Search Documents

By A. Takala, B Nielson, J. Schunicht

"Pre-concentration in minerals processing presents clear advantages in energy efficiency, water efficiency, reduction of consumables and minimization of capital and operating costs. Outotec’s sorting solutions are powered by Tomra Sorting in order to achieve pre-concentration of concentrator feed in a variety of mineral processing applications. Sensor based sorting combines advanced sensors with rapid computational evaluation and mechanical separation of valuable material from waste and/or gangue. Modern sensor based sorting machines typically use fine air jets to propel individual rocks, thus optimizing recovery and minimizing “mis-sorting”.Gold is generally present in such low concentrations that sensors suitable for ore sorting cannot directly detect it. Therefore, in order to sort gold ore, properties of associated host rock are used. Free and sulphidic gold is often hosted on the quartz-host rock contact zone. Laser scattering effect can be used to detect the surfaces of quartz and composite quartz-host rock particles for subsequent sorting with very high recovery of 95 to 99%. In addition, ore often preferentially fractures along the quartz-host rock contact zone in the crushing circuit. This behavior helps because it liberates more quartz for detection.The feasibility of sorting is investigated for four gold projects in Northern Europe with similar mineralogy. This includes geometallurgical evaluation, amenability testing, small scale “mini-bulk” factory testing in full scale sensor based sorting. The results of the various tests are presented and basic feasibility demonstrated with information on flow sheet development. In addition, the amenability process is evaluated and recommendations made for future projects."

Jan 1, 2017

Experimental Mine, Val d'Or, Quebec, Experiments on the ignition of sulphide dust clouds by explosives have been conducted in a 1 m3 explosion chamber. The explosives tested are ANFO, emulsion, aluminized emulsion and Detasheet. By controlling the composition of the ANFO and the emulsion explosive the oxygen balance could be changed in order to identify the dominant factors in the ignition of sulphide dust clouds by explosives. Experimental results, combined with theoretical calculations, show that the temperature of the detonation products is the most important parameter in the ignition of the dust cloud while the combustible detonation products are of secondary importance in the case of non-aluminized mining explosives. In the case of aluminized explosives and explosives having very negative oxygen balance the ignition of the dust cloud is assisted by the large amount of combustible detonation products.

Jan 1, 1993

By G. Styles, K. Lye, R. Tenbergen, M. Mayhew

Requirements to produce a higher bulk concentrate grade have necessitated extensive use of on-stream analyser data and computer programming to obtain the targets set for Frood Stobie Mill as required by overall milling considerations.A brief history of milling process changes associated with the changes from a low grade (3% Ni) bulk concentrate in the sixties to a high (6 to 8.5%). Nil bulk concentrate currently will be presented.The heart of the presentation will be the computer control schemes for ""self optimisation"" of the distinct flotation sections in the plant within certain restraints to achieve targets set by the mill metallurgist.

Jan 1, 1985

By R Ballantyne, M Adams

Time Usage Models, used as a basis for calculating performance indicators for mobile mining equipment, have developed from very simple to very sophisticated models. This development has paralleled the increased collection and analysis of production data that itself has been enabled by the evolution of underground voice and data communications along with the relevant information systems. A Time Usage Model divides the hours that equipment is (or is not) used into standard components, by a hierarchical breakdown, so that measures of productivity can be used to compare performance of both people and equipment. The calculation of equipment availability, and thus the underlying Time Usage Model, has always been an extremely emotive topic as different groups use time usage information for different purposes. The direct link between measuring performance Key Performance Indicators (KPI) calculated from these models and employee rewards impacts upon the workforce. This paper discusses the conflict in use by various stakeholders and proposes ways to address some of the more contentious issues each supported by case studies. The simple status code functionality used by early systems has proven inadequate, leading to the evolution of “work-arounds”. These workarounds have become the norm and unfortunately have become embedded in the next generation of models and the information systems that incorporate them. This paper contends that the industry should stop building Time Usage Models to accommodate shortcomings in proprietary systems, but rather collaborate with suppliers to develop innovative methods to deal with the fundamental requirements. There are many points of differentiation that are not clear-cut. Pitfalls are discussed as well as threats to success. A framework of rules is developed as guidelines for how a Time Usage Model should be developed and applied. This will hopefully stimulate the on-going discussion as to how Equipment Availability and other components of the model should be calculated.

Mar 15, 2021

By E. D. Calvert

The objective of this research was to examine variations in melting and forging practice for four titanium-base alloys and to determine their effect on the resultant product. Of particular interest was the evaluation of the skull-casting technique. The data should serve as a guide to producers and consumers of titanium products. Physical properties of four titanium-base alloys in ingot form and in sheet form were evaluated and correlated, where possible, with variations in the melting and casting procedure. Consumable-electrode melting was used throughout, but arc current and furnace backfill pressure were varied, and ingots were formed both by melting directly into a water-cooled copper mold and by skull melting followed by pouring into a graphite mold. Alloying metal additions for the alloys tested were (1) 8 percent manganese, (2) 6 percent aluminum and 4 percent vanadium, (3) 6 percent molybdenum and 2 percent aluminum, and (4) 16 percent vanadium and 2.8 percent aluminum.

Jan 1, 1962

By Thomas M. Gurtowski

The New Pacific Northwest Baseball Park, now known as Safeco Field, is located directly south of the Kingdome in Seattle, Washington, and will be the new home of the Seattle Mariners baseball team. The location of the ball field is shown on Figure 1, Vicinity Map. The seating capacity is 45,600, and outfield distances are 331 feet in left, 405 feet in center, and 326 feet in right field. The overall dimensions of the stadium are 680 by 800 feet. It is bordered on the east by the Burlington Northern Santa Fe Railroad main line. A unique aspect of this ballpark is the retractable roof with a north-south span length of 660 feet. The roof consists of three separate sections that roll on elevated rails running east-west on the north and south sides of the stadium. The soil conditions consisted of near-surface fill underlain with alluvial and Estuarine deposits to depths of 60 to 80 feet. The bearing soils consisted of very dense, glacially overridden deposits. Groundwater is 4 to 7 feet below the ground surface, and the alluvial deposits are subject to liquefaction during a strong motion earthquake.

Jan 1, 1998

By D P. Murphy, R F. Dewhirst

Traditionally closure has been seen by the Resource sector solely as a green or an environmental issue, focused primarily on the requirement to rehabilitate the site following cessation of production activities. In addition to operational, maintenance and production aspects of processing plant design, future design teams will need to take a more holistic view and consider an increasing number of sustainability issues including safety in design and cleaner production as well as closure itself. Sustainability principles being adopted by industry such as the Minerals Council of AustraliaÆs Enduring Value Framework are now broadening our understanding of closure. While issues around the closure of tailings dams and associated infrastructure have been widely studied, few investigations have looked closely at the implications of closure on the design of minerals processing plants. It is likely that design teams may be able to make a significant contribution to meeting industry objectives by adopting innovative designs which, in addition to meeting production objectives, deliver sustainable and cost effective plant closure outcomes. This presentation explores the opportunity for innovative design of mineral processing plants through the assessment of alternative closure objectives. This assessment specifically looks at current industry standards and statutory requirements, as well as potential risks and opportunities associated with each objective. Alternative design strategies to meet these objectives are discussed.

Jan 1, 2006

By K. S. Lackner, T. M. Yegulalp

We present a review of research and development for coal based clean energy systems aiming for zero emissions to the atmosphere. These systems can utilize all kinds of coal or other solid carbon sources such as tar sands as well as liquid hydrocarbons. The chemical energy of carbon is transferred to hydrogen and used in power generation, in fuel cells, or hydrogen combusting turbines. The waste products of these future power-generating systems are ash, sulfur compounds and CO2. We also summarize current and developing technologies for processing of CO2to produce mineral carbonates for permanent disposal, and associated byproducts.

Jan 1, 2003

By Ziyad Abunada, David O’Connor, Abir Al-Tabbaa

"Abstract Contaminated land remediation using soil mix technology (SMT) is a relatively recent development which has been shown to be a cost effective and versatile system with numerous environmental advantages over other remediation techniques. The added complexities and variability associated with contaminated sites has escalated the need for field trials, field monitoring and specific QC measures to be undertaken for this setting and was the rationale behind project SMiRT (Soil Mix Remediation Technology). The main aim of project SMiRT was field validation, testing and assessment to provide stakeholder confidence in SMT and increase its uptake for land remediation in the UK. The field trials involved the treatment of 800 m3 of soil, through applying six different remediation techniques with four different SMT systems and introducing over thirty binders and binder compositions with a range of installation methodologies. Various issues were faced during the installation process and which were addressed on site. This paper presents some aspects of early age field observations, field monitoring, in-situ testing, coring and laboratory testing of cored samples and highlights some lessons learnt, providing valuable information on the issues that need to be addressed for this application of SMT.IntroductionAlthough soil mix technology (SMT) was developed in the 1960s in Japan and Sweden for geotechnical applications, its potential in geo-environmental applications became evident more recently the 1980s in the US and in the 1990s in Europe, having since increased to provide a range of remediation systems (Al-Tabbaa and Evans, 2003; Al-Tabbaa et al., 2011). The most common applications to date have been (a) the construction of low permeability containment walls or cut-off walls to contain a contaminated site; (b) stabilisation/solidification (S/S) treatment, with cementitious binders, for physical and chemical encapsulation of contaminants in soils and (c) the installation of permeable reactive barriers (RPBs), which are permeable walls that intercept the groundwater flow and remove contaminants from it, by mixing special additives with the native soil. Contaminated land remediation using SMT is a cost effective and versatile approach with numerous technical and environmental advantages over other remediation techniques. These advantages include the use of simple and well established techniques and equipment, speedy implementation, applicability to sites of any size and to multiple contaminants, elimination of off-site disposal, low risk and low emissions. There is a lack of competing alternative technologies that offer the same level of versatility and economic, environmental and social benefits, under current environmental legislation constraints. In addition, most currently available contaminated land remediation techniques are only partially effective, and are relatively contaminant-specific. This makes SMT a promising and timely contender to lead the market place in offering a cost-effective, efficient and low risk solution to contaminated soil and groundwater remediation and has resulted in a range of recent innovations."

Jan 1, 2014

By C. Scheffer

This paper describes a model that can simulate the behaviour of a pneumatic intensifier that is generally referred to as an ?air pump? (AP). The AP is used in many South African underground mines, and utilizes compressed air with pressures between 0.3?0.6 MPa to pump water up to pressures of 12?18 MPa. The high pressure water is used in numerous underground mines to pressurize props and roof bolts that act as safety and roof support devices. The simulation model reproduces the intensifier's operation under various conditions and therefore can be used to investigate the AP's sensitivity towards environmental conditions, design parameters (such as spring stiffness, plunger diameter, nozzle diameter etc.) and operating conditions. Model validation by comparison with laboratory experiments showed good correlation. The model can subsequently be used to investigate design changes aimed at improving the AP's performance and reliability over a wider range of operating conditions.

Jan 1, 2005

By Desiree Willis

One of New York City?s largest subway projects is under way 43 m (140 ft) beneath the surface of downtown Manhattan. The East Side Access project, more than 30 years in the making, was halted after a partial excavation in the 1970s due to a lack of funding. The project, once dubbed the ?Tunnel to Nowhere,? has been revitalized into a groundbreaking subway line that includes unique tunnel boring machines (TBM), construction methods and muck removal systems. Project overview The East Side Access project involves construction of a new 6.7-km (4.2-mile) subway line needed to relieve heavy traffic congestion between the boroughs of Queens and Manhattan. The line will serve approximately 160,000 commuters daily between Grand Central and Sunnyside rail stations. Manhattan and Queens will be connected under the East River by the 63rd Street tunnel, a submersed double-decker tube. The submersed tube consists of reinforced concrete sections barged in place on the riverbed. The tube contains operational subway lines on the top deck, while the bottom deck (the ?Tunnel to Nowhere?) will become operational when the East Side Access project is completed in 2013.

Jan 1, 2008

By T. Proietti, L. Mongiovì, L. Simeoni

Reliable estimates of the kinematic characteristics of movements are obtained by using a statistical model SSM. This model represents a useful tool for the management of alert and alarm systems. L'élaboration des données du déplacement médian d'un modèle statistique SSM opportun fournit des estimations fiables des caractéristiques cinématiques du mouvement. Le modèle peut être ainsi utilisé pour la gestion des systèmes d'alarme. Die Bearbeitung von Bewegungsdaten anhand eines geeigneten statistischen Modell SSM ergibt vertrauliche Abschätzungen der kinematischen Eigenschaften der Bewegung. Das Modell kann also für das Management von Alarmsystemen verwendet werden.

Jan 1, 2003

As part of the Bureau of Mines program for conserving domestic mineral resources, a survey was made of the methods used for identifying scrap metals. Because of the large number of alloys currently being scrapped, correct identification of these materials is essential if they are to be recycled effectively. The methods and instruments used to identify scrap metals are described and evaluated. These include object recognition, color, density, magnetic testing, spark testing, chemical spot testing, thermoelectric measurements, eddy current measurements, and elemental analysis by chemical and instrumental methods. Other potential techniques are discussed also.

Jan 1, 1982

By L. E. Djingheuzian

Introduction For many years the immense deposits of bituminous sands of northern Alberta have been attracting the attention of our governments, engineers and .scientists ( 6). Undoubtedly these bituminous sands represent one of the greatest potential resources of liquid fuels in the world. However, their commercial development has been retarded by the complexities of the technological problem and by the economic factors involved in the processing of the sands. The technological problem has been attacked from several angles ( 2, 3, 1, 11), and cold water separation of bitumen is one of them. To the ore dressing engineer, the cold water process is of utmost importance since, by the use of standard ore dressing machinery, it accomplishes most efficiently and economically the separation of bitumen from bituminous sands. The significance of using ore dressing equipment was especially enhanced by the fact that the scientific principles which underlie the design of standard machines were demonstrated in the cold water separation process with an extraordinary clarity. This greatly facilitated the analysing of limitations and advantages of different machines during-the pilot plant investigations and helped to complete the investigations practically in the allotted time.

Jan 1, 1952

By A M. Ebbels, D Pratt

The current commodities super-cycle has seen an explosion in the number of mining projects demanding human resources throughout the world. The demand for key personnel currently far outweighs the international talent pool and will take several years to subside. A highly effective project team can be the difference between a successful project and a bad public relations exercise. Building an effective team and retaining the team members has become one of the major influencing factors for successful project development in the mining industry in the last decade.Increasingly, international teams are being established combining skill sets, subject matter experts, unique previous experiences and diverse cultures to deliver mining projects all around the world.This paper explores the characteristics of a highly effective team, the communication and geographic challenges and some potential pitfalls which influence the ability to form effective teams within the mining industry.CITATION:Ebbels, A M and Pratt, D, 2012. A great project team - Bringing together location and culture, in Proceedings Project Evaluation 2012 , pp 197-202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By H. Michael Breza

Texasgulf Inc. installed bucketwheel excavators and overland conveyor sysems at its Aurora, NC phosphate mine o increase the productivity and flexibilty of the surface mining operation. This ;ystem has significantly improved overrall. Its flexibility is evidenced by adapation to operation requirements, such is mining area moves, movement of xcavated overburden to designated ites, selective handling of overburden, poll placement contouring, and proiding an environmentally sound and afe operation. The system's productiv:y is evidenced by case studies relating. overall production, excavation rates nd cost-effectiveness. There are many competing alternaves available for excavating uncon)lidated overburden: truck-shovel, raglines, dredges and bucket wheel ticavators. These alternatives also may used in tandem to recover reserves icated at greater depths.

Jan 1, 1993

By F. H. Buchella, J. F. Buchanan

The San Manuel copper deposit is located about 45 miles northeast of Tucson. The concentrator, smelter, administration building, and other plant facilities are located about seven miles southeast of the ,nine area at the new town of Sari Manuel as shown on Figure 1 (Sketch).

Jan 1, 1961

By S. M. Shelton

Ferrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced; although it is well-known that there are largo deposits of low-grade ore in the United States, production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stock piled ore is depleted through inability to obtain adequate supplies from foreign sources. Consequently, a program of laboratory and pilot-plant investigations designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines. This paper is one of a new series that will include reports of results obtained in the various investigations conducted under the manganese program. The scope of the program and the organization that was set up to direct and supervise the work were discussed in the foreword of the first paper of this series, Report of Investigations 3506, Manganese Investigations 1. Concentration of Manganese Ores from the Drum Mountain District, Utah, by S. R. Zimmerley, J. D. Vincent, and C. H. Schack. Other reports will be published as the work progresses.

Jan 1, 1942

By S. J. S. Ferreira

Anglo American Platinum's Khomanani 2 shaft changed over from down-dip mining to breast mining in 2004. The changeover was made to ensure that production targets were met, as it was said that predevelopment for down-dip mining was not fast enough to sustain the required ore reserves; nevertheless, production performance did not increase as expected. In this study a trade-off was performed between down-dip mining and breast mining on the Merensky Reef at Khomanani 2 in order to find the most suitable method for mining the Merensky Reef. Data was gathered by means of a literature survey, underground observations, and interviews with personnel as well as data from various departments on the mine. The two mining methods were studied and then evaluated in terms of the following criteria: safety, mining rate, cost and other factors which were identified as the main drivers of the mine. A scaling system was used to rate the performance of the two mining methods. Analysis of the results shows that down-dip mining and breast mining have the same safety performance ratings. Breast mining has a better mining rate performance than down-dip mining. Breast mining was found to be costly in comparison with down-dip mining, which has a good cost performance rating. The overall ratings of the two mining methods are very similar, with down-dip mining achieving a rating of 76 and breast mining 75.5 out of an optimum 102. Khomanani 2 currently practices breast mining, and with such a slight difference in performance rating between the two methods, it will not be worth changing over to down-dip mining as production is likely to be adversely affected during the changeover. Down-dip mining does, however, have potential for improvement in its performance rating. Further studies focusing on the improvement of the mining rate performance for down-dip mining are needed to see if this potential can be realized. If significant improvement can be made in the performance rating for down-dip mining, a changeover to down-dip mining can be reconsidered.

Jan 1, 2012

By Travis Q. Lyday

During 1983, Ecuador's gross domestic product (GDP) decreased by a reported 3.3% in real terms, the second consecutive decline in the economy after more than a decade of growth generated mainly by petroleum export revenues. The slowdown was due, in part, to the effects of the world recession, lower foreign demand for oil, depressed world oil prices, and reduced demand and prices for Ecuador's traditional agricultural exports. Inflation accelerated to an estimated 55% annual rate. The sucre was devalued in March, for the second time in less than a 12-month period, by 27% after remaining unchanged during the previous decade. In addition, continuous adjustments were made every weekday, effectively devaluing the sucre another 30% by yearend. Ecuador's production of crude petroleum increased almost 12% in 1983 compared with that of 1982. Average daily production was 237,100 barrels per day (bbl/d), up from 211,300 bbl/d in 1982.

Jan 1, 1985