Search Documents

By V Matousek, A Sellgren, R Visintainer, G McCall

A 4-component model for settling slurry pipe flow has been previously described by Wilson et al (2006) and Sellgren et al (2014) to predict pipeline friction loss (hydraulic pressure gradient) over a range of slurry compositions: from fine to coarse particle size, narrow to broad particle size distribution, and low to high solids concentration. The method applies a weighted average of established pipeline models for various settling slurry flow regimes, according to the volume fraction of solids falling within the applicable size range for each model. Further development of the model was undertaken by Visintainer et al (2017a, 2017b), based on a comprehensive set of laboratory tests in 203 mm (8 inch) and 103 mm (4 inch) pipelines, and it was also adapted to the modelling of slurry pump performance derates. However, this work was all performed with solids having a specific gravity near 2.65, as is typical for many mineral processing and dredging applications. The goal of the present work is to test the applicability of these models for settling slurries having a higher solids specific gravity, as may often be seen in the mineral processing of iron ore deposits. To that end, a test program was carried out in a 103 mm (4 inch) pipe loop using various compositions of an iron ore product having a solids specific gravity of 4.75 and containing both coarse and fine solids. By screening and flushing operations, a range of particle size distributions were created having different proportions of the coarse and fine elements. In all, 19 tests were performed with d50 particle sizes ranging from 50 μm to 3.2 mm and delivered solids concentrations from 10 per cent to 43 per cent by volume. Particle size distributions varied from very narrow to very broad, with d85/d50 ratios ranging from 1.75 to 26. Pipeline pressure gradient and pump performance data were collected and used to test the applicability of the previously developed 4- component models and to propose improvements to the models for the handling of high-density solids.

Nov 8, 2021

By Joan Weinberg

The real gross national product (GNP) expanded by 2.3% during the second quarter, down from the anomalous 4.4% growth rate in the previous 3 months. If the expansion continues through October, it will have lasted 5 yr and become the second longest in 40 yr.2 As in the first quarter, improvement in U.S. exports played a role in the continuing--albeit slow--growth. More than 2 yr of declines in the dollar relative to currencies of other industrial countries have contributed to a slight reduction in the trade deficit in real (volume) terms, as real net exports of goods and services rose $1.9 billion (table 1). Exports grew a strong 12.1% while imports, which had fallen the previous two quarters, rose 7.4%. Manufactured goods and petroleum products accounted for most of the second quarter import increase. The American Petroleum Institute estimates that the volume of crude oil and refined products imports in the first half of 1987 surpassed those in the same period last year by 7.5%, reflecting falling domestic production and higher than expected demand. Expenditure on durable goods--those that last at least 3 yr-by both consumers and producers also contributed to the second quarter expansion. Personal consumption of durable goods rose 9.0%, after having fallen the two previous quarters. Motor vehicle purchases accounted for most of the second quarter increase and the first quarter decrease. Sales of automobiles surged in the last quarter of 1986, as consumers rushed to capture the sales tax deduction that was eliminated on January 1. Sales fell in the first quarter of 1987, but have now moved closer to the trend line exhibited in the first three quarters of 1986. Automobiles accounted for half the 0.8% July gain in retail sales, and two-thirds of the 1.4% June gain. Producers durable equipment purchases also rose this quarter, accounting for the increase in nonresidential fixed investment.

Jan 1, 1987

"1.0 INTRODUCTIONThese Guidelines reflect the state-of-the-practice of the Deep Mixing Method (DMM) in North America. DMM is an in situ mixing process that breaks down the soil structure; injects binders, fillers and reagents into the soil; and blends them with the soil. DMM is also commonly referred to as Soil Mixing. The final properties of the treated soil in situ are a function of the composition of the native soils and groundwater, the binders introduced, the mixing methods and energy, and the conditions and time of curing. Treated soils generally have increased strength and stiffness and/or reduced permeability relative to the native soils.This document addresses DMM performed by rotating single and multiple axis mixing tools, rotating cutter wheels at the end of a rigid kelly bar, or trench mixing using a rotating cutting/mixing chain around the perimeter of a rigid bar. Binder may be injected through low or high energy (velocity) jets.The treated soils created through wet DMM are heterogeneous mixtures of binder, water, soil, and groundwater. Treated soils produced by dry DMM techniques are a mixture of binder, soil, and the water already present in the native soil.DMM applications described in this document include•,Earth retention•,Liquefaction mitigation•,Groundwater seepage control and containment isolation•,Bearing capacity improvement•,Deep foundations•,Mass stabilization and contamination containment•,Embankment, levee and dam strengthening, and stabilization•,Casing replacementThis document was developed to address deep foundations applications. Use of deep mixing for seepage control is not specifically addressed. The reader is referred to documents prepared by the U.S. Army Corps of Engineers for additional information. Shallow soil mixing and the use of DMM for stabilization/solidification of contaminated soils performed at depths less than 10 feet (3 m) are mentioned briefly. Jet grouting is not covered by these guidelines."

Jan 1, 2016

By R. L. Virta

Four companies ? H.C. Spinks Clay Co., Inc., Imerys, Old Hickory Clay Co., and Unimin Corp. ? mined ball clay in four states in 2013. On the basis of preliminary data, production was 1 Mt (1.1 million st) with an estimated value of $47 million. Production increased by 3 percent in tonnage from 973 kt (1.1 million st) with a value of $45.1 million in 2012. Tennessee was the leading producer accounting for 64 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 67 percent of total ball clay production was airfloat, 22 percent was crude or shredded and 11 percent was water-slurried.

By L. K. Walker, G. A. Kosick, P. D. Young

"MillEX is an information management system designed by mineral processors for mineral processors. The system utilizes ""cutting edge"" software technology to gather and store all automatically and manually recorded data from the plant operation and laboratories. This data is delivered to the desk of superintendents, metallurgists, technicians and managers, and permits the user to query, correlate, graph, report and present this data in minutes. In the past this task would have taken days and even weeks of tedious work to complete.MillEX allows the engineer/analyst to quickly develop a very thorough understanding of the complex relationships of process variables and equipment that exist in the plant, and their effect on product quality and quantity. The time and resources that are currently wasted on duplicating data entry will be an effort of the past.This paper describes the structure of MillEX and how it conforms to the needs of mineral processing personnel.INTRODUCTIONPicture a personal computer on your desk which will carry out the following commands:1. Plot a graph over the last six months, using weekly averages, of percent minus 200 mesh material in the primary cyclone overflow.2. Overlay this graph with a graph of concentrate grade versus recovery over the same time period.3. Retrieve a prior month end report, update all operating supplies tables and metallurgical performance with this months data, and embed the graphs created above.4. Edit text and print the current month end report. This is only one example of the type of power MillEX isbringing to the mineral processing industry."

Jan 1, 1992

By D. Eastick, S. Hardcastle

"Over the last few years, a multi-faceted feasibility study has been evaluating the introduction of hydrogen fuel cell-powered equipment into underground mines to replaced diesel engine-powered equipment. The analysis has shown that under normal operating conditions fuel cells could at the very least be an environmental and health benefit by eliminating combustion engines and their unwanted by-products. However, they could also generate significant reductions in the amount of ventilation a mine needs to supply when compared to dieselized operations; this would further decrease a mine’s energy consumption, its associated greenhouse gas impact, and also reduce a mine’s significant ventilation-associated costs. Fuel cell-powered equipment also has the advantage of lower noise and heat production compared to its equivalent diesel-powered counterpart.The degree to which fuel cells can generate ventilation benefits in underground mines depends upon a number of operational parameters and mine specific qualifiers such as current ventilation control or management, mine depth, inherent dust conditions, and minimum velocity requirements.However, another major consideration in the introduction of fuel cells in underground mines will be the safety requirements associated with diluting and removing the potentially explosive hydrogen in the event of a gas leak. In outside surface applications, it is possible to use dispersion, buoyancy, time, and lack of ignition sources as mitigating factors in deriving a low risk of an explosion. However, in underground operations, these factors change, and dispersion and buoyancy are limited; time may not be available and, in non-coal mines, ignition sources are not typically controlled. When a hydrogen leak occurs, the availability of sufficient ventilation to dilute and effectively remove the gas will be critical. Consequently, ventilation may be the prime risk controlling factor. In this paper, the authors evaluate the potential benefits of replacing diesel engines with fuel cells in powered production equipment, discuss the mitigating qualifiers that could limit ventilation savings, and evaluate solutions to retain and maintain an additional ventilation capacity in the event of an emergency situation, such as a hydrogen leak from the fuel cell stack or its distribution system."

Jan 1, 2007

By Paul T. Alexander

After evaluating preceding studies and designs of lightweight supports, ESD selected the all-hydraulic and the hydromechanical concepts for detailed design and fabrication. Further analysis and testing showed that the all-hydraulic design was economically justified and met all the crucial engineering, manufacturing, and design criteria identified during the evaluation phase. Following Bureau of Mines approval of the detailed design, four all-hydraulic support models were fabricated. Once functional and structural testing was successfully completed, 40 additional units were constructed and distributed for in-mine testing. The units were very well-liked by all three demonstration mines. The wide- spread interest in supports for seam heights greater than 8 feet led to expansion of the design data package. ESD designed four basic models to cover the new height range, but no hardware has yet been fabricated for the new design.

Jan 1, 1982

By J. R. Thoenen

This circular is the second of a series presenting methods employed in solving the technical problems encountered in the production of sand and gravel. The first paper3 discussed the methods use in prospecting and exploration. This one teals with the problems involved in bringing a raw prospect to the production stage and considers the various methods of development and the Factors affecting that development. Later publications are planned to present and discuss methods of recovery and treatment. The recovery of sand and ravel from natural deposits and their preparation for market involve a progressive sequence of operating steps or processes. Each step or process presents its own peculiar problems which require different angles of mental approach, methods, and tools, but all are more or less dependent on the step or process which precedes or follows.

Jan 1, 1933

By W. R. Hardwick

This Information Circular describes the development of block-caving methods and practices by the Miami Copper Co. at the Miami mine in Gila County, Arizona. It is one of a series published by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. This report gives a history of the district and outlines early prospecting and exploration including methods of sampling and estimation of ore tonnage and value at the Miami mine. Early mining methods are described, particularly those that influenced developments in the caving method. Mine exploration, development, and operating methods for block caving are described with particular attention to those factors, physical, economic, engineering, and managerial that have improved efficiency in the mining operations over a long productive period. Extraction, ventilation, wage system, safety, water supply, power plant, and shop facilities are discussed. The last section gives a brief sumary of such costs as are available for publication.

Dec 1, 1964

These proceedings consist of papers presented at three Bureau of Mines Technology Transfer Seminars on ergonomics in the mining industry. These seminars were held in December 1981, and covered topics relating to ergonomics and mining in the areas of the man-machine interface, and design of the work environment. This area of research is directed toward reducing accidents traditionally associated with human error.

Jan 1, 1981

By H. B. Hill

The Lake Creek gas-condensate field, Montgomery County, Tex., Was discovered early in 1941 by the Superior Oil Co. The field, shown in figure 1, is approximately 37 miles northwest of Houston, Tex., about 11 miles north of the Tomball, and 10 miles west of the Conroe oil fields. The field is on the downthrown side of a pronounced fault zone, and the general structure is anticlinal, with the long axis trending northeast and southwest. Production is obtained from multiple sandstone reservoirs in the Wilcox group of Eocene age between the approximate depths of 8,820 and 11,840 feet below the surface of the ground.

Jan 1, 1948

By D Bertoldi, C Haines

"The Waihi Gold Mine (WGM) operated by OceanaGold New Zealand Limited is a wholly owned subsidiary of the OceanaGold Corporation of Australia. Traditionally WGM has stockpiled and processed separate campaigns of open pit and underground ore. The ore is processed via a conventional semi-autonomous grinding (SAG) / ball circuit (SABC). The low aspect SAG mill operates in a closed circuit with two 20" cyclones, whilst the ball mill is also a closed circuit with a 10" cyclone cluster. A major wall movement in April 2015 ceased open pit operations indefinitely, 18 months ahead of the mining plan. This immediately reduced the forecast mill tonnage leaving two options: begin campaign milling or change the operating strategy and target lower throughput. Additional cost pressures necessitated improved milling cost efficiency. The immediate ore restriction limited processing alternatives to within the existing major infrastructure. Available comminution circuit survey data laid the foundation for developing a comminution model using the JKSimMet™ software package (version 6, created by KJTech). A number of flow sheet variants were then evaluated based on predicted throughput and efficiency. The comminution models suggested opportunities for improved efficiency lay in reducing throughput and increasing utilisation rather than on/off campaign milling under the existing operating philosophy. A series of process alterations followed, delivering new cost efficiencies that maintained the current $/t processing cost. This paper aims to review the change in circuit performance and examine the decisions and challenges faced following the transition from a high tonnage SABC circuit to lower tonnage SABC circuit.Citation:Haines, C and Bertoldi, D, 2016. The Transition from Semi-autogenous to Autogenous Milling at Waihi Gold, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 303–312 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By V. Ferrari

This report documents the three-phase program to design, fabricate, test, and demonstrate economical and practical methods of reducing noise levels on underground coal mining portal buses (mantrip vehicles). The noise-control treatments applied to a production-model portal bus were as follows: ? Wheel/rail vibrations were isolated from the vehicle frame by inserting elastomeric materials between suspension components. ? Vibration-induced noise was reduced by replacing all large sheet metal panels (except floor plates) with damped steel panels. ? Motor noise was reduced by tight-fitting covers made from damped steel and lined with sound-absorbing material, and by elastomeric motor mounts. ? The standard spur gears used in the traction drive system were replaced with helical gearsets. The program achieved the goal of reducing the average sound-level to below 85 dBA for typical operating conditions.

Jan 1, 1981

By P. J. Mackey

Over the course of Dr. Robertson’s career, the ferrous and non-ferrous plants have seen enormous changes in technology and increases in plant capacity, essentially amounting to a “technological revolution”. In iron and steel, the “mega” blast furnace of some 6,000 m3 working volume is now standard (~10,000 tonnes (mt) of pig iron/day). Similar huge changes in process technology and plant size have occurred in the non-ferrous industry. As an example, the fuelfired reverberatory furnace, once the mainstay of the copper industry, has disappeared - replaced by large capacity flash and bath smelting technologies. The energy consumption per unit mass of metal produced has also been reduced considerably. Our understanding of the thermodynamics and mechanisms of metallurgical reactions, a field to which Dr. Robertson has significantly contributed, has made great strides. This paper reviews these changes with particular reference to the copper smelting industry, providing also comments on expected future trends.

Jan 1, 2014

By B. P. Nutter, M. Lebourg, J. A. McAlister

The Multi-Flow Evaluator (MFE) is a new system of tools providing an original approach in drill-stem testing. It improves control during the testing operation and gives a more accurate evaluation of the fluid recovered while providing additional pressure information for reservoir analysis. The tools are operated entirely by up and down motion of the drill stem. This up and down operation provides a positive means of control and offers easily observed surface indications of tool operating position. An unlimited number of shut-in and flow periods may be taken with this tool while in the hole. The key to the success of the MFE system of tools is the safety seal packer. Until this development, operation of the tools by up and down motion only had proven unreliable. The success ratio of the MFE now exceeds the ratio achieved by conventional tools. The equipment includes a 2,750-cc chamber in which a representative sample of the flowing formation fluid is trapped at the end of the last flow period and brought to the surface under pressure. The sample can be evaluated at the wellsite or transferred under pressure for laboratory analysis. The sampling feature of the tool allows a sample to be obtained from a reservoir which has suffered minimum influence from production. A representative sample can be obtained for laboratory or empirical analysis by employing a testing technique to minimize drawdown during flow periods. Interpretation methods to take advantage of this additional information are presented and supported by actual field examples. INTRODUCTlON The Multi-Flow Evaluator (MFE) represents the most recent technical advance in formation testing. Drill-stem testing techniques prior to the MFE have been limited in three areas—(1) operaiion, (2) recovery analysis, and (3) reservoir analysis. The tools in the MFE system allow maximum control during testing and provide test information superior to that obtainable with conventional tools. The system of tools and the operation procedures are described to illustrate the mechanical advantages over present tools. Methods of pressure build-up and fluid

Jan 1, 1966

By W T. C Kendall, H D. Ngo

Garden Well is a shear-hosted Archaean orogenic gold deposit located 100 km north of Laverton, Western Australia. The Garden Well processing plant is designed for a nominal 491 t/h milling rate and annual capacity of 4 Mt. The plant has three key innovations:1. a scrubbing circuit, expected to reduce grinding power consumption by up to 20 per cent2. a secondary cycloning/gravity circuit, providing a second opportunity for gravity gold recovery (additionally, the circuit effectively increases the leach residence time of the coarse gold bearing fraction of the leach feed by approximately 60 per cent, without any additional tankage)3. the use of mid-stream oxygenation to enhance gold recovery.The Garden Well deposit is free-milling with overall laboratory gravity/leach gold recoveries exceeding 95 per cent at a P80 grind size of 150 ¦m. Three mineralogical domains have been identified: oxide, transition and fresh, with the fresh domain having subdomains of fresh ultramafic and fresh shale. There is a high component of gravity recoverable gold in all three domains.This paper will discuss these innovations and the design challenges and the risk mitigation strategies that were adopted to ameliorate the prototyping risk. The performance of the plant since commissioning together with lessons for the future will also be presented.CITATION:Smith, R J, Kendall, W T C and Ngo, H D, 2013. Treatment plant innovation at Garden Well, in Proceedings World Gold 2013 , pp 315-324 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By A. Timur

Fluid flow properties of porous media have long been of interest in such varied disciplines as geology, geophysics, soil mechanics, and chemical, civil, and mechanical engineering. This interest has resulted in numerous models of porous media that have been proposed, tested, and found to be useful under, at best, only special circumstances. A critical review of most of these models is given by Scheidegger. 1 The application of each new tool to the study of porous media has helped to test some of the existing theories and to form new ideas based on the new parameters being measured. In the application of nuclear magnetic resonance (NMR) techniques to the study of the properties of fluids in porous media, the theoretical studies of Korringa et al.2 resulted in a model for the relaxation of spin polarization of protons in a hydrogenous fluid in a pore of a solid. Seevers3,4 verified this model, established a method for measuring the surface-to-volume-ratio distribution in a porous medium, and proposed a technique for determining specific permeability in sandstones. In the present investigation, the uses of NMR methods are extended and a simple model of porous media is developed from an analysis of pulsed NMR measurements. In this model, the pore spaces of a porous medium are divided into three groups on the basis of their surface-to-volume ratios. To evaluate predictions of the NMR model, laboratory measurements of spin-lattice relaxation time, porosity, permeability, and residual (irreducible) water saturation were conducted on more than 150 sandstone samples obtained from four oil fields in North America. Applications are discussed for estimating the volume of movable fluid, ?p, and the specific permeability, k, of sandstone samples. The former parameter, which can be considered as producible porosity, is expressed by ?p = [1 -- (Swr/100)]? , .... (1) where + is porosity in percent of bulk volume and Swr is the residual (irreducible) water saturation in percent of pore volume at a capillary pressure of 50 Psi. Fast, nondestructive laboratory methods are described for determining porosity, movable fluid, and permeability of sandstone samples from measurements with a pulsed NMR (spin-echo) apparatus. Procedures are given for adapting these methods to samples of irregular shape and small size. Theory General In the Korringa, Seevers, and Torrey2 (KST) model the observed decrease in the spin-lattice relaxation time, T1, of protons of a hydrogenous liquid contained in the pore spaces of a porous solid is attributed to an increase in the correlation time for the random motion of the water molecules and to the presence of paramagnetic centers at the liquid-solid interface. This KST model predicts the observed relaxation time of a hydrogenous liquid in a pore of a solid through

Jan 1, 1970

By T. J. Lutz, D. S. Yantek, L. Yan, J. R. Srednicki, J. A. Yonkey, G. T. Homce

Federal regulations require the installation of refuge alternatives in underground coal mines. Of the inuse refuge alternatives, more than 95 percent are mobile refuge alternatives, with the remainder being built-in-place (BIP) refuge alternatives. Heat/humidity buildup has been one of the major concerns with mobile refuge alternatives. For BIP refuge alternatives, however, there is a lack of in-mine heat/humidity test data to determine the extent of heat and humidity buildup. To quantify heat/humidity buildup in BIP refuge alternatives, the U.S. National Institute for Occupational Safety and Health (NIOSH) performed a series of heat/humidity tests on a 60-person BIP refuge alternative with and without a borehole air supply. At various times during the year, tests were performed with cooled, heated or unconditioned borehole air to examine how various outdoor temperatures may affect the thermal conditions inside a BIP refuge alternative. The results show that the air supplied to a BIP refuge alternative may require heating or cooling, depending on the outside air temperatures and the temperature of the mine. For example, during tests with an external ambient temperature above 21 °C (70 °F) and a relative humidity of 90 percent, providing 13 °C (55 °F) dew point air at 775 scfm, which is slightly higher than the mandated flow rate of 12.5 scfm per person, kept the internal apparent temperature below the mandated 35 °C (95 °F). Results for each test case are presented.

Jan 1, 2018

By Mackenzie Burnett

An inducer-type pump, capable of injecting dry coal into a hydraulic transport pipeline has been developed and installed in a specially designed and fabricated slurry injector vehicle. The full scale prototype injector system can deliver up to 11 ton/min of coal into an 8-in pipeline t pressures up to 95 lb/in2. The Helical Inducer Injector operates on centrifugal principles with flow passing axially through helical pitched conical rotor. Water is delivered to the pump through an annular slot at the atmospheric pressure coal inlet. The spinning rotor maintains an air-core vortex of water which pressurizes the discharge housing. A screw feeds coal through the open inlet into this vortex. The inner radius of the vortex contracts as pressure is increased, giving a limiting maximum pressure which is proportional to the square of the rotor speed. Below this limit, flow rate, discharge pressure, und rotor speed re independent variables. The self-powered, 4 -in high slurry injector vehicle follows and receives ROM coal from a continuous miner, reduces the top size to 3-in, and delivers the sized coal to the injector feed screw for slurry formation and pumps it through a mobile hose attached to the vehicle's outby end.

Jan 1, 1983

By Fred N. Kissell

This handbook describes effective methods for the control of mineral dusts in mines and tunnels. It assumes the reader is familiar with mining. The first chapter deals solely with dust control methods, regardless of the application. It is a brief tutorial on mining dust control and will be of help to the reader whose dust control problem does not conveniently fit any of the mining equipment niches described in later chapters. The subsequent chapters describe dust control methods for different kinds of mines and mining equipment. This includes underground coal and hard-rock mines, as well as surface mines, stone mines, and hard-rock tunnels. Because dust sampling has so many pitfalls, a chapter on methods used to sample dust is included. For those occasions when there is no practical engineering control, a chapter on respirators is also included. Except for those listed as ?future possibilities? in the longwall chapter, the dust control methods described are practical and cost-effective for most mine operators. If controlling dust were a simple matter, dust problems in tunnels and mines would have been eradicated years ago. Unfortunately, most underground dust control methods yield only 25% to 50% reductions in respirable-sized dust. Often, 25% to 50% reductions are not enough to achieve compliance with dust standards. Thus, mine operators must use several methods simultaneously, usually without knowing for sure how well any individual method is working. In fact, given a 25% error in dust sampling and day-to-day variations in dust generation of 50% or more, certainty about which control methods are most effective can be wanting. Nevertheless, over the years, some consensus has emerged on the best dust control practices. This handbook summarizes those practices.

Jan 1, 2003