Search Documents

By William W. Adams

Accidents to men employed in the quarrying and related industries of the United States were more numerous, absolutely and relatively, in 1937 than in 1936. Fortunately, the entire increase was in the category of nonfatal injuries, as accidents causing death declined in number and in proportion to the number of man-hours worked. Employment increased. More men were employed, more man-days and man-hours were worked, and the average employee had more hours of work than in 1936. Reports covering all commercial operations showed that 84,094 men were employed an increase of 5.1 percent over 1936. The number of man-hours of work performed by the industry was, 158 millions, an increase of 7.6 percent. Seventy-seven men were killed by accidents, a, reduction of 14 from the year before, and 6,348 men were injured and disabled for more than the remainder of the day on which the accident occurred, 11 percent more than in 1936. The fatality rate of 0.49 per million man-hours of exposure in 1937 compared favorably with the rate of 0.62 for the previous year, whereas the non-fatal-injury rate of 40.10 was 3.2 percent higher than the rate of 38.87 for 1936.

Jan 1, 1940

By E. C. Payne

"IntroductionTHE SMALLER industrial and commercial steam generating plants in the United States are suffering from an ‘engineering deficiency' which, if allowed to continue, will probably result in the extinction of the species• that now burn •approximately 75 million tons of coal. We will classify as 'small' those plants which should require not more than one operating man per shift, including those in which as little .as thirty minutes per day should be adequate for .all service attention. These are the small steam plants that need the most, and get the least, expert attention for fuel :planning, equipment selection, design layout, .and proper operating technique. Dissatisfaction with bituminous coal is usually caused by one or more preventable weaknesses such as excessive or burdensome labour •for firing, .coal or ash handling and manual operation, smoke and fly ash emission above nuisance levels:, high maintenance and premium coal application for acceptable operation, and .finally, overall steam costs which are not .competitive. These 'deficiencies', so .common in the small coal-fired steam plants, can be readily eliminated by competent engineering and modern equipment with automatic controls."

Jan 1, 1953

By J. B. Stott

The performance of an adiabatic calorimeter for measuring heats of oxidation of coal is assessed and suggestions made for its improvement and calibration. The use of magnetic analysers for measuring small oxygen deficiencies in air is described and three different methods of measuring the output for such a meter are characterised. The occurrence of spontaneous heating in an 800 tonne heap of Wyoming coal is briefly described. The major part of the report deals with the oxidation of Pittsburgh seam and Wyoming subbituminous coal and describes an experiment in which 1 tonne of Wyoming coal is stored in a 5 metre long insulated container whilst air was passed through. Temperature rises, rates of oxygen absorption and gas compositions of the air stream were measured. The report relates the results of these-experiments to a theory of spontaneous heating developed by Stott and Quan which stresses the importance of the moisture content of the coal and the relationship between the heat necessary to evaporate this water to the heat available from coal oxidation. The work was carried out over a five month period and the emphasis is on demonstrating the effects of moisture transfer and confirming the theory of Stott and Quan.

Jan 1, 1980

By Randolph R. Dreher, Michael L. Schreder

"In recent years, FFE Minerals has designed, installed and commissioned several large grinding mill circuits. This paper discusses the issues related to the erection and commissioning of large grinding mill circuits. The three circuits discussed are Collahuasi in Chile, Minera Los Pelambres in Chile, and Century Zinc in Australia. These circuits include large SAG and ball mills with both gear and gearless drive arrangements, as well as, both trunnion and shell supported mills. Aspects of these features are discussed with respect to their impact on installation and commissioning. While the normal challenges of mill erection and start-up were experienced, there were also a few unexpected challenges encountered partly due to the large scale of the equipment. An overview of the equipment and design ratings of these circuits is also provided.COLLAHUASIOverviewThe Collahuasi mills were started-up in November of 1998. The site is located in the Andes Mountains at an elevation of 4300 meters. The grinding circuit includes two lines featuring one SAG mill and one ball mill for each line. The circuit features a recycle conveyor around the SAG mills with provision for adding a pebble crusher in the future. The design tonnage of the grinding plant is 60,000 MTPD with an ore BWI of 10.5 kWh/MT.The SAG mills are 32’ x 15’ (1 3’ EGL) with 10,800 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The mills are driven by low speed synchronous motors with CCV variable speed drives. The SAG mills are trunnion supported and use hydrostatic lubrication. Feed to the SAG mills is via a rock-box type feed chute on a cart. The mills discharge on to trommel screens with a bucket wheel to remove the oversize.The ball mills are 22’ x 36.5’ (36’ EGL) with 12,500 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The fixed speed mills are driven by low speed synchronous motors with GE Quadramatic load sharing drives. The ball mills are shell-supported and feature multi-pad bearings with hydrodynamic lubrication. The mills are fed via a rubber lined sump box with feed spout on a cart. The ball mills also discharge on to trommel screens. Twenty-six inch (26”) diameter hydrocyclones are in closed circuit with the ball mills."

Jan 1, 2001

By A. H. Beebe

This paper describing the operations of the Cresson mine of the Cresson Consolidated Gold Mining & Milling Co. at Cripple Creek, Colorado, is one of a series of papers on mining methods and costs being prepared by the United States Bureau of Mines. The Cresson has recently been the most, important mine in the Cripple Creed district. During 1932 and 1933 an average of 230 tons of new ore (excluding dump material) that averaged about $10 in gold was shipped daily; 150 to 175 men were employed. Stoping was by the shrinkage method exclusively. The ore was screened washed, and hand-sorted at the surface and shipped to the Golden Cycle mill at Colorado Springs for treatment. A considerable proportion of the production was made by lessees working under the so-called "split-check" system. The authors are indebted to the management of the Cresson Consolidated Gold Mining & Milling Co. for permission to publish this paper.

Jan 1, 1934

By Matthew E. Fowler

The Central Subway will extend the recently completed 8.2-km long Third Street Light Rail line another 2.7 km north through the Union Square shopping district to Chinatown with a concourse-to-concourse connection to the Powell Street BART Station. One mined and two cut-and-cover subway stations are planned. Particular challenges include: tunneling under existing tunnels; variable ground conditions ranging from saturated alluvium to fractured bedrock; a congested urban setting and large-span caverns. This paper gives an overview of the project as it stands midway through the preliminary engineering stage along with a discussion of the rationale and design approaches that are being used to address the construction challenges of restoring light rail service in the most densely developed areas of San Francisco.

Jan 1, 2008

By Cam Thomas, Steve Bernard

Various types of blasting instrumentation can be used in the field to analyze conditions before, during and after a blast, and to indicate what changes need to be made. When different types of measurements are combined together, the blaster can end up with useful data that can pinpoint the source or sources of problems and what changes have to be made. This paper outlines two case examples where blasting instrumentation was used to overcome problems in separate quarry operations. Extensive measurements with different systems led to significantly improved blasting results.

Jan 1, 2012

By James V. Luxner

The airflow and methane distribution patterns developed in an equipment-free entry 6.5 feet high and 12 feet wide, ventilated by line brattice operated blowing to or exhausting from the face, were determined by the Bureau of Mines for varying conditions. Results of these studies show that blowing line brattice systems of face ventilation are more effective than comparable exhaust systems. The face ventilating efficiency of any line brattice system is dependent upon the method of ventilation, the face distance, the tight rib distance, the volume of air delivered to the end of the line brattice, and the volume of methane released at the face. Experimental results indicate that maximum face ventilation efficiency is achieved when the inby terminus of the line brattice is installed 5 feet from the face and at a distance less than one-third the entry width from the nearest rib. Analyses of data are based upon the ability of a face ventilation system to dilute methane in the immediate face area.

Jan 1, 1969

By Fred D. DeVaney, C. W. Ambler

"Copper sulphate is a common flotation reagent for blende ores. Metallic iron also is present in the mill circuit, and a reaction between the iron and the salt would be in accord with well-known chemistry. The abundance of metallic iron in a flotation feed may be noted by even perfunctory examination. First of all the mine contributes metallic iron, then the coarse-crushing machines add their share, and finally the fine-grinding medium its portion. If the grinding is with cast-iron balls the amount of metallics is greater than when steel is used. Thus it is that much more metallic iron is present than would be indicated by noting the ball consumption. An estimate that the total amount of metallics is twice that supplied by the balls and liners might not be far amiss.That copper sulphate plates out on iron in an acid solution is well known, but since flotation is practiced commonly in solutions where acid has not been added this reaction has not been given sufficient thought.This problem has been the basis of a study undertaken jointly by the Mississippi Valley Station of the United States Bureau of Mines and the Missouri School of Mines and Metallurgy, at Rolla, Missouri. Its importance may be understood better when the tonnage of zinc ores now being treated by flotation in this country is considered. According to Gaudin4 5,536,244 tons of zinc or were treated by flotation during 1927. In these operations copper sulphate was employed as an activating agent; the amount per ton averaged 0.81 pound for straight sulphide zinc ores and 1.16 pounds for complex ores. Since such large quantities of zinc ore are treated by flotation and since metallic iron is always present, the importance of studying their reactions on each other and the effect of their reaction"

Dec 1, 1929

By M Boon, M Franklin

This paper outlines the journey of cultural maturation and management system development at the Mt Rawdon (MRO) gold mine from its acquisition by Evolution Mining Limited (Evolution) in late 2011 to 2016.Evolution embarked upon a series of projects that aimed to improve the operational consistency and implementation of change on-site, while leveraging off the existing strengths of the operation. This document describes the gaps that were identified, the processes used to close them, and the resulting cultural change and production outcomes, with a specific focus on how to optimise the culture at any mining operation.MRO had a history of four owners in less than three years when it became a key asset of Evolution. The site leadership team (SLT) decided to influence the culture at MRO by reviewing and upgrading the existing management processes.The first priority was to improve transparency and collaboration at the SLT level, followed by improving competency in project management. The next phase was to strengthen the internal communication using a deliberately designed network of meetings, communication screens and other initiatives. Once there was some traction, the focus moved toward increasing production volume and decreasing cost per unit by improving short-term planning and execution capability. Together with other initiatives, this resulted in improved collaboration between all functions, which in turn netted over 37 per cent mining production uplift.Following solid success, a process of prioritisation and alignment management was implemented. This supported the ‘Mine to Mill one operation’ ideal and allowed the SLT to decide month-by-month what actions were to be prioritised. These priorities incorporated production realities and longer term imperatives of the balanced business plan.Much of this work was completed during a period of declining gold prices and a relentlessly strong Australian dollar, making it difficult to justify spending money on improvement projects. This work proved critical for the operation’s long-term survival.CITATION:Boon, M and Franklin, M, 2016. Improving consistency of delivery at Mt Rawdon Operation, in Proceedings International Mine Management Conference, pp 305-320 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By Joseph M. Singer

This research project had two main objectives: (1) To identify the smoke limits of gaseous fuel-air mixtures and (2) to obtain and evaluate basic chemical information on the formation of smoke in very rich flames near the smoke limit. Such information would do much to establish the circumstances for car-bon deposition in gas appliances and in other types of combustors. Based on tests with ethylene and propane, these studies showed the following: 1. Smoke limits are related to the yellow-tip limits of the fuel. Previous research established sufficient data to permit prediction of yellow-tip limits on gas burners using a wide variety of fuels. The present study of smoke limits deals only with ethylene-air flames, but the concept that was developed is probably applicable to other fuels.

Jan 1, 1962

By C. F. Vos

Small replacements of C12-trithiocarbonate (C12-TTC) for dithiocarbonate (DTC)/dithiophosphate (DTP) in a reagent suite for the flotation of platinum group metals (PGM) have significantly improved the rejection of gangue. Coupled to this is an improvement in kinetics, grade and recovery of PGMs. In a pilot-plant trial, after a 5 mole per cent replacement of the current DTC/DTP collector combination by C12-TTC, large opaque bubbles were replaced by small clear ones. In addition, a similar flotation response was realized with one-third of the current depressant dosage. During a preliminary plant trial on underground UG2 ore, the initial rougher concentrates were characterized by higher PGM concentrate grades and this was in part due to improved chromiter ejection. The concentrate produced from the TTC trial also exhibited a much finer particle size distribution. The overall circuit performance, which included secondary regrind and flotation, showed an increase in concentrate grade of approximately 44% while the tailings grade remained unchanged

Jan 1, 2007

By L. R. Stark

Two wetland simulation experiments were carried out in order to determine the effects on manganese retention of several wetland design parameters, including flow rate, inlet pH, carbon supplementation, substrate type, and surface free water depth. The primary aim in each experiment was to determine if sustained manganese retention could be accomplished under the specific experimental treatments. If successful, these experiments could recommend design parameters for the construction of field wetland systems for manganese treatment. Crushed limestone clearly was superior to spent mushroom compost with respect to manganese retention. The presence of free surface water detracted from manganese treatment, while lower flow rates enhanced manganese treatment. Sustained manganese retention was achieved using crushed limestone as the substrate coupled with an absence of surface free water, under inlet water conditions of pH 7.0 and no appreciable iron. Sustained manganese retention was not achieved under reducing conditions using spent mushroom compost while varying flow rate, inlet pH, and carbon supplementation regimes. However, lowering the flow rate resulted in many significant beneficial effects on outlet water chemistry: lower outlet manganese concentrations (over the short term), higher outlet pH, lower outlet acidity, higher outlet alkalinity, higher outlet sulfide, lower outlet sulfate, and lower outlet redox potential. Supplementation of the wetlands with dairy whey resulted in lower outlet manganese concentrations (over the short term), marginally higher outlet sulfide levels, and acted to lower the redox potential under the high flow regime. Wetlands receiving a neutral pH had lower outlet acidity, higher outlet alkalinity, lower outlet sulfate, but equivalent outlet manganese concentrations than wetlands receiving an acidic pH. When manganese is the primary mine water contaminant and a passive water treatment system is to be used, it is recommended that crushed limestone with negligible surface water be used in place of composted materials. This recommendation assumes a source water with circumneutral pH and an absence of other metals.

Jan 1, 1993

By T. E. Wakefield

Over several decades in Southern Africa the advance rates when sinking vertical shafts have declined significantly. The upside has been a substantial improvement in shaft bottom conditions and a commensurately improved safety performance, with an increasing number of shafts being sunk without fatalities and disabling injuries. This paper briefly reviews historical sinking rates and matches changed sinking productivity to the introduction of new sinking methods that have been adopted to eliminate/mitigate safety risks. Meeting the challenge of returning to historical advance rates whilst progressing in the quest for zero harm by utilizing three dimensional animated computer modelling is described. Making use of commercial modelling software makes it easier to evaluate different methods, sequencing, in shaft barrel ergonomics, and stage and shaft bottom layouts before procuring project plant and equipment. Benefits accrue not only in better communicating methods and configurations for detailed planning and design, but also during crew training. The traditional engineering ?as-built? drawing practice has been extended to the concept of an ?as executed? sinking model which seeks to capture operational experience and learning for future best practice. The paper concludes with some of the organizational culture challenges being overcome as this non traditional approach to shaft sinking optimization is being introduced.

Jan 1, 2009

The epithermal Au-Ag deposits of the Hauraki Goldfield have formed in the convergent plate margin setting of the Coromandel Volcanic Zone (CVZ). The deposits form as siliceous lodes in the upper parts of geothermal systems associated with andesitic and rhyolitic volcanism. Two types of low sulphidation epithermal mineralisation are recognised in these volcanic terranes. Vein deposits within the rhyolitic terrane in the east and south of the CVZ (Whitianga Province) are typified by Chalcedonic Silica-Adularia-Illite type mineralisation. The veins are hosted by both rhyolite-dacite volcanic rocks and the underlying andesitic basement. The mineralisation formed by episodic violent decompressional boiling of deeply circulating meteoric water, with some magmatic fluid contribution; this boiling was associated with hydraulic fracturing and hydrothermal eruptions in geothermal systems where the piezometric surface of the deep geothermal reservoir lay near-surface. Such episodic boiling provides chalcedonic veining, banding and brecciation textures, adularia stability, bladed calcite, and extreme loss of H2S gas from the fluid to cause major gold deposition.   Crystalline Quartz-Illite-(Adularia-Kaolinite) type mineralisation is widespread in the andesitic terrane forming the northern and western portions of the CVZ (Kuaotunu Province). There is a spatial association with weak mineralisation of the high sulphidation (Vuggy Silica-Alunite-Kaolinite-Illite) epithermal type and porphyry eu-Au type. Crystalline Quartz mineralisation is probably formed by the mixing of shallow acidic groundwaters with the ascending deep geothermal fluid in geothermal systems beneath andesitic stratovolcanoes. The piezometric surface to the deep geothermal reservoir in these systems is likely to lie at considerable depth, with acidic gases rising from the geothermal reservoir condensing within the overlying vadose zone. The cooling effect, oxidation and pH decrease accompanying mixing apparently overcomes the dilution effect, and results in quartz deposition, illite (and locally kaolinite) alteration, and precipitation of gold. A high level of base-metal sulphide precipitation also enhances gold deposition. Violent boiling of the mixing fluids may occur at local structural dilation sites, producing high grade "bonanza" gold mineralisation.

Jan 1, 1991

By A. Sheikh, S. Hardcastle

"Various methods of leaching are being used by Denison Mines Ltd. Uranium Operations. This study was designed to investigate the flood leaching operation of two parallel inter-connected stopes contained by pressure bulkheads. The teaching muck piles, created from large scale uppers production blasts, are aerated by compressed air lines laid beneath the pile prior to blasting.A SFr, tracer gas, injection technique has been employed to determine the post-blast integrity of the single-ended air distribution system. SF6 was injected into the compressed air line feed to the stopes and collected at borehole exhausts from the stopes in grab-sampling bags. Analyses of the air samples were performed with a gas chromatograph.The system was designed to give a sufficiency of oxygen to sustain bacterial activities used to enhance the leaching recovery in the muck piles. The results obtained indicated that there is a minor anomaly in the distribution system that may not be critical to the operation. Compared to an idealized case, the over-all efficiency of aeration throughout the muck is estimated at over 85%."

Jan 1, 1988

By Louis D. Huntoon

CANADIAN gold production is forging ahead annually and the prospects are that it will continue to do so for many years. Table 1 shows recent annual increases. Production for 1933 will probably reach $70,000,000, and further increases are likely in 1934 and 1935. (Data for November and December, 1932, are estimated throughout this article.) The depression sent many prospectors to the woods so during the last two years many new gold areas have been discovered and are attracting real capital for exploration and development. Several mills came into production in 1932 and mills now under construction will start production in 1933. The offices of mining lawyers are busy. Capital for this new work is obtained from well financed mining companies, syndicates, and individuals who were fortunate enough to invest in the dividend-paying gold mines of the north country in the early days. Prospectors and capital are cooperating. An interest is always retained by the prospector or vender and usually a small amount of real money is given the prospector.

Jan 1, 1933

By John C. Machisak

INJURY experience and employment data at all metal mines in the United States and Alaska are presented in this Information Circular for the calendar year 1958. This publication covers the metal mining industries, and contains statistical data on injuries and employment pertinent to metal mines, ore-dressing plants, and primary nonferrous smelters, refineries, and reduction plants. These operations report injury and employment information annually to the Bureau of Mines on a voluntary basis. The Bureau is authorized to make requests for such data, and the information submitted contributes immeasurably to the promotion of safety in the metal mining industry. Every effort has been made to make the annual canvass as complete as possible. This publication contains, along with production and development workers, the office employees at the mine location. The metal mines identified in this publication are classified according to the mineral ores mined; that is, copper, iron, lead-zinc, gold-silver lode, gold placer, and miscellaneous metals.

Jan 1, 1962

By Darío Innamorati, Jorge Oliva

Cerro Vanguardia is a known gold and silver deposit located in the province of Santa Cruz, Argentina. The mine has been in operation since 1998 and is thought to be one of the most important mines in Patagonia. More than 102 epithermal quartz veins have been identified in the area, with variable lengths, thicknesses, orientations and dips that constitute what is possibly one of the most extensive outcropping vein systems on earth. Veins are vertical and have variable depth. For this reason, the deposit is currently mined with a variety of extraction methods. This operation is made up of more than 60 open pits and 20 underground access ramps to exploit the deepest high grade narrow veins. This study is focused on the combination of underground exploitation with open pit blasting. That is, those production stopes in the upper levels of underground mines and their interaction with the damage levels in the final slope of open pit mines, as well as in the study of the impact of the generation of vibrations from the blasting of open pit mines and their influence on underground mines. Considering the current stage of the mine, after 20 years of operation, Cerro Vanguardia faces the need to mine deeper deposits in the face of increasing costs and declining grades. For this reason, it is essential to study the interaction of these exploitations. From a personnel safety point of view, this interaction must be well coordinated so as not to affect people and equipment. Likewise, the generation of vibrations due to blasting must be studied, which would produce new cracks, potentially generating overbreak and dilution. The main objective of this study is to determine the possible causes and influences of the blasting interaction in open pit and underground mines, seeking an optimization of the blasting process and a safety standard for personnel and equipment. To achieve these goals, this study includes a vibration monitoring plan to analyze the charge performance and determine rock constants. With the use of specialized software, damage modelling and simulations are used to determine values of damage in order to reduce overbreak. In addition, this plan contemplates the estimation of flyrock in blasting where underground work is connected to the surface, determining safety distances when carrying out a blast.

Jan 21, 2025

By W. A. Burns

Vertical flow is an important mechanism in many petroleum reservoirs. Yet no adequate method has heretofore been proposed for determining the in-situ vertical permeability in a reasonable length of time. Core measurements of vertical permeability do not necessarily represent effective in-situ values. Cores may be representative of only localized pockets of high or low permeability, and total reliance on cores might cause one to overlook the presence of vertical fractures altogether. Conventional single-well tests, interference tests, and pulse tests commonly are used to determine horizontal transmissibility, khh/u, but generally are not designed to measure vertical trans-missibility or other groups containing vertical permeability, ku. A new well test described here provides a measure of in-situ vertical permeability as well as the previously measurable horizontal permeability. This "vertical test" determines the vertical diffusivity, kv/gcu, and horizontal transmissibility, khd1/u (where dl is the length of injection or production perforations). The test is basically a short-term interference or pulse test normally lasting less than a day. Conventional down-hole equipment is used between two isolated sets of perforations in the same well, as shown in Fig. 1. A "layer-cake" description of a reservoir can be obtained by running two or more vertical tests in the same well, each over different vertical intervals. Each test can be analyzed for the effective vertical and horizontal properties of the interval tested. In addition, a vertical well test can determine the effective- ness of a shale barrier or tight zone by testing across it. Field use to date of vertical testing has confirmed its utility in reservoir description. Mathematical Basis Interpretation of vertical tests for ku and kh is based on comparison of measured pressure response with computer-generated response. Pressure behavior during a vertical test in a homogeneous, anisotropic, infinite-acting reservoir (infinite in radial extent and bounded in both directions vertically) is given by the diffusion equation for slightly compressible fluids with negligible gravity effects.l A schematic diagram of the problem is presented in Fig. 2, and an analytic solution, based on the image

Jan 1, 1970