Search Documents

By G. W. Jones

"INTRODUCTION As part of its work in promoting safety, the Bureau of Mines is investigating various means of eliminating or mitigating the explosion hazards of combustible gases encountered in mining and industry. Information has been obtained and a procedure developed whereby the explosibility of many complex gaseous mixtures may be calculated in a rather simple manner without the necessity of performing laborious laboratory experiments. An earlier publication 3/ described the method of determining by calculation the limits of inflammability of gaseous mixtures, including methane, hydrogen, carbon monoxide, nitrogen, carbon dioxide, and oxygen. The information published in the above report permitted calculation of the limits of inflamnability of such gases as are liberated by mine fires, gases from explosives, automobile exhaust gases, gases present after mine explosions, blast-furnace gas, and other gases of similar type.Gases liberated in certain potash mines in the western part of the United States sometimes contain ethane, in addition to the gases named. An investigation was made to obtain data from which the limits of inflammability of such gaseous mixtures could be determined by calculation. 4/Similar data have been Published covering all types of natural gases containing wide ranges of concentration of nitrogen and carbon dioxide.5/"

Dec 1, 1944

By M. A. Kessick

Current treatment and disposal procedures are compared for clay slimes resulting from the extraction of Alberta oil sands, the extraction of Florida phosphate matrix, the recovery of diamonds from kimberlite deposits in South Africa, the recovery of kaolin from clay deposits in southwest England and the upgrading of bauxite ore. Published research in the area is reviewed, and common trends which are emerging in the disposal of clay slimes are discussed.

Jan 1, 1978

By R. H. Sprute

The Federal Bureau of Mines conducted full-scale field tests in electro-kinetic dewatering and consolidation of slimes in cooperation with the Hecla Mining Co. at two of the firm's underground mines in north Idaho. To test the technique on new deposits, 4,000 ft3 of slimes from a collection sump, pumped into a watertight stope equipped with electrodes, were treated in two steps. Immediately after placement, direct current was applied using a floating electrode to hasten settlement of suspended fine particles. After removal of clarified water, the residue was further dewatered and hardened with electrokinetic treatment. In 25 hours, the material had become firm and dense with a surface capable of supporting workmen. In testing old deposits, 10,000 ft3 of slimes, placed in an unused tail drift 10 to 12 months previously, were treated. This material was sufficiently consolidated by electrokinetics to allow its removal from the mine with standard ore-handling equipment. In both tests, electrokinetic treatment densified slimes in a relatively short time with moderate power consumption.

Jan 1, 1976

By Sunfangze Liu, Xumeng Chen, Yongjun Peng

Efficient separation of naturally hydrophobic gangue, such as talc and carbonaceous materials, from sulphide minerals in flotation is becoming a significant challenge in many processing plants due to the need to process lower grade and more complex ores. Considering the hydrophobic nature of these gangue minerals, prefloating them at the beginning of the flotation circuit in the absence of collectors and rejecting the concentrate is a common practice to remove these gangue minerals. However, sulphide minerals, such as chalcopyrite, can become naturally floatable due to surface oxidation and therefore may float together with naturally hydrophobic gangue. In this study, a new approach was developed to maximize the prefloat of hydrophobic gangue while minimizing the loss of sulphide minerals. The new approach introduced a prefloat cleaner stage where sulphide minerals recovered to the prefloat concentrate was depressed and separated from other hydrophobic gangue minerals at a low pulp potential with the prefloat cleaner tailing fed back to the main sulphide flotation circuit. Flotation tests were conducted using chalcopyrite and organic carbon. The results show that the proposed approach can significantly reduce the loss of valuable minerals in the prefloat flotation without affecting the reject of naturally hydrophobic gangue. Applying pulp potential control at the prefloat cleaner flotation stage also reduces the consumption of reducing agents while minimizing the effect of reducing agents on downstream rougher flotation.

Nov 23, 2020

Cyanide is reactive to copper minerals and is not suitable to extract the gold from the copper bearing ores. Ammoniacal thiosulfate is considered an excellent alternative lixiviant for leaching copper bearing gold ores. Unfortunately the results of high reagent consumption and poor gold ex-traction were found by thiosulfate leaching of synthetic gold ores containing chalcopyrite, chalcocite or bornite and a mild refractory copper-bearing sulfidic gold ore. In this investigation, several processes have been applied to reduce the impacts of these minerals on gold leaching. The process included: the pre-oxidation of copper sulphide minerals in water or ammonia solution, the reduction of dissolved oxygen in the lixiviant (0.3 ppm DO or 0.7% oxygen), adding phosphate anion in the leach or pre-leach stage, and the addition of a strong copper ligand (e.g., EDA and DETA). The results indicated that the gold extraction could be improved to 93% with the thiosulfate consumption being reduced to less than 8 kg/t. The dissolution of copper minerals was found to be the major reason for increased consumption of thiosulfate and the highly reductive leached surfaces are responsible for the reduced gold extractions.

Jan 1, 2014

By R Peden

Recent, detailed mapping, (Allibone, 1986; Peden, in prep.) of north west Stewart Island, has shown that the Rakeahua Granite (Watters et al, 1968), is comprised of a wide range of granitoid bodies ranging from diorite to leucogranite. As a result of the wide variation in granitoids Allibone (1986), suggests renaming of the Rakeahua Granite to the Rakeahua Granitoid Complex. Names were also proposed for the individual granitoid bodies mapped.

Jan 1, 1987

By E. Matinde

Human beings have been dependent on metals and alloys for livelihoods since time immemorial. In fact, there is irrefutable evidence that successful ancient civilizations achieved supremacy over their environments through the mastery of metals and alloys (Miller, 1995; Mtetwa, 2022). Over time, metals and alloys have evolved to become ubiquitous engineering materials indispensable to mankind, with applications in industrial and residential infrastructure, agriculture, energy generation and storage, transportation and communication systems, and manufacturing, among others (Elshkaki et al., 2018; Watari et al., 2021). Population growth, technological developments, and increase in urbanization and industrialization are all intricately linked to the intensity of use of metals and alloys. With up to 5 billion people estimated to live in urban areas by 2030 (Armstrong, 2009), the demand for metals and alloys will inevitably increase in order to satisfy the increased demand for infrastructure, machinery, and other human needs (Elshkaki et al., 2018; Watari et al., 2021). According to LePan (2022), urbanization and growth of mega-cities will increase the demand for metals and alloys, such as nickel, steel, aluminium, and copper by 116%, 50%, 57%, and 26%, respectively, between 2019 and 2035. Naturally, the production of metals and alloys from natural ores, secondary resources, and/or a combination of both, to meet this increased demand will invariably lead to the increase in generation of deleterious emissions in the form of wastes. In fact, mining and metallurgical wastes currently constitute the world’s largest anthropogenic streams by mass, often containing a high concentration of elements and compounds that can cause potential damage to natural ecosystems and humans (Hudson-Edwards et al., 2011; Lottermoser, 2011; Matinde et al., 2018; Seetharaman et al., 2022). Obviously, society’s heavy reliance on new mineral resources to drive the emerging energy transition entails that the legacy of these waste streams will continue unabated for the near-foreseeable future. The scarcity of high-grade mineral reserves, coupled with deliberate efforts to solve the anthropogenic circularity conundrum, therefore introduces a high level of urgency in the metal extraction industry to develop nascent and more eco-friendly processes and technologies. Integrating circular economy principles based on intentional configurations of circular industrial ecosystems in order to maintain the value of materials and resources in the economy for as long as possible is widely accepted as a practical approach to mitigating the negative externalities imposed by

Sep 1, 2024

By W. T. Wertman

LABORATORY research has been started at the Bureau of Mines Morgantown Petroleum Research Laboratory, Morgantown, Va., to investigate the possibilities thermal-recovery methods for producing crude oils of high API gravity found in oil reservoirs of the eastern United States. This bibliography on thermal methods of oil recovery was compiled as a part of the work. Crude oil discoveries to December 31, 1958, in the United States were estimated to exceed 270 billion barrels. Cumulative production of crude oil through 19.55 was about 60 billion barrels, and the American Petroleum Institute estimates that an additional 30.5 billion barrels are economically recoverable by present methods. On this basis, about two-thirds of the oil that has already been found can be classified as economically unrecoverable for lack of a satisfactory method. The rap icily rising costs of proving new deposit; of domestic petroleum, the lack of new discoveries of large oilfields in the united States, and I he growing demand for crude oil have caused an acceleration of research to develop new or improved methods fur producing "unrecoverable" oil in known reservoirs.

Jan 1, 1960

Comparative tests of four coals used industrially for coke production have been made by three laboratories of the Federal Bureau of Mines, each using its standard equipment and procedures for evaluating coal for coking. Two of the coals were blends used in the western and eastern sections of the United States, the third was a strongly coking coal widely used for producing coke in Alabama, and the fourth was a blend typical of those used for producing foundry coke in the Birmingham district. The coals used and the cokes produced from them covered a wide range of chemical and physical properties. The tests used at all three laboratories for determining the physical properties of the cokes were made according to ASTM (American Society for Testing Materials) methods. The excellent agreement found for the physical properties of the cokes indicated that, for the coals tested, the BM-AGA (Bureau of Mines-American Gas Association) 18-inch circular retort used at Pittsburgh, Pa" the 14-inch slot-type oven used at Denver, Colo., and the 17-inch slot-type oven used at Tuscaloosa, Ala., were substantially equivalent for evaluating coals for production of coke. Thus, added value is given to data obtained previously and independently at these three Bureau laboratories. INTRODUCTION Laboratory equipment to produce coke for evaluation has not been standardized by the industry. The results obtained with anyone design of equipment have been regarded as showing only the relative values of coal to produce coke of the requisite quality. Few systematic studies have been made to correlate results obtained in different types of equipment. Results of one, in which the Bureau of Mines participated, were published recently.2/ This

Jan 1, 1961

By Steven Norris, William Moler, Michael Cole, Patrick Doig, Debi Lewis, Craig Pyle, Matthew Crow

The recently completed Lower Northwest Interceptor Program (LNWI) in Sacramento, California comprises, ten pairs of micro tunnels totaling 4,369 m (14,417 ft),three horizontal directionally drilled bores totaling 956 m (3,154 ft), and two large diameter tunnels under the Sacramento River totaling 1,198 m (3,953 ft). This paper briefly summarizes surface and subsurface conditions, and planning and design considerations. It then goes on to describe problems encounterd with each trenchless crossing, as well as lessons learned with respect to shaft construction, ground control at shafts during tunnel break-in and break-out, frac-out and heave, settlement, obstructions, coordination with permitting agencies, and application of geotechnical baseline reports.

Jan 1, 2007

By Laurance A. Beck

Safety is the most important aspect of haul road design. Although other aspects of road installation enter decisions on design, the safety of persons using the road has to be foremost for the duration of haul road usage. Other aspects of mad design focus on minimizing truck cycle time and fitting haul roads to the long-term configuration of the mine/quarry or construction project. Roads are often installed at high gradients for a short-term goal, but the long-term benefits are easily shown with lower gradient haul roads which provide better cycle times and lower operating costs.

Jan 1, 1995

By Charles Prasky

This report describes and appraises recent progress in the development of a differential sulfatizing process for recovering a ferrograde manganese oxide from low-grade manganiferous ferruginous materials in the Cuyuna range. Individual process steps were carried out successfully using a 20-inch-diameter shaft for continuous countercurrent sulfatization of the manganese, a multiple-compartment rotary drum for leaching the water-soluble manganese sulfate, a submerged-combustion evaporator for the recovery of monohydrate crystals of manganese sulfate, and a shaft furnace for the thermal decomposition of sulfate crystals for production of a ferrograde manganese oxide and a sulfur dioxide gas suitable for sulfatization of fresh are. Of the two general kinds of Cuyuna manganiferous materials--the carbonate slates and the oxidized ores--only the slates were studied at pilot scale.

Jan 1, 1963

By Ismet Canbulat

"In order to ensure the stability of roadways, Anglo American Metallurgical Coal (AAMC) has developed a roof support design methodology that integrates analytical, numerical and empirical modelling. This methodology currently is based on a deterministic approach (a single factor of safety against failure is calculated). However, an improved methodology, based on stochastic modelling technique, has also been developed and currently being evaluated. The main advantage of this methodology is that the design is based on the probability distributions of input parameters; thus the outcome is based on a distribution of factors of safety rather than a single factor of safety. An evaluation of factors of safety may also be used to determine the likelihood of failure, which in turn may be utilized to quantitatively determine and evaluate the associated risks in decision making process. This methodology has been evaluated at Grasstree and Moranbah North Coal Mines in the designs of roof support in various critical areas and has been proven to be successful and a better way of determining the roof support requirements.This paper demonstrates the application of this methodology in a design of an install road roof support at Moranbah North Mine, where the 1,750 tonne capacity ''world's highest rated longwall"" has recently been installed.INTRODUCTIONAnglo American Metallurgical Coal Australia (AAMC) operates three longwall (LW) mines located in Central Queensland. There is an increasing emphasis on the reliability at these operations, as the longwalls are getting deeper and facing more geologically challenging conditions. In addition, the Anglo American Vision is to achieve ""Zero Harm"" through the effective management of safety at all businesses and operations. In order to accomplish this vision, AAMC has developed a proactive ground control management system for a safe and efficient production of underground reserves.Proactive ground control management involves understanding the impacts of the geotechnical environment on likely ground behavior, and it consists of approximately 15 major elements. One of the most essential fundamentals of proactive ground control management is to utilize a roof support design methodology that considers different failure mechanisms and also takes into account all important elements. The design methodology becomes even more important when the area in question is a critical area, which is defined as a high risk roadway where any failure may cause increased levels of safety and financial risks to underground workforce and operations."

Jan 1, 2010

By A. S. Swanson

In view of the necessity or increasing production of metallurgical fluorspar to satisfy wartime demands, 0, M. Bishop, former district engineer of the Bureau of Mines, L. W. Carrier and. J. S. Williams, senior geologist of the Federal Geological Survey, and E. H. Dawson, mining engineer of the War Production Board made a joint survey of the Illinois-Kentucky fluorite district in July 1942 to determine what steps should be taken to increase production. As part of their recommendations, a program for exploring the idle Klondike mine in Livingston County, Ky., was outlined. All the ore produced at the Klondike mine was mined above the 325-foot level, where some tonnage remains. Factors that influenced selection of the Klondike mine for exploration were favorable geological conditions, the state of mine development and the availability of pumping equipment and some usable mine and mill equipment. In December 1942, the Metals Reserve Co. leased the Klondike mine from the Salem Fluorspar Co.

Jan 1, 1949

Comparative Studies on Balls Versus Spheroidal Tetrahedrons Working Media to Ore Grinding in an Industrial Drum Mill

Sep 13, 2010

By S Döpp

Commencing with early experiences in iron ore beneficiation made at Beeshoek Mine, the paper follows through the process of extensive mineralogical and metallurgical investigations carried out during feasibility study. The paper will discuss the design process and logic followed over the last years, the challenges and decisions the design team faced in order to draw the conclusions that ultimately resulted in today’s value add approach at Assmang’s Khumani Operations.As integral part of the benefi ciation concept, a focus is set on the jigs, explaining the plant concepts, planned expansions and their contribution to the overall value add approach at the mine.The case study is intended to describe the outcomes of the design versus the actual achieved and the further value add projects to be implemented. As for future prospect, the incorporation of Wet High Intensity Magnetic Separation (WHIMS) demonstrates Assmang Khumani’s pursuit to maximise productivity and overall recovery.DMS was evaluated as an alternative to jigging within a comparative test work study, but in conclusion the option had to be excluded due to its inability to achieve the high density cut point required to achieve the sales specifi cations. In contrast, the investigation on producing an additional middlings fraction on the lumpy ore jigs prove to be an adequate option for further improvements of overall mass yield. With further liberation, a saleable product will be achieved by secondary beneficiation on Fines Jigs and WHIMS.Concluding, jigs are considered the most viable and cost effective benefi ciation process for off-grade ore +0.8 - 32 mm at Beeshoek as well as at Khumani, while WHIMS is the process under consideration for super fines recovery.

Jul 11, 2011

By C. L. Popp

The scope is to address issues confronted by parties in the mining industry such as: Mine planners, survey and engineering departments, field teams and subcontractors. Describing approaches and best practices for assembling a project team to identify and create modeling requirements and to implement beneficial results. 3D Machine Control and Guidance tools continue to reduce project risk and attract quality resources with skill sets new to the earthmoving industry. These tools increase production, reduce rework and help with government permitting.

May 1, 2013

By John B. Goodman

A LOW-TEMPERATURE carbonization assay test is described, and factual data derived from this test are presented. The test procedure outlined in this report incorporates a mild-steel retort of improved design, an accurately controlled method of heating, and a complete collection and condensation system for the solid, liquid, and gaseous products of carbonization. The test described establishes, under closely controlled conditions, the relationship of temperature to yields of products on carbonization. Noncoking or weakly coking coals and other carbonaceous material are particularly amenable to testing by the assay. Mass balances of 100 percent± 0.3 are obtainable by this test. It is believed that the efficiency of the test and the accuracy of the type data obtained have been materially increased.

Jan 1, 1953

By M. J. Ferrante

A process was investigated for preparing Specification-grade nickel (containing less than 1 percent cobalt) by stripping it electrolytically from a nickel sulfate-boric acid solution and using the stripped electrolyte for the preferential dissolution of nickel from basic carbonates of nickel and cobalt. The basic carbonates were produced at the plant at Nicaro, Cuba, owned by the U.S. Government. Determination of the optimum conditions for deposition of Specification-grade nickel indicated that the upper limit of cobalt concentration was 0.1 gram per liter. The pH, temperature, and concentrations of nickel and boric acid in the electrolyte were not critical. An aluminum cathode and two lead anodes were used at a cathode current density of 1.2 amperes per square decimeter.

Jan 1, 1959

By James C. Duchon

The use of extended workdays (regular shift lengths of 10 or 12 h (hour), while still maintaining a 4O-h workweek) in mining operations is attracting growing interest in the United States. There is very little doubt that extended workdays is a very popular alternative among the work force because of the significant increase in days off, including weekends, especially when compared with traditional rotation schedules of working seven straight shifts or having only one weekend off every 4 to 6 weeks. However, there are some serious concerns by management, workers, unions, and various governmental policymakers that working 10-or 12-h days may create an added risk of accidents and health problems. The U.S. Bureau of Mines reviewed the literature studies related to the safety and performance issues of extended workdays. This report presents a summary of those findings. The studies examined in this review are divided into three sections: (1) laboratory, (2) field, and (3) accident and injury analysis. In general, results are inconclusive. Studies have shown both positive and negative effects. It is concluded, therefore, that in industries such as mining where accidents are a serious concern, special measures and evaluation in the use of extended workdays be considered.

Jan 1, 1994