Search Documents

By Edgar Stanfield

Since April, 1923, the Scientific & Industrial Research Council of Alberta has had an analyst, Mr. W. P. Campbell, steadily employed analyzing coal samples taken by the provincial Mine Inspectors. Mr. Campbell has also analyzed a number of coal samples taken by one of the Council's Geological Survey parties. We have thus, at the time of writing, over four hundred analyses of Alberta coal, made by the same analyst, and strictly comparable. These samples come from widely distributed points, some 88 townships being represented. The stream of samples is still flowing in, and it is hoped by the end of this year that the number of townships represented will be increased at least fifty percent. The time has arrived to publish some of the data collected; but it must be clearly understood that this is merely a progress report, subject to revision as further information is obtained. Three hundred and fifty-three coal mines in the province were operated during 1923. The production per mine varied from 5 up to 500,000 tons. With this number of mines to examine (and fresh mines are being opened every year) it is a large task to make even a proximate analysis of representative samples from every mine. Any chemist will appreciate the fact that to make ultimate analyses representative of even the larger mines will be a long and tedious task. It has seemed better to make a comprehensive survey by proximate analysis and determination of calorific value before beginning the more thorough survey by ultimate analysis. This paper, therefore, deals only with proximate analyses and calorific values; and, owing to limitations of time and space, does not deal with other chemical and physical characteristics of coal, such as storage quality and fusibility of ash, important though these are.

Jan 1, 1925

By Terry J. Close

A mineral resource survey of the 940-square-mile (2,434 km2) Hells Canyon study area, which includes Hells Canyon Wilderness, Snake and Rapid Wild and Scenic River's, and adjoining roadless lands in Oregon and Idaho, indicates the area is highly mineralized. Thirty-four lode deposits within the study area have resources totaling about 31 million tons (28 million t) containing copper, silver, zinc, gold, and lead; another 42 lodes, not sufficiently exposed to allow resource estimates, are believed to have mineral potential. The most important deposits are copper-, silver-, zinc-, gold-, and lead-bearing volcanogenic occurrences, followed by silver-and copper-bearing contact replacement (tactite) deposits; other lode occurrences are relatively unimportant. The most important placer deposits occur at Dry Diggins; placers along the Snake River are small and scattered. The study area has extensive deposits of limestone and sand and gravel; it has little potential for energy resources.

Jan 1, 1982

By D. I. Bleiwas

Bureau of Mines personnel evaluated the potential availability of nickel from 151 deposits in 18 market economy countries and selected 126 for detailed analyses. An evaluation was made of tonnage-cost relationships indicating the quantity of nickel available at various total costs of production expressed in dollars per pound nickel, including a 15-pct rate of return on the invested capital. The 126 deposits studied contain approximately 73 million metric tons (t) of nickel. An estimated 52 million t is available from laterite deposits, of which less than 2 pct could be produced at $3.50/lb Ni, about equal to the average published price of nickel in 1981. Approximately 21 million t of nickel is available from sulfide deposits, of which about 10.0 million t can be produced at $3.50/lb. Sensitivity studies performed for both laterite deposits and sulfide deposits indicate that the total cost of nickel from laterites is most sensitive to increases in energy costs, and that sulfides are most sensitive to increases in labor costs; sulfides are also sensitive to changes in byproduct revenues. In 1983 the Nickel Mountain mine in Oregon was the only U.S. producer, though development continued on the Gasquet property in California. Of the total 5.1 million t of recoverable nickel in the United States, about 20 pct is available at or below $3.50/lb.

Jan 1, 1984

By L. S. Sundae

The Bureau of Mines conducted a series of tests to compare the cutting forces required by radial and point-attack bits when making similar cuts. Three radial and four point-attack bits were tested in two coal mines using the Bureau's in-seam tester to measure coal-cutting forces in situ. Tests were also conducted to investigate the effects of weathering and cleating. The test results show that in each case, at a specific clearance angle, the radial bits required less tangential and much less normal force than the point-attack bits. The resultant of the cutting forces for some types of cut was 50 pct less at mine 1 for radial cuts compared to cuts with the best point-attack bit, and 40 pct less at mine 2. There was some difference between three types of radial bits, but it was not as significant as the difference between each type of point-attack bit. Cutting coal perpendicular to the cleat planes required less cutting and normal force than the same type of cuts parallel to the cleat planes. Test results showed no effect due to weathering on cutting force data. Cutting parallel increased forces only because cuts were made in the rock band.

Jan 1, 1987

By Eduardo Pimenta de Melo, Rambabu Pothina, Rajive Ganguli

Sensors are everywhere in the mining industry, with sensor information being used to monitor and operate processes. Therefore, when sensor information is wrong, economic losses can occur. Unfortunately, sensor errors are usually not detected till they become large. This is problematic as most calibrate their sensors no more than once a year (Beamex, n.d.). Using principles of data mining, where all relevant information is tapped to glean hidden information, Pothina [8] designed an algorithm to detect errors in temperature sensors in gold stripping circuit in Pogo mine, Alaska. This paper continued his work by analyzing the behavior of the algorithm on baseline data and testing the algorithm in new data and under more rigorous conditions. It also made a change to the algorithm. The modified algorithm performed very well in the new data. It also worked well under the new error conditions. Three types of errors were seeded, a fixed additive error (+ 2%), a fixed subtractive error (− 2%), and a noisy, normally distributed error, with a mean value of + 2%. Artificially seeded errors were detected within about 20 gold stripping cycles. Inherent bias in operation impacted algorithm performance by increasing the number of cycles needed to detect errors. This paper reinforced Pothina’s [8] conclusion that when data mining approach is used, sensor errors can be detected even when they are pretty low. Significant economic losses can thus be minimized.

By Euler De Souza

This paper presents a study conducted to assess sillmat behaviour during undercut mining and to provide a comprehensive understanding of the effects of arching and sillmat thickness on stability. The design study investigated the effects of such parameters as stope width and height, closure strains, orebody geometry and inclination, wall roughness, fill properties and cure time on the stability of cemented sillmat during undercut mining. Arching effects have been quantified based on centrifuge modeling studies for the different mining conditions. Observations have indicated that the degree of arching is a function of stope geometry, wall roughness, fill cohesion, and wall closure. Arching effects increased with decreasing stope width, increasing backfill cohesion and frictional resistance, increasing wall roughness and with wall closure.

May 1, 2002

By K. Baris

Methane (CH4) present in coal seams, generally known as Coalbed Methane (CBM), Coal Mine Methane (CMM) or Coal Seam Gas (CSG), is a major energy source, as it is the primary constituent of natural gas. At the same time, released methane is a potent greenhouse gas (GHG) and a major safety hazard in underground mining operations. Therefore, a considerable effort has been undertaken to develop coal bed methane extraction and utilization technologies that can achieve both environmental and safety benefits. Countries with significant coal reserves and gassy seams, i.e., USA, Australia, Canada, China, India, Poland and Germany have developed mature methodologies and practices to extract, before and during mining, and utilize significant amounts of methane from coal seams. Nevertheless, on a global scale, methane recovery remains untested and many technical and economic challenges require urgent attention. The research presented in this paper, sponsored by the United States Environmental Protection Agency (EPA), is focused on the Zonguldak Basin, the only hard coal region in Turkey. The basin is known to contain very gassy coal seams and consists of three major regions: Armutcuk, Zonguldak and Amasra. Among the three, the Amasra coalfield is considered as the most favorable for CBM recovery, as it comprises of deeper coal seams and where a private company, Hema Enerji A.S. (Hema) is already developing coalbed methane production facilities. This study aims at developing a reservoir model to predict the potential CBM recovery from the CBM-2 well, the only producing CBM well drilled by HEMA Enerji A.S in the Amasra coalfield. History matching was utilized to model the 15-day production data and uncertainty analysis was performed to estimate the optimum values for the reservoir parameters. The produced model yielded an average production rate of 143 m3/day for 10 years. The total amount of CH4 to be produced during this period was 0.53 million m3. Furthermore, the total amount of GHG to be avoided was estimated at 6585 tCO2e.

Aug 1, 2013

By Kirk A. Mcintosh

Augered, cast-in-place (ACIP) piles have been utilized in the United States for a wide range of projects since the 1950's. Due to the cast-in-place nature of the installation method (and lack of a driving criteria); however, ACIP piles have not been readily accepted by some practicing geotechnical and structural engineers. Since ACIP piles were initially developed, the installation equipment and techniques have been improved and refined and the number of experienced contractors has significantly increased. Over the past 10 to 15 years, the pile type has experienced significant growth in the United States (particularly in Florida) because engineers have become more knowledgeable and comfortable with its use. The Miami area, in particular, has experienced considerable growth in the utilization of ACIP piles primarily due to their usage on the $1 billion Miami Metrorail System project in the early 1980s. The economic advantages over other deep foundation types, coupled with some unique installation advantages, have shown that ACIP piles can be a viable foundation alternative on many projects. Even though ACIP piles have gained respect in the private sector, the pile type has generally not been readily accepted by government transportation agencies. The reluctance to readily accept this foundation type stems primarily from the quality assurance aspect of cast-in-place pile construction. Additionally, there has not been much research activity on this foundation type, technical papers, formal associations (other than the DFI), or a concerted effort to standardize the industry. This paper serves to discuss the state of practice for ACIP pile installation in the state of Florida.

Jan 1, 1997

By J. Andrew Cornier, Mike Cooper

"Upon successful completion of the AG/SAG Mill project (Cooper et al., 2001) the Brunswick Mine concentrator was configured with single line processing through the AG/SAG mill, followed by two parallel ball mill and flotation circuits. The Stage Grinding project was undertaken to utilize a pre-flotation stage on the AG/SAG mill primary cyclone overflow and simplify the flowsheet by consolidating the two ball mill and flotation circuits, resulting in single line processing fi-om AG/SAG mill to final concentrate. Concurrently, the reclaim water supply capacity was increased to enable flotation cleaning at lower percent solids.Benefits from the Stage Grinding project include revenue enhancement from increased zinc grade and recovery combined with additional lead recovery. Further benefits included a reduction in the number of process pumps, reduction in loss associated with spillage to sumps and process simplification through efficient use of equipment layout.The Stage Grinding project was implemented in six phases over a period of seven months in 2000. Each phase was commissioned during scheduled concentrator shopdays with minimal additional downtime required. One year after project approval the Stage Grinding project was completed at a total cost of $1 1.8 million.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is one of the world’s largest leadzinc mines. Milling of ore began in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore fkom the No. 6 open pit located several kilometers away. In 1980 the pit was exhausted and the concentrator rationalized to accept a design feed rate of 10,500 tomes per day from the No. 12 mine. In excess of 100 million tomes have been milled to date, representing over three-quarters of the known reserve. The concentrator employs differential froth flotation to produce lead, zinc, copper and leauzinc bulk concentrates. The ore is massive sulphide, with approximately 20% valuable minerals, 60% pyrite and 20% silicates."

Jan 1, 2002

Roof falls in coal mines typically occur in or around intersections and this has not changed in the last two decades. This research develops an improved scientific understanding of stress distribution and associated failure behavior around 4-way and 3-way coal mine intersections. Three-dimensional numerical analyses were performed to determine factors that influence intersection stability. The analyses used Hoek-Brown failure criterion. Failure zones around 3-way and 4-way intersections were developed. Intersection span and horizontal stress have a major influence on intersection stability. For the 4-way intersection, pillar corners across the intersection fail first and lead to progressive failure of immediate roof and floor layers. The mechanism of failure is similar for the 3-way entry but the shape and extension of failed zones differ. Coal ribs mostly fail due to tensile stress, while roof and floor strata fail due to shear stresses. Rib corners fail due to a combination of shear and tensile stresses. In addition to stress distribution; safety factor contours analysis was performed to assess stability of intersections.

Feb 27, 2013

By Robert J. Coutts, Dan A. Payne

"The Broadmeadow mine is a punch longwall mine owned and operated by BHP Billiton Mitsubishi Alliance (BMA) in the Bowen Basin of Queensland, Australia. In 1999, an exploratory adit was driven as part of the feasibility study for the establishment of the mine. Subsequent development of the mine in 2004 started some distance away from the initial test adit. Ten years later, the trial adit would be used as the headgate of the 5'h longwall panel. However, multiple roof falls had occurred in a heavily jointed area over a distance of 1, 000 ft (300 m) during the past 10 years. Due to the immediate coal roof, low stress environment and time, some of these falls had progressed to 38 ft (11.5 m) above the mining floor. As a result of the extensive work involved and safety implications of trying to recover the roof falls conventionally, a strategy was developed to fill these roof falls with a cement based product from the surface, down boreholes, and redrive the roadways through the consolidated roof fall material. This paper describes the process of rehabilitating these roadways, the results when the roadway was redriven and the headgate performance as the longwall mined through the area.INTRODUCTIONBMA operates 7 open cut and 2 underground mines in the Bowen Basin of Queensland, Australia producing over 50 mt per year of high quality coking coal. As a result, BMA has established over 150 miles (250 km) of open cut highwall.Broadmeadow Mine is a punch longwall mine located 22 miles (35 km) north of Moranbah in Queensland, Australia on the western limb of the Bowen Basin Coal Measures (Figure 1). Broadmeadow Mine commenced development in 2004 and began longwall operations in 2005. Broadmeadow is currently completing the fifth longwall panel and produces over 4 Mt per year of high quality coking coal. Mining is undertaken in the Goonyella Middle Seam, which is 21 to 25 ft (6.5 to 7.5 m) thick in the current mining area.The mine layout required the use of an old exploratory gateroad as the headgate of its 5th longwall. This gateroad had experienced numerous large roof falls and required extensive rehabilitation."

Jan 1, 2010

By Christopher C. Jobes, Alan G. Mayton, Timothy J. Matty, Joseph P. DuCarme

Mining injury statistics show that a significant number of back, neck, and head injuries are linked to exposure from vehicle vibration. Use of a suspension seat is a common way to isolate the vehicle operator from the adverse effects of vibration exposure. Thus, researchers at the National Institute for Occupational Safety and Health1 – Pittsburgh Research Laboratory (NIOSH – PRL) performed laboratory studies on four passive and two semi-active seat suspension designs. These are typical of seat suspensions commonly found on large off-road heavy surface mining, construction and agricultural vehicles as either replacement or original equipment manufacturer (OEM) systems. One included a pneumatic (air bladder) spring mechanism. The fifth and sixth suspensions were a NIOSH magnetorheological (MR) semi-active damper design based on the pneumatic (air bladder) and one of the coil spring suspensions above. These suspensions were modified with a commercially available MR damper substituted for the OEM damper. These six seat suspension systems were tested and analyzed, for vertical vibration only, using the ISO 5007 Standard [1]. This paper describes the laboratory vibration tests using a MTS® shaker table and discusses the results obtained for the different suspension designs and highlights the rheonetic technology studied. Implications of the seat suspension designs relative to their capabilities for isolating vehicle operators from vibration exposure are discussed. Results for suspensions 1 through 3 showed frequencies of isolation from 2.1 to 3.0 Hz using the 40-kg (88-lb) mass and from 1.65 Hz to 1.8 Hz using the 80-kg (176-lb) mass. Suspension #4, in tests with only the 80-kg (176-lb) mass, showed an isolation frequency of 3.7 Hz. With the MR damper added to seat suspension #4, the peak transmissibility was lowered from 1.3 to 0.95 and showed a corresponding downward shift in frequency from 2.25 Hz to 1.4 Hz. In fact, the results for suspension #5 (the MR damper added to seat suspension #4), using test #3 conditions of the programmed control algorithm, showed isolation (attenuation of transmitted vibration) throughout the test frequency range from 1.0 to 6.0 Hz.

By S. Harteis, D. Dolinar

Many mining operations rely on bulkheads to provide a barrier between impounded water or slurry and active mine workings. However, bulkhead failures could cause and have caused catastrophic flooding that puts the underground workforce at risk. The National Institute for Occupational Safety and Health1 (NIOSH) in collaboration with the Mine Safety and Health Administration (MSHA) is conducting research to evaluate the adequacy of existing design practices for water and slurry bulkheads. A key component of this research effort is documentation of the performance history and design parameters for bulkheads installed in underground coal mines during the last 20+ years. This research is part of a larger effort to develop general design guidelines and procedures for constructing and maintaining bulkheads that will help to ensure their long-term structural integrity, while significantly reducing the inundation risk for miners. This paper presents the results of NIOSH’s research to identify state-of-the-art bulkhead designs, including design criteria, leakage monitoring systems, and emergency warning systems. Underground observations and evaluations of existing bulkheads suggest that the most important design factors influencing their performance are the interface of the bulkhead with the surrounding strata and the potential magnitude of the hydraulic pressure to which they may be subjected. When a bulkhead has failed, leakage has generally been through the surrounding strata or along the bulkhead/strata interface, with the failure potential along the interface increasing with hydraulic head. It was also determined that development of a monitoring program to ensure the long term structural integrity of bulkheads is an important safety consideration. Current monitoring procedures range from weekly visual inspections to constant monitoring via pressure transducers and fluid level indicators. Where possible, these devices are used in conjunction with a computer based mine monitoring system to alert mine personnel when an emergency condition exists at the bulkhead installation.

By Francis B. Foley

In examining steel under the microscope, one is constantly confronted with structures that are difficult to interpret. Recently, in a collection of samples for exhibition purposes, the writer found a piece of open-hearth runner metal, 2 in. (50 mm.) in diameter, that had been fractured for use as a sample of cast-steel structure. On polishing and etching a section for the purpose of photographing a field to typify the microstructure of steel in the "as cast" condition, a variety of structures was found (Fig. 1) so arranged as to arouse interest at once. For a distance of about 0.065 in. (1.6 mm.) from the skin of the runner, normal ingot structure was found (Fig. 2); this was followed by a zone, about 0.215 in. (5.5 mm.) wide, of considerably lower carbon content in which occurred a most pronounced Widmannstattian structure (Fig. 3); from this point on to the center of the runner, the metal was again of normal ingot structure (Fig. 4). Representative samples taken from the metal in the three zones showed the following analysis: Carbon Nickel Chromium Per Cent. Per Cent. PeR Cent. Metal from skin........................... 0.34 1.26 0.63 Widmannstattian zone.................... 0.21 1.18 0.63 Metal from center......................... 0.34 1.32 0.67 Such a condition might result from decarburization followed by recarburization of the skin. This section came from one of the branch runners to the bottom of the mold, not from the main runner, and it is difficult to conceive of decarburization occurring in this portion of a runner. If the metal were stripped while quite hot, some oxidation would take place but the recarburization is unaccounted for. It could not occur by segregation after solidification—the tendency then is for diffusion and homogeneity. The following seems to fit the conditions and is offered as an explanation. The outside layer of normal structure 0.065 in. (1.6 mm.) thick was chilled on the walls of the runner brick when the molten metal first entered the runner. As the molten metal flows by, the outside of the stream

Jan 1, 1920

By J. P. Van Cruyningen, M. J. Puro

"A 2400 acre extension to the existing Tailings Area is under development at Inco's Copper Cliff Milling operations.The new area is being developed in stages as production levels dictate thus minimizing immediate capital expenditures while permitting disposal operations to proceed as further site work progresses.The first stage of the new storage site will be fully operational by early 1987 and will include a 400 acre site specific to the storage of Pyrrhotite rejected from milling circuits. The Pyrrhotite site is located in the centre of the Tailings area and is designed for water cover throughout much of its projected life.The new development incorporates perimeter dams designed to operate with low phreatic levels for maximum structural stability. Acid seepage water is collected behind secondary impermeable dams for return to the Tailings Pond.Tailings are deposited by up-stream methods permitting segregation of coarse fractions for use in future lifts of the perimeter dams."

Jan 1, 1987

By Victor A. Phillips

A series of specimens of a Cu- 3.23 pct Co alloy were prepared with particle diameters from zero to 590A. The samples were then cold-rolled 95 pct and the effects of the particle size on the behavior on annealing for hr at temperatures between 100" and 900°C were studied (by hardness, light, and electron metallography). Particles, particularly for d r 105 to 590A, greatly impeded softening and vecvystallizn-tion, and tended to give elongated grains. Particles deformed fairly homogeneously with the ,matrix, be- IN a previous study by the author,' the growth of cobalt-rich precipitates was followed electron microscopically in Cu-3.12 Co alloy as a function of aging, typically at 650°C. The coherent spherical precipitates grew to 520 + lOOA average diam before spontaneously losing coherency and developing (111) facets. Stretching a few percent after precipitation 2aused loss of coherency to occur sooner at about 220A average particle diam. The particles apparently retained their fcc structure after loss of coherency. coming lau2ellae. For d = 55 to 180A, these lamellae gave streak-contrast effects apparently due to coherency strains , and spheroidized on annealing at 600" to 650°C, forming coherent particles. Particles of d = 250 ov 320A lost coherency during t-olling, giving incoherent lamellae. Recrystallization apparently occured by growth of new grains into unrecrystallized (recovered) material at temperatures below that at which cobalt atoms had much mobility. The present study was undertaken to explore the effect of cobalt-rjch particles of various average sizes from 50 to 600A diam on the isochronal annealing behavior of copper after heavy cold rolling. The previous work' was used as a guide in preparing the two-phase series of prerolling structures. The solution-treated alloy was also rolled for comparison. A further question of interest in the present study was whether dislocation and particle hardening were additive, since the prerolling structures covered the full range unaged - peak aged — overaged, and further precipitation might occur on annealing after cold rolling. Although there have been exhaustive studies of the isothermal2"6 and is~chronal annealing behavior of

Jan 1, 1967

By Alan D. Curtis

A standard planning block model for Phelps Dodge North America Operations has been developed to improve mine planning efficiency and performance in a skill starved environment. The model saves time on software management and training, consolidates data and standard information/output, enhances evaluation and strategic process, and improves communication between sites.

May 1, 2007

By R. L. Schmidt

One of a series published by the Bureau of Mines covering research investigations in rock drillability, this report of field drilling results extends earlier laboratory findings and provides a relatively simple procedure for predicting percussive drilling rates with reasonable accuracy. Two percussive drills mounted on a truck were used to drill a total of 25 rock types, and the results were used to develop a prediction equation. The equation was tested on a set of unrelated laboratory percussive drilling data, and the comparison between predicted and actual rates is shown in tabular form.

Jan 1, 1972

By R. W. Stahl

An award is a form of recognition given for superior performance in a special field of endeavor. Each year awards are given by the Joseph A. Holmes Safety Association and the National Safety Council to mineral industries' mines, quarries, and plants that have worked a specific number of man-hours without a lost-time injury. These awards have a dual significance in that they prove that efficiency can be attained without injury to persons. Safety awards do not result from luck or good fortune but do result from sincere desire coupled with sufficient effort and cooperation to achieve a desired goal.

Jan 1, 1963

By C. F. Winquist

The Bureau of Mines is engaged in research to evaluate the effects of cutter bit wear at coal mine faces. This paper addresses one element of conical bit wear, bit rotation. A discussion on mounting configura-tion and bit forces and their effects on rotation is presented. The effects on rotation and bit forces of bit attack angle, cutting depth, and skew are determined for two types of conical bits during linear cutting of sandstone-inclusive rock. The results indicate that a 10° negative skew angle and 35° attack angle produce the maximum rotation of 17.5° for each foot of cutting. Data on bit rotation and bit forces are presented in an appendix.

Jan 1, 1985