Search Documents

By M. Kumaran, A. Vetriselvan, A. Purantharan

"This paper presents a case history of evaluating the stability of a distressed earth bund and rectification measures carried out. A 5.45 km long, 7m high earth bund for drinking water storage was constructed in Andhra Pradesh. During construction of the bund following were observed – (a) a longitudinal crack at the downstream side (b) Bund on the downstream side along the crack settled to a max of 700 mm and (c) downstream rock toe level area raised by heave up to 175 mm. Investigation of the events made important contributions to the fundamental understanding of the behaviour of large earthworks of this type. It was found that the variation in subsoil strata was not addressed during the execution.After careful evaluation, stone columns were recommended as a suitable ground improvement technique. Stone columns were used as a reinforcement to improve the shearing resistance of foundation and in turn ensure stability. By using and applying advanced geotechnical engineering analysis tools and modelling techniques, earth bund and its foundation was analysed and examined against failure by slope instability. Stone column design was carried out using in-house computer program GEOSTONECOL and stability of earth bund was analysed using TALREN software. Earth bund construction was completed after ground improvement and is performing satisfactorily.INTRODUCTIONIn order to supply water during summer season, Government of Andhra Pradesh decided to construct a 7m high and 5.45km long earth bund summer storage tank. It was one of the largest earth bund summer storage tanks in whole of South India at the time of its construction. During construction, the earth bund has undergone sudden distresses. Investigation of the series of events occurred during construction has made important contributions to the fundamental understanding of the behaviour of large earthworks of this type. This paper presents the reasons for earth bund failure, slope stability assessment of the distressed earth bund and recommendation of stone column as a suitable ground improvement remediation technique.DESCRIPTION OF STUDY SITEThe characteristics of the original construction are briefly described as follows. A shallow cut-off trench was excavated below existing ground level at the centreline of bund as shown in Fig. 1. Below the base of the trench a cut-off grout curtain was installed. Upstream and downstream shell earth filling was carried out using Clayey Sand ‘SC’ type soil. At some locations, bottom of cut-off trench has reached as deep as 12m from the existing ground level."

Jan 1, 2017

By C. Gherghel

The planning and operation of ventilation network systems for uranium mines require special considerations since ventilation is the primary technique of controlling ambient concentrations of radon progeny. The major environmental challenge facing the ventilation engineer is the requirement to dilute radon progeny to below the Working Level Month per year of worker exposure required by law. The application of large airflow volumes and the utilization of low residence times constitute some of the factors considered by the design engineer. Good mine planning and sequencing are also critical for protecting the health of miners. The mine ventilation must have such characteristics as flexibility, high air distribution efficiency, rapid air transit times, zero recirculation and no short-circuiting. A well established maintenance program for all ventilation appliances must be in place to guarantee control of the distribution system. Real-time monitoring systems permit assurance the adequate quality of air is delivered to working places. A case study for an operating mine is used to demonstrate how the ventilation system is successfully managed and operated using the above concepts.

Jan 1, 2009

By A. A. Sadegh

A laboratory investigation was carried out on the characterization and beneficiation of sillimanite ore. Petrographic analysis indicated that the ore consisted of massive elongated sillimanite grains in a matrix of hematite, garnet, feldspar and silica. A procedure for estimating the percentage of sillimanite was developed using float-sink and magnetic-separation techniques. A liberation study was carried out to determine the level of size reduction required to achieve sufficient liberation while ensuring that gravity concentration techniques would be applicable. Laboratory testing was performed on the liberated ore to investigate the applicability of using wide-angle dense-medium cycloning to upgrade this ore. Initially, medium-only tests were carried out using various size distributions of magnetite and ferrosilicon as the dense-medium solids to evaluate the effects of operating conditions on medium segregation. Depending on the medium solids and operating conditions, either positive of negative differentials (difference between the relative densities of the underflow and overflow streams) were obtained. Based on these results, separation tests were performed to process nominal -1.2-mm sillimanite ore. The results indicated that sillimanite concentration could be obtained using a medium relative density that was much lower than would typically be used in a dense-medium cyclone separation.

Jan 1, 2007

In 2009 Newmont Mining Corporation?s annual global spend on grinding media reached $94M USD, having doubled in the five years since 2004. The major contributing factor to the spend escalation during this period was unit consumable price, with total media consumption also rising as a function of annual ore tonnes milled. In an effort to better understand and manage the growth of this expenditure a significant supply chain management program was implemented. This was complemented by a series of technical initiatives focussed on grinding media specifications, quality management and the prediction of grinding media wear rate as a function of physical ore characteristics. This paper discusses the methodology and outcomes of these activities.

Jan 1, 2012

The goal of the Bureau of Mines diesel engine research program is to reduce exhaust emissions and minimize the risk of fires and explosions caused by the use of diesel- powered equipment in underground mines. This program has led to a fundamental understanding of the problems and to solutions that allow diesel equipment to be used safely and effectively. This volume contains reports of the presentations made at the Bureau Technology Transfer Seminar on Diesels in Underground &fines given in Louisville, KY, and Denver, CO, on April 21 and April 23, 1987. It also contains three reports of related research, not presented at the seminar, which highlight the significant achievements of a joint US.-Canadian research program on diesel emission control technology for underground mines. Topics covered in this volume include discussions of industrial hygiene problems associated with the use of diesels, accident statistics, fire and explosion control systems, measurement of diesel pollutants, emission control techniques including engine maintenance, fuel additives, diesel particulate filters, and ventilation of diesel sections. An alternative to diesel power, the hydrogen-powered mine vehicle, is also described.

Jan 1, 1987

By John P. McDonnell

Cable supports offer several advantages over traditional secondary support methods by enhancing stress redistribution to pillars and gob areas, minimizing or eliminating timbers and cribs that reduce ventilation, eradicating material-handling injuries related to placement of crib supports, and providing a cost-effective alternative to secondary support. The U.S. Bureau of Mines, in researching alternatives to traditional roof support methods, designed and installed high-strength cable supports to improve the stability of longwall gate road and bleeder entries in a Western U.S. coal mine. With the cooperation of industry, methods were developed to install cable supports in a tailgate and bleeder entry test area using traditional resin cartridges. Resin-grouted cable bolts were also installed and evaluated in additional longwall gate road and bleeder entry systems at the study mine. The cable-bolted areas successfully maintained roof support throughout the tailgate and bleeder entries. Cable supports replaced wood cribbing as secondary support in the bleeder entry system and minimized the use of cribbing in the longwall tailgate entries. This report describes the theory, application, and advantages of cable supports and presents mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 2010

By Lawrence H. Van Vlack, Alfred S. Keh

The distribution of sulfur in iron was found to be dependent upon the time and temperature of the treatment as well as the chemical composition of the sulfide. With higher temperatures, the sulfide phase spreads more extensively between the iron grains. A complete network, however, does not form until approximately 1300°C (2372°F), ot which temperature the dihedral angle approaches zero. Silicon has little effect on this change. Aluminum, oxygen, and manganese all modify the temperature of sulfide network formation to a higher value. The microstructures which result and have significance in relation to hot-shortness are discussed. SULFIDE inclusions in steel were recognized by metallurgists before the turn of the century. Considerable attention has been paid to them, and numerous studies have been made on the working properties of steel as affected by them. It has been suggested that ho t-shortness of steel is due to the presence of an enveloping liquid sulfide film at the grain boundaries of the steel in the range of the hot-working temperatures. However, several facts have been observed in commercial steels which do not seem to be completely consistent with this explanation: 1) the frequent absence of continuous films of sulfide as observed under the microscope, 2) the absence of hot-shortness in some high sulfur and resulfurized steels, and 3) the limitation of hot-shortness to a definite temperature range. The role that manganese plays in steel to eliminate hot-shortness is well known, but the theory behind it is still under question. Moreover, the effect of de-oxidizers such as aluminum and silicon, and the effect of oxygen are still not clearly known. In this study, the effect of heat treatments and of additions of manganese, aluminum, silicon, and oxygen upon the distribution of sulfide inclusions in iron was investigated. Both the as-cast and the heat treated structures were studied, using microscopic and autoradiographic techniques. Part of the results were interpreted in terms of Smith's' concept of microstructure. Review of Literature Metallurgists used to consider sulfide inclusions as suspended particles. It was Wohrman' who first pointed out that sulfide inclusions are soluble in liquid iron. Many observed facts may be understood on the basis of this concept of solubility. Wohrman found that small castings contain small inclusions. and larger castings contain larger ones. Also, inclusion sizes are smaller near the chilled surface. For the same size ingot, the average inclusion size in a given heat of steel depends upon the rate of solidification. That is, with slow solidification, enough time for precipitation and agglomeration of these

Jan 1, 1957

By M. F. Dunn

The objective of this work was to define jet fan performance in d variety of large cross-section underground mine applications and to develop guidelines for thin performance in open airways, dead headings, and multiple face areas. Measurements include common ventilation instruments, continuous recording remote electronic anemometers to measure air velocity, and sulfur hexaflouride tracer gas with chromatograph analysis to determine dilution rates and air recirculation. For open airways the following were determined: Large jet fans are leas efficient in smaller airways, but quite effective in larger open airways for achieving both uniformity end greater air entrainment, when inclined about 10° or elevated. For dead headings the following were determined: The jet fan must be placed against the rib of the heeding closest to the incoming airstream from the crosscut or recirculation will increase. The fan should be placed at the pillar corner to increase airflow. As the fan is moved closer inby, recirculation increases. Larger fans promote recirculation. Inclining fans about 12° improves airflow in large headings. For face areas the following were found: For panels having uncontrolled airflow, the fan should be placed in the incoming airflow, about one pillar inby, and directed diagonally across the faces. For panels having narrower rooms and controlled airflow, the fan should be placed alongside the panel side in the first room so as to direct or intersect the incoming airflow at the next entry or crosscut.

Jan 1, 1983

By A. Eccles

Phase designs are the foundation upon which all open pit mine sequence optimizations and budgets should be built. Unfortunately, at times, mine engineers skip the step of developing realistic pit phase designs - designs that include access ramps and mineable widths. Without mineable phase designs, their optimized schedules are based on theoretical pit shells or ?quick-and-dirty? plans with no ramps. The output from such optimizations is almost always overly optimistic. Without mineable designs, the production estimates are misleading, because they overestimate ore, and underestimate waste stripping requirements. Worse yet, when plans are not based on realistic phase designs, they can point to exactly the wrong decision in feasibility studies (i.e. ?go? when it should be ?no-go?). This paper discusses the importance and features of good pit phase design, and demonstrates the pitfalls of relying on optimized production sequences that are not based on properly designed pit phases.

Feb 27, 2013

The inherently explosion-proof mine (EPM) concept is based upon the non-flammability of certain combustible-oxidant-inert gas mixtures, and the effect of partial pressure of gases on physiological reactions. In a properly controlled underground environment, gas explosions are impossible, men can do work, and relatively high concentrations of methane would be permitted. A systems analysis has been performed to examine the physiological, engineering, and economic feasibility of such a concept, and methods and equipment are recommended for maintaining an EPM atmosphere in a bituminous coal mine producing a nominal two million tons of clean coal per year. It is concluded that: engineering feasibility can be demonstrated using subsystems and components that can be designed and built within the present state-of-the-art, that economic feasibility is possible within approximately five years, and that physiological feasibility is sufficiently promising to warrant continued investigation.

Jan 1, 2012

Although not immune from the problems affecting the U.S. economy generally, the mineral industry in 1991 contributed nearly $300 billion in the value of processed materials of mineral origin. Supporting this contribution, the Bureau of Mines continued the research and analytical programs highlighted in this annual review. Featured in 1991 were such relatively new programs as minewide monitoring applications in ground control and advances in processing of ceramics and composites, along with more traditional research into health, safety, and mining technology, minerals and materials science, and environmental technology. Under Bureau sponsorship, a National Minerals Policy Forum brought together some 200 executives from industry and Government concerned with minerals policy to begin a dialogue on developipng a policy statement on current minerals issues. A major feature of the forum was the keynote address by Secretary of the Interior Manuel Lujan, Jr.

Jan 1, 1992

This Bureau of Mines report and its companion report (Information Circular 9142) have been prepared to assist in the preparation of prefeasibility type estimates for capital and operating costs of beneficiation of various types of mineral occurrences using current technology. The handbook provides a convenient costing procedure based on the summation of the costs for the unit processes required in any particular mining or mineral processing operation. The costing handbook consists of a series of costing sections, each corresponding to a specific mineral processing unit process. Contained within each section is the methodology to estimate either the capital or operating cost for that unit process. The unit process sections may be used to generate, in January 1984 dollars, costs through the use of either costing curves or formulae representing the prevailing technology. The mineral processing handbook includes individual cost estimation sections for unit operations associated with comminution, beneficiation, solid-liquid separation, hydrometallurgy, and special applications as well as infrastructure and plant general and administrative costs. When using this system for estimating cost data for a mineral processing facility or for checking or verifying processing costs from an existing facility, a minimum amount of background information is necessary.

Jan 1, 1987

By R. W. Courtney

The objective of this study is to make a critical evaluation of the magnitude and extent of electrostatic hazards in typical U.S. mining operations and to assess the adequacy of techniques, materials, and equipment for detecting and minimizing these hazards. This was accomplished with an incident/accident survey, mine visits, literature search, and engineering analysis. It was concluded that it would be desirable to (1) utilize ground fault interrupters to minimize stray current from electrical utilities, (2) decrease the current and electrostatic sensitivity of electric detonators used in areas with a high incidence of lightning strikes or troublesome stray currents, (3) institute quality control and test standards for blasting material and protective devices, (4) establish an electrostatic monitoring program for loading ANFO in plastic lined holes, and (5) establish a risk criteria for operator exposure in mines.

Jan 1, 1982

This study assesses whether Narragansett Basin coal deposits could be developed commercially in the near future. To do this, we identify the potential market for the coal, assess the price these users would be willing to pay for Narragansett coal, and this price to the expected costs of producing Narragansett coal. The study concludes that the major market, New England utilities, could burn bituminous coal from Pennsylvania or West Virginia at a lower total cost than Narragansett Basin coal, assuming expected mining conditions and emission policies. Therefore, the study concludes that Narragansett Basin coal resources could not be developed economically in the next ten years.

Jan 1, 1979

By R. H. Fernald, C. D. Smith

When the United States Geological Survey began operations at the coal-testing plant erected at the Louisiana Purchase Exposition at St. Louis, Mo., in 1904, it had already outlined a comprehensive plan for the systematic study of coals, lignites, and other mineral fuels with reference to their suitability for particular purposes and the methods by which they could be utilized most efficiently. Recognizing the need of information on the relative economy of producer gas as compared with steam for power purposes and the lack of comparable tests of American coals in the gas producer, the Geological Survey undertook investigations of the merits of different coals as producer fuel for the purpose of promoting efficiency in the utilization of the nation's fuel supplies. These investigations were carried on at St. Louis, Mo., and, later, at Norfolk, Va., and Pittsburg, Pa. The aet of Congress approved May 16, 1910, transferred the fueltesting work being carried on by the Geological Survey to the Bureau of Mines. This bureau is conducting producer-gas tests at P~ttsburg, Pa., and is publishing and distributing reports relating to all the fuel tests made by the Survey. These investigations into the possibility of generating producer gas in a commercial way for power purposes from the various fuels of the country have been associated with steaming, briquetting, coking, and other tests, all of which supplemented an examination into the nature, extent, and distribution of the fuels. The tests have all been made with carefully selected representative samples and carload lots of materials procured specially for the purpose by experienced collectors.

Jan 1, 1911

By Cory G. Rice

A significant portion of the piling industry has long felt relying on soil setup to gain the required capacity is a complexity that would rather not be dealt with. Instead, the pile are driven to the required capacity on the initial drive and the potential gain of capacity due to soil setup is simply considered an added bonus or safety factor. There appears to be an attitude that if one did not put in the energy required to develop the full capacity on the initial drive, then one should not expect to gain anything from Mother Nature for free. However, substantial savings in time and materials can be realized by properly accounting for setup. This paper will show the impacts and ramifications this rationale can have on required labor and material costs and illustrate a case history with significant soil setup and the savings realized on a project currently being constructed.

Jan 1, 1992

By H. W. Earnest

This report covers the results of a two-phase study to determine the feasibility of underground disposal of retorted oil shale. Two mining methods, chamber and pillar mining and sublevel stoping, were specified for backfilling. Phase I of the study covered the evaluation of hydraulic, mechanical, and pneumatic transport and stowing systems, individually and in various combinations, and the selection of the most feasible methods. Conveyor transport and stowing and a combination conveyor transport and stowing with pneumatic topfilling were selected for detailed study of phase II. Phase II activities included detailed engineering analysis and design of the selected systems, an engineering economic analysis, and a cost comparison with total surface disposal of retorted oil shale. An extensive literature search was conducted and the bibliography is included in the report. Research done under Contract No. J0265052 by the Cleveland-Cliffs Iron Co. Available for reference at Bureau of Mines facilities in Denver, Colo., Twin Cities, Minn., Bruceton and Pittsburgh, Pa., and Spokane, Wash.; U.S. Department of Energy facilities in Carbondale, Ill., and Morgantown, W. Va.; National Mine Health and Safety Academy, Beckley, W. Va.; and National Library of Natural Resources, U.S. Department of the Interior, Washington, D.C. Order ONLY from NTIS:

Jan 1, 1978

By P. A. Cox

The purpose of the initial research performed under this contract was to determine the margins of safety in explosion-proof (XP) enclosures, which were designed and certified according to the current schedule (Schedule 2G). Results from this work provide baseline data on the current schedule, from which a new schedule can be formulated to give equal or greater levels of safety. Results and discoveries in the initial work led to an expansion of the contract to cover, additionally, weld quality in enclosure fabrication, reliability of enclosures with windows and lenses, and performance tests for enclosure qualification. Finite element calculations and hydrostatic tests revealed wide variations in the margins of safety in the enclosures studied; however, only one enclosure had a safety factor which was less than one. Results from a weld quality survey led to the recommendation of AWS Welding Standard D14.4 for the fabrication of XP enclosures. Based on other work, accelerated aging tests were recommended for qualifying plastics and adhesives that are used in some enclosures, and a Structural Performance Test was developed to test enclosure strength for a minimum static pressure of 150 psig.

Jan 1, 1982

By G. W. Josephson

WHILE methods of utilizing blast-furnace slag have been developing, a great deal of literature on the subject has accumulated, but no comprehensive summary of information that would be helpful to engineers, contractors, architects, chemists, and others in under-standing and more successfully using this byproduct of the iron and steel industry has been published in the English language. The National Slag Association recognized the need for such a publication, and the Problems Committee of the Association under-took in 1943 to accumulate the necessary material. Over a period of several years this committee compiled pertinent information in manuscript form, and in 1948 the Bureau of Mines and the National Slag Association made an agreement whereby the Bureau was to prepare the data for publication as a cooperative bulletin of the Bureau of Mines and the National Slag Association.

Jan 1, 1949

By Jannie van Deventer

"Innovation in the minerals industry has been lagging behind comparable industries like oil and gas. An incremental innovation culture that tolerates long lead times between invention and adoption has been exacerbated by a research grant structure that inhibits radical idea generation. Entrepreneurs who can make the link between ore source, technology and finance will cause a shift in innovation culture and open up substantial opportunities in the minerals industry of the future. By extrapolating existing trends in technology within and outside mineral processing, a crystal ball vision of future innovation is shaped with the aim to lower energy and water demand, reduce CO2 emissions, decrease operating and capital costs, reduce environmental impact, and secure a social licence to operate. Advances in nanotechnology, advanced materials and biotechnology will impact mineral processing, but the initiative for technology transfer must come from mineral processors. Laminates of graphene oxide can offer efficient filtration and separation media, while microfluidic devices will be used for desalination, solvent extraction and analysis. Substantial progress is expected on benign lixiviants and separation agents, such as nanoscale supramolecular hosts that can serve as high-capacity, selective and recyclable ligands and sorbents, and solid aminobiphosphonate-based adsorbents. Radical ideas for the recovery of precious metals from non-assayable ores and the generation of energy above unity will be adopted in selected minerals projects. In-situ mining in which microbes generate lixiviants at mineral surfaces will simplify processing circuits. Specific ores will be subjected to microwave processing and electropulse liberation to enhance recovery. Ultrafine grinding using devices of low energy consumption will be done mainly dry, followed by dry separation. New flotation cells will remove efficiently either coarse particles or ultra-fine particles, with mineral surfaces being modified not just by new reagents but also by selective microbes. Innovation in mineral processing indeed has a bright future."

Jan 1, 2014