Search Documents

By D. R. Taylor

The use of clay granules as carriers for pesticides dates from the early 1940's and by the present day represents a business conservatively estimated at between 200 -300 thousand tons / year in the U.S. alone. Aside from economic and specific target pest efficacy advantages, the use of clay granules as pesticide carriers also delivers a number of environmental benefits which will be reviewed. Topics to be discussed will include: I) drift control (versus liquid sprays), 2) mobility (in the environment), 3) worker safety, and 4) transportation (spill) safety.

Jan 1, 1999

By JOHN R. HEBERGER, MAHIYAR F. NASARWANJI, Jonisha P. Pollard, Lydia M. Kocher

nt in the mining industry, and identifying factors associated with these injuries is critical for developing prevention efforts. This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011 to 2017. Hand and finger injuries occur at a rate of 6.53 per 1,000 full-time employees, which is nearly double the rate of the next highest affected body part, the back. Most of the hand and finger injuries were classified as cuts/lacerations/punctures (53 percent) followed by bone fractures/chips (26 percent). Materials handling and maintenance/repair were common activities at the time of the incident with miscellaneous metals — such as pipe, wire and guarding — and hand tools as the primary sources of hand and finger injury. Although the information on glove use was limited, leather gloves were most often worn when an injury occurred.

By C. G. McLachlan

INTRODUCTION The work described in the following paper was under-taken with a view to determining, if possible, the relative importance of some of the phenomena on which flotation seems to depend, in the hope that, if this information could be obtained, it would be of value in dealing with the problem as a whole. At the outset, brief reference will be made to three papers which had a considerable bearing on the course followed in the present investigation. In 1919, Langmuir, in a paper on 'The Mechanism of the Surface Phenomena of Flotation', showed that mono-molecular films of very great stability could be produced on solid surfaces with oleic acid, but that pure paraffin oil, though spreading readily on a dean dry surface, was easily displaced by water.

Jan 1, 1926

By T. J. Lynch

A new class of polymeric dispersants for industrial minerals has been synthesized and evaluated. Currently available dispersants give initial low viscosities at high mineral loadings, however slurry viscosities can rapidly double or triple on standing over the first several days. The new dispersants give low initial viscosities that are more stable and maintain a lower viscosity for at least one month. The new dispersants are made possible by controlling the polymer molecular weight distributions during their manufacture such that essentially all of the dispersant is adsorbed onto the mineral surface, preventing depletion flocculation.

Jan 1, 2012

By Steve Kral

The Prospectors and Developers Association of Canada (PDAC) was established in 1932 in response to proposed regulations that would have threatened prospectors in Ontario. From there, the association grew to represent the interests of Canada?s mineral exploration and development industry. The PDAC?s mission statement reads: ?The PDAC exists to protect and promote the interests of the Canadian mineral exploration sector and to ensure a robust mining industry in Canada. The PDAC will encourage the highest standards of technical, environment, safety and social practices in Canada and internationally. ?Today, the PDAC?s 6,000 individual members include prospectors, developers, geoscientists, consultants, mining executives and students. In addition, the association?s membership includes 950 corporate members, representing senior, mid-sized and junior mining companies in addition to organizations that provide services and equipment to the mining industry. In 2010, the PDAC adopted its e3 Plus principles, a framework to guide its membership in responsible exploration.

Jan 1, 2011

By Gieskieng, D. H.

Published tables of jaw crusher capacities are compiled for the most part from field performance data, interspersed with interpolations, extrapolations, various safety factors, and other modifications. Such a table attempts to balance and equalize field data from widely different materials, with differences of crushability, efficiency of feeding, sizing of the feed, and so on. The tests described in this paper were undertaken with the objectives of checking previously reported capacities; of studying the effects of various factors upon the capacity, including jaw plate curvature; and, if possible, of deriving a general capacity equation. Such an equation has been derived from the data obtained in these tests. It is given together with factors for its use. While more accuracy than is usually required may be obtained by careful application of the equation, it is of simple form and provides a convenient reference plane upon which the potential capacity of various crushers may be compared, and with which operating adjustments may be made on existing installations. The principal deviation in these tests from the usual approach consists of a laboratory technique which has been developed for the production of selected

Jan 1, 1949

By Richard H. Bares

This report describes the purpose and application of seventeen statistical and mathematical procedures used in a series of studies made in the project ?A Systems Approach to the Reclamation of Strip-Mined Areas in North Dakota". The objective is to help readers better understand the utility of these procedures.

Jan 1, 1982

By Olgac Kangal, Ali Guney, Gulay Bulut, Guven Onal, Ayhan A. Sirkeci

This paper presents the results of pilot scale column flotation applications in the two different copper concentrators in Turkey. The Kure Copper Plant is located in the Black Sea Region of Turkey. In Kure, a very fine grinding requirement for an adequate level of liberation makes a successful flotation difficult and consequently the final concentrate can hardly assay above 16% Cu Column flotation tests were conducted at the plant site using two different column types The experiments proved that the grade of the concentrate could be increased from about 14% Cu to 25-26% Cu. Murgul Cakmakkaya Copper Concentrator is the largest copper concentrator in Turkey. Although concentrate production capacity is around 170,000 tons annually with 22-23% Cu content, this figure tends to be much lower than that. In Murgul a Turbo Column of Multotec Company of South Africa was employed. As a result of systematic column flotation tests, the grade of the concentrate was increased from 20.3% Cu to 28.7% Cu.

Jan 1, 2003

By Bauduin C. Besix

The Eurocode 7 "Geotechnical Design" is based on "Limit State Design", tackling the uncertainties as much as possible at their source through: - selection of characteristic values of variables (loads, soil properties, pile resistance,...); - partial factors applied on the characteristic values; - model factors to account explicitly for uncertainties of the calculation rule if necessary. Eurocode 7 will propose three "design approaches". The selection of one of them will be by National Determination. For pile design, the approaches are: - approach 1 is a "material factoring approach" at load side and a "resistance factoring approach" at resistance side. The structural and geotechnical design are checked for both of two separate sets of partial factors. - approach 2 is a "load and resistance factoring approach" and is in several aspects close to a deterministic approach. The design is checked for one set of partial factors. - approach 3 is a material factoring approach, at load as well as at resistance side. The design is checked for one set of factors. The aim of this paper is to introduce to the design of pile foundations based on pile load tests and on ground test results (semi-empirical and analytical methods) in the frame-work of the three design approaches. Detailed attention is devoted to: - the selection of the characteristic value of the pile resistance, accounting for spatial variability and stiffness of the structure; - the reliability of the prediction of the pile resistance using analytical or semi-empirical methods which may be accounted for through a "model factor". The results of a large test campaign on screw piles in OC Clay and a calculation example illustrate the proposed procedure when calculation rules using CPT results are used.

Jan 1, 2002

By Randy R. Huberty

Although originally designed with deep foundations consisting of all driven steel H piles and drilled caissons, a unique application of Augered Cast-in-Place (ACIP) piles as an alternate design resulted in a significant cost savings for the Midfield Terminal Project at the Pittsburgh International Airport. The project was enormous in scope covering an area two miles long by one mile wide, with changes in elevation of over 200 ft. The varying geology combined with the large amounts of fill required resulted in a complex set of geotechnical design parameters that had to be evaluated through both load testing and analyses. A total of almost 400,000 lineal feet of ACIP piles were installed for this project.

Jan 1, 2001

Coal Preparation Research at Turkish Coal Enterprises (TKI)

Sep 13, 2010

By C. Edward Chamberlain

A Bureau of Mines procedure was developed for the analysis of volatile matter in airborne coal dust-rock dust mixtures prior to, and resulting from, coal mine fires and explosions. Dust in the 10-to 20-mg weight range can be analyzed. Volatile matter is determined by a greatly scaled-down version of the empirical macro-scale method used by the Bureau. The alkaline earth carbonates in the rock dust are dissolved in acid prior to the volatile matter determination of the residue, and the rock dust content is calculated from the analysis of calcium and magnesium by atomic absorption.

Jan 1, 1974

By G. R. Moulder

A device was developed that measures dynamic stress (ultrasonic energy) transfer through installed rock bolts, a measure that is directly proportional to the degree of grout bonding of the bolt to the mine roof structure and thus the ability of the bolt to bear static stress. The rock bolt bond tester (RBBT) is a hand-held portable device that shows three ranges of bolt bond condition; i.e., one-third (Bad bond), two-thirds (marginal), or fully bonded. These are shown respectively by a red, yellow, or green light that displays for 4 s. RBBT performance was verified with 2 1/2-to 8-ft bolts installed in various types 0f mine roof structures (sands tone, shale, and boney coal-mud), and 15 now being tested by the Bureau of Mines in mines across the United States. The unit is about the size of a five-battery flashlight and contains the transducer electronics, and battery pack. The RBBT is designed for extreme ease of operation, requiring only manual contact with the bolt and signal read-out. The batteries are rechargeable and the package is designed for durability in a mine environment.

Jan 1, 1983

By N. Kumar Kittusamy

ALTHOUGH MANYSTUDIES HAVE SHOWN an association between operating heavy construction equipment and symptoms of musculoskeletal disorders (MSDs), little research has been performed that systematically characterizes the exposure of operating engineers to ergonomic hazards. This study evaluated: 1) vibration at the seat/operator interface;2) transmissibility of vibration in the Z-axis; 3) psychophysical ratings of vibration level and vibration discomfort; and 4) postural requirements of the job. Results indicate that the digging operation had higher levels of total weighted acceleration than high- or low-idling conditions. Transmissibility data showed that the seat amplified vibration, particularly in the lower frequencies. Seats demonstrated that they may not be sufficient in protecting operators from long-term effects of vibration exposure. High positive correlation was found among subjective ratings (vibration discomfort and vibration level), but moderate positive correlation was found between subjective ratings and quantitative vibration levels. Postural evaluations revealed that the operators were required to assume awkward postures of the neck, shoulder and trunk while performing their jobs. Work-related injuries and illnesses pose a continuing threat to the health and well-being of American workers. The construction industry has been historically recognized as having higher rates of fatality, injury and illness than other industries (McVittie285+; BLS). In 1994, an estimated 218,800 lost-work-day injuries were reported in the construction industry (BLS). Construction also had the second-highest incidence rate for sprains and strains. Although the industry has made progress since then, injuries and illnesses, including MSDs, continue to because for concern.

By Walter B. Hester

All persons and communities that have experienced strong-motion earthquakes are convinced of the importance and complexity of earthquake problems thatmust be solved in order to reduce the personal hazards and property losses to a reasonable minimum. It is also clear that absolute elimination of all risks is impossible. Reduction of existing hazards and precautionary measures which will minimize chances for disaster can be accomplished by realistic appraisal of the effects of recent earth- quakes on modern structures and installations. Localities that have reason to expect so-called strong- motion earthquakes can anticipate these effects by taking appropriate steps. Valid earthquake information can only be obtained from earthquakes. Each earthquake contributes to the body of knowledge by additional facts and by clarification of previous observations. Rational interpretation of the data followed by practical application of the conclusions can contribute greatly to the safety of persons and property. The general public expects the architectural and engineering profession to accept this obligation and render this service. Most earthquake hazards are man-made and arise from the imperfections of the works of man and his failure to anticipate the consequences when the natural characteristics of his environment are ignored. If it is not given to man to prevent such natural phenomena as earthquakes, it is sometimes within his power to control their destructive effects and to reduce to a minimum the toll of life and human suffering.

Jan 1, 1958

By Sandin E. Phillipson

The Mine Safety and Health Administration?s Roof Control Division responded to a massive ground failure at an underground marble mine in northern Georgia. The ground failure occurred in a benched area that had been abandoned in the early 1990s. It involved the failure of an estimated 19 pillars, in conjunction with a massive roof fall of an undetermined extent that was at least 60 ft high. Pillars in the benched area had been mined nominally 40 x 40 feet to a height of 50 feet ft, with 40-ft mining widths, although it seems likely from measurements and accounts from mining personnel that pillars were even smaller than intended. Average overburden depth was 500 ft, and the rock mass was characterized by three sets of intersecting geological discontinuities that not only defined very blocky conditions that were conducive to pillar spalling and volume loss, but they were also adversely oriented in such a way as to cut diagonally through pillars at a high angle. The recently released S-Pillar software from NIOSH was used to determine pillar safety factors in the failure area and indicated that pillars were undersized for the conditions. S-Pillar was used to assess pillar stability in active areas to evaluate the likelihood of experiencing similar collapses in the future. S-Pillar correctly identified the pillars in the bench area as having been at risk for instability, in light of their ultimate failure. A two-dimensional finite element model was used to evaluate the possible stages of failure and to assess the likelihood of continued failure in the benched area that might affect more distal mine openings. Although stone mines are generally characterized as having more forgiving conditions than those found in softer sedimentary rocks, the failure shares some characteristics with domino-style massive pillar collapses experienced in coal and trona mines. First, the minimum dimension of the benched area approached 350 ft; second, the pillars defined by benching had small width-to-height ratios (0.8), and; third, the pillar failure area was slightly greater than 4 acres. The massive pillar collapse and associated roof fall illustrate the importance of incorporating pillars that have been properly sized for depth and for the final bench height. Furthermore, the designed dimensions must be adhered to during the actual mining process. Finally, the importance of understanding the geological conditions and their effect on the rock mass is critical.

Jan 1, 2012

By W. R. Hibbard

Evidence is presented which confirms previous findings that models of solution strengthening depending solely on lattice parameter changes are incomplete. Direct evidence for the Suzuki interaction of chemical effects was obtained from alloys with constant lattice parameter, for which solution strengthening was nearly independent of temperature from 300° to 20°K. SOLUTION hardening principles have been reviewed recently by Parker and Hazlett.' In addition, the interactions of dislocations and solute atoms were reviewed by Cottrell.' It is not proposed to review this information again here, but to refer only to those details which are pertinent to the developments which have occurred since these papers were published. Literature Survey To set the stage, it has been known for some time that solid solutions are stronger than the pure parent metals, and that the strength increases with increasing amounts of alloying element. One of the most extensive earlier investigations was that of Lacy and Gensamer,3 who reported that the solid solution strengthening of iron is a power function of the composition, that the relative strengthening is a function of the solubility limit, and that the rate of strain hardening is a function of the amount of solution hardening. Thus, the slope of the plastic portion of the stress-strain curve increases with increasing yield strength. An approach to the development of principles resulted from work by Gulyeav,4 who reported that the strengthening effect of solid solution alloys is periodic in character when plotted as a function of the atomic number of the solute. A more quantitative approach was to relate the amount of solution hardening to the lattice parameter of a solid solution. This was done quite early by Norbury,5 and later by Brick, Martin, and Angier,6 Frye and Hume-Rothery,7 and French and Hibbard. This relationship is only approximate in character. The next development was to relate the amount of solution hardening to lattice stress, as proposed by Frye and co-workers.9 They calculated what they called ionic overlap from the lattice parameter changes represented as a change in volume, using Bridgman's hydrostatic compression equation. The resulting correlation was somewhat improved as compared to the simple correlation with lattice parameter. The next step was carried out by Dorn, Pietrow-sky, and Tietz,10 who suggested an effect of valence differences in addition to the effect of lattice parameter. Their proposed parameter shows flow stress as a single valued function of the concentration and a relationship involving these two atomic variables. In addition, they contributed new data on the temperature dependence of solution hardening which indicated that it was a strong function of temperature for aluminum alloys. Allen, Schofield, and Tate11 carried the valency effect even further by reporting data indicating that with a given solvent element the stress-strain curve is a function of electron density, entirely neglecting the size factor, which varied by a factor of two. This evidence led to a quantum mechanical calculation by Cottrell, Hunter, and Nabarro,12 based on the formation of a dipole around an edge disloca-

Jan 1, 1959

By C. Arthur Lefler

The hydrometallurgical processes for recovery of gold and silver in use at Round Mountain, Nevada and the practical aspects of the operation are discussed. Included are heap leaching by cyanidation, upgrading of solutions by adsorption of values on activated carbon and desorption (stripping) for electrowinning and subsequent refining steps to produce dore metal.

Jan 1, 1981

By P. Kluge

Mining engineers frequently encounter complex design problems for which the critical components of the design are difficult to quantify or compare. Teams of people typically work on these designs and human perceptions and judgments play a strong role. To assist with this process, the analytical hierarchical process (AHP) as a decisionmaking tool is described in this paper. Although the technique is used in many other disciplines, it is currently not widely used in mining engineering in South Africa. To use the AHP process, the problem should be treated as a hierarchy that defines the goal, the alternatives to reach it, and the criteria for evaluation of these alternatives. Pair wise comparisons are conducted on the criteria of the hierarchy to establish priorities. The value of the technique is that it is simple to test for consistency amongst the pair wise comparisons to ensure that the answer obtained is better than that provided by a random selection. To illustrate the technique, the use of a backfill support system in a platinum mining project was investigated. Ten design parameters, which will be impacted by the use of backfill, were identified and weighted according to their relative importance. The result of the AHP evaluation was that the use of a backfill support system should be preferred to a conventional support system at the mine.

Jan 1, 2011

By Simon D. Handelsman

?Artisanalmining ?Application of human energy (e.g. pick & shovel) directly to produce minerals ?majority no technical skills and lack adequate working tools ?Small-scale mining ?Application of modern technology for limited scale mineral production Significance of ArtisanalMining ?15 million people in artisanaland small scale gold mining ?55 developing countries ?Use of mercury damages health of 100 million people

May 1, 2006