Search Documents

By A. F. Colombo

Bench-scale research was undertaken to determine if adding ammonia to cyanide leaching solutions would enhance the extraction of copper from an argillaceous Michigan copper ore. Two leaching techniques, (1) rolling using a tumbling bottle and (2) aerating using a modified Buchner funnel, and variations in pulp temperature; were employed in evaluating the effect of ammonia concentration on copper extraction. Under these experimental conditions, the extraction of copper was shown to be independent of ammonia concentration and entirely dependent on cyanide concentration.

Jan 1, 1968

By Braden T. Lusk, Rex A. Meyr, Kyle A. Perry

Following three major mining accidents in 2006, the MINER Act of 2006 was enacted by MSHA and required every underground coal mine to install refuge alternatives to help prevent future fatalities of trapped miners in the event of a disaster. A polycarbonate safe haven wall for use in underground coal mines was designed and modeled using finite element modeling in ANSYS Explicit Dynamics to withstand the MSHA required 15 psi (103.4 kPa) blast loading spanning 200 milliseconds. The successful design was constructed in both half-scale and small scales in the University of Kentucky Explosives Research Team’s (UKERT) explosives driven shock tube. The constructed polycarbonate walls were tested multiple times to determine the walls resistance to blast pressure. The results for each test were analyzed and averaged to create one pressure versus time waveform which was then imported into the finite element program and modeled to compare deflections of each part to that was measured during testing for model validation. This paper summarizes the results.

Jan 1, 2014

By Charles W. Daugherty

INTRODUCTION The Washington Metropolitan Area Transit Authority's (WMATA's) rapid transit system, Metro, ultimately will comprise 162.5 km (101 miles) of line divided among 10 routes. As shown in Figure 1, about 24 km (15 miles) of the system will consist of mined rock tunnels distributed along the A, B, C and K Routes. The structural construction contracts for all of the A, C and K Route rock tunnels are complete and trains are running in about one-third of them. A contract for construction of rock tunnel section B-9, the southernmost third of the B Route, was awarded on June 27, 1980. The final design of Sections B-10 and B-lla, the remainder of the rock tunnel portions of the B Route and the Metro system, are well advanced and should be under con¬struction by 1982. Of Metro's 87 stations, 11 will have been constructed by mining in solid rock, a not inconsiderable achievement, since each structure must be over 183 m (600 feet) long, wide enough to accommodate two trains and one or two passenger platforms, and high enough to achieve a stable arching action without encumbering columns. With the passage of years, some original priorities have been reordered, and ways have been sought to streamline and simplify this most complex of Metro structures without grossly violating the architectural standards that make it unique. This paper will summarize that search, and describe the design and construction aspects of the resulting product, the dual chamber rock tunnel station.

Jan 1, 1981

By David C. Oyler

The U.S. Bureau of Mines studied the interaction of longwall shield supports and adjacent strata at the Meigs No. 31 Mine in southeastern Ohio. Twenty-three legs of twenty shields at midface were instrumented with pressure transducers and monitored for 11 weeks. During the project, leg setting pressures were reduced twice to determine the effect of setting pressure on shield-strata interaction. No correlation was observed between setting pressure and leg loading rates. The shield loading profiles were consistent with a model in which the roof consists of two zones, a thin immediate roof loading the shields well below the typical setting force and a main roof zone essentially supported by the coal and gob and loading shields through its convergence. This model was used to develop an equation for estimating average loading rates at the site. The only variable of the equation is time, and the equation consists of an exponential term to account for the immediate roof loading and a linear term to account for main roof loading. The equation gave good correlation with average loading rates, but the variation in loading from cycle to cycle was too great for the equation to give good predictions of individual cycle loading rates.

Jan 1, 2010

By Brian Ulrich

The majority of individuals involved in the mining industry can appreciate and under-stand that mining is an activity that is necessary to satisfy the very basic needs of society, and to assist in accommodating our ever-changing world. As the expression goes, ?if it can?t be grown, it has to be mined.? And at this point in time, society has granted the mining industry the right to go about the business of mining, with the general anticipation that the work will be carried out without causing undue harm to the environment or populations in and around the mining operation. The term ?sustainable development? is gaining momentum as a popular concept, and indeed it has become something of a catch-all phrase, but it is important that the idea behind the term is not cast aside as a nonsense buzz word, as it simply is an indication that development (e.g. mining) can be satisfactorily carried out with an eye toward stewardship of the environment and society. On Feb. 19, 2010, a round-table discussion (Roundtable 2010) on ?Strides Toward Sustainability in Mining? was hosted by Knight Piésold and Co. (Knight Piésold) at the Red Lion Inn and Casino in Elko, NV. Knight Piésold had local representatives (Bryan Ulrich and Steve Boyce), as well as representatives from other office locations (Cynthia Parnow and Rick Damiani from Denver, CO, and Rick Frechette from Tucson, AZ) to help facilitate the discussion. The meeting played host to 30 attendees from five states. Attendees included personnel from nine mining properties and various corporate offices. The majority of participants were people who are directly involved with environmental work on a day-to-day basis. Others were project managers whose jobs involve some level of environmental focus.

Jan 1, 2010

By T. P. Weldum, W. Conger

"These studies address the relationship between mill media sizing and its grinding efficiency. Starting with the results from a review of the literature, the issues of initial media sizing for a new ball milling circuit, and then optimal media sizing for an existing milling operation, were studied. The Functional Performance parameters “Mill Grinding Efficiency” and cumulative “Mill Grinding Rates” from both plant and test-scale equipment were used, and provide valuable new insight into this topic. A plant media sizing diagnostic tool is presented, as are newly developed testing equipment and evaluation methods, and recent case studies.REVIEW OF MEDIA SIZING LITERATURE For a plant metallurgist to answer the question “How can I maximize plant profit by manipulating this grinding circuit variable?” she must know what effect the variable has on grinding circuit efficiency. Despite the significant cost of grinding media and its potential effect on production capacity, the ‘best’ media sizing remains ill-defined for any given ball mill circuit in the industry today. The underlying reasons for this will be discussed. But the importance of this issue drove Metcom and its industrial partners to take on the challenge of how to engineer the ball charge for an existing grinding circuit. In the absence of any proven method, the first step was a review of the literature. Sponsored by Cleveland-Cliffs, Inc., a broad review of the literature was undertaken, producing “The Effect of Media Sizing on Ball Milling Efficiency” (McIvor, 1997). Among hundreds of publications that were reviewed that discuss the topics of media sizing or wear, forty-five were studied in detail. These were grouped into: plant experiences; laboratory and pilot plant investigations; media wear studies; population balance modeling studies; and general papers on ball milling which included the topic of media sizing. The reader is encouraged to refer to that review. The findings remain unchanged, although some relevant papers have been written since (e.g. Staples et al, 1997; Banasi et al, 1999; Orford et al, 2006; LaMarsh, 2015). The main findings of the review were as follows:"

Jan 1, 2018

By Jon G. Bredeson

The electromagnetic noise that exists in a mining environment is quite severe and was shown to have been reasonably well documented by a number of researchers in the Phase I Report. The noise levels are such that prudent communication design requires the careful use of all the electromagnetic noise data available. A comprehensive survey was undertaken to determine techniques used in various industrial environments to achieve secure communications in the presence of electromagnetic interference. The techniques were given in the Phase I Report and are rudimentary, but have produced reasonably good results. A number of these techniques could be applied to the mining environment.

Jan 1, 1980

By André Piché

"Over the last ten years, several developments have been undertaken to conceive a machine capable of carrying out simultaneously all the mining tasks in hard rock deposits: cutting, mucking, hauling, ground support and dust control.The main advantages of continuous mining over conventional drill and blast is the elimination of the cyclical nature of the actual methods. Other advantages sought are improved stability of mine openings, higher productivity, lower costs, and a cleaner and safer mining environment. Noranda has con-tributed to these developments in a major way. As a member of HDRK, Noranda participated in the development of two mechanical continuous mining machines; the TM60 and the Wirth. Noranda also undertook a development of its own based on the utilization of electricity to break rock. This technology is called plasma blasting (PBT). The concept of plasma blasting is illustrated in Figure 1.When the operating voltage is reached (18kV), the energy is released through a high current switch (500k A) into a coaxial powercable. It is then delivered to the tip of an electrode inserted into a drill hole which is filled with an electrolyte (water). When the energy reaches the electrolyte, it is instantaneously transformed into a high temperature, high pres-sure plasma that produces a shock wave capable of breaking rock(1).After initial testing of the plasma blasting technology in the lab and in the feld, two experimental platforms were constructed. The first one, a test bench, was erected at the Noranda Technology Centre in Pointe Claire, Quebec.(2)The second one is a rock breaker prototype based on a standard diesel-powered carrier (Fig. 2). Each platform was equipped with a 300 kJ pulsed-power module.In 1993, the rock breaker prototype was used for an extensive series of tests in the field. During that campaign, over 700 oversized boulders were blasted. The results of the tests demonstrated that more durable components for PBT were needed. The test bench was then used to successfully develop and test long-lasting components (probe, switch, cable, connector) that can be adapted to industrial platforms leading to the commercialization of the technology."

Jan 1, 1996

By J. M. Goris

The U.S. Bureau of Mines is conducting research on cable bolt ground supports to assess their material and support properties, to provide design criteria for using cable bolt supports as roof control systems under various types of underground mining conditions, and to provide a mathematical model of cable bolt support systems. Part 1 describes laboratory studies of the support properties of cable bolts made of conventional steel cables and provides recommendations on such topics as the use of thick grouts, selection of breather tubes, and reduction of water bleeding in cement-based grouts. The studies evaluated both single and double cables; effects of different embedment lengths, water-cement ratios, and grout curing temperatures on support strength; effects of use or nonuse of breather tubes; pumpability and water-bleeding properties of grouts; and the strength properties of sand-cement grouts. Part 2 will cover the strength characteristics of birdcage cable bolt supports, epoxy-coated cables, and cables with steel buttons attached.

Jan 1, 1990

By Thomas Gregor, Brian Garrod

As the popularity of precast concrete segmental linings for tunnels is growing in North America, some problems related to grouting of, and near, these linings are starting to appear. The installation of a segmental lining behind a TBM requires that the annular space around the lining be quickly filled with grout to prevent collapse of the ground. In practice, the filling of the annulus is frequently delayed and takes place a distance behind the machine typically via grout ports centrally located in the segments. If partial collapse of the annulus has occurred, it may become necessary to use higher grouting pressures in an attempt to distribute the grout. There have been several occasions where these increased pressures have caused damage to the tunnel linings. Similarly, compaction grouting adjacent to a tunnel lining can cause damage. This paper quantifies the effects of such grouting on a typical precast lining.

Jan 1, 2005

By Charles J. Zablocki, Robert J. Kamilli

"Abstract - Buried, possibly mineralized granite cupolas at the Silsilah tin deposit in Saudi Arabia (lat. 26°06' N, long. 42°40' E) have been successfully located using a closely spaced electric-field-ratio profiling technique. In this study, electrical fields at 27 and 270 Hz across grounded electrodes spaced 50 m apart were measured along six traverses. This method is interpretable by inspection, unlike the dipole-dipole technique, which requires mathematical modeling for interpretation.In the study area, the technique allowed the authors to identify and distinguish among unroofed granite cupolas, cupolas with their aplite-pegmatite apical contact zones intact, strong (quartz-rich) and weak (relatively quartz-poor) greisens, dikes, faults, and pervasively argillized rocks.This method should be useful in the valuation of other shallow mineral prospects in similar settings in other parts of the world, especially deposits for which the location of vertical contrasts is important, such as veins or mineralized zones associated with the apexes of small igneous cupolas."

Jan 1, 1993

By David E. Fogelson

One model each of three different makes of portable displacement seismographs was calibrated on a shaking table capable of 5,000 pounds of force, Calibration tests were conducted in the frequency range of 5 to 200 c.p,s, and in the amplitude range of 0,002 to 0.05 inch peak-to-peak, The seismographs were tested under two mounting conditions: (1) The feet of the instrument were bolted to the shaking table, and (2) the feet were resting on emery cloth affixed to the table, The results of these tests show that, in the frequency range of 5 to 40 c.p,s, and for vibration levels less than 0.2 g, the magnification for all three instruments is constant with input level but varies slightly with frequency. For vibration levels greater than 0.4 g. and for frequencies greater than 40 c.p.s., the magnification of all three instruments shows large variations with frequency and amplitude of table motion.

Jan 1, 1962

By Donald W. Mitchell

Studies were made in the Bureau of Mines Experimental coal mine to evaluate the effectiveness of a few extinguishing agents and techniques for controlling a fire on a simulated mining machine. The investigation showed that water containing an alkali-metal salt or a surface-active (wetting) agent was more effective than water alone. For close attack, fog applications was the most effective technique studied; high rates of agent application controlled the fire more quickly than low rates. The ability to control the fire increased as the distance of attack decreased. Dry powders controlled the fire when applied by shovel but not when applied airborne by rock-dust distributor or by hand fire extinguishers. Dry alkali-metal salt powders (potassium and sodium bicarbonates and sodium tetraborate) quenched the fire more readily than limestone dust. In each instance the finer powder, the greater its effectiveness. In an open ventilated entry, smoke and hot gases backed against the air currents. An airspeed of 230 feet per minute was required to permit approach to within 10 feet of the fire. At lower airspeeds, approach could be made by extending the brattice across the bottom two-thirds of the entry, by pushing the smoke ahead with water sprays, or by discharging dust from a rock-dust distributor. In a dead-end entry, the fire was approached to within 30 feet by coursing fresh air along an airtight line brattice; however, it was safer, easier, and less time-consuming to attack the fire from a fresh-air base 100 feet away with a solid stream or by high-expansion foam; the latter method was more effective.

Jan 1, 1961

By Ralph Husack

The Bureau of Mines investigated the effect of gamma radiation on reactions between Pennsylvania anthracite and fluorine and chlorine. In the tests with fluorine about 90 percent of the coal reacted at 350° C to form volatile products whether or not irradiation was employed. Up to 0.8 ml of liquid products per gram of anthracite was collected. Among the 25 com-pounds indicated by gas chromatography, fluoroform and l,l-difluoroethylene were tentatively identified from their relative retention times and perfluoro-cyclopentane from its infrared spectrum. In addition, a clear, hard, wax, probably a fluorocarbon, was formed at 45° C in both the presence and absence of radiation. With chlorine there was no significant difference due to radiation, and preliminary tests indicated that the chlorine reacted more with the organic matter of anthracite at 200° C than with inorganic matter. At 400° C the results were inconclusive because of excessive corrosion in the reaction vessel.

Jan 1, 1966

By K. E. Robinson

This study provides an initial indication that mill tailings produced in the Coeur d'Alene Mining District of Idaho can be placed on floodplain areas in a technically acceptable manner without artificial liners and without seriously contaminating the surrounding area. Tests have shown that landfills on these unused areas can result in returning these areas to productive use. The engineering properties of mill tailings permit construction of stable embankments. Designed slope protection inhibits water erosion. Among the environmental considerations in using tailings for landfill construction are the acid and other contamination produced by tailings and wind erosion of exposed tailings surfaces. The initial results indicate that adverse impacts are not as severe as previously thought, and mitigative measures are feasible. Based on the preliminary data, and in accord with existing Federal and State waste management regulations, a conceptual design has been developed for 23 potential landfill sites in the District, which could reclaim 750 acres of floodplain. A cost analysis of landfill construction with mill tailings indicates that the method would be an economically viable means for increasing the valleywide tailings storage capacity, provided construction with slurried tailings is feasible. A Stage H study is proposed to evaluate slurried tailings as a foundation material, as opposed to hauled tailings used in this present study.

Jan 1, 1981

By Tianzu Yang, Weifeng Liu, Lin Chen, BOYI XIE, DUCHAO ZHANG, HUI XIAO

In this study, the oxygen-rich bath smelting process of copper dross was simulated using Factsage software. It was found that the two-step simulation results agreed better with the industrial data, especially in the speiss. Bismuth (Bi), lead (Pb), antimony (Sb), arsenic (As) and copper (Cu) contents in the speiss by two-step simulation differed from the industrial data by 0.6, 0.8, 2.6, 7.2 and 8.6 weight percent, respectively. The two-step simulation results indicate that the speiss partitioning of Sb, As and Cu increased from 60.1, 32.3 and 27.5 percent to 81.6, 67.8 and 47.2 percent, respectively, with the smelting temperature increasing from 1,050 to 1,250 °C, while the metal partitioning of Sb and Cu increased from 0 and 2.7 percent to 15.2 and 13.3 percent, respectively, with the separation temperature increasing from 400 to 700 °C.

By A. Kontopoulos

Refractory sulfide gold ores or concentrates require an oxidation pretreatment step to yield the contained gold amenable to the subsequent leaching step. The process options for oxidation pretreatment can be broadly classified as follows: roasting, high or low pressure oxidation bacterial oxidation, chemical oxidation, each with a number of alternative suboptions. Roasting and high pressure oxidation are being applied on an industrial scale; the stage of development of the other options range from preliminary laboratory to advanced pilot plant- In this paper, the major technical, environmental and economic aspects of the above processes are being discussed. Future industrial trends will also be considered. Particular emphasis will be placed on the treatment of arsenical ores and concentrates, where safe plant operation as well as, handling and disposal of the arsenic containing products and/or effluents 'and residues is of paramount importance.

Jan 1, 1990

By Adeyemi Adesina, Subhabrata Mishra, Syed Mohammed Mustakim, Malaya Kumar Jena, Shaswat Kumar Das

Utilization of low-grade manganese ore adopting the carbothermic reduction roasting process is a proven method to produce high-grade manganese ore. To minimize industrial waste and protect the environment, gas cleaning plant sludge (GCPS), which is a solid waste from steel industries, was employed as a reductant to perform the reduction roasting process. The optimum conditions to carry out reduction roasting of the low-grade manganese ore were found to be: a roasting temperature of 950 °C, a residence time of 2 h, 40% GCPS as reductant, and magnetic separation at 5000 G for a manganese ore size of –10 mm. A lowgrade manganese ore comprising Mn grade 31.27% and Fe grade 19.78% having a Mn/Fe ratio of 1.58 containing a high silica content of 26.48% was used for the carbothermic reduction roasting having mineral phases of pyrolusite (MnO2) and hematite (Fe2O3) as found from XRD. The gangue minerals were separated during the magnetic separation, and the upgraded product was obtained, which reached a maximum value of TMn 49.5% with RMn 76.55% and TFe 62.19% with RFe 42.51%. In the study, activated charcoal (AC) was also taken as a reductant for comparative analysis; the experimental results revealed that GPCS performed better than that of the AC, showing potential to be used as a reductant in metallurgical industries. However, the resultedMn/Fe ratio was very low for the reduced sample; therefore, it can be used for smelting along with high-grade manganese ores as a feed.

Mar 5, 2021

By Ibil S

The Gameta Gold Deposit is located on the north-eastern corner of Fergusson Island in the D'Entrecasteaux Islands of Milne Bay Province, PNG, at lat. 9¦ 25' 5, long. 150¦ 47' E or AMG co- ordinate 256740 E/8959000 N (Figure 1). The area is covered by the Fergusson (SC56-05) 1:250,000 scale Topographic Map Sheet and the Koitabu (9079)1:100,000 scale Topographic Map Sheet. The property is held 100% by Union Mining NL (UMG) and lies 105 km NNE of Alotau and 33 km to the ESE of UMGs recently developed Wapolu Gold Mine, a Joint Venture between UMO (51%) and Macmin NL (49%). The inferred resource estimated from surface results and 105 RC drill holes, currently stands at 1.89 million tonnes at 2.6 git gold (1.0 g/t Au cut-off) or 155,000 oz. Evaluation of the property is currently proceeding. To date 111 RC holes have been drilled for a total of 4611 m.

Jan 1, 1997

Jan 1, 2004