

"Refiners are generally considered solely as fuel producers, but actually they also comprise a group one of the largest consumers of fuel. For example, during the year 1929 the refineries-burned 51,544,000 barrels of oil as fuel, or the equivalent of over 5 per cent of the crude oil processed in that year. In addition enough other fuels - coal, natural gas, refinery or still gas, and petroleum coke - were utilized to raise the total fuel consumption based on B. t. u. equivalent to more than 10 per cent of the heat value in the total crude oil run to stills. Refineries utilize fuel chiefly as the heat-forming element distillation, but also under-boilers in the formation of steam used in refining, for the heating of buildings, and in the generation of electricity.In the early days of refining, the problem of fuel utilization and fuel economy was of scant importance to the refiners. Margins of profit were comparatively high and the major portion of the operatros1 attention was directed toward increasing their throughput. However, the keen competition that has prevailed in the refining industry over the past five years or more has taught the refiners that their expenses, one of the largest items of which is the cost of fuel, must be curtailed. Thus in 1925 the refiners used an average of 829,000 B. t. u. to refine a barrel of crude oil, wheras by 1929 this average had been reduced to 639,000 B. t. u., a decline of 23 per cent (see fig. 1)Since 1925 oil has ranked first as a refinery fuel (see fig. 2). The use of natural gas increased during 1926 and 1927 but declined in 1928 and 1929. On the other hand, the use of refinery gas has grown rapidly in importance. Coal has shown a steady decline in use at refineries since 1925. Petroleum coke has never supplied more than a very small fraction of the total fuel requirements, although there has been a steady increase in its use."

Sep 1, 1930

By Miezitis Y

A weak airborne radiometric anomaly was examined in the field and the presence of uranium confirmed. Rotary-percussion drilling showed the presence of uranium but a subsequent programme of diamond and rotary percussion drilling indicated that the concentration of uranium was uneconomic. Within the tufts and volcanics of the prospect the uranium existed as uranyl phosphates within the oxidized zone. Geological mapping and the diamond drill core showed that the Stag Creek Volcanics are part of the Lower Proterozoic Masson Formation, probably with member status, rather than the expression of an Archaean basement ridge. This change in the interpretation of the fundamental structure of the Pine Creek Geosyncline has led to a reexamination of the stratigraphy and to suggestions which differ from the current concept.

Jan 1, 1977

The Mount Lyell Mining Field is Australia's chief productive source of copper. It is situated near Queenstown, on the western flanks of the West Coast Ranges, about 20 miles from the west coast of Tasmania (Fig. 1).The following observations on the mineral composition of the copper ores of the Mount Lyell Field are based on a...

Jan 1, 1939

By L. D. Gent

This report reviews the current state of the art of remote control techniques for underground continuous miners. A delineation of aspects requiring additional data is presented. Also a summary and delineation are presented in overview form for the related section functions: roof control, haulage, ventilation, power supply and rock dusting. The automated remotely controlled continuous miner project is a long-range research effort. However, the program has been divided into intermediate steps resulting in incremental production increases throughout the program. Data are developed relating the impact of our proposed research and development accomplishments to potential productivity impact.

Jan 1, 1975

By Charles Hart

In this paper it is the author's intention to show the extent and character of foreign ores now known to be available; these deposits may be in active production or held in reserve until economic conditions may make them active. He hopes to show the relation existing between these ores and the American supply, and which of the former are now producing or will in turn come into production when our better ores have been exhausted. This phase of this discussion must of necessity include some data as to the present rate of consumption and a study of the changes we may expect here and abroad in the general steel trade and its sources of supply in raw materials. It is obvious that the occurrence of coal, ore and limestone in relation to one another and the proximity of a market are the elements in control of this feature of the problem. If the foregoing situation is favorable, all the other questions may be solved, for it is clear that with proper basic conditions finance, labor and operations will fall in line. We present a short outline of the present methods of carrying on the foreign iron ore trade, believing that it is of general interest in comparison with our own highly specialized methods, and that with the exhaustion of our better ores we will be compelled to seek a part of our supply abroad. A partial list of iron ores, with incomplete analyses (Table I), is added, to give a better understanding of the general situation and explain to some extent the reason for things being as they are in the iron and steel trade of the world and to help in bringing this paper to an informing conclusion. The question of the world supply of iron ores has been a subject for study on the part of geologists and engineers for many years, and found its best results in the Eleventh International Geological Congress, appropriately held at Stockholm, Sweden, in 1910. The proceedings are published in two volumes and are undoubtedly the best records available on this subject at the date of publication. It should be borne in mind, however, that much has happened in the 20 years since these figures were assembled. There is just as much known ore at present as at that time, minus the quantity consumed, plus newly discovered reserves. The World War had great effect upon this situation; during that time explorations were greatly reduced and the settlements after the

Jan 1, 1929

The MINER Act of 2006 mandated that all underground coal mines must install and maintain refuge chambers. Refuge chambers serve as a temporary shelter in case of emergency. Several factors affect the performance of a refuge chamber: heat production inside the chamber and introduction of CO when chamber doors are opened are two major factors. This study examines the CO purging process and to determine total air quantity and time necessary to lower the CO con-centration to safe levels for different inlet/outlet configurations using three-dimensional simulation technique. The study uses Reynolds Averaged Navier Stokes and continuity equations along with the spe-cies transport model assuming uniform air mixing. The heat transfer of any kind is neglected and the purging process is assumed to take place isothermally. The standard k-e model is utilized for simulating turbulence in the flow field. This research provides useful guidelines in developing an efficient strategy for purging refuge chamber. Keywords: Airlock chamber, Purging, Carbon monoxide, Turbulence

Feb 27, 2013

By Eldon L. Abbott, Rebecca K. Bolan

The Florida Department of Transportation, Florida’s Turnpike Enterprise is studying the feasibility of a 1128 meter (3,700 foot) vehicular tunnel to provide direct access for Port of Miami traffic to/from I-395, I-95, SR-836 (Dolphin Expressway) and Miami International Airport. Both Bored and Immersed Tube tunnels were evaluated and re-evaluated for constructing two, two-lane, 11.9 meter (39-foot) diameter tunnels beneath the Main Shipping Channel lying between Watson Island and the Port of Miami on Dodge Island in Biscayne Bay, Miami, Florida, USA. Bedrock Geology of South Florida is predominately very permeable, vuggy limestone with sand seams and occasional voids. Groundwater inflows in deep cut-and-cover excavations, tunnel buoyancy, grouting, maintenance of Port operations and potential/possible environmental impacts to Biscayne Bay were significant issues.

Jan 1, 2005

By Merwin H. Howes

Gnome shaft, situated about 24 miles southeast of Carlsbad, N. Mex., was designed and sunk by the U.S. Atomic Energy Commission for conducting a peace- time experimental nuclear explosion in the thick salt beds of the Permian Salado formation. Excavation was started July 1, 1960, and completed July 26, 1961. The 10-foot diameter shaft, lined with concrete through the rock section, was sunk 1,216 feet. A drift was driven approximately 1,140 feet on the 1,200- foot level terminating in a shot chamber. On completion of 100 feet of shaft, by means of a truck-mounted crane, facilities were installed for conventional sinking. About 709 feet of rock and 506 feet of salt were encountered in the shaft. Salt beds at this place are reported to be over 1,200 feet thick. The overlying rock section varies greatly in composition and thickness of beds and contains a 28-foot bed of water-bearing dolomite. The aquifer was sealed to facilitate shaft sinking and to prevent water-seepage damage in the salt section of the shaft. Sealing was accomplished by grout injection through holes drilled into the aquifer and by grouting behind the concrete liner.

Jan 1, 1963

By Merwin H. Howes

Gnome shaft, situated about 24 miles southeast of Carlsbad, N. Mex., was designed and sunk by the U.S. Atomic Energy Commission for conducting a peace-time experimental nuclear explosion in the thick salt beds of the Permian Salado formation. Excavation was started July 1, 1960, and completed July 26, 1961. The 10-foot diameter shaft, lined with concrete through the rock section, was sunk 1,216 feet. A drift was driven approximately 1,140 feet on the 1,200-foot level terminating in a shot chamber. On completion of 100 feet of shaft, by means of a truck-mounted crane, facilities were installed for conventional sinking. About 709 feet of rock and 506 feet of salt were encountered in the shaft. Salt beds at this place are reported to be over 1,200 feet thick. The overlying rock section varies greatly in composition and thickness of beds and contains a 28-foot bed of water-bearing dolomite. The aquifer was sealed to facilitate shaft sinking and to prevent water-seepage damage in the salt section of the shaft. Sealing was accomplished by grout injection through holes drilled into the aquifer and by grouting behind the concrete liner.

Jan 1, 1963

By David A. Monaghan

This report describes instrumentation which is part of a system for extinguishing mine fires by pumping material through surface boreholes in order to seal off all underground passageways leading to the fire area. Major instrumentation systems include a closed circuit television probing system and an acoustic seal checking system. The latter consists of a speaker probe, a receiver probe and related signal processing equipment. All probes can be winch-deployed down a 6-inch diameter borehole. The CCTV unit can be rotated 360 degrees in the horizontal plane, and contains sufficient lighting to reliably assay conditions for sealing or rescue within a 200 foot radius. The acoustic seal checker monitors the completion of a seal as it progresses by use of probes lowered through boreholes on either side of the seal.

Jan 1, 1977

By John C. Stankus

To improve mine roof bolt performance, Jennmar Corporation commenced the design and development of a new roof control sys- tem. This new system designated "Insta'l Compression", not only improves safety, but is more cost efficient due to reduced amounts of resin needed per bolt installation. In this paper the research and development of this new system will be outlined. Much of the information presented will be actual test data from various underground operations in Alabama, Kentucky, and Pennsylvania. The development of this system will also cover the design of a new expansion shell, resin compression ring, anti- friction washer, and upgrading of material specifications.

Jan 1, 1990

Mining operations in the Obuasi mine of AngloGold Ashanti Limited began in 1897 using mainly gravity concentration and amalgamation to recover the gold from predominantly high-grade quartz ores. The mine is primarily an underground operation, although some surface mining still takes place. Ore is currently processed by two main treatment plants: the Sulfide Treatment Plant (STP) for underground ore and the tailings treatment plant for tailings reclamation operations. STP was commissioned in February 1994 to treat 180 000 t/m of double refractory gold ore and it hosted the then world's largest commercial scale bacterial oxidation plant which uses Gencor's BIOX« technology. Gold is recovered by gravity and flotation, with the regrinding of the sulfide concentrate before bio-oxidation to liberate locked gold in sulfi de minerals. The BIOX« product is leached using the carbon in leach (CIL) process. Gravity gold recovery is a major component of STP operations and its contribution to overall plant recovery is about ten to 13 per cent. Gravity recovery has undergone series of technological upgrading, since the very first circuit which consisted of a Knelson concentrator and a Gemeni shaking table which was incorporated into the milling circuit at the start of the plant. Presently, each of the gravity circuits which consists of Knelson concentrator(s), cyclones and Gekko InLine Reactors (ILR), are located at the Milling and BIOX« circuits. More recently a new gravity recovery facility comprising of four 48 inch Knelson concentrators and cluster of ten inch cyclones have been incorporated at the tail of the flotation circuit. An additional ILR will be commissioned in 2010 to treat the concentrate generated from the new Semi Autogenous Mill #2 (SAG 2) Knelson: concentrator tower under construction. Since the inception of STP, significant gravity recoverable gold has been recovered via Knelson concentrators and the employed circuits have seen a number of modifications and upgrades, motivated by ore mineralogical changes and recovery concerns. The pioneering adoption of the ILR technology in 2001 and 2003 was a critical factor in enhancing the improved recovery benefit of the gravity circuits. Therefore the objective of this paper is to highlight the mine's experience in the gravity recoverable gold process with emphasis on plant modifications and gravity equipment upgrade. Operational challenges and the contribution of gravity gold to overall plant recovery are also discussed.

Aug 1, 2010

Greater use should be made of lineations in investigations of the engineering properties of rock masses and in structural studies guiding prospecting programmes.A prominent alignment of elongate mineral grains and stretched pebbles usually marks the primary direction in which metamorphic rocks have been extended by flow. In local adjustment zones separating masses that have extended different amounts, this lineation has been a direction of slip. Kinks and crumples resulting from this slip lie in secondary lineation directions transverse to the primary mineral lineation.During deformation relatively mobile materials move into dilatant zones caused by irregularities in primary flow directions. This secondary movement transverse to lineated, primary-flow directions is the cause of crenulations and folds with axes parallel to flow lineations.INTRODUCTIONThe arrangement of inequidimensional particles in rocks is rarely statistically random. Platy minerals tend to be parallel to bedding and foliation planes. Elongate particles and linear structures lie most frequently in certain lineation directions. The types of elongate particles in lineated rocks include needle and blade shaped mineral grains, sheared out segregations, and stretched pebbles, amygdules, and aolites.Crenulations and kinks are the most common of the linear structures involved.Faint lineations are readily overlooked. Even strong lineations have been ignored. This is unfortunate as even weak lineations may be important.Use of lineation information Well-developed lineations influence the mechanical properties of rocks. Quarry workers have long known that the mechanical properties of rock masses vary directionally...

Jan 1, 1965

By Y. P. Chugh

A novel dry and wet air dust filter concept was conceived and demonstrated successfully at two mines. A steel-wool and a fiberglass filter, suitable for underground use were identified through laboratory testing and demonstrated in the mine. The steel wool filter was operated with and without water sprays while the fiberglass filter was only operated in the dry mode. The dry steel wool filter provided a dust capture of 37% at a negligible pressure drop. When fine misting water sprays were used on the steel wool filter, the dust capture increased to 51% again with a negligible pressure drop. The filter screen also remained clean and no change in air flow characteristics was observed as a function of time. The dry fiberglass filter however did not perform as well achieving only 11% dust capture while introducing a significant resistance to air flow. This technology is seen to have several applications in underground coal mines.

Jan 1, 2009

By E. M. Stiles

THE Wellington Lake power plant of the Consolidated Mining and Smelting Company of Canada, Limited, about 25 miles from Goldfields, Saskatchewan, is the second hydro-electric project operating in that Province, the first being the Island Falls plant of the Churchill River Power Company which serves the operations of the Hudson Bay Mining and Smelting Company at Flin Flon, Manitoba. The Churchill River project develops 90,000 h.p. at 56-ft. head; the Wellington Lake plant 3,300 h.p. at 75-ft. with pro-vision for an additional 3,300 h.p. unit. Churchill River power is trans-mitted at 110,000 volts over a 58-mile line of steel towers to Flin Flon and an additional 45 miles over a wooden pole-line to Sherritt-Gordon. Our steel tower-line is 22 miles long, and the voltage is 60,000; this choice be-cause certain such equipment was available from Trail. The diversion of 15,000? second-feet at 56-ft. head for 90,000 h. p. at Churchill river dwarfs our 500 second-feet flow at 75-ft. head for 3,300 h.p. In both cases, the main obstacles to be overcome during plant construction were the lack of transport facilities and the short open season. Let it be noted here that this paper deals mainly with those phases of plant construction which were particularly interesting to the writer. With-out these variations from the ordinary routine, this is just another power project whose story is better told by the accompanying charts and pictures. To many members of the Institute it is still just that; but I am writing for those who, like myself, have been too seldom responsible for major under-rakings at an appreciable distance from a railway siding. When it was planned in early 1937 to erect a 1,000-ton mill at our Box mine, both hydro and Diesel power were discussed. With ten years' ore in sight, even an expensive hydro project, such as ours turned out to be, produces kilowatts materially below the 2-cent operating cost of a Diesel plant using fuel-oil at 14 cents a gallon.

Jan 1, 1940

By Glenn Clarke, Ben Holloway, Barry Lumsden

"BHP-Billiton’s Cannington mine in Northwest Queensland produces a silver-rich lead concentrate and a zinc concentrate. The plant has the capacity to treat 3.1 mta and for the year to June 2006 mean feed grade was 10.3% Pb, 461 g/t Ag and 3.7% Zn. Recovery losses of lead and silver are primarily in the fine fractions. In 2001, the plant was modified when it was determined that splitting the lead feed into two size fractions, and floating the two fractions separately increased fine lead and silver recovery. The fine lead fraction (called the split float) is 80% <16µm and about a quarter of the lead and silver is in the finest fractions. In 2006 to further improve lead and silver recovery a statistical plant trial of magnetic aggregation conditioning of the split float feed was undertaken. While pure galena is diamagnetic the Cannington galena contains iron within the galena mineral resulting in the galena having a paramagnetic, magnetic susceptibility. The trial demonstrated to greater than 98% statistical significance an increase in lead recovery, and to 99% statistical significance an increase in silver recovery, and to greater than 97% significance an increase in the lead in concentrate in the split float circuit. These economic recovery benefits with magnetic aggregation of the split float feed, has led to the incorporation of this technology in the plant.INTRODUCTIONThe BHP-Billiton owned Cannington silver, lead and zinc mine is located in the Australian state of Queensland about 800 kilometres west of the coastal city of Townsville. This is a pastoral area characterised by large cattle farms, low population density and very little infrastructure. The area has two seasons, a wet, hot summer and a dry, mild winter. Because of its isolation and lack of infrastructure the mine has always operated on a fly in fly out basis.Geological drilling defined the resource as 43.8 million tonnes grading 11.6% lead, 4.4% zinc and 538 ppm silver (Walters and Bailey, 1998). At times during its history Cannington has held the crown as the single largest lead and silver mine in the world (Torrisi and Smith 2003). Another unique characteristic of the operation’s history is the rapid progress from discovery to operation. The first drill to intersect the ore body was in 1990 and the mine and plant was commissioned in 1997."

Jan 1, 2008

By Krzysztof Kotwica

The steady demand for rock materials leads not only to on increase in mining but to the need for decreasing the loss of material in the process of exploitation as well. It brings about an increase in using of explosives in open pits and as a result an increase of after blasting gases volume, vibrations, the scattering (dispersion) of stone ect. All these factors affecting the environment lead to the research work for applying the electrohydrodynamic methods both in open casts and underground mines. In the article the authors describe the concept of this method and construction of equipment which recently have been successfully introduced in mining, the results obtained determine the possibilities of using this method and the future directions. The results of combined method with high-pressure water jets cutting and prototype equipment for separating rock blocks from the rock mass using special head with high-pressure water jets are also described.

Jan 1, 2006