Search Documents

Anglo American Metallurgical Coal (AAMC) manages five open cut coal mines in Queensland and New South Wales, producing approximately 30 million tonnes per annum. The size and complexity of these mines require efforts by a large and diverse number of personnel to minimise adverse geotechnical events from occurring. To achieve this, the AAMC coal mines in Australia are developing a concept of managing the geotechnical risks associated with open cut coal mines. The overall system utilises a combination of internal training, a management system (operational management systems) and standards, numerical modelling, monitoring, inspections and audits. The development of the standards as well as training and mentoring of exploration personnel, geotechnical engineers, engineering geologists and mining engineers with an interest in the geotechnical aspects of mining, training of the production workforce, mentoring and training of the technical staff create the basis for achieving a pro-active rather than a reactive system. Audits are used to assure that personnel are maintaining the standards and to facilitate cross-mine leanings so that best practices are developed across all sites.

Nov 25, 2010

By George A. Costello

A theoretical analysis is presented for the static and dynamic response of wire rope in deep-shaft mining operations. Expressions for the stresses in the individual wires of complex wire ropes are derived, and specific results for simple strands, 7x7 ropes, 6x 19 Seale ropes both with and without internal-wire-rope cores, and 6x25 filler-wire ropes both with and without internal-wire-rope cores, are presented for the case of ropes subjected to a combination of axial loading and bending over a sheave. Consideration is also given to the dynamic overloading associated with certain mining operations, such as dumping ore into a suspended skip and accelerating a fully loaded skip upward. Experiments to determine the axial stiffness of wire rope are described. Factors affecting the service life of wire rope, such as residual stresses, contact stresses, and fatigue behavior, are discussed. Specific research areas in need of further investigation are identified.

Jan 1, 1983

The Federal Coal Mine Health and Safety Act of 1969 requires that each operator of a coal mine shall take accurate samples of the amount of respirable dust in the mine atmosphere to which each miner is exposed, a measure designed to prevent the development of coal workers' pneumoconiosis. This textbook manual is used in the training of personnel to operate respirable dust sampling devices and to conduct sampling programs. It contains the portions of the act applicable to respirable dust standards, the procedures to be followed to insure compliance with Federal regulations, and descriptions of sampling devices.

Jan 1, 1971

By Russell J. Foster

Many important materials are derived entirely or partially as byproducts of primary copper, lead, and zinc production. This U.S. Bureau of Mines report examines the collective role of byproducts with regard to the economics of domestic mineral production, and their individual significance in terms of dollar value, end uses, and strategic considerations. The study also analyzes circumstances that have affected the competitiveness and structure of the U.S. copper, lead, and zinc industries, and factors that impact byproduct availability. These factors include production capacity at smelters and refineries, process technology, changing sources and composition of ores, regulations, foreign ownership, and byproduct demand and price. Policy considerations regarding stockpiling, regulations, and research are assessed.

Jan 1, 1991

The pyrite-sphalerite-galena and barite orebodies at the Rosebery mine are concordant with the shale host rock and have been deformed into one system of folds with an associated axial plane cleavage. The folds are tight and overturned with east-dipping axial planes. Folds in the sulphide ore are commonly disharmonic, particularly between adjacent bands of different composition.Concentric style folds occur in the competent bands, e.g. pyrite-rich bands. Similar style folds are predominant in the less competent sphalerite-galena-rich bands and also in the shale of the host rock. The trends and plunges of the fold hinge-lines are variable but axial planes are of reasonably constant orientation throughout the mine area. The folds in the orebodies are of limited axial extent, approximating to conical folds, and are arranged in en echelon patterns. The fold system was possibly formed in one period of folding by heterogeneous strain that may have been caused by the presence of a mass of tectonically mobile sulphide ore. Lineations parallel to the ore/host rock contacts appear to reflect movement between the ore and the host rock during folding.

Jan 1, 1972

By James Westfield

Bureau of Mines activities for safety and health in the mineral industries were reorganized during the fiscal year to provide direct supervision by the Assistant Director -Health and Safety. On December 19, 1954, the field offices conducting these activities were designated as district health and safety offices reporting to the Assistant Director. The functions of determining the causes of accidents and injuries in the mineral industries and recommending measures to eliminate them were continued, with satisfactory results in improved safety records. The inspection of coal mines and enforcement of the Federal Coal Mine Safety Act of 1952 were conducted as directed by the Congress, and safety conditions in the mines were notably improved. One coal-mine explosion classed as a major disaster occurred during the year. The causes of that explosion and means for preventing a recurrence were still under investigation because of the extreme difficulty in recovering several portions of the mine. Basic research on the nature of certain hazards and ways of eliminating them is continued. Training of individual workmen and supervisors in this knowledge is a major part of the work.

Jan 1, 1956

By Mathew Janes

"Sheet piles remain an economic solution to many shoring problems. However, installation of sheet piling suffers high noise and vibration with conventional impact or vibratory methods or low production and high expense with push techniques. Many projects simply will not allow sheet piling due to vibration concerns.Installing sheet piles with a tunable, high frequency Resonant vibrator provides high production with imperceptible ground vibrations. Recent projects in Canada have proven the technique on production projects where vibration sensitive structures are present immediately adjacent to the sheet piling. A project in Whitehorse, Yukon required a Waterloo style impervious sheet pile barrier be driven immediately adjacent to a sensitive, large diameter sewer line. The 1800 m2 Waterloo barrier was driven to prevent hydrocarbon leachate from entering the Yukon River. Proposed driving of the sheet raised concerned as the sewer serviced downtown Whitehorse. Monitoring of the sewer during Resonant driving proved the ground vibrations to be imperceptible. Use of the Resonant Driver prevented all concern over ground borne vibration of the sewer and allowed the contractor to progress at conventional, high production while maintaining low cost to the owner.Subsequent projects continue to prove that Resonant driving of sheet piles achieves high production while eliminating ground vibration.IntroductionA complex environmental clean-up problem required a unique solution. A historic oil and fuel transfer station in Whitehorse, Yukon is located on the Yukon River. The facility has been in use since the Second World War and witnessed much careless activity. The sand and gravel site provided ease of transmission of hydrocarbon leachates directly into the Yukon River. Continued use of the site required a barrier wall be constructed to prevent hydrocarbon from leaching into the Yukon River. A short construction season and restrictive fisheries window made for a compressed schedule. Along the shoreline of the property and within the required clean up zone a large diameter sanitary sewer collector line was present that serviced the majority of downtown Whitehorse. The design called for a barrier wall to be constructed along the waterfront adjacent to the sewer with cofferdams constructed out into the Yukon River to recover contaminated riverbed soils. The coarse sands and gravels meant high hydraulic conductivity into any kind of excavation, including slurried or drilled shafts that may have been used to construct a low vibration shoring system. Conventional hammer or vibrator technology would result in high ground vibrations that risked damaging the sewer. The Resonant Driver method was selected for its ability to drive sheet piles with high production and zero ground borne vibrations."

Jan 1, 2014

By S. P. Singh

The purpose of the cut is to provide a free face to which the remainder of a development or breasting round can break. The results of field testing in drifts and at a quarry face were used as a basis for a description of the rock breakage and flushing mechanism in the cut. It was concluded that the important features of a cut design are proper hole spacing, sufficient relief volume, drilling accuracy and relief holes slightly longer than the planned length of the round. The void space provided by the relief holes should be about 15% of the cut volume, with more required in weak, highly fissured rocks. The importance of drilling accuracy increases with round length, an error being magnified by the small blasthole spacing. The first hole pulls only about 20% of the round length, 4-6 holes having to be fired before the cut is pulled close to its design depth. The first four blastholes should be fired with a minimum inter-hole delay of 100 ms to provide progressive relief of burden and avoid the superimposition of ground vibrations. The earliest-firing charge should be closest to the relief area and act laterally, while the first of the vertically-fired charges to be detonated should be the uppermost. Problems during cut-pulling include sympathetic detonation, dynamic pressure desensitisation, charge disruption and freezing of the cut

Dec 1, 1995

By Ross W. Smith

In recent years there has been a considerable amount of research work done relative to the effect of pretreatment and aging in water on the surface properties of both simple metal oxides and more complex oxides such as the silicate minerals 1-6. Of particular interest is the work of Somasundaran6 who states that after preparing minerals by size reduction and washing with dilute acids "... it is essential to treat it (the mineral) with water in order to remove any effects of leaching itself." Somasundaran also states, "... it is advisable to use a solution close to the point of zero charge for conditioning purposes." Parksl notes that, "Dehydration, dehydroxylation, and increased crystallinity can be expected to decrease the PZC. The presence of anionic impurities or of pH-independent potential determining ions will decrease the PZC. Cationic species will increase the PZC." Healy and Jellett4 believe that in the Zn0-water system "the surface charge of Zn0 in water and each pH is determined by the concentration and adsorption of each hydrolyzed (charged and uncharged) Zn(II) species." Finally, according to Parks 2, "The PZC of an unaltered com¬plex oxide in a system devoid of specific electrolytes is approximately the average of the PZC's of its component oxides... Equilibration with water results in loss of mono and divalent cations by exchange with H+, thus a loss of influence on the PZC by those cations, i.e., a shift in the PZC with time in the direction of that remaining oxide. The present paper investigates the change of point of zero charge (PZC) of a number of simple oxides and several complex oxides as a function of aging time in water. In some cases acid pretreatment of minerals was performed. However, in most cases the minerals were not acid pretreated. In several systems pH change as a function of aging time in water was monitored.

Jan 1, 1972

By Kengo Usui

The energy consumption of Iron-making, especially Blast Furnace (BF), is very large. In order to maximize the utilization of limited resource, it is essential to reduce energy consumption and recovering waste energy in BF. This paper introduces energy saving equipment based on NSENGI’s over 80 BF construction experiences since 1963. The first is the technology for the Top Charging System for low fuel-rate operation. One of the important factors to achieve such operation, the burden should be charged uniformly. Since 1974, NSENGI have developed and delivered over 80 Top Charging equipments for such purpose and nowadays, developed new type Top Charging equipment with improvement of charging precision. The second is the technology for Solely BFG Operation in Hot Stove, which means no use of other fuel gas such as LDG, COG. It is realized by high combustibility of NSENGI’s Top-Combustion Hot Stove with Metallic Burners, and large amount of heat recovery of Waste gas Heat Recovery system with heat medium. The third is the technology for effective energy recovery in TRT. With NSENGI’s latest Gas Cleaning System “Multi-Vessel Electrostatic Precipitator" (MVEP), TRT will be able to generate higher electrical energy by approx. 30% than that of wet-type. In comparison with dry bag-type, MVEP allows temperature fluctuation which lead to generate higher electrical energy by approx. 10% NSENGI therefore, will be able to accept and meet your request widely.

Aug 1, 2018

By V. Bondarenko

The forecasting of floating earth inrush into the working is to a great extent connected with the investigation of the rock mass stressed-deformed state around the working. The aim of such investigations is to estimate the carrier ability of the protective layer (which is stabilized by the physico-chemical mode of fixing) and to determine it's thickness, which is to be sufficient to present the floating earth inrush into the working. We consider the protective layer to have exhausted it's carrier ability if the rocks of this layer reached the overlimit phase of deformation and it's greater part (section), which adjoins the working. is destroyed up to the limit of the remaining strength. So, the aim of investigations is to determine the size of the rocks inelastic deformation zone in the roof of the working. It is necessary to take into account the presence of water saturated seam in the roof and the overlimit characteristics of the rocks, their ability to lower the carrier capacity up to the level of the remaining strength.

Jan 1, 1996

By H. -J. Langhoff

"The paper describes not a result, but a starting point to implement sustainable development to a region characterized by a typical down river landscape, agriculture, and extractive industry. The NaturFreizeitNiederrhein GmbH (NFN) is a private company with associates from administrative bodies, the local mining companies and multiple representatives of environmental protection groups (local and national), tourism organizations, cultural societies and also aquatic sport and fishing clubs. Center of the concept is the "NFN Lake District." The development concept aims to provide the agricultural industry with alternative means of income, while protecting wildlife and the ecological balance as well as preserving the social und cultural system and enhance the safety against flooding from the river Rhine. The mining industry contributes their coordination of obligation concerning reclamation and recultivation of the already existing individual projects. While designing the landscape components and establishing the infrastructure for the different tasks, the production of gravel and sand is yield as a by product. The result is a long term perspective for region and industry."

Jan 1, 2005

By J. R. Stone, G. D. Storm

Design features and operating methods of ASARCO's new unit for the continuous melting and casting of tough pitch copper at Perth Amboy are described. Preliminary studies made for determinitzg economic feasibility and design details are also presented. Cathodes are preheated with oil and melted in an electric furnace at 40-ton per hr rate, from whence the molten copper is fed simultaneously to the wire bar casting wheel and the continuous casting of cakes and billets. In the early 1950's the copper refining furnaces at ASARCO's Perth Amboy plant reached a point where major expenditures would have to be made for replacement of the furnaces and the auxiliary equipment. The problem was whether to continue with the standard reverberatory furnaces or to consider continuous melting in electric furnaces. Reverberatory furnaces have been used for years in the copper industry and for some 50 years at the Perth Amboy plant. Reverberatory melting practice, however, imposes certain restrictions. First, labor costs are high, usually requiring three shifts per day. Secondly, they operate on a batch basis, the conventional operation being a 24-hr cycle including

Jan 1, 1961

By Ralph B. S

Bacterial leaching of low grade quartz felspar porphyry copper ore was studied in large-scale laboratory percolation leaching columns.Limitations in the release of soluble copper showed up before fifty per cent recovery, due to occluding precipitates of iron oxides and hydroxides. Precipitates were removed by increasing the acidity of irrigation feed four-fold with respect to sulphuric acid. However, irrigation at low pH (pH 1.5) inhibited copper leaching. Resumption of bacterial leaching at pH2 was achieved by introducing a period of non-irrigation. The results suggest a 'direct' attack by bacteria on the chalcopyrite substrate rather than an 'indirect' ferric-leach mechanism.

Jan 1, 1981

By D James

Fletcher Challenge Limited through its subsidiary Grampian Mining Co Limited has carried out an ore evaluation of one of New Zealand's largest known deposits of ilmenite located at Barrytown on the West Coast of the South Island, New Zealand. The ilmenite is located in a beach sand environment which has previously been mined for gold. Two analytical techniques were developed to quantify the resource. Considerable difficulty was experienced in this phase of the evaluation due to the presence of major inclusions within the ilmenite grains. Wet and dry concentration circuits, utilising spiral, wet magnet, high tension and plate electrostatic separators have been designed to produce ilmenite from the ore. Studies to utilise the titanium content of the Barrytown ilmenite have been made. Recent work has been directed towards a titanium dioxide pigment process.

Jan 1, 1986

By M. Pillay

INTRODUCTION Heat stress continues to be a safety concern in underground mining. This is due to a number of reasons including increasing depths of mining, increased levels of heat generated from machines, ventilation systems being constrained from providing suitable levels of airflow and others. In order to assess if a thermal environment is safe for miners under normal or modified work arrangements, or to specify stop work conditions a heat stress index is used to guide decisions. Historically, a number of heat stress indices have been developed and applied in underground mines. These can be classed under three broad headings; single measurement, empirically based and rational indices. Do any of these indices perform better than the others? Which one allows simple determinations and decisions to be made in the mine? This paper aims to provide answers to these questions by comparing and contrasting three indices; effective temperature (ET), simple air cooling power (ACP) and Thermal work limit (TWL) for a range of typical mining wet and dry bulb combinations? The paper concludes with the identification of areas for future research. BACKGROUND Heat stress causes discomfort, increases physiological strain, decreases productivity and performance, and contributes to increased incidents [1]. Effective management and control of heat stress is particularly important in mining where hot working conditions are very common [2]. Heat stress index is a common indicator that is used by mine safety advisors and managers to guide decisions about safe work practices in mining under normal or modified conditions. According to Howes and Nixon [3] A safe heat stress control strategy for an underground mine has three elements: • Application of an environmental measure which reflects physiological strain with sufficient accuracy for the range of conditions encountered underground. • Acceptance of a functional relationship between the environmental measure and human performance which is used to optimise the environmental conditions achievable with either ventilation or ventilation and refrigeration. • A management control strategy based on the environmental measure which is designed to ensure that work in environments where excessive physiological strain may occur is prevented and corrective action is initiated. The link between these elements is an environmental measure that reflects the physiological strain a worker is subjected to. Since the turn of the twentieth century various indices of thermal stress have been developed (McPherson [4], Howes and Nixon [3], Brake [5]). In selecting a suitable environmental measure or index one problem that must be addressed is the ease with which it can be physically obtained relative to it accurately reflecting the physiological strain. No index can be universally applied and there is no single correct measure or index. However if an index has provided adequate control in a particular circumstance, then it can be regarded as correct for that situation.

Jan 1, 2019

By T. Lindstad, S. Gaal, S. Hansen, S. Prytz

The SINTEF SiO-reactivity test, developed by Tuset and Raaness in the 1970?s, is a recognised method of characterising the ?reactivity? of carbonaceous reactants, used in the ferrosilicon and silicon metal industries. Recently, the test has been updated, which has resulted in the development of an extended and improved SINTEF SiO reactivity test. This has included updating the test reactor, control system, data-logging, handling and preparation of carbonaceous materials to be tested and measurement procedure. The scientific basis has been re-assessed, resulting in a new interpretation of the test results. The repeatability of the test has improved significantly, especially through system automation. In the ?old? test, the kinetics of the reaction: SiO(g) + 2C(s) = SiC(s) + CO(g) for a specific carbonaceous material was characterised solely by the ?R10? parameter, the volume of SiO(g) which passes un-reacted through the coke-bed as the concentration of CO in the outlet gas decreases from 18 to 10%. As both the kinetics and obtainable conversion of SiO to SiC for a reductant is of importance to the ferroalloy producer, the new SINTEF SiO reactivity test ranks carbon materials both according to degree of conversion and reaction rate. From research carried out on the test in the past couple of years at SINTEF and NTNU, it has also become clear that some of the reactions taking place in the test reactor are more complex than previously assumed. As an example, it was previously assumed that the condensation reaction of SiO gas in the condensation chamber of the test reactor can be described as: 2 SiO(g) = Si(l,s) + SiO2(s). However, it has been established that the side-reaction: CO(g) + 2Si(l) = SiC(s) + SiO(g) causes approximately 10% of the total volume of CO to react to SiC and SiO2 in the condensation chamber. This means that some back-reaction i.e., the reverse SiO-generator reaction 3SiO(g) + CO(g) = 2SiO2 + SiC also takes place in the condensation chamber. In the new SINTEF test, the %CO versus time curves are therefore corrected in order to describe the effect of the reaction between SiO(g) and C(s) studied i.e., SiO(g) + 2C(s) = SiC(s) + CO(g). A correction-formula for this purpose is presented.

Jan 1, 2007

By H. J. Ilgner

The paper reviews the results to date of an integrated research programme currently being conducted by CSIR Mining Technology, aimed at impacting significantly on concentrated mining with face advance rates of up to 20 times faster than presently achieved. Consideration is given to the interplay between innovative technologies for continuous non-explosive mining or rock comminution underground and lateral hydraulic transportation in cross cuts, haulages and eventually hydro hoisting. Novel technologies for underground comminution of reef and development waste and an innovative pumping system suitable for the hydraulic transportation of coarse comminuted rock are reviewed. Emphasis is placed on South African gold mine reef and waste samples comminuted by electric shock wave comminution technology. The innovative TORE® pump system appears to be well suited for the successful hydraulic transportation of rock, produced by electric shock wave comminution, at solids concentrations between 45 % and 67 % by mass.

Jan 1, 1997

By Rimas Pakalnis, Andrea M. Ouchi, Thomas M. Brady, Mary M. MacLaughlin, Cristian Caceres, Paul Hughes

A major focus of ground control research presently being conducted by the Geomechanics Group at the University of British Columbia, Canada, in conjunction with the National Institute for Occupational Safety and Health’s (NIOSH) Spokane Research Laboratory, is the development of design guidelines for underground mining within weak rock masses. The study expands upon the span design curve for man-entry operations and the stability graph for nonentry operations developed at UBC by extending the application to weak rock masses. The original database has been augmented by weak rock mass information from mines throughout the United States, Canada, Australia, Indonesia, and Europe. The common factor in all of these mines is the presence of a weak back and/or walls. This paper expands on the North American database and how the design curves have been employed at mining operations throughout the world. The definition of a weak rock mass for this study has been defined as having an RMR76 under 45% and/or a Q-value under 1.0.

Jan 5, 2007

By D. Peatfield

The design and operation of coal preparation plants are governed by the inherent quality of the raw coal to be processed, market specifications and the saleable tonnage requirements. Topography influences the layout of the plant but does not affect the process design. The coal market comprises many sectors, each having specific requirements with respect to both size and quality. In turn, these have led to different levels of preparation and the development of specific types of coal preparation plant design. Developments in processing techniques and processing equipment have also influenced the design and now give the preparation engineer numerous permutations in process and equipment selection. This paper gives an overview of the coal industry in general and summarizes some of the developments in the design of plants and technical developments in the areas of dense medium processing, fine coal treatment and equipment design.

Jan 1, 2003