Search Documents

By Pengfu Tan

Xstrata Copper at Mount Isa in Australia has operated one copper Isasmelt furnace and four P-S converters. The phenomena of foaming occur in above 10% of converter operations. A thermodynamic model of copper P-S converter and a viscosity model of converter slag have been developed to simulate the slag blow and copper blow. The model predicts the chemistry and viscosity of copper skims during copper blow. The effects of oxygen potential, charge of dirty materials, slag carry-over, under-blowing, over-blowing, and temperature on the foaming and viscosity of copper skims have been discussed. Some improvements of the industrial operations have been presented.

Jan 1, 2006

By J. Stacho, Frankovská. J.

"Abstract The use of continuous flight auger (CFA) piles in Slovakia has increased significantly in recent decades. High-rise building of administrative centre Lakeside Park in Bratislava is based on piled-raft foundation. The technology of CFA has been used due to the advantages of this technology in comparison with driven and bored piles in local geotechnical conditions. Piles have been designed in accordance with Eurocode 7. Resistance of piles was calculated by using an analytical calculation model for bored piles according to Slovak technical standard and CFA technology has been taken into account by coefficient equal to 1.1. Settlement of piles was calculated by using a calculation model which is being used in Czech Republic and Slovakia. Two well instrumented static load tests were carried out to verify the pile design. The results of static load tests showed that the design was conservative. The paper presents analysis of numerical modelling of CFA pile and static load tests. Load-settlement curves and load distribution curves over pile shafts are compared. Software Plaxis 2011 has been used for numerical modelling. Hardening soil model allows considering over consolidation of Tertiary Silts and water pressure in deep sandy lenses. The article also presents the parametric study where the influences of pile-soil interface reduction factor, over consolidation ratio and material models of soils are analysed. The results of numerical modelling showed that the most appropriate results have been obtained when the interface reduction factor equal 0.9 and real behaviour of groundwater were considered. The conclusion of the paper confirms that mechanical behaviour of the ground can be better understood and determined by using FEM than analytical methods.1. IntroductionPiles are among the most frequently used elements of deep foundations. Piles transfer loads down to a suitable bearing stratum when the soil immediately below a construction is unsuitable. Piles are also used to reduce settlement of structure. At present, the requirements of limit settlement of structures are more stringent. Examples of these structures are commercial and administrative centres that form a complex of different tall buildings. High-rise buildings cause greater contact stresses than connected low-rise buildings. Pile foundations in such cases should be placed under the high-rise buildings to achieve an appropriate settlement.Resistance of piles can be determined from static load test results, in-situ tests and empirical experiences or calculations. Static load tests give the most reliable results, but these tests are also the most expensive. This is the reason for constant development of computational methods. Especially numerical methods give more accurate results by using more sophisticated material models e. g. hardening soil or hypoplastic model."

Jan 1, 2014

By Virgil Marple

In the summer of 1979 the University of Minnesota Mobile Laboratory (UMML), designed for the analysis of airborne particles and gases was used to study fugitive dust from an open pit coal mine. The analysis consisted of determining the particle size distribution and concentration of dust from various mining operations, such as blasting, draglines, loading, roadways and bottom scrapers. For some operations the particles size distribution and concentrations were determined at varying distrances. Details of the dust concentration within the plumes as the plume passed the UMML were measured with an optical particle counter. For line sources, such as roadways this enabled the calculation of the particle flux at the sampling location. In addition to the standard instruments associated with the UMML, the applicability of some new instruments were investigated. These included a uniform deposit cascade impactor and a flux meter. Finally, a technique in identifying plume origins which utilized elemental X-ray flourescence analysis of filter samples was shown to be effective.

Jan 1, 1980

By P. J. Mackey

New and emerging, as well as proven technologies for the smelting of copper, nickel, lead and zinc are briefly reviewed. The number of new technologies available today is greater than at any time in the past, and interest and development activities remain high despite the economic dif-ficulties faced by the non-ferrous metallurgical industry. Part of the impetus is provided by the realization that only the most cost effective producers will remain competitive, and that new technology is one key to cost effectiveness. The commercially proven "new" copper smelting processes can now be considered to be conventional- technology, and are expected to dominate copper smelting for acme time. There is a growing. interest in continuous copper converting, although direct smelting and converting to copper in one vessel remains the- ideal. There is little activity in nickel smelting. After many years. of development, it appears that several new direct lead smelting processes will soon be a commercial reality. The electrolytic zinc process is expected to continue its dominance, although there is a renewed interest in pyrometallurgical approaches. One of the new zinc processes, and a molybdenum smelting process, illustrate the possibilities of using plasma technology in non-ferrous metallurgy. In the area of complex sulphides, there is perhaps less interest in the treatment of bulk con¬centrate, and more in the treatment of so-called dirty copper concentrates. Much of the technology ancillary to smelting has remained relatively unchanged, and more effort must be made to advance the technology in areas such as materials handling, gas cleaning and sulphur fixation, and energy recovery. More attention to engineering design is also needed. Escalating capital costs may make mini-smelters attractive, but imaginative technology and innovative engineering will be required to make them cost effective. Finally, a glimpse is offered of the smelter of the future.

Jan 1, 1983

By H. Dong

This paper presents a heat conduction model to determine the erosion profile of freeze linings in a ferronickel submerged arc furnace. Kirchhoff transformation was adopted to simplify the nonlinear equation governing heat conduction. The boundary element method (BEM) and Nelder-Mead simplex optimization method were employed to solve an inverse heat conduction problem. Erosion profiles could be obtained when calculated temperatures at sensor locations agreed well with measured temperatures. The model was validated by comparing the heat loss through the linings, which was calculated by BEM and integral operation after erosion profiles were obtained, with the value calculated from industrial data such as actual power consumption, tap-to-tap time, and ferronickel output. The optimal solution for the erosion profile could be acquired when the difference in heat losses calculated by these two methods is at a minimum.

Jan 1, 2014

By J. M. Davidson, F. Fraas, J. E. Conley

"A number of Reports of Investigations pertaining to the extraction of potash from cal¬cined polyhalite have been made by various members of the Nonmetallic Minerals Experiment Station of the United States Bureau of Mines. These reports describe results obtained in the study of samples of polyhalite (2CaS04.K2S04.MgS04.2H20) from deposits of possible com¬mercial importance in Texas and New Mexico.3Storch and Clarke6 in their initial paper presenting data on the properties of Texas polyhalite demonstrated the desirability of calcination and subsequent hot extraction with water as a satisfactory pronedure for treatment of this potash-bearing salt. Their preliminary data have been supplemented by an additional report7 dealing more particularly with the leaching of raw and calcined polyhalite with water and with saturated sodium chloride solu¬tions. Further data8 have been reported as a result of experiments made in a small labora¬tory rotary-tube furnace under various calcination and extraction conditions. Hot water was used as the leaching solution in all of these tests.In addition to the data on calcination and extraction, two processes as proposed by Storch and Clarke have been published by Wroth,9 and more recently a number of very promising processes have been proposed by Storoh and Fragen.10"

Apr 1, 1932

The ERMS Process was developed during four years of testwork by Austpac Gold NL to overcome the severe metallurgical problems of the ilmenite atWestport, in the South Island. These deposits have been known for about one hundred years. They were originally mined for gold, and only later attracted attention as a possible source of titanium minerals.   The resource is of world scale and may exceed 20 million tonnes of contained ilmenite. Similar deposits occur at Barrytown further south and together these areas would constitute an important opportunity for export-oriented mineral development, if a viable beneficiation technology were available. Further processing is essential, as the composition of the ilmenite is well below market specifications.

Jan 1, 1993

By G. Richard Dreese

Most coal mining states have passed or amended laws restricting strip ruining in the past two years. In light of this and in anticipation of further restrictions by the states and the federal government on strip mining this paper attempts to show the Impact of these new laws on the structure of the coal mining industry in Ohio and specifically on one small stripping firm in Ohio. The implications of the study are applicable to other states under similar circumstances and to other industries which are being caught up in the ecological-economic struggle.

Jan 1, 1973

By Pravin Mathur

"Praxair's CoJet® technology was introduced in 1997 to effectively inject chemical energy in electric arc furnaces. Coherent jets were invented as a revolutionary means of injecting oxygen and other gases into the EAF and into converters. Today, steel makers have widely accepted this concept in over 70 EAFs worldwide. Indeed, the whole industry has shifted to this new standard for chemical energy input in EAFs. CoJet® technology has also been implemented successfully in BOF converters.This paper will review the principles of coherent jets as applied to steelmaking. The key learnings garnered from several furnaces are also reviewed. In addition, while the CoJet® program has been widely accepted worldwide, based on steady feedback received from customers and the market place, several programs are underway in development and commercialization. These enhancements and new applications of CoJet® technology are also overviewed in the paper."

Jan 1, 2004

These proceedings consist of papers presented at Bureau of Mines Technology Transfer Seminars in December 1983 for the purpose of disseminating recent advances in mining technology in the area of mine ground control. The Bureau of Mines conducts several of these seminars each year in order to bring the latest results of Bureau research to the attention of the mining industry as quickly as possible.

Jan 1, 1984

By Susanne Hering, Brent Kirby, Charles D. Litton, Tracy Allen, Kirk R. Smith, Rufus Edwards

In developing countries, high levels of particle pollution from the use of coal and biomass fuels for household cooking and heating are a major cause of ill health and premature mortality. The cost and complexity of existing monitoring equipment, combined with the need to sample many locations, make routine quantification of household particle pollution levels difficult. Recent advances in technology, however, have enabled the development of a small, portable, data-logging particle monitor modified from commercial smoke alarm technology that can meet the needs of surveys in the developing world at reasonable cost. Laboratory comparisons of a prototype particle monitor developed at the University of California at Berkeley (UCB) with gravimetric filters, a tapered element oscillating microbalance, and a TSI DustTrak to quantify the UCB particle monitor response as a function of both concentration and particle size and to examine sensor response in relation to changes in temperature, relative humidity, and elevation are presented here. UCB particle monitors showed good linearity in response to different concentrations of laboratory-generated oleic acid aerosols with a coarse (mass median diameter, 2.1 µm) and fine (mass median diameter, 0.27-0.42 µm) size distributions (average r2 = 0.997 ± 0.005). The photoelectric and ionization chamber showed a wide range of responses based on particle size and, thus, require calibration with the aerosol of interest. The ionization chamber was five times more sensitive to fine rather than coarse particles, whereas the photoelectric chamber was five times more sensitive to coarse than fine. The ratio of the response between the two sensors has the potential for mass calibration of individual data points based on estimated parameters of the size distribution. The results demonstrate the significant potential of this monitor, which will facilitate the evaluation of interventions (improved fuels, stoves, and ventilation) on indoor air pollution levels and research on the impacts of indoor particle levels on health in developing countries.

By Donald Leroux, Dave Scott, Giovanni Di Prisco

"The Lady Loretta lead-zinc deposit in Northwest Queensland, Australia contains an average of 5.9% lead, 17.1% zinc and 97 g/t silver. Ore mineralization is mostly comprised of fairly complex intergrowths of pyrite, sphalerite and galena. Starting in 1998, Noranda Inc., the major joint venture partner of the project, conducted extensive metallurgical test work, which culminated in July - August 2000 in a series of Pilot Plant tests. A common thread to all the metallurgical work has been the deportment of a large portion of silver into non-payable metallurgical products. Average silver distribution from four Pilot Plants shows a distribution of silver in lead concentrate of 28%, whereas silver in zinc concentrate was 49%, and 23% in the final tails.The consistently poor silver recovery as well as the fairly unusual silver distribution, particularly in zinc concentrate, was considered an issue to be thoroughly investigated. A mineralogical plan was devised to determine if these particular metallurgical results were somewhat related to the nature and mode of occurrence of silver carriers. Work was performed to determine discrete silver-bearing minerals and/or silver contained in solid solution in a suite of commonly occurring sulphides. Ore microscopy, SEM methods, Electron Microprobe and Ion Microprobe analyses were all used to answer these questions, and to find the silver carriers, so a metallurgical plan could be devised to improve silver recovery.INTRODUCTIONPotential economic exploitation of the Lady Loretta deposit in Queensland, Australia is driven by revenue derived from zinc and lead flotation concentrates and co-product silver recovery in lead. Relatively low recoveries of payable silver to lead concentrate, and high silver distribution to zinc concentrate necessitated an investigation into the natu"

Jan 1, 2002

By George S. Rice

"""To prevent the propagation of mine explosions, the Bureau of Mines, Department of Commerce, recommends rock-dusting all coal mines, except anthracite mines, in every part, whether in damp or dry condition. It also recom¬mends that rock-dust barriers be used to sectionalize the mine as additional defense; but these should not be regarded as a substitute for generalized rock-dusting."" (Mine safety decision, No. 5, April 7, 1927.)The purposes of this circular are to present concisely the requirements for effective rock-dusting of coal mines in order to prevent propagation of mine explosions, and to point out the principal related facts on explosibility of coal dusts and mixed coal-mine dusts, as determined by extensive testing in the Experimental Mine of the Bureau of Mines. study of these principal facts on coal-dust explosibility in conjunction with the recommendations for rock-dusting, should help to make clear to mine operators and others concerned the necessity for systematic rock-dusting in all coal mines except anthracite mines, and the futility of inadequate or sporadic rock dusting.The descriptions of nearly 1000 explosion tests in the Experimental Mine are available in a forth-coming bulletin2 and in earlier publications.3For detailed specifications as to the kind of rock-dust, amount to use, where to be applied, and method of sampling and testing, the reader is referred to Bureau of Mines Serial 26064, and American Engineering Standard Committee ""Recommended American Practice for Rock-Dusting Coal Mines"" quoted in Bureau of Mines Information Circular No. 60305.Summary of Specifications for Rock-Dusting1. Mines to be rock-dustedAll coal mines, except anthracite mines, should be rock-dusted.2. Extent of rock-dustingAll open accessible parts of a coal mine should be rock-dusted, including slopes, entries, cross,-cuts, and rooms, headings and pillar workings to within at least 50 feet of the face.3 Amount of rock-dustingAfter cleaning up the coal dust as thoroughly as practicable, sufficient rock-dust should be used to have the mixture of remaining coal-dust plus the rock-dust in any zone contain 65 per cent or more of inert or noncombustible matter. First dusting may require 3 pounds to 5 pounds per linear foot of passageway.4. When to rock-dust In any zone or section (made by dividing the mine for rock-dusting purposes) when the incombustible content falls to 55 per cent, that section should be re-rock-dusted so as to bring the incombustible content well above 65 per cent."

Jun 1, 1927

By C. Guo

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd oil sands plant. Over the past years (since 1997), there has been a marked change in the consolidation behaviour of MFT in the MLSB, which is attributed to microbial activity. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. In certain regions within the MLSB, gas bubbles are released to the water surface of the tailings pond. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings). This phenomenon contradicts the consolidation models for MFT developed over the past 20 years. The above phenomenon has also been reported at the oil sands tailings ponds operated by Suncor Energy Ltd. in Fort McMurray. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. The rapid densification of the MFT may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program is underway to study the mechanism leading to the rapid densification phenomenon. Systematic field investigations were performed to determine the distribution and characteristics of the rapidly densified MFT. Gas bubble distribution on the water surface was mapped to determine the zones of different biological activities in the pond. These field investigations provided solid ground for further experimental and theoretical research. A number of small-scale column tests were carried out to observe the gas evolution and to measure the changes of some geotechnical parameters under different microbial activity. Also, a series of gassy MFT densification tests are being conducted to study the mechanism of the rapid densification of the MFT under microbiological activity. A review and discussion of the research program is given and some preliminary research results are presented in the paper.

Apr 1, 2005

By J. R. Ross

Techniques for recovering scandium from uranium plant iron sludges and from wolframite concentrates are described. The best procedure found comprised (1) dissolution with sulfuric acid, (2) preliminary concentration by solvent extraction with a primary alkyl amine, (3) further enrichment and purification by a combination of ion exchange, solvent extraction, chemical precipitation, and calcination. Recovery of scandium from these raw materials, which contained 0.058 and 0.14 percent scandium, ranged from 83 to 90 percent in products analyzing 99.6 to 99.9 percent scandium oxide.

Jan 1, 1965

By J. C. Osmond

One of the least known geologic regions in the U.S. is the area now called the Basin and Range Province. It is paradoxical that so little geologic information has been compiled for a province that has yielded billions of dollars worth of metals and is currently producing a small amount of oil. Regional stratigraphic studies of parts of this large territory have been published only recently, and regional structural interpretations of even parts of the province are rare in the literature. This, of course, does great injustice to the earliest workers: Gilbert,1,2 Russell,9 Le Conte,4 Spurr,5 Louderback,8 and others, who recognized the area as distinctively different from the rest of North America. Their simplified picture of the structure of the ranges and the province as a whole is the groundwork for present understanding and has never been superseded. Since their early works, however, geologic data from the province has consisted largely of detailed reports of widely scattered mining districts. Each district has been described as though it were an island in an unknown sea. More recent syntheses of the geologic history have been prepared by Lindgren,7 Ransome,8 Nolan,9 Bill-ingsley and Locke,30 Longwell,11 and Eardley.12 The tentative nature of the present interpretation, which treats the structural evolution of the Utah and Nevada area, must be considered in light of the scarcity of geologic information from the province as a whole. The methods of interpreting tectonic history from stratigraphy are based largely on the concepts of Marshal Kay.23 Discussions with Hoover Mackin also have aided in organizing the Tertiary history. TECTONIC AND STRATIGRAPHIC SETTING Two approaches to the subject of the tectonic history are possible; they correspond to looking through opposite ends of a pair of binoculars. One involves an expansion and extension of detailed work and the other an interpretation based on regional geological relationships. It is believed that the second approach, used here, is not in disagreement with detailed observations. The area of the Basin and Range Province is shown in Fig. 1. Within this area middle Tertiary to Recent high-angle faulting has controlled development of mountain ranges and valleys. Only the part of the area north of Las Vegas, Nev., and south of the Snake River in Idaho will be considered in this article. Within this part of the province most of the ranges trend north-south. Approximately two thirds of the area is covered by late Tertiary to Recent valley fill and lake deposits.

Jan 1, 1961

By Donald O. Downing

"IntroductionThis paper provides an overview of the coal mining industry in Canada with a description of current circumstances. The Canadian industry is placed in a global context and the future prospects of the industry are described. The export market is very important to the future of Canadian coal production and the essential aspects of the market are explained. Future prospects are very much tied to metallurgical coal exports and some key characteristics of that market are discussed, including major technological changes in the industry. Stability in 1996The Canadian coal industry enjoyed another strong year in 1996 continuing a trend established over the last four years. The strength of the industry is based on a stable domestic industry and a relatively healthy inter- national market. The figures bear out these statements. In 1996 total production reached 75 million tonnes and consumption was 52 million tonnes. The major markets for coal in Canada are electricity generating stations (Alberta, Saskatchewan, Manitoba, Ontario, New Brunswick, Nova Scotia) and the steel industry in southern Ontario. Approximately 11 million tonnes of coal were imported and exports reached a new record of 34.5 million tonnes, mainly from western Canada. Canadian Coal FlowsCanada represents a unique case in the coal world because we both import and export coal (Fig. 1). The reason for this apparent dichotomy is Canada’s geography. Eastern Canadian coal markets are located closer to the eastern United States coal fields and are basically served by them. This is true for both thermal and metallurgical coal. Major imported coal users are the steel industry, electricity generators and other industry including the cement industry in southern Ontario, Quebec, New Brunswick, with a little coal imported into Manitoba. Only about 2.2 million tonnes of western Canadian coal move into the east, including both lignite and bituminous coal."

Jan 1, 1997

By W. Banda

Paper written on project work carried out in partial fulfilment of Phd. (Process Engineering) degree* The recovery of cobalt and copper from waste slag was studied in a plasma DC-arc furnace in reducing conditions. Three fluxes, CaO,CaF2, and TiO2, were investigated for their influence on selective recovery of cobalt into an iron-rich alloy. A further investigation on the influence of furnace power on the reduction of slag to recover cobalt to the alloy showed that a change in power setting had an unexpected effect on the recovery of metals to the alloy, in that selectivity of base metal recovery over iron recovery decreased at an increased power level. Keywords: DC-furnace, reduction, nonferrous, slags

Jan 1, 2004

By J. N. Van der Merwe

"Platinum is a highly valuable resource, its safe and economic extraction is paramount. The success of platinum mining by the bord and pillar method depends heavily on a comprehensive and dependable pillar design method. Pillars need to be large enough to safely support the load and small enough to avoid loss of resources. A critical evaluation of current pillar design systems used in narrow-reef platinum mining was undertaken using practical experience from a large feasibility-stage platinum exploration project, supplemented by observations from several platinum mines in Zimbabwe. An extensive literature survey was undertaken in order to determine the current status of design systems. Through this approach, the shortcomings of current pillar design systems are highlighted. Areas are proposed for further research to obtain a better understanding on how additional factors influence pillar system stability. The exploration work highlighted how rock mass classification methods can be utilized in determining the overall strength of pillars. Current pillar design systems for narrow-reef platinum mining consider width-to-heightratio (usually with different exponents for width and height) and the strength of the pillar material. However, there are many more important factors that are not considered and which have a bearing on pillar system stability. An in-depth study of these parameters with a view to establish effective narrow- reef platinum mining pillar design systems needs to be undertaken. IntroductionPillars have been used as a means of support since the early days of mining. Pillarsupported mining methods such as bord and pillar require a reliable design system for them to be successful. This paper presents an evaluation of the current hard-rock mining pillar design systems as applied to a practical large-scale narrow-reef platinum mining feasibility study. It is vital to have a dependable pillar design system for economic and sustainable mining. Using an extensive database collected from the project, the pillar strength formulae were tested and several discrepancies noted. This necessitates the establishment of more reliable pillar design systems. In narrow-reef platinum mining, large compressive stresses accompanied by geological and geotechnical factors contribute to pillar instability. A well-formulated pillar design system is required that accounts for such factors so as to minimize pillar failures."

Jan 1, 2017

By K. V. Konigsmann

"Mattagami Lake Mines Ltd operate a zinc-copper mine with an annual output of about 200,000 tons of zinc and 30,000 tons of copper concentrates. Zinc concentrates arc shipped to a company owned smelter in Valleyfield (a distance of 690 miles), for Export to Quebec City and also to Josephtown, Pennsylvania (1,060 miles, Figure 1.)The protection of concentrates in open gondola rail shipments has been a matter of concern since operations commenced. Considerable financial losses did occur at times because of wind erosion. Operating difficulties were also encountered by customers because of excessive moisture accummulation in the concentrates. Test shipments made in 1969 established the magnitude of losses in open cars. The results and subsequent investigations at our mines and elsewhere confirmed that load protection is an economic necessity.Many types of covers were experimented with, more or less successfully. In 1972 we agreed on a joint program with Dupont of Canada Limited. A new type of cover was developed by early 1973. It has been in use since, undergoing several improvements as experience accumulates."

Jan 1, 1975