Search Documents

By P. A. Hendricks

This U.S. Bureau of Mines (USBM) report identifies and evaluates factors responsible for metal/nonmetal (M/NM) underground mining accidents involving mobile equipment. Information regarding the occurrence and severity of the accidents, the type of equipment involved, the primary and contributing causes, and preventive measures is included. The goal of this report is to provide information that will aid mine operators and safety managers in the recognition of hazards associated with operating mobile mining equipment in an underground mining environment.

Jan 1, 1994

By S. C. Termes

To help develop the basis for new fine-particle separation methods, the Bureau of Mines has investigated the use of cross-linked starches containing four chelating groups--carboxylate, iminodiacetate, dietha-nolamine, and xanthate--as flocculants for selected metal oxide and hydroxide mineral fines. It was found that those starches capable of interacting with the mineral surface by a chemisorpti,on mechanism (as indicated by zeta potential measurements) produced the highest recover-ies and'grades of the metal oxide or hydroxide when flocculated from a binary mixture with quartz. The effects of pH, dispersing agent, stirring rate, stirring time, and starch dosage on selective flocculation were studied for binary mixtures of hematite and chromite with quartz. Floc strength becomes important in achieving maximum recoveries by mechanical postflocculation separations.

Jan 1, 1985

By Edward W. Parsons

The transverse force developed by expansion-shell rock-bolt anchors on the wall of a drill hole as the bolt is tensioned was measured by the Bureau of Mines using a device specially designed and fabricated for attachment to a universal testing machine. Load cells equipped with electrical-resistance strain gages provided the data from which the transverse force, in pounds, was calculated. Seven different expansion-shell anchors were tested, and the ratio of transverse force to bolt-tension load was found to range between 0.98 and 1.94 to 1.0. The drag load appeared to be the major cause of the transverse-force variation, but the relative effects of individual factors that affected the ratio between the transverse force and the bolt tension were not determined.

Jan 1, 1968

By A. B. Hooker

Gassy mines require daily inspections with methane detectors to test for the presence of methane. Although in many manes it may be sufficient to know that there is no methane present or that its percentage is below a certain amount, it is desirable and often necessary to determine definitely the percentage of methane at the working faces and in the various air currents. The Bureau of Mines recognizes two general types of portable methane detectors, namely; 1. Methane detectors by which the presence of methane may be detected and its approximate percentage estimated.

Jan 1, 1929

By José Alberto da Cruz Junior

Aços multiconstituídos têm aplicações voltadas principalmente para o setor automobilístico. Isso porque esses apresentam uma boa combinação de elevada resistência, ductilidade e tenacidade. A elevada resistência desses aços é devida a martensita e aos finos feixes de ferrita bainítica, enquanto que a tenacidade e a ductilidade são atribuídas aos filmes finos de austenita retida presentes entre os feixes. Esses filmes contém uma maior concentração de carbono em relação aos blocos de austenita retida. Uma consequência é que estes se tornam mais estáveis mecanicamente e termicamente. Dessa forma, foi realizada a avaliação do desempenho mecânico de um aço tratado isotermicamente abaixo de Mi e revenidos a 400°C/1 h. Os resultados dos ensaios de impacto mostraram que quanto maior a fração volumétrica da austenita retida maior é a energia absorvida, independente da morfologia desse constituinte.

Aug 7, 2018

By C V. B Cunningham

The assessment of blasting results under production conditions is extremely difficult. As a result, it can take months or years to establish objective and valid estimates of explosive performance in achieving rockbreaking goals. This fundamental problem often results in decisions related to the manufacture, marketing, purchase and use of explosives being largely swayed by calculated energies from detonation codes. However, these codes are by no means standardised. Different energies are given by different codes because these employ varying combinations of fundamental science and empiricism. After a basic review of code operation, important guidelines to dependability are given with reference to ICI’S state-of-the-art codes IDEX and CPEX. Distinctions are drawn between Ideal, Non-Ideal and Blasting Codes. Concepts of explosive energy are discussed in brief.

Jan 1, 1991

By J Coward, S Bulatovic

There are currently two operators producing oil from the surface-mineable portions of AlbertaÆs oil sands (Syncrude Canada Ltd and Suncor Inc) and two other companies are proposing to enter the industry (Albian Sands Energy Inc in 2002 and True North Energy LP in 2004). Tailings from the two current oil sands plants contain approximately 220 000 tonnes per year of TiO2 and approximately 80 000 tonnes per year of zircon. This represents approximately six per cent of the worldÆs TiO2 consumption and approximately nine per cent of the worldÆs zircon production. With the commissioning of plants by Albian and True North, and the announced expansion of plants by Syncrude and Suncor, it is expected that these tonnages could quadruple in the next ten years. All of these operators have at least 50 years of reserves even at these expanded production rates. The occurrence of heavy minerals in AlbertaÆs oil sands has long been known and is well documented in the literature. There have been a number of attempts to produce market-grade products from this resource and the results of this work have been quite mixed. Typically, researchers have used the normal mineral dressing techniques of the industry and have found the mineral assemblage does not respond to these techniques all that well. This has led to the widely-held suspicion that there must be some difficult metallurgical problems associated with this resource. There are three main problem areas that have created difficulties for previous researchers:the bitumen coating on the sand grains; secondary mineralisation such as pyrite, siderite and calcite; and a high proportion of aluminosilicates (approximately 25 per cent) that have the same gravity, electrostatic and magnetic properties as other minerals in the heavy mineral suite. Recent work by Lakefield Research shows that these problems can be largely overcome with some novel approaches. The bitumen can be removed by washing with a solvent in the presence of a demulsifier; the pyrite can be removed by flotation; and the titanium and zircon minerals can be separated by selective flotation followed by conventional electrostatic and magnetic separation.

Jan 1, 2001

By T. B. Linde

The Morenci In-pit Crusher and Conveyor System has been designed with safe production and cost savings in mind. Large open pit mines around the world have been installing semi-mobile crushers and linking them with a pit conveyor system to lower unit cost. At Morenci two 60/89 in. gyratory crushers are incorporated into the semi-mobile crushing plants. The ore is reduced to -8 in. and transported out of the mine on a 60 in. steel cable belt. This paper includes an overview of the Morenci In-pit Crusher and Conveyor System from the drawing board to open pit installation and finally a discussion on operating and repair considerations.

Jan 1, 1990

By Robert Hopler

This article, advocating having employees whose specific job would be to fire blasts in underground coal mines in llinois, was written 5 years prior to the establishment of the U.S. Bureau of Mines, and 2 1/2 years before the worst month in U.S. coal mining history, when 692 miners were killed in three separate explosions in December 1907. Obviously something had to be done to improve safety in the use of explosives, and having dedicated shotfirers was a good first step.

Jan 1, 2006

Jan 1, 1967

By C. K. Kocsis, S. Hardcastle

Mine ventilation, requires electricity to operate the fans and fossil fuel for heating. Typically, this accounts for approximately 40% of the overall underground energy consumption. This is considerable, and one of the major causes of this expense is that most mine ventilation systems are designed for the "worst-case-scenario" with respect to ventilation demand, which is commonly dictated by diesel equipment usage. Once designed, mines tend to operate their ventilation system at this peak level despite their exceeding day-to-day development and production needs due to lack of appropriate ventilation controls. In underground metal mines, TeleminingTM, which includes the tele-remote operation of mobile development and production equipment from surface, will change the mine design criteria including its support infrastructure such as the ventilation system. With the removal of machine operators to surface control rooms, conventional ventilation systems designed to dilute and remove pollutants can become redundant. Depending on the ultimate need for ventilation, its cost in automated mines with tele-remote equipment operated from surface will be lower than the cost of ventilation in conventional mines. These cost savings, which could be significant, would not only come from the ability to reduce the amount of ventilation in the mine, but also through the capacity to automate its distribution. This paper provides an indication of the new airflow requirements in stopes and dead-end developments for the tele-remote and automated mining processes based on climatic modelling. Furthermore, this paper makes a cost benefit analysis by comparing the ventilation system operating cost of a conventional underground metal mine based on the mobile diesel powered equipment design criteria with the newly redesigned ventilation system operating cost of an automated mine based on the "heat management" design criteria.

Jan 1, 2002

By Tom Tallone

In the majority of metal and nonmetal mining operations, narrow vein deposits are being mined with slusher hoists. Thin; method of mucking is costly, due in part to its inherent labor intense operation and to its inability to muck 100 pct of the deposits. Mechanized equipment would greatly improve the material handling in narrow vein mining and would dramatically reduce the operational cost. The Compact Loader/Trammer, known as the "mini-mucker" has been developed to increase productivity of the load/haul/dump portion of the typical narrow vein mining cycle. This is Volume II of the final report and concerns the operation and maintenance of the mini-mucker. Volume I covers a general and design review of the activities on the subject contract and are available under separate cover.

Jan 1, 1985

By Mandius C. Lundal

This report describes the work done to develop a coal mining machine to increase productivity and recovery from thin seams beyond the highwall, in addition to decreasing the miner's susceptibility to to highwall hazards. First, radar transducers were adapted to measure coal thinkness and detect rock and coal interfaces; Then, the radar was incorporated into a cutterhead with steering controls. Next, visual displays were designed to show cutter position in the coal seam, and anticipated change In coal seam inclination. Finally, development of a telemetry system made remote control of the cutterhead possible. Simultaneously, a high-performance extended depth (HPxD) auger machine was designed with an automatic system to handle 600 ft of 36-in. diameter dual spiral flight conveyor sections. A two man crew controls all operations from a weather conditioned cab outside the VDZ, either at night or day time. As a primary mining tool, working 4000 hr/yr (2 shifts/day) recovering 60% of the coal 600 ft beyond the highwall, production to 500,000 ton/yr can be achieved. Volume II contains technical discussion of subsystems and machine drawings.

Jan 1, 1977

By J. Gummer, M. Williams, S. J. Hawksworth

A common problem encountered in British coal mines is bearing failure on conveyor system idler rollers, which on occasions has led to fires. The UK Mines Inspectorate initiated a study of such failures to assess the potential for ignition of explosive atmospheres. As part of this study HSL have developed a system to measure the temperatures generated within the bearings during controlled failure. Temperatures are measured using both infrared thermal imaging and contact thermometry. The work to date has shown that temperatures well in excess of the auto-ignition temperature of methane can occur.

Jan 1, 2003

By W. K. Connor, O&apos

Thermal Treatment Technology Division Albany Research Center, U.S. Dept. of Energy Oregon. This evaluation included a characterization study and direct smelting tests conducted in a bench-scale electric arc furnace (EAF). In contrast to other thermal treatment technologies considered for these wastes (i.e., fluidized bed combustion), direct smelting in the EAF can process 100% of the wastes without prior beneficiation, and utilizes solid oxidant additions (in this case iron ore) rather than air to oxidize the carbon. This solid oxidant addition is advantageous because it results in the production of several value-added furnace products. These products include cast iron resulting from the reduction of the iron oxides, baghouse dust containing virtually all of the zinc from the residues, and a clean (nonhazardous) slag product suitable for recycle as concrete aggregate or construction fill. Offgas from the smelting furnace also holds potential as fuel gas for cogeneration. The direct smelting tests conducted thus far were successful at producing the desired furnace products, exhibiting the potential for complete recycle of the waste pile. A cast iron product of comparable quality to conventional cast irons was produced, at nearly 80% iron recovery to the metal. The slag product was determined to be nonhazardous, based on the EPA TCLP. Lead and zinc partitioning to the dust product was greater than 99%. The material balance over the furnace indicates that for every ton of feed processed, 540 lb. of cast iron, 600 lb. of slag, and 150 lb. of dust would be produced. Energy consumption was roughly 1.10 kWxh/lb of feed material. Prior experience suggests that these figures measured in the bench-scale furnace would translate to 0040 to 0.50 kWxh/lb at the industrial-scale.

Jan 1, 2000

By Garry Keizer

The Cortez gold mine is located in Lander County, NR, about 130 km (80 miles) southwest of Elko. Cortez Gold Mines (CGM) is a joint venture between Placer Dome US Inc. (60% operator) and Kennecott Corp. (40%). The claims that supply oxide and refractory ore feed to the Cortez milling facility are located in both Lander and Eureka counties. These include the Cortez and Horse Canyon deposits, all operated by the joint venture. Other deposits outside the CGM claim area include Fire Creek, Buckhorn, Gold Bar and Tonkin Springs. These deposits all occur along the Battle Mountain-Eureka Trend. History Mining in the Cortez district began in 1862 with the discovery of high-grade silver ores. Grades in the hundreds of ounces per ton occurred in an area 7 km (4.5 miles) southeast of the current CGM mill site. Underground mining through the Garrison and Arctic tunnels provided the bulk of the ore production between 1864 and 1895. To a lesser extent, the Mill Canyon area also supplied ore until 1930.

Jan 1, 1993

By G Capes, L Morizzi, N Mitkas, E Jones, D Grant

This paper describes the mining setting for the sub-level open stoping (SLOS) mining method used at Olympic Dam (OD), and investigates the range of stope performance conditions encountered over 30 years of production, using a qualitative description of the factors influencing performance. Utilising a continuous improvement tool, the Plan-Do-Check-Act (PDCA) process, and a forward-looking rock mechanics program, the intent is to identify the key factors driving productivity and performance to create a stable and achievable long term mine plan.

Mar 15, 2021

By Murad Y. Abu-Farsakh

This paper presents the analyses of load-transfer (t-z) behavior of twelve prestressed concrete (PSC) instrumented test piles that were driven in different locations of Louisiana. The load transfer method is an efficient and practical tool for the analysis of single driven pile to predict the ultimate load. The test piles were instrumented with vibrating wire strain gauges in order to calculate the shear transfer for different soil layers during the static load test. The static load test was performed on all the test piles after 10 to 14 days of end of driving. Empirical load-transfer models were proposed previously by different researchers (Fleming 1992, Hirayama 1990, Krasinski 2012, Bohn et al. 2017) after analyzing the instrumented test pile results. For this study, load transfer of each soil layer was measured and compared with the previously developed existing model. The stiffness parameter (M) for the hyperbolic equation was calibrated in order to best match the measurements. The good agreement of the proposed curves was then confirmed by applying them to assess the overall load-settlement curve of other pile load test results available in the literature. INTRODUCTION The load transfer mechanism (stress-strain relationship) for an axially loaded pile usually comprises of three loading mechanisms: axial deformation in the pile (z), soil skin friction along the shaft (qs), and soil end-bearing (qb). The development of soil skin friction with axial deformation is referred as the t-z curve, and the development of soil end-bearing with axial deformation is referred as the q-z curve. Figure 1 presents the load transfer mechanisms in an axially loaded pile and the corresponding spring mass models for t-z and q-z curves (API, 2002). In order to construct the load transfer curve in clay under vertical load, the axial load transfer (t-z) curve and end-bearing load transfer (q-z) for that particular soil should be assessed separately. The axial load transfer (t-z) method is probably the most widely used technique to study the problem of single axially loaded piles. Therefore, the load transfer through the shaft of the pile and are getting more and more important compared to the only the pile capacity analyses. The load transferred from shaft to the surrounding clay soil is a function of the width of the pile and the surface roughness of the pile and clay properties. The development of a representative procedure allows the assessment of the t-z curve in soil (sand and/or clay) that leads to the prediction of a nonlinear vertical load-settlement response at the pile head.

Jan 1, 2018

A computer system for calculating the illumination on coal mine surfaces due to machine-mounted lights is described. Utilizing numerical models of mining machinery and measured data on luminaire output characteristics, the program computes the ft-candle levels incident on the mine entry surfaces for any desired machine/luminaire/ entry configuration. Shadowing effects of the machine are taken into account. Results are provided at 2 ft. intervals on the face, left and right walls, floor and roof. The system operates, interactively from a Tektronix 4014 graphics terminal which handles all input/output functions. The software is installed on a Cyber 74 computer that communicates with the terminal via telephone line.

Jan 1, 1978

The MineSight Schedule Optimizer (MSSO) is a new production scheduling tool developed by Mintec, Inc. using mixed integer linear programming (MILP) techniques. This tool was developed to solve the short- and medium-term schedule problems for surface and underground mining operations that involve multiple mining areas, multiple processes, multiple destinations and blending requirements. MSSO finds the optimum schedule in each period that achieves the objective while satisfying comprehensive product quality and quantity requirements as well as physical and technical constraints. Using the MineSight Planning Database (MSPD) as a central data hub, MSSO seamlessly works with MineSight 3-D (MS3D) block models and third-party data, MineSight Interactive Planner (MSIP), MineSight Haulage (MSHaulage) and MineSight Activity Planner (MSAP) to prepare data, formulate MILP models, calculate, report, fine-tune, save and visualize schedules. This paper presents the features and capabilities of MSSO. A case study is also given to demonstrate the applications of this new tool.

Jan 1, 2009