Search Documents

By D P. Blair

Rio Tinto’s Hope Downs Operations are currently mining iron ore in their South Central Pit. Prior to the commencement of mine operations, Hope Downs carried out an extensive archaeological investigation and identified an ancient rock shelter lying within the proposed mine boundaries. The site is significant to the traditional owners/custodians of the land in this part of the Pilbara, and thus the final pit design was changed to preserve the rock shelter, which now lies 30 m outside the mine boundary. In order to further preserve this ancient dwelling from blast-induced damage, blast design procedures were improved over time to minimise the vibration impact when blasting close to the shelter. Blasting and vibration monitoring commenced in May 2008 using pyrotechnic delay sequences and normal-direction firing. In October 2009 electronic delays were used to reverse-fire blasts close to the shelter in order to create a damage zone between the initiating holes and the rock shelter. A detailed statistical analysis of the vibration data shows a reduction in the higher levels of vibration for blasts fired after October 2009, which is most likely caused by the created damage zone. In May 2010, a site-specific vibration model was developed and implemented, and based on Monte Carlo waveform superposition. This model was used to give a further insight and improvement to the blast delay sequences when blasting close to the shelter. However, such models are expensive to implement and have limitations, which reduces their potential for estimating the probability of getting an excessive vibration due to a given blast design. In this regard, it is more realistic and significantly less expensive to use a recently developed probabilistic analysis based on simple charge weight scaling. This analysis shows that there was a higher probability of exceeding prescribed vibration limits at the rock shelter for blasts fired before October 2009 than there was for blasts fired after October 2009.

Nov 8, 2011

By J. Wong, M. G. Lipsett, L. K. Daneshmend

"Current trends of increased size, complexity, and automation of surface mining equipment necessitate more comprehensive and objective techniques for equipment comparison and selection. The field of reliability analysis provides tools to generate quantitative bases for maintenance and reliability aspects of such comparisons. Results from statistical analyses of failure and repair time data are used to perform the comparison. A case study is presented which analyzes five machines of two different technologies and three different designs.IntroductionThe surface mining industry is currently faced with a rapid evolution in production equipment. The more obvious trend in this evolution is the steady introduction of even larger machines. Parallel, and complementary, to this increase in size is the introduction or adaptation of new technologies. Together, these two trends result in new surface mining equipment designs; these designs are often more complex and may feature technologies that have yet to be proven for the application or at the scale they are now fielded.The prospect of significant automation of open pit equipment is also bound to add complexity to future equipment designs. Semi-automated features, such as drilling controllers (Aquila, 2000), have already been commercialized. Fully autonomous haul trucks have been demonstrated in open pit mines (Jackson and Zoschke, 2000). Design concepts for comprehensive teleoperation of open pit operations have been formulated (Lipsett, 1998).With this rapid availability and deployment of new technology and equipment, managers and maintainers are faced with a multitude of decisions regarding what equipment to acquire and what maintenance strategies to implement. In light of this evolution in mining equipment, it is necessary to develop better methods for making equipment management decisions (Dessureault et al., 1999; Paraszczak, 1999). The incentive for development of such techniques is that a large portion of an open pit mine’s operating cost is maintenance related, as shown in Table 1."

Jan 1, 2000

Project developent proceeds by increasingly detailed studies addressing overall project returns through an analysis of the substance, risks and costs associated with the following elements: ò Reserves ò Mining ò Processing ò Infrastructure ò Environmental Impact ò Product Market Computer-based expertise has a potential to ò Capture perishable expertise, making this available for shared access and so reducing the cost of human experience ò Consolidate know-how for optimising process operations, bringing consistency of judgement and advice to decision- making by making the rules, facts and preferences explicit ò Allow assignment of the basis and authority of decisions, so experts can pass routine expertise down the line, freeing their time to generate more. ò Force a review of expertise when creating the knowledge base.

Jan 1, 1989

By N. A. Abdel-Khalek

The amenability of carbonate separation from a sedimentary phosphate ore using a bioflotation process was studied. Two types of bacteria were chosen for this study. The experiments were performed using oleic acid as collector. The flotation experiments were carried out using statistical designs for optimizing the main operating parameters. A concentrate containing 0.78% MgO and 30.15% P2O5 with a recovery of 92.31% was obtained from a feed containing about 2.45% MgO and 27% P2O5. These specifications could not be obtained using conventional flotation experiments under similar conditions in the absence of bacteria. Measurements of zeta potential, adsorption of bacteria and collector, as well as froth power, were performed to explain the role of microorganisms in the surface modification of both dolomite and phosphate and in their interaction with the collector.

Jan 1, 2009

By S. Shrivastava, R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (KO88) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron- and steelmaking and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By H. Kinilakodi

In 2008, the authors developed a methodology for assessing underground coal mines for high risk for major-hazard events. It focused on major hazard-related violations of safety standards associated with high-risk conditions. Later using a sample of 103 mines with 2008 and 2009 data, injury measures and MSHA citation data were combined into a Safe Performance Index (SPI). The SPI was used to assess the relative safety-related risk of mines, including by mine-size category. In this paper, comparisons are made of SPI-associated, normalized safety performance measures across mine-size categories, with emphasis on small-mine safety performances as compared to large and medium-sized mines.

Jan 1, 2011

By K. M. Kim

A site-specific blasting model has been developed for the Asarco Mission mine. The main inputs to the model are the in-situ block size (F80), the post-blast fragmentation (P80) and the intact tensile strength (To). The output from the model is the specific blast energy (ESE). Modern techniques are being used to obtain the input parameters for the site-specific blast fragmentation model. In particular, image processing software is used to obtain both the in-situ block size and the post-blast fragmentation, and the Schmidt hammer is used to obtain the tensile strength at numerous locations throughout the rock mass. An initial model was developed using five test shots in one area of the mine that contains Argillite and is relatively homogeneous. This also included calibrating Schmidt hammer readings against actual Brazilian tensile measurements. The model for Argillite will be updated as more tests are conducted, and the model will be extended to the other four primary rock types at the Asarco Mission mine.

Jan 1, 2011

Assuming that a gold ore has been effectively ground to ensure maximum economic liberation of gold, the circuits that will have the most effect on the successful operation of a gold plant will be that of the leaching and carbon-in-pulp circuit (CIP). The reagent and utilities operating costs associated with leaching, adsorption, elution and regeneration would typically make up some 15% of total operating cost, whilst the capital costs associated with these areas is about 16% of the total. Although not largest (capital and operating costs associated with comminution are generally dominant) these items represent a significant proportion of capital and operating cost. Much more importantly, these plant areas represent the primary gold recovery process and their technical and operational efficiencies will have a significant impact on overall plant efficiency. The objective during process design of these sections is thus to develop a design which provides maximum technical and economic efficiency and which is robust to potential changes in ore throughput, mineralogical characteristics and head-grade. Experience has shown that, particularly for longer life and higher-grade projects typical of the South African underground gold mining industry, small changes in recovery and efficiency have a significant value over the life of the project.

Jan 1, 1999

By Forrest T. Moyer

The overall injury experience, excluding officeworkers, at metal mines and mills during the period 1961-63, reported by operators, was 174 fatal and 11,357 nonfatal disabling work injuries during an aggregate worktime of 451 million man-hours. These injuries occurred at a frequency rate of 25.55 per million man-hours, comprising 0.39 for the fatal and 25.17 for the nonfatal injuries. The combined severity rate of the disabilities was 3,779 days lost or charged per million man- hours, consisting of 2,314 for the fatal and 1,465 for the nonfatal injuries. The average severity of all disabilities during 1961-63, was 148 days per injury. The number of days lost and/or charged, ex- cluding officeworkers, at metal mines and mills during the period 1961-63, was 1,440,000 days charged to fatal injuries and 661,290 days lost from nonfatal injuries. An average of 70,966 men were at work daily. The outstanding cause for fatal injuries was the fall of rock or ore from the back, while most of the nonfatal injuries were caused by handling materials, slips or falls of persons, machinery, falls of rock or ore from back and side, and haulage. Injury experience at primary nonferrous smelters, refineries, and reduction plants during 1961-63, excluding officeworkers, was 23 fatal and 3,214 nonfatal disabling injuries during a total work- time of 277 million man-hours. The injuries occurred at frequency rates of 0.08 per million man-hours for the fatalities and 11.61 for the nonfatal disabilities. The severity rate for all injuries of 1,085 days lost or charged per million man-hours comprised 498 for fatal and 587 for nonfatal injuries. The number of days lost, excluding officeworkers, at primary nonferrous smelters, refineries, and reduction plants during 1961-63 was 138,000 from fatal injuries and 162,385 from nonfatal injuries, An average of 34,938 men were at work daily an active plant days during the three year period. The injury experience for officeworkers at metal mines and mills during the period 1961-63 was 20 nonfatal disabling work injuries, (there were no fatal injuries reported), during an aggregate work-time of 28,694,244 man-hours. These injuries occurred at a frequency rate of 0.70 per million man-hours. There were no fatal injuries reported for officeworkers at non-ferrous smelters, refineries, and reduction plants during 1961-63, but seven nonfatal injuries were reported during an aggregate work-time of 30,814,772 man-hours. The frequency rate for these injuries was 0.23 per million man-hours for this period.

Jan 1, 1967

By J. B. Goddard

Abstract. Leaching of, uranium in situ from sandstone deposits with ammonium carbonate solution containing: dissolved oxygen occurs rapidly compared with the leaching of the bulk of the sulfur present as FeS2. However because of their high reducing, capacity and their relative abundance, the FeS2 minerals consume; the bulk of the oxidants A pressure leach apparatus was-construtted which permitted the measurement of oxygen consumtion by FeS2. Oxygen consumption by FeS2 is best described by a first-order reaction. The experimental rate constants for various cores are roughly proportional to their FeS2 contents.

Jan 1, 1980

By Ryo Sasai, Takeshi Itakura, Haruki Imaizumi, Hideaki Itoh

"Emission of industrial wastewater containing harmful oxoanions is one of the serious problems on account of its toxicity and the environmental pollution, especially caused by boric, phosphinic, arsenic and antimonic species. In this study, we developed a novel treatment technique of such polluted-water by hydrothermal mineralization. The treatment is “Geomimetic” method for precipitating oxoanions in aqueous media as natural ore resources by using hydrothermal treatment with calcium salts mineralizer. The treatment made it possible not only to detoxify the polluted-water, but also to recover the calcium minerals such as Ca2B2O5·H2O, Ca5(AsO4)3(OH), etc. Concentration of each ion in treated-water was lower than that of effluent standard in Japan. Moreover, the residual concentration of each ion was independent of the initial concentration, but it depends only on the solubility of the formed mineral under hydrothermal condition. Therefore, the hydrothermal treatment could be recommended as one of the treatment techniques of polluted-water.IntroductionVarious oxoanions such as boron and arsenic oxo-anions have high toxicity against human health and the environment. They are important resources, however, for plating or advanced material manufacturing industries[1-3], from which the wastewater containing these oxoanions is generated every day. An appropriate treatment is often required for industrial wastewaters to attain national effluent standards of Japan (NESJ, B: 10 mg/dm3, As: 0.1 mg/dm3). On the other hand, there is no production of arsenic and boric resources in Japan, and they are expected to be recycled. Therefore, the establishment of a system for the removal and recycling of arsenic and boron from wastewaters is of global significance.Several methods to remove them from aqueous media have been already reported by using adsorption[4], electro-coagulation[5], membrane separation[6-8] and biological techniques[9]. However, these methods have the following problems because of their stability in water. (1) Removal yield is low, especially for tri-valent arsenite ion (AsIIIO3 3-) and borate ion. (2) The applicable concentration range is narrow. In addition, the used adsorbents or collected residues after treatments are sill hazardous wastes, so that they must be treated by a proper method. But, it is very difficult to convert them to recyclable resources at most industrial plants. These problems are caused by the difficulty to recover these oxoanions as stable solid precipitates with low solubility in water. The establishment of recycling system of these hazardous compounds will be one of the world-important issues, especially, in Japan, which is poor in natural resources. On the other hand, compounds that contain high arsenic concentrations and are insoluble in water, are often found in natural minerals, for example, as haidinglite (Ca(AsO3OH)·(H2O) or Johnbaumite (Ca5(AsO4)3(OH)). This fact suggests that nature has an ability to produce insoluble As-bearing minerals. Similar phenomena can be found in case of boron, antimony, etc."

Jan 1, 2008

By C Vejrazka

Northparkes is located 27 km north of the township of Parkes in central New South Wales, Australia. The operations consist of underground block cave mines and an ore processing plant that produces high-grade copper and gold concentrate. Production is currently sourced from the E48 Lift 1 block cave mine and open cut stockpiles. Mining commenced at Northparkes in 1994 as an open cut operation. Underground block cave mining began in 1997. Northparkes was the first mine in Australia to use the highly efficient block cave mining method, which relies on gravity and natural rock stresses to fragment the ore.The occurrence of air blasts is one of the principal mining hazards in block caving operations between the time of first undercutting and breakthrough of the cave to surface. As such, it needs to be managed continuously, and risk assessments need to be reviewed on a regular basis for applicability to changing conditions. Unfortunately, there is little literature on how to practically approach air blast risk assessments in a way that can be incorporated in the day-to-day operation of a mine. Previous methods of assessing air blast risk were tedious and results were often unrepeatable.With the extension of the E48 Lift 1 extraction level, it was necessary to assess the air blast risk for the extension drives and develop operational guidelines for production from the extension. A review of the methodology for assessing air blast risks revealed substantial improvement opportunities.This paper outlines the principles used for air blast risk assessments at Northparkes Mines and the methodology employed to achieve efficient, repeatable and auditable results.CITATION:Vejrazka, C, 2016. Northparkes Mines’ current air blast risk assessment practices for block caving operations, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 257–264 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Thomas L. Theis

The use of a suspended growth system of T. ferrooxidans attached in a film to individual particles of bentonite and operated as a sequencing batch reactor has been shown to be a practical way of oxidizing ferrous iron in acid mine drainage. This component followed by limestone neutralization is both a technically and economically feasible approach to the treatment of these wastewaters in comparison to existing and proposed methods. The advantages, in addition to less expense, are greater safety, acceptable treatment at a lower pH, lower solids buildup, less danger of overtreatment, and greater flexibility in operational characteristics. In this report data on the continuous bench scale operation of the system under a variety of conditions shows sustained levels of oxidation in excess of 9%. A cost analysis projects capital and operating costs of $80/1,000 m3 of wastewater.

Jan 1, 1982

By Sutham Niyomwas

The Fe-TiC composite powder was synthesized in situ by carbothermal reduction of ilmenite. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The effects of the reaction temperature (1300 °C - 1500°C) and milling time of precursors on the Fe-TiC conversion and powder morphologies were investigated using XRD and SEM method. The synthesized products showed that composite with iron matrix and titanium carbide as a reinforced phase was formed.

Jan 1, 2006

By S. I. Freedman

Coal-oil mixture (COM) combustion technology is regarded by the Department of Energy as near term, and potentially applicable to existing utility and industrial steam generators and for injection into blast furnaces. From work done previously, it has been established that COM can be burned in existing boilers, into blast furnaces. Therefore, the issues being addressed by the current DOE program are: (1) determination of best available technology to achieve environmentally-acceptable long-term reliable operation and (2) determination of applications for which COM can be utilized economically. Some of the technological options have begun to be determined by projects already under way. However, many projects are still in the early stages of development.

Jan 1, 1978

By Martin B. Zimmerman

It is becoming evident that traditional methods of econometric analysis are inadequate in estimating-the long-run supply of minerals. Econometrics is limited to extracting estimates from observations of the theory predicts that the least cost deposits will be exploited first.1 The estimation of parameters from past data then must lead to biased projections of the future. Mining conditions in the future will be worse than in the past and it is the impact of the future conditions on cost that we need to know. In this paper we present a methodology for dealing with this problem. We estimate a "cumulative cost" function that yields the long-run marginal cost of mining as a function of cumulative output produced over time.2 This is relatively easy to do for coal mining in the United States where exploration for new deposits is not a major factor in supply. The first step of the procedure relates cost to the rate of output and to the geological conditions of the mine. The second step combines geological information on remaining deposits with the cost function to yield the cumulative cost function. A central theme of both these steps is the interaction of economics with geology. The best deposits are selected first and in each step of the estimation allowance must be made for this fact. The problem of depletion is part of the general problem of structural change. The change through depletion in the nature of the exploitable mineral stock is only one factor that calls for an analysis sensitive to the changing circumstances of the industry. The factors impinging most heavily on the coal industry today are the strict environmental regulations legislated

Jan 1, 1977

By G. W. Murrie

A geologic study of the Mary Lee Group of coalbeds in the Black Warrior coal basin was undertaken to examine coal stratigraphy and determine regional trends and extent of the coalbeds. The area investigated encompasses 835 square miles in Jefferson, Walker, and Tuscaloosa Counties, Ala. More than 700 core logs were used to construct a structure map, coal, interval, and overburden isopachs, and cross sections. There is evidence that structure affected sedimentation. Coalbed isopachs indicate the Mary Lee Group was deposited in fluvial-deltaic and low-lying coastal plain environments. The Mary Lee coalbed is the only coalbed which is continuous throughout the area, commonly with two benches which have a combined thickness of 2 to 12 feet. The Mary Lee coalbed changes rank in the basin from high-through medium-to low-volatile coal. The methane gas potential of the Mary Lee Group coals is estimated to be greater than 1 trillion cubic feet. There is an excellent correlation between the orientation of surface cleats with those measured underground in the Mary Lee coalbed. The face cleats roughly parallel the axes of the area's folds and trend northeast-southwest.

Jan 1, 1976

By Brendan Reilly, Jon Isaacson, Paul McDermott

Kenny/Shea JV is constructing the water intake tunnel for the new Elm Road Generating Station, a supercritical coal-fired power plant in Oak Creek, Wisconsin, being built by Bechtel Power Corporation. The intake tunnel system consists of a temporary mining shaft, pump house and intake channel riser shafts, and four lakebed intake shafts. An 8.33 m diameter, 2,800 m long TBM mined rock tunnel is being constructed to connect the shafts. The intakes are located 2.4 kilometers offshore in Lake Michigan. The shafts and tunnel are being constructed in glacial tills and Silurian Dolomite. The estimated tunnel completion is December 2007.

Jan 1, 2007

By S. H. Miller

Biodegradable hydraulic fluids can save tens or hundreds of thousands of dollars in fines and clean up costs in the event of a hydraulic fluid leak or spill. When properly selected, applied, maintained and monitored, a biodegradable fluid will have a long useful life and will protect equipment as well as or better than conventional petroleum based hydraulic fluids.

Jan 1, 2000

By J. I. Paige

As part of a continuing effort to develop technology that maximizes mineral and metal recovery from domestic resources, the Bureau of Mines investigated a method to totally utilize copper converter slags without recycling them back through the matte smelting furnace. The research was directed toward (1) recovering the contained copper in converting slags by producing a recyclable copper-iron matte, (2) carbothermically reducing the slags to recover the iron, and (3) producing slag wool from the depleted slags. This report deals with the reduction of three industrial converting slags, containing 2.0 to 7.3 wt-pct Cu, in an 800-kVA electric arc furnace to produce a recyclable copper-iron matte. The addition of sufficient iron pyrite to provide 29 to 113 pct of the stoichiometric sulfur (based on producing 40-pct-Cu matte) produced a recyclable matte (36 to 61 pct Cu) at an energy consumption of 520 to 700 kWh per ton of solid material charged. The expected energy saving for treating molten slag in an electric furnace (5-to 9-MVA range) is about 400 kWh per ton of molten slag treated.

Jan 1, 1982