Search Documents

By James F. McConnell

Federal and State sulfur oxide emission and ambient air quality regulations have been implemented to fulfill the requirements of the Federal Clean Air Act Amendments of 1970. Primary and secondary air quality standards have been established at levels considered necessary to assure the protection of the health and welfare of the public. Standards of performance under this Act have been established to control the rate of sulfur oxide emissions from individual sources so as to protect and to improve the quality of the Nation's air. The new source standards of performance were made rigorous for large coal burning stationary sources. This has had a severe impact on the electric utilities that operate the coal fired steam electric plants which are the largest consumers of the Nation's coal production. States have taken different approaches in State Implementation Plans (SIPS) as approved by the Federal Environmental Protection Agency. Some states, such as Pennsylvania, have chosen to permit moderate SO2 emission rates from existing sources which are not in critical air basins. All are required to meet primary and secondary air quality standards and to limit sulfur oxide emissions from new large stationary sources to a minimum of 1.2 LBS of S02/MMBTU fired. This re- quires a fuel sulfur percentage of about 0.7 for a 12,000 BTU/lb coal. In an effort to develop strategies and technologies to conform to performance standards while continuing and hopefully expanding the utilization of the Nation's coal supply, the electric utilities, the Federal and State regulatory agencies, and other industries and government agencies are considering several alternatives. 1. Natural low sulfur coal 2. Flue gas desulfurization - (FGD) non-regenerative and regenerative 3. Coal gasification 4. Liquefaction and solvent refined coal 5. Fluidized bed combustion 6. Chemical coal cleaning 7. Physical coal cleaning Of these options, only the first and the last can be considered to be widely used in full commercial practice at this time. FGD has certainly demonstrated technical and operating feasibility and is close to being in full commercial practice but it remains to be seen if the large systems under construction are economically and environmentally optimum.

Jan 1, 1975

By L. A. Haas

A kinetic study of the carbon deposition reaction was undertaken by the Bureau of Mines as part of a broad investigation of metallurgical reactions in the iron ore blast furnace. The disproportionation of carbon monoxide on iron pellets was investigated at carbon monoxide pressures between 0.5 and 2 atmospheres (absolute) and temperatures from 400° to 1,075° C. Gas flow in the range from 0.25 to 0.85 standard liter per minute was found to have little effect on the reaction velocity. The addition of nitrogen and helium to caron monoxide exerted only a dilution effect on the rate of carbon deposition. However, an addition of 1 percent hydrogen increased the rate about 100 times. Small amounts of carbon dioxide in the inlet gas exerted little effect on the rate of carbon deposition. The maximum rate for carbon deposition in the first 2 hours occurred at 550° C. The apparent molar activation energies at various stages of the reaction were found to vary from 13 kcal initially to 36 kcal during the latter stages of the reaction. The reaction rate behavior was tentatively explained by an adsorption step followed by the diffusion of iron through a shell of inactive iron carbide.

Jan 1, 1968

By Dan Nilsson

INTRODUCTION A company must have an objective, and that usually is to earn money. In some countries an objective can also be to reduce unemployment in an area or to develop nonindustrialized areas. Government-owned companies can also have as an objective that of serving the com¬munity. This discussion is limited to the consideration of normal companies wanting to earn money. Such an objective, however, has to be defined in more detail. It is not satisfactory only to maximize the total annual profit from, for example, a mining project. In comparison with most other branches, the mining in¬dustry is very capital intensive. When starting a new project, the mining company must invest a lot of money in mines, ore treatment plants, etc. It is normally many years before any income is received from the ore. Fig. 14 illustrates the payments for a new mining proj¬ect with an expected lifetime of 10 years. Whether this project is a profitable one depends on a lot of things. If the company has a shortage of money, it can be impossible to finance the project. Even if the company has enough money, the management may think that perhaps the project may not return the money fast enough. Such limitations will not be discussed here. Suppose that the company has internal funds from its own operation or can borrow them. Since the mining company must invest the money in advance, it is not satisfactory only to add all of the costs during the mine's lifetime and compare them with the total income during the lifetime. The company must include the time value of the capital. In this appendix, the basic investment theory neces¬sary to judge the profitability and costs of mining proj¬ects will be discussed. INVESTMENT THEORY Time Value of Money If a private person has a dollar and puts it into a bank, he or she will receive interest. If the interest rate is r%, the value after one year will be $(1 + r), after 2 years $(I + r)2 , etc. The interest rate represents the time value of money. If the same person wants to have $1 in the bank af¬ter one year, he or she has to put $(1 + r)-1 in the bank today. If the person wants $1 after 2 years, it is neces¬sary to put $(1 + r)-2 into the bank today, etc. So one dollar today is worth more than one dollar tomorrow. It is, of course, not correct to compare money at differ¬ent times since each dollar has a different value. It is necessary to transform all payments to the same point in time. That is called the calculation of the capital value of a cash flow, and to do this an interest rate is used. In the same way, the cash flow from a project like that shown in Fig. 14 can be translated to any other point in time. Most common is to translate all payments to the beginning of the mining period. That capital value is often called the present capital value. Interest Rate What interest rate will the company use? A com¬pany, just like an individual, has the basic alternatives of keeping its money in the bank and receiving interest, or borrowing money from a bank and paying an interest rate. The interest rate represents the time value of money for the company. If the company has a shortage of money, or many good potential investment projects, it has to use a higher interest rate than if it has a lot of money available. Most companies also increase their interest rate as a hedge against the risk involved by using money for uncertain investments, because of taxes, etc. Capital Value When the interest rate has been decided, it is possi¬ble to estimate the capital value of a project. Here the discussion will be limited to the estimation of present capital values. Suppose that one wants to know the present capital value of $1 (Fig. 15), which will be received after n years. To transform it n years back in time, one must multiply it by the factor (1 + r)-, where r is the inter¬est rate the company uses. Table 1 gives these factors for different years and interest rates. Example: At the end of year 5 a mining company has to invest $50 million in a new mine. What is the present capital value at the end of year 0? The company uses an interest rate of 15%a.

Jan 1, 1982

Solid. dense, air-cooled slag can fulfil most, if not all, the functions of natural stone for civil engineering purposes. The value of pumice, also, has long been appreciated, and processes for the manufacture of similar synthetic material for light-weight concretes and insulating fills have been developed in past years.Foamed slag is, in effect, blast furnace pumice and is often referred to on the European continent as metallurgical pumice. It is made by the treatment of molten blast furnace slags with a critical quantity of water during which process the slag cools and expands into a sponge-like mass. The connection between foamed slag and air-cooled slag is also considered and a basis for density control given.All blast furnace slag cannot be foamed to give a product which would comply with B.S.S.877; 1939 Foamed Blast Furnace Slag. A large proportion of the total output of molten slag lacks the necessary inherent properties. This investigation attempts to discover the conditions necessary for the production of foamed slag capable of meeting the British specification.EARLIER WORKIt was generally accepted (Parker, 1951; Gallai-Hatchard, 1955) that the spongy structure of foamed slag was caused mechanically by steam trapped in the slag when it was poured into water. It was assumed that slags which would not foam would not trap steam, because their viscosities and surface tensions were unsatisfactory, on account of temperature and/or composition. The earliest systematic investigation was made by Frisak (1923) who attempted to establish a limiting chemical composition for foamable slags. He decided that foamable slags covered most blast furnace slag compositions on the basis of silica, alumina, and lime, and further "that the replacement of lime by magnesia up to 15 per cent has no noteworthy effect on foamability, that moderate quantities of alkalis are not deleterious, that sulphur raises the foamability and that MnO is only deleterious in the presence of 1...

Jan 1, 1963

Computational models are very useful for studying many of the physical mechanisms which can cause sample bias. Within such models we can predict the trajectories of all individual particles and thereby make observations which are not possible for physical systems. Physical mechanisms highlighted include congestion at the cutter aperture, particles bouncing over the cutter aperture, air drag on fine particles, waves of material being bulldozed off the belt by the upstream side of the body of square cutters, and particles being thrown by the leading edges of cross-belt cutter blades. Having identified relevant physical mechanisms for an existing cutter, we can estimate the extent to which they are likely to result in unequal representation of portions of a stream of material and thereby estimate the maximum likely sample bias.

Mar 1, 2010

By R. A. Cummings

Certain roof shales in coal mines deteriorate upon exposure to the atmosphere, causing difficulties in the mining operations and adding to the cost. This report presents the results of both field investigations, in a West Virginia mine, and laboratory studies on the effects of atmospheric moisture on roof shales. Based on these observations, a conceptual procedure is presented on how shale deterioration might be predicted during exploration, and guidelines are given as to how air tempering or conditioning chambers may be designed to reduce moisture effects. Recommendations for further studies are included. An annotated bibliography of the literature constitutes the second volume.

Jan 1, 1981

By W. H. Oppelt

Two exploratory gasification tests of limited duration were made at Dorsten, Germany, with strongly coking Pittsburgh-bed coal in a fixed-bed pressure gasifier. To reduce the coking potential of the Arkwright coal, ash refuse from the gasification of Dorsten (Leopold) coal was added to pre-pare coal-ash mixtures which contained nominal 20 and 30 percent ash. Major adjustments in principal process variables at the beginning of the tests resulted in wide fluctuations in the rate of gas production, gas offtake temperature, and carbon dioxide concentration in the gas. Because a higher steam-to-oxygen ratio was used in the tests than was customarily employed for routine operation, gas production was lower, and steam and oxygen consumption was higher. After operating conditions had been improved, the results of a 12~-hour-long test with addition of sufficient ash refuse to obtain a nominal 30 percent ash concentration indicated that operation is feasible with this coal mixture using a fixed-bed pressure gasifier equipped with a rotating coal distributor and stirrer.

Jan 1, 1966

By G. D. Schena, M Zanin

A numerical approach is presented for predicting the liberation of phases during comminution, with direct calculation of a liberation spectrum giving the fraction of the particulate system in each narrow size-composition class. The numerical model uses a Poisson flat process for stochastic generation of the non-convex three-dimensional Poisson polyhedral textures and the system of fractures that give rise to convex fragments. With this numerical approach, there is no need to assume random uniform isotopic fracture (lack of selective liberation); only computational geometry primitives are exploited for the derivation. The agreement with relationships obtained previously under the random uniform isotopic fracture hypothesis demonstrates that the approach is capable of deriving full liberation spectra directly. Both volumetric and superficial composition can be calculated

Jun 21, 1905

By AIME AIME

THE list of deaths during the year 1906 comprises the following names, the figures in parentheses indicating the year in which the persons named were elected to membership Members and Associates.-Arthur Vaughan Abbott (1882), William Anderson Akers (1889), R. Scott Allen (1905), George H. Arlett (1900), Thomas Septimus Austin (1883), Thomas T. Baker (1887), William Tittley Batchelor (1902), Charles Lowthian Bell (1897), Edgar Vallentine Bensusan (1892), George Lothrop Bradley (1874), Ernst Elmer Breisch (1896), Horace F. Brown (1895), James A. Burden (1876), Alexander B. Coxe (1880), George A. Crocker (1879), Albert W. Fiero (1886),

Jul 1, 1907

By D. R. Babich, E. R. Bauer

National Institute for Occupational Safety and Health (NIOSH) researchers are conducting a cross-sectional survey of equipment noise and worker noise exposures in the mining industry. Surface and underground limestone is one commodity recently surveyed. The sound levels of mining and processing equipment were recorded to identify noise sources. Full-shift worker noise exposures were completed to determine the exposure of various occupations. This paper presents the results of the noise research conducted in both underground and surface limestone mines, detailing the equipment likely to cause worker overexposures, and the occupations experiencing overexposures. Implications for worker noise exposure reduction are also reported.

Jan 1, 2006

By J Watt

The Hidden Valley Gold Project is located in a remote and mountainous area of the Morobe Province approximately 30 km south of the township of Bulolo and approximately 90 km south-southwest of the provincial capital, Lae. The Hidden Valley deposit was discovered in 1984 with the nearby Hamata and Kaveroi deposits discovered in 1987 and 1992 respectively. Reserves (Harmony, 2009) at these three deposits are 42.1 million tonnes of ore containing approximately 2.9 million ounces of gold and 45 million ounces of silver. A further 5.4 million ounces of gold and 84 million ounces of silver are in the resources category. The process plant is designed to treat 4.2 million tonnes per year of gold/silver ore extracted by open cut mining methods. Ore is classified into three ore types according to oxidation state: oxide, transition and primary. The silver to gold grade ratio is high for the Hidden Valley and Kaveroi ores, generally in the range 15 - 20:1, and much lower for Hamata, typically 1 - 2:1: Primary ore is the dominant ore type at Hidden Valley with sulfur grades up to about two per cent sulfur. Oxide and transition ores are more prevalent at the Hamata deposit, but its primary ore has up to five per cent sulfur grades. Variable ore types, particularly in the initial years of operation, high silver to gold ratios and limited plant site area, due to the challenging terrain, present the main processing challenges for this project. This paper describes the operating strategies and process development for the main areas of this circuit, highlighting selections of processes and equipment that achieve cost effective, yet flexible solutions to the treatment of ores from these deposits.

Jan 1, 2009

By Axel Doelcken

?? Liebherr excavators in standard configuration are generally designed to operate in an ambient temperature range between -12°C and +55°C (10.4 °F and 131°F). ?? To operate effectively and efficiently in very low temperatures special consideration needs to be given to the design ??An inappropriately designed hydraulic system unable to withstand extreme changes in temperatures or varying working conditions will lead to: - premature wear and more frequent replacement of components - increased maintenance & unplanned downtime This will affect productivity & operating costs.

May 1, 2008

Gold mines produce unique water treatment requirements. This paper focuses on case studies of innovative processes used for treatment of water resulting from gold mining and processing. The case studies include treatment of mine dewatering water for beneficial application from an Australian gold mine, Bendigo Mining, as well as treatment for arsenic removal of tailings water from mining and processing at Goldcorp mines in Canada. Gold mining can often require dewatering to prevent groundwater seeping into and flooding the mine workings. Gold mining and processing often accumulate wastewaters in a tailings dam. The mine water can contain contaminants such as dissolved salts, iron, arsenic, manganese, heavy metals and odorous sulfates. Environmental discharge requirements as well as community needs for water drive mine operators to consider the most appropriate water treatment process. Treatment of gold mine water can require processes including oxidation, pH adjustment, coagulation, flocculation, clarification, further oxidation/adsorption of specific metals such as manganese, filtration, salt reduction utilising reverse osmosis, brine minimisation and other innovative technologies. These processes are discussed through the case studies with examination of the specific treatment process that is required. This paper uses real case studies of gold water treatment processes to explain and examine the technology and the reasons for designing specific processes. The focus is toward explaining innovative processes where the water is used for sustainable environmental discharge or treatment to a quality that can be beneficially used by the local community.

Jan 1, 2007

By R Bertuzzi

This paper presents a three-dimensional analysis of a trapezoidal-shaped segmental tunnel lining for a recent tunnelling project in Sydney. Two- dimensional analyses, hand calculations and equipment selection defined the lining geometry and loads. The analysis, which was undertaken using 3DEC (Itasca), included a complete ring of six segments bolted together to assess the impact of imperfectly built rings. Asymmetry was induced in the analysis by unfavourable positioning of segments within construction tolerances. Model output includes displacement and stress within the entire ring and normal, shear and bending moments at the joints. For the case analysed, the results suggest a 10 mm construction tolerance increases normal and shear stresses along the radial joints by approximately 25 per cent and 15 per cent, respectively and up to a doubling of the induced moments.

Jan 1, 2008

By T. A. Muhlare

"Large quantities of slag are produced every year and dumped on slag heaps around the world, posing a potential environmental threat due to contained heavy metals content. Slags are waste minerals produced during furnace smelting of minerals. The contained values of base metals may be released into the environment under natural weathering conditions polluting ground and underground water. Copper losses into slag are a continuous problem in pyrometallurgical smelting operations. Due to shortage of ore concentrate, various mining operations have initiated the recovery of copper from dumped slag. The typical process uses crushing, milling and flotation. These operations create excessive liner wear rates during crushing and milling because the bond work index of copper slag is 22 kWh/t and this is considered a very hard slag. The process also has reduced flotation recoveries and requires high flotation reagent consumption. The present work shows that digestion of the milled copper slag slurry with concentrated sulphuric acid at a temperature of 250oC forms a solid cake and leaching of the solid cake with water is a possible option. However, the consumption of sulphuric acid can have a considerable cost on the recovery process. This can be limited by producing a leach residue containing gypsum and silicate materials as amorphous silica which are suitable for use as an additive for Portland cement. Laboratory results show that 90% copper recoveries can be achieved. The leaching is conducted to prevent silica gel formation and iron co-extraction. Leaching is optimum if silica gel-free solutions and good filterable residue are obtained. INTRODUCTION Slag is a waste by-product of smelting and converting operations in metallurgical plants. Both smelting and converting operations are aimed at iron separation from base metal sulphides in non-ferrous metallurgy. The iron sulphide component of the ore or concentrate is oxidized to iron oxide at higher temperatures in the molten form, and then fluxed with silica and other oxide rock minerals to produce fayalite (2FeO•SiO2) slag (Schlesinger et al., 2011). Slags are generally deposited on dumps and considered to be unreactive materials. Smelter copper slag contains significant concentrations of several potentially toxic elements, including arsenic, lead, cadmium, barium, zinc and copper. These elements can be released into the environment under natural weathering conditions and cause pollution of soils, surface waters and groundwater (David, 1998)."

Jan 1, 2015

By H. Richard Eisenbeis, Donna M. Watkins

Many technical professionals (tp)* desire to occupy upper level management positions. But career paths for most scientists and engineers do not extend beyond their specific disciplines. This is unfortunate. Our technical frontiers are expanding so rapdily that it is difficult, if not impossible, to make sound top management decisions without understanding the technical complexities involved. Technical professionals often are not considered for upper level management positions because they lack the managerial and interpersonal skills necessary to become successful administrators. You've heard this before, but a key component of these skills is the ability to communicate. Technical professionals are often unable to communicate as well as they should with nontechnical professionals and nonprofessionals within the organizations that employ them. Communication is important for managerial success Communication is the network of interactions whereby knowledge and understanding are conveyed from one social set to another (Flippo and Munsinger, 1982). In order to be successful, managers must not only be "good" communicators, they must be "effective" communicators as well. Good communication occurs when managers are able to formulate and transmit their messages in such a way that they are received and understood. Effective communication goes one step further: It occurs when recipients accept messages as legitimate and respond to these messages in the manner desired. Before promotion into upper level positions, managers must have developed organizational skills (planning, decision making, organizing, and controlling) and interpersonal skills (directing, influencing, and motivating). Applying these skills effectively is difficult without a highly refined ability to communicate. Effective communication, then, is basic to managerial success. Nowhere, perhaps, has the importance of being able to communicate effectively been emphasized more than in Mintzberg's landmark study of managerial roles (Mintzberg, 1973). Mintzberg's results indicate that executives typically averaged 36 written and 16 verbal contacts a day. These contacts were both important and trivial. They generally occurred in a random manner. Time spent on each varied. Scheduled meetings averaged over an hour. Desk work, telephone calls, and unscheduled meetings required an average of 15 minutes or less. Why technical professionals have difficulty communicating Three reasons why technical professionals do not communicate well are: • The work motivational patterns and personal attitudes of technical professionals are not conducive to effective communication. • Students in technical professions are not encouraged by educational institutions to develop their communication skills. • Organizations do not insist that all technical professionals be able to communicate in the language of business. The work motivational patterns of most technical professionals are indicative of internals and high achievers (Hunt, Salisbury, and Whittington, 1968). As internals, they believe they control their own destinies. As high achievers, they believe that task accomplishment is a primary indicator of success. To ensure a task is completed in the manner desired, tp's attempt to structure and define work situations so they alone are responsible for results. TPs consider the task accomplished when they, and perhaps other tp's, are satisfied with the results. From the tp's perspective, the task may have been completed. From a communication standpoint, two other factors may apply. First, solving the problem required very little interaction (and thus, communication) with others. Second, the tp's, considering the task accomplished, have little concern for how their "technical" answers will be translated to nontechnical persons needing

Jan 8, 1987

By D. J. Dollhopf

A week-long selective overburden handling dragline op ration was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to hvdrologically isolate a saline overburden zone during placement in the spoil piles. The saline zone had concentrations considered inimical to successful reclamation and was potentially dangerous to future water quality in the spoils aquifer. The zone was identified after review of chemical data for overburden samples collected from the intense 60 m grid drilling pattern. The saline zone in the overburden was: 1) handled in a normal manner; 2) segregated and buried; and 3) segregated, buried, and covered with a relatively impermeable 1.0 m thick clay cap. The method used to formulate this demonstration, the demonstration itself, and the monitoring and evaluation techniques are described in this report. Observation wells were installed to monitor ground water in the overburden, Rosebud coal, and McKay coal. Data from these wells were, used to estimate post reclamation water levels and to evaluate recharge and water movement characteristics in the vicinity of the demonstrations. The inimical zone was successfully handled in a selective manner with a minimum of delays. Economic analysis indicated cost of these selective burial operations to be about 1.1 to 1.5 times the cost of the normal operation at this particular mine site. Long term monitoring will be required to evaluate the effectiveness of these handling techniques in hydrologically isolating undesirable overburden materials.

Jan 1, 1977

By Isadora Maria Oliveira Anício Costa

Desenvolvimentos recentes no emprego de ligas NiTi superelásticas (SE) na confecção de instrumentos endodônticos rotatórios envolvem a aplicação de tratamentos térmicos nos instrumentos inicialmente produzidos a partir de ligas SE. Neste trabalho foi estudado o efeito de tratamentos térmicos e sua contribuição para a evolução das propriedades funcionais de um fio de NiTi SE. Os fios comerciais de NiTi, aproximadamente equiatômicos, foram ensaiados após o tratamento de recozimento por 1 hora, em temperaturas de 300°C a 500°C, e então temperados em água. A caracterização física do material foi realizada por calorimetria exploratória diferencial e as propriedades mecânicas foram obtidas em ensaios de tração e de recuperação de forma. Os resultados apontaram aumento nas temperaturas de transformação dos fios com o recozimento, o aparecimento da dupla transformação austenita - fase R - martensita B19’ durante o resfriamento. Observou-se também diminuição do módulo de elasticidade aparente e aumento da deformação residual com o aumento da temperatura de recozimento, indicando, em concordância com a variação nas temperaturas de transformação, que o material passou a apresentar o efeito memória de forma.

Aug 8, 2018

By D. W. Cooper

The AMAX of Canada Limited Kitsault mine is located approximately 150 kilometers, by air, north of Prince Rupert, British Columbia at the head end of A1 ice Arm, just east of the southern tip of the Alaskan Panhandle. It is presently only accessible by sea or air, although a road is being constructed by the company which will provide access to Terrace, a commercial centre with a population of about 15,000. The topography is typically coastal mountainous with peaks rising to 2,100 meters around the head end of the inlet. The concentrator is at an elevation of 515 meters with the mine at 630 meters. This open pit molybdenum mine was previously operated between 1968 and 1972 by British Columbia Molybdenum Limited, a subsidiary of Kennecott Copper Corporation. AMAX of Canada Limited has spent $194 million to refurbish and expand this operation.

Jan 1, 1982

By Kermit G. Davis, Sean Gallagher, William S. Marras, Kimberly Kovacs

This study evaluated spinal loads associated with lifting and hanging heavy mining cable in a variety of postures. This electrical cable can weigh up to 10 kg per metre and is often lifted in restricted spaces in underground coal mines. Seven male subjects performed eight cable lifting and hanging tasks, while trunk kinematic data and trunk muscle electromyograms (EMGs) were obtained. The eight tasks were combinations of four postures (standing, stooping kneeling on one knee, or kneeling on both knees) and two levels of cable load (0 N or 100 N load added to the existing cable weight). An EMG-assisted model was used to calculate forces and moments acting on the lumbar spine. A two-way split-plot ANOVA showed that increased load (p<0.05) and changes in lifting posture (p<0.05) independently affected trunk muscle recruitment and spinal loading. The increase in cable load resulted in higher EMG activity of all trunk muscles and increased axial and lateral bending moments on the spine (p < 0.05). Changes in posture caused more selective adjustments in muscle recruitment and affected the sagittal plane moment (p < 0.05). Despite the more selective nature of trunk EMG changes due to posture, the magnitude of changes in spinal loading was often quite dramatic. However, average compression values exceeded 3400 N for all cable lifting tasks.