Search Documents

By W. Missildine, J. K. Hrica, I. Benbourenane, T. J. Orr, J. L. Bellanca

Each year, haul truck accidents account for a large portion of mining injuries and fatalities. To better understand why these accidents continue to occur, researchers from the National Institute for Occupational Safety and Health (NIOSH) utilized a cognitive task analysis methodology to identify the user requirements of surface haul truck operators and assess differences in perceptions between operators, managers, health and safety professionals, trainers, and maintenance personnel. Additionally, researchers used the critical decision method to focus on better understanding the cognitive demands, decision-making, and problem solving during nonroutine incidents. The preliminary results of this study identify and explore themes within the broad categories of hazards, skills & expertise, and training and provide detailed accounts of nonroutine incidents such as near-misses, loss of control, and collisions. These accounts reveal insights into operator decision making and event progressions that can then be used to build more realistic training scenarios and address hidden hazards and root causes of these incidents. These results, along with potential solutions offered by study participants, can inform future research and help identify creative interventions that can be used by mine operators to address haul truck safety issues

Mar 2, 2022

By Norman A. Jull

"IntroductionThe scope of this paper is intended to deal mainly with cyclones in grinding circuits. However, the section on Cyclone Equipment, contains more general descriptions, to cover most of the cyclones used in mineral separation plants.Cyclones as heavy media separation vessels are discussed by Mark Freberg (this volume). Their use in tailings deslirning is discussed by P.C. Lighthall, eta/. (this volume).Cyclone EquipmentCyclone TerminologyApexObviously, the apex of a cone is the smallest end. However, with cyclones the term is usually used for the fitting which is attached there to control discharge of the underflow stream.Note that the cyclone need not be so mounted that the apex is the lowest point, although that is the most common method. Keeping the apex below the rest of the cyclone helps avoid plugging when the underflow contains very large particles and the tonnage of underflow solids can fluctuate.Various devices for adjusting apex diameter or otherwise controlling the underflow are discussed later under ""Cyclone Construction"".BypassingThe transport of a portion of feed slurry directly to underflow so that classification is bypassed by that portion of feed.This action is fundamental in any hydraulic classification, whether gravity or centrifugal, because the large particles going to underflow have some void volume between them, which remains filled with feed slurry.D50By definition, D50 is that particle size which has an equal probability of going to overflow or to underflow.It is calculated by drawing a curve of recovery vs particle size and noting the size at which 500Jo recovery occurs.This may be done equally with corrected or with gross recovery (see below) and the resulting value should therefore be identified as d50c (corrected d50) or as d500 (gross d50).Note also that it is common in industry practice to plot size analysis data on the retained size rather than on the average of passing and retained (the middle of the size band). To portray sizing alone it makes no difference, but to read a D50 value off a curve of corrected or gross recoveries, it is essential to plot those values on the average size of each band."

Jan 1, 1989

By Gerald H. Groenewold

Reclamation of surface-mined landscapes is commonly defined only in terms of biological productivity. Other critical concerns associated with surface mining include the long-term quality of groundwater and stability of the postmining landscape. Meaningful reclamation design must address all these concerns. Reconnaissance of postmining landscapes indicates that three types of instability occur in these settings. These include: area-wide settling, localized collapse, and piping. Area-wide settling is most pronounced during the first year after contouring but appears in precontouring valley areas where frozen materials are contoured with a dozer. Although severe in some settings, development typically ends within one year. Piping appears to be a severe and long-term problem in some settings. Piping usually begins soon after contouring ceases and may continue for several years. In some postmining landscapes, piping has only started to develop after as many as five years of apparent stability. Piping is controlled by a combination of physical and chemical conditions in the spoil. A key factor is the presence of highly dispersive materials in the near surface. The design of a stable postmining landscape requires the integration of severe critical factors. These include: 1) detailed knowledge of the distribution of overburden materials with emphasis upon the delineation of highly sodic sediments; 2) proper equipment selection; and 3) a consideration of climatic factors. For reclamation to be successful, it must consider the entire landscape, not merely the soil zone. Any approach short of this will lead, at best, to temporary solutions.

Jan 1, 1980

This paper was developed as part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to identify risk factors associated with bumps in the prevention of fatalities and accidents in highly stressed, bump-prone ground conditions. Changes of failure mechanism with increasing confinement, from extensional- to shear-dominated failure, are widely observed in the rupture of intact specimens at the laboratory scale and in rock masses. In the previous analysis conducted in 2018, both unconfined and triaxial compressive tests were conducted to investigate the strength characteristics of some specimens of a Utah coal, including the spalling limits, the ratio of apparent unconfined compressive strength (AUCS) to unconfined compressive strength (UCS), the damage characteristics, and the post-yield dilatancy. These mechanical characteristics were found to be strongly anisotropic as a function of the orientation of the cleats relative to the loading direction.

Jan 7, 2020

By Hasan Ozturk

Laboratory testing examined the effect of a variety of intrinsic rock properties and environment conditions that influence the adhesive bond between rock and thin spray-on liners. The liner materials used for these tests were Tekflex, provided by Fosroc, Castonite, provided by Rohms and Haas Co., Rockweb provided by Spray-on Plastics, and CS 1251 2K, provided by Master Builders. Some of the variables examined include: rock strength (tensile/compressive strength) rock mineralogy, rock surface roughness (grain size, fracture/joint roughness), and surface contamination (oil, water or dust). Under optimal conditions, adhesive strengths reaching at least 3 MPa can be achieved. Where the rock surface is contaminated with dust or the rock is weak in tension, it may be difficult to reach adhesion strengths of 1 to 1.5 MPa.

May 1, 2004

By Peter M. Power

A microscopic study was made of a series of simultaneous slag and metal samples taken from a low carbon basic open hearth heat. An attempt was made to identify the various micro-constituents found. As the various impurities in the bath are oxidized, the metal structure changes from that of high-phosphorus white cast iron to that of low.-carbon steel. A detailed study of phosphorus distribution is included. The acid run-off slag has an .acicular orthosilicate structure which changes on 'shape-up' to a very basic tri-calcium silicate and calciuim ferrite structure. Many unidentified minor constituents are present in the slags. Though metallography will never replace chemic.al analysis of the bath, the microsopic study of polished slags has some promise of being useful in slag control work.

Jan 1, 1956

By Andrea Brickey, JUDITH BUABA, RICHARD AMOAKO

The global mining industry has recorded significant declines in accident and injury rates attributed to the advancement in technology, increased enforcement, and safety consciousness. A goal of the mining industry is to achieve zero injury and occupational illness on all mine sites, prompting increased research into ways to further reduce mine accidents. A machine learning technique known as multiclass logistic regression is applied on a 10-year injury dataset from the Mine Safety and Health Administration (MSHA) to determine a miner’s susceptibility to a class of injury and to help identify significant risk factors associated with different classes of injury. The data is aggregated based on injury classification to provide statistically relevant results. The analysis identifies specific risk factors that influence a mine worker’s susceptibility to a given class of injury, i.e., non-fatal with no days lost or restricted activity, non-fatal with days lost and/or days of restricted work activity, and fatal and total permanent or partial permanent disability. These factors include miner’s age, mine type (coal vs. non-coal), experience on the current job (years), shift start time, employment type (operator vs. contractor), mining district, and type of accident. The results of the analysis indicate that a miner’s experience on the job, i.e., the number of years worked in a current job, is a significant risk to injury occurrence, even for those with decades of total mining experience. We further show the differences and similarities between the surface and underground mine incidents.

Nov 3, 2020

Rock mass classification systems are extensively used in rock engineering design work, and mine design is no exception. Among the systems most widely used for mining-related design work are the NGI 0-system (Barton et al., 1974), the RMR system (Bieniawski, 1976), the MRMR system (Laubscher and Taylor, 1976) and, more recently, the GSI system (Hoek et al., 1998). Classifying the rock mass is widely seen as being the fieldwork required to characterize the rock mass and enable the application of empirical design methods associated with the different classification systems. This paper argues that it is fundamentally important to recognize the distinction between rock mass characterization and rock mass classification. These two processes should, in most cases, be separated from each other. Rock mass characterization should be used to determine the intrinsic properties of the rock mass independently of the application; i.e. independent from the infrastructure to be designed, the size, shape, and orientation of the excavation(s) or pillar(s), etc. Rock mass characterization should also be compatible with most classification systems and empirical design methods to be used. Rock mass characterization is the background fieldwork required to perform rock mass classification and/or engineering design work. Rock mass classification is the subsequent step to the characterization, and an integral part of the design process. Parameters that vary according to the design, such as the relative orientation of geological structures compared to the opening or the mine-induced stresses, should be calculated as part of the rock mass classification and design process, rather than during the rock mass characterization process. The failure to distinguish between rock mass characterization and rock mass classification can lead to major design errors and poor results.

Jan 1, 2012

By John E. Conley

The great demand for metallic aluminum for the prosecution of World War II caused the consumption of bauxite, the common ore of aluminum, to increase greatly. Prior to the war, the domestic deposits 'of bauxite, which occur chiefly in Arkansas and less extensively in Georgia, Alabama, and Mississippi, supplied only: about 30 ,percent of the ore required for aluminum-metal production and approximately 40 percent of alumina for all purposes. Enemy activities during the war seriously interfered with shipment of bauxite from the normal peacetime source in Surinam, Netherlands Guiana, South America, and focused attention on the necessity for increasing production from known domestic deposits. Even in peacetime, the production of aluminum ore in the United States could not satisfy requirements. Field drilling and exploration by Bureau of Mines engineers resulted in the discovery of important tonnages of high-grade bauxite suitable for treatment by the conventional Bayer process, Although an ore containing approximately 55 percent Al2O3 and only 2 to 4 percent SiO2 is preferable, it was necessary to use ores containing up to 8 or 10 percent SiO2. Because of the lower recoveries of aluminum with increased silica content, the Reconstruction Finance Corporation, through the Metals Reserve Company, established a base price of $4 for a 50-percent Al2O3 ore, containing 13-percent silica, with a premium or penalty of 14 cents for each percent of Al2O3 over or under 50; each percent of SiO2 under 13 was awarded a 20-cent premium, and each percent over 13 suffered a penalty of 43 cents; all prices were on the basis of 1 long ton of ore, dry basis.

Jan 1, 1949

By Jerry E. Olson

In 1984, the U.S. Bureau of Mines conducted a mineral survey of the Pahute Peak Wilderness Study Area (WSA) (NV-020-621), which covers 57,529 acres in Humboldt County, NV. About 90 percent of the WSA is underlain by Tertiary volcanic and shallow intrusive rocks. Of the remainder, metasedimentary rocks of unknown age are in contact with Cretaceous intrusive rocks in the northwest corner of the WSA. The entire WSA is within an upthrown fault block of the Basin and Range physiographic province. Portions of the WSA, especially south of Pahute Peak (Big Mountain), may be part of an eroded caldera structure. No mines or evidence of major exploration were identified within the WSA. Workings in Copper Canyon, claim blocks along the northwest boundary, and zones of anomalous character as defined by the Bureau of Land Management were examined. No mineral resources were identified, but sample results indicate three significantly mineralized sites, one with indications for zinc skarns in Copppr Canyon, another favorable for precious metals 2 miles south of Copper Canyon, and another area near the northwest boundary with geologic conditions characteristic of molybdenum deposits. Further investigation of these sites is warranted. Petrified wood is present in small amounts near the west central range front.

Jan 1, 1986

Cutter roof failure, a ground control problem that frequently results in massive roof failure, is common in coal mines of the Northern Appala-chian Coal Basin, causing delays in production and posing a safety hazard to mine personnel. The Bureau of Mines is conducting research on the causes of cutter roof failure to gain a basis from which to predict and prevent its occurrence, and to support such roof when failure occurs or is imminent. Research conducted at the Greenwich Collieries North and South Mines, in central Pennsylvania revealed a correlation between the presence of clastic dikes and formation of cutter roof failure. The research con-sisted of in-mine mapping of geologic and deformational features, rock pressure monitoring, core recovery and evaluation, and in situ stress measurement. It was found that roof failure increased in areas where the occurrence of clastic dikes was most frequent, especially where two or more clastic dikes intersect. Staggering of crosscuts prevented the extension of cutters and deterred the occurrence of large falls extending over several break-throughs. In addition, trusses and cribbing were effective in stabilizing clastic dikes and inhibiting the development of cutter roof failure when employed immediately or shortly after mining.

Jan 1, 1987

By H. Lyn Bourne

This is the ninth annual tabulation of royalty information. Again this year, some of the older information has been deleted to make room for more than 30 new entries. Several articles and publications crossed the author's desk this past year that relate to mineral valuation and mineral royalty. Tom Loucks presented a paper, "The Valuation of Hard Rock Mineral Property," at the Rocky Mountain Mineral Law Foundation in Santa Fe, NM in July, 1990. His paper gives an indepth explanation of the definitions and concepts related to mineral valuation. It includes descriptions of numerous legal cases that have dealt with mineral valuation and proper reference is given for each case. Loucks works for the Denver Mining Finance Co. Gold royalties generally range from 5% to 7%, net smelter return. However, Severn Brown sent information that shows a much wider variation. Echo Bay Mines reported in its 1989 annual report royalties that range from 1.5 % to 30% for gold from various gold properties. Brown also sent a copy of an article that appeared in the Dec. 27, 1982, issue of Fortune magazine. This issue carried an article by Walter Guzzardi, Jr. "The Huge Find in Roy Ash's Backyard." The article gives the history of Newmont's leasing in Nevada on property that became the Carlin, Bootstrap and Blue Star Mines. The article states that the initial royalty was 10% that escalated to more than 16%. Another property, the site of Gold Quarry, provides an 18% royalty to the same own¬ers. The article makes interesting reading for those interested in mining history.

Jan 1, 1991

An enhanced gravity concentrator was installed in conjunction with an intensive leach reactor at the Sadiola plant in Mali last year and commissioned in December 2007. There has been much debate over the years as to the effect of gravity concentration on overall plant performance. The late Dr Laplante suggested that for every ten per cent of gold recovered by gravity, there was a corresponding 0.1 per cent to one per cent additional overall plant recovery. The results at Sadiola are consistent with this hypothesis with an overall four per cent gain in plant recovery. With total gold recovery of 12 per cent in the gravity section, grades are increased from 3.54 g/t in the gravity feed to an average of 2 600 g/t in the concentrator feed to the inline reactor. The recovery of gold in the inline reactor is in excess of 98.5 per cent. This paper discusses the background to the project, the laboratory test work prior to the equipment selection, the operational results of the system, as well as the benefi ts of the future application of high mass yield centrifugal concentrators in base metals, sulfides and industrial minerals. Bench scale, pilot scale and plant practice examples are also presented.

Aug 1, 2010

By Bob Munz, Ry Stone

To facilitate the installation of the longwall equipment for each extraction panel, West Elk mine develops set-up room roadways that are between 26.5 and 30.5 feet wide. Historically at the mine, the set-up room roadways have been driven in a single 20-foot-wide pass, then incrementally widened to the required width during installation of the longwall shields. The first pass roof is supported with a generic roof support plan consisting of partially encapsulated roof bolts and point-anchored cables. This ground support plan was utilized regardless of the geotechnical conditions encountered in the roadways or consideration of the required stand-up time of the roadway before the longwall shields were installed. This "blanket" approach tends to result in over-conservative or inappropriate roof support designs, particularly in changing geotechnical environments. Guided by the desire to optimize the ground support plans and increase mining efficiency for future set-up rooms, the West Elk mine and Agapito Associates, Inc. have developed and implemented a strata management program. Strata management, as a formal and structured process, allows ground support and mining methods to be tailored to the anticipated and encountered geotechnical environment in a con- trolled manner (Thomas 2007). To arrive at adequate site-specific ground support plans for the set-up rooms at the mine, several struc- tured processes were utilized. Firstly, the geotechnical environment was characterized by examining the roof lithology and geomechanical properties from nearby rock core obtained from exploration boreholes. To increase both mining efficiency and continuity, and to achieve longer stand-up times before the longwall shields are installed, a multi-pass approach was implemented into the design. During mining, the geotechnical conditions of the roadway are mapped, and the roof is strategically surveyed with a borescope. This process was used to ensure that the encountered ground behavior was in alignment with the design standards used for the roof support design. To support this process with measured data, roof extensometers were strategically installed throughout the roadway. This data was used to monitor the magnitude of roof displacement at various horizons and record displacement rates up until the longwall shields were installed. Lastly, a Trigger Action Response Plan (TARP) was used during mining to cater for any unforeseen changes in ground conditions that would warrant additional con- trols such as increased monitoring or the installation of additional ground support. This paper presents two case histories at the mine where the above strata management approach was implemented to arrive at a site-specific ground support plan. The main changes to the mine's ground control plan included a multi-pass mining approach, the utilization of fully encapsulated roof bolts, and the transition to a stiffer roof support system. The geotechnical mapping, the roof borescope results, and the roof extensometer data will be presented to demonstrate the effectiveness of the ground support system up until the longwall shields were installed in both presented cases.

Jun 25, 2024

By James Addis, Zoheir Khademian, Marcia L. Harris, Charlie Matthews, Y Zheng

Shale gas wells can sometimes drill through coal reserves. Hypothetically, the caving of the gob from longwall coal mines may deform the shale gas well casing and potentially result in a breach. NIOSH researchers studied the permeability of the surrounding ground strata that may affect the potential for an inflow of gas into an underground mine environment. An overview and comparison of measured permeability values under differing cover depths (147 m and 353 m to the Pittsburgh coal seam) and mining cycle phase will be presented and discussed in this report. The findings highlight data-driven experimental evidence that affect the interaction between gas wells extraction and mining operations that may lead to potentially hazardous environments.

Feb 1, 2025

By C. M. Campbell

The Inconceivable Wealth propaganda goes on apace. Premier King, at Vancouver, has stated that we still have, untouched, natural resources, "beyond the wildest dreams." Principal Currie, in an address before the Canadian Society in New York said that Canada's resources, "are as yet merely scratched and it is not possible to compute her almost fabulous natural wealth." Mr. Meighen, in the last election campaign announced that, "under the providence of God, Canada is more richly endowed, perhaps, than any other country in the world." Four years ago a despatch was sent to Premier King "on behalf of" this Institute advising him that "Inconceivable Wealth" in minerals in this country was assured. This was made as a statement ~f "incontrovertible fact." Specifically, this despatch stated that this wealth was on such a scale that the mining industry would in the future lead all others in this country. This inventory is still in effect as far as this Institute is concerned.

Jan 1, 1926

By P. L. M. Wong, N. W. Johnson

Surface analysis by X-Ray Photoelectron Spectroscopy (XPS) of samples taken from the galena flotation section of the Hilton Concentrator of Mount Isa Mines Limited are presented. Flotation rate and pulp chemical data taken during the sampling period are also presented and discussed. Surface analysis suggested that, under normal operating conditions, an overlayer of precipitated calcium sulfate existed at the surface of the sulfide minerals. In particular, there was a decrease in the surface concentration of calcium sulfate for the concentrate samples relative to that occurring on the tailing samples. This suggests that the flotation process was selective against minerals which have calcium sulfate predominating at the surface. Heterocoagulation of hydrophilic calcium sulfate on to the galena surface considerably reduced galena flotation rate. Methods to control calcium sulfate precipitation, which include sodium carbonate treatment of the pulp, are also discussed. Sur- face analysis results of samples taken from the Hilton Concentrator during sodium carbonate addition to the grinding circuit are also presented. This shows clear evidence for the removal of calcium sulfate from the mineral surfaces without concomitant surface precipitation of calcium carbonate. Reasons for the apparent dispersion of precipitated calcium carbonate are discussed. Galena flotation rate was increased by the addition of sodium carbonate apparently due to the removal of interfering calcium sulfate.

Jan 1, 1995

By R. A. Campbell

The electric smelting of five lowgrade Canadian manganese ores has been investigated at the Mines Branch, Department of Mines and Technical Surveys, Ottawa. Ferromanganese, silkomanganese, and spiegeleisen were produced 1by special smelting processes from these ores since the latter were too low grade to be treated by conventional smelting methods. In one case the results were considered to be sufficiently promising to justify the construction of a pilot plant, by the Company concerned, for the further development of the process.

Jan 1, 1956

By W. J. Langford

"Conventional design criteria assume that the fracture strength of a structural material exceeds its yield strength. Fracture below the design load is not expected, y et many structures have failed in this way. The causes of the fractures are almost always discontinuities such as cracks and welding defects. Linear Elastic Fracture Mechanics (LEFM or simply 'fracture mechanics') provides an analytical framework for assessing the influence of sharp defects on the load-bearing capability of a structure. Fracture mechanics techniques have reached the point of acceptance by ASME Design Codes for nuclear components, and ASTM Standards now include well-defined rules for measuring fracture toughness. Starting with a simple equation which relates applied stress and crack size, the influence of the material's thickness and yield strength can be calculated. Thus, the size of defect which will cause failure under the applied stress may be determined. Armed with this information, the metallurgist can assess the safety of a structure from the viewpoints of non-destructive testing standards, construction standards and conditions of operation throughout its service life."

Jan 1, 1976

The Effect of Molecular Weight on the Adsorption and Efficacy of Polysaccharide Depressants

Sep 13, 2010