Search Documents

By Joan K. Kuenzi

This Information Circular brings together for consideration recommendations from U.S. Bureau of Mines research in the area of surface mine mobile equipment maintenance for the period 1982 through 1991. It updates the 1982 contract report by Baker and Alves that formed the basis for much of the work described in the present report. Recommendations for hazard abatement during work on mobile one equipment are presented and stem from the results and recommendations of the research in two areas: (1) equipment and workplace hazard reduction, and (2) management of maintenance information. Recommendations included in this report apply to both the operators and maintainers of mobile mining equipment as well as to the manufacturers of that equipment.

Jan 1, 1995

By C. Lambert

It has been shown that contacts between host rock and engineered barriers may be critical in the design of deep radioactive waste repositories. Water is expected to reach the interface zone after the re-saturation of the geological massive and its presence may lead to concrete leaching. Such a phenomenon could increase the interface transmissivity and compromise the confinement of radioactive waste. Recent experimental results from Buzzi et al. (2008) have enhanced how concrete leaching can drastically change the mechanical behaviour of such interfaces. Because of the local loss of strength resulting from leaching, shearing resulted in a degradation of the interface asperities. Similarly to rock joints, intact interfaces exhibit a usual contracting-dilating behaviour. On the contrary, depending on the extent of leaching, the degraded interface can display a fully contracting. This paper intends to investigate the influence of concrete leaching on the mechanical behaviour of host rock-concrete interfaces. The leaching process consists in the dissolution of some of the hydrates of the cement paste, leading to a reduction of the strength and Young's modulus. A discrete model has been developed with PFC3D where a simplified interface morphology has been introduced using a saw-tooth description of the asperities.

May 1, 2009

By G. B. Atkinson

The Bureau of Mines investigated a method for increasing the leaching rate of bulk superalloy scrap to facilitate recycling and recovery of critical metals such as Ni, Co, and Cr. Three superalloys were investi- gated, the cast-nickel-base superalloy IN-738, the wrought-nickel-base superalloy Rene-41, and the cast-cobalt-base superalloy Mar-M-509. Superalloys melted with 20, 30, 40, and 50 pct Al metal to form inter- metallic compounds were easily crushed to a convenient particle size and reacted rapidly with acid solutions which dissolved the metals. For example, leaching 1/2-in pieces of unalloyed IN-738 with excess 6N HC1 at 95° C for 2 h dissolved about 0.5 pct, while leaching 10 g of minus 20-mesh 30 pct Al-70 pct IN-738 with excess 6N HC1 at 95° C for 2 h dis- solved 96.2 pct.

Jan 1, 1983

By Arka Jyoti Das, Prabhat Kumar Mandal

"Coal mining in India has a strategic importance for the energy security of the country. Presently, the majority of coal production is coming from open-cast mining. Due to the fast depletion of reserves amenable to open-cast mining, future coal production will depend primarily on underground production. In conventional bard-and-pillar/room and pillar mining as it is practiced in India, the percentage of extraction is very low. In fact, within most Indian coalfields, a large number of coal seams extract only 15- 20% of coal, but no pillar extraction is done due to the presence of surface or sub-surface structures leading to huge amount of coal being locked-up in underground. Spontaneous heating and fire, the accumulation of poisonous gases, severe stability issues, unsafe workings and environmental hazards are all major problems associated with these developed coal pillars, so there is a pressing need for technology in the mining industry to extract this huge amount of coal locked up under different constraints. In this study, we propose that the locked-up coal be extracted by replacing the developed coal pillars with artificial pillars. The paper briefly discusses the extraction methodology designed for this and its evaluation through numerical modeling for applied suitability underground.INTRODUCTIONDriven by rising populations and urbanization, an expanding economy and also a quest for improved quality of life, energy usage in India is expected to increase manifold in the coming years. As for India's energy scenario and its projected future plans, there is no doubt that coal will remain a prime source of energy, even over the next few decades.The majority of coal production in India comes from open-cast mining because of large-scale mechanization, but the coal reserves amenable to open-cast mining are gradually depleting - which may impose adverse impacts on the energy sector if underground production does not increase. Underground coal extraction, meanwhile, is going to become more complicated in near future due to the fast exhaustion of easily mineable coal reserves."

Jan 1, 2016

By Cem Colakoglu

In this study, nickel containing iron alloys were produced by carbothermal reduction of lateritic nickel ores obtained from Manisa - Caldag region of Turkiye in order to investigate the reaction mechanism of nickel and cobalt. In the experiments, the lateritic ore containing 1.58 wt.% Ni and 0.12 wt.% Co was calcined in a semi-pilot scale rotary furnace at 1100°C for 1 hour. Then, a mixture of calcined ore and metallurgical coke was reacted in sintered alumina crucibles using a graphite resistance tube furnace at different time (0- 60 min) and temperature (1500-1600°C).

Jan 1, 2009

By J. F. T. Agapito, G. P. Bratton

A 16 m by 4.7 m by 24.5 m (52 ft by 15.5 ft by 80.5 ft) underground ore bin was constructed at an 810 m (2660 ft) overburden depth in poor quality, faulted and altered intrusive rocks at Molycorp's block caving molybdenum mine. Geological engineering incorporated detailed structural mapping, rock quality classification, in-situ stress field determinations, numerical stress and failure analysis, and convergence monitoring. The ore bin was mined by conventional methods from the top down and utilized a bored raise for mucking. The initial ground support of rock bolts, lightweight steel sets, and reinforced concrete was later supplemented with an array of 6, 12 and 21 m tensioned, grouted rock bolts when wall closure was noted in the upper ore bin area. The supplementary support was optimized by computer analysis and monitoring.

Jan 1, 1985

By B. Pesic

The recovery of silver and gallium from flue dust with acidified thiourea solutions was examined. The studied parameters were temperature, particle size, thiourea concentration, acid concentration, and the presence of oxidants. The study of the extraction of these two metals was undertaken in sulfuric acid medium. Silver dissolution was dependent on all examined parameters, whereas gallium extraction was only dependent on the initial acid concentration. The experimental results suggest a new very efficient method for recovery of both silver and gallium. Almost complete recovery of silver and gallium can be accomplished within 90 minutes. A technological scheme for recovery of both metals is also proposed.

Jan 1, 1986

By C E. Vidal

Geological exploration and mining development increased their intensity and rate of success during the last five years in Peru. Particularly relevant are the mining projects of Yanacocha and Pierina for epithermal Au and Ag. Also relevant are the new mining operations at Iscaycruz and Uchucchacua for limestone replacement Zn- or Ag-rich base metal skarn deposits. Miocene continental volcanics host the low-grade but near-surface orebodies of the Yanacocha mining district in Cajamarca. Several deposits have been mined since 1994 with open-pit and heap-leach gold production increasing from 300 000 ounces to 1 300 000 ounces in 1998. In a similar geological setting, but with three times the grade of Yanacocha, the Pierina valley-leach operation in Ancash is set to produce 800 000 ounces Au during 1999. At Iscaycruz in Lima, Cretaceous limestones host massive pyrite and sphalerite skarn deposits with 10 to 20 per cent Zn. Mining and milling were started in 1996 with last yearÆs production rising to 180 000 tonnes of Zn concentrates. At Uchucchacua, selective underground mining of fracture-controlled Ag skarns, with 400 to 420 g/t, has been recently increased from 1200 to 2000 tonnes per day to produce 5.5 million ounces Ag during 1998. Advanced exploration projects are located in the framework of nine Phanerozoic metallogenic provinces. Mineral deposits of preferred attention are precious metal disseminations and veins, base metal replacements and skarns, porphyry Cu (Mo-Au), Mississippi-Valley-type Zn and base metal volcanogenic massive sulphide deposits. Geological discovery of new orebodies enables a sustainable development of the mining industry in the country.

Jan 1, 1999

By R Salmimies

Choosing a ceramic capillary action filter is often favoured in processes where low energy consumption is important, such as the dewatering of iron ore. In addition, the performance of the filter medium is essential, and the possibility to regenerate the medium is an advantage compared to other types of filter media. Although low, roughly 8 - 9 w-per cent for iron ore concentrate, and even cake moisture is the primary goal of dewatering, the introduction of better filtration processes can result in significant improvements of water economy and material efficiency.As industrial beneficiation processes are often complicated in their chemistry due to impurities originating from the ore itself, from the up-stream processing equipment and from the process water used, the characterisation of the filter media after usage might provide relevant information on what actually takes place during long operating periods. The aim of this study was to obtain new information on the fouling of fi lter media in an iron ore process to enhance and develop the regeneration process of the media in the future.X-ray diffraction and scanning electron microscopy were used to characterise ceramic filter media used in the dewatering of magnetite. Principal component analysis and discriminant analysis were introduced to identify trends in the data. Two types of media blockages were found to play an important role in an acidic iron ore dewatering process: fouling by slurry particles and by in situ crystallisation of a calcium compound, of which the latter originated from the combination of process water and process chemistry.

Jul 11, 2011

By K Firmin

The Mt Tom Price orebody of Hamersley Iron Pty Limited consists of a folded hematite - shale sequence capped by a layer of goethite. Consequently, variations in iron content occur within the ore body, and as the overall grade is below that required to make specification products, selective mining must be carried out. A necessary preliminary to quality control of products based on selective mining is the production of advance data on the tonnages and grades of material to be expected in future mining areas. Bench plans showing zones of different grades and types of material anticipated are prepared from structural geological information. The grades of materials on a bench are essentially governed by the positions and attitudes of the shale bands. Quality control is exercised by blending different grades and types of material in primary crusher feed. Iron grade is the prime grade consideration although sometimes the level of phosphorus content must be considered. Pre-production grades are determined from assay of samples taken from blast hole cuttings. As shales are more friable than hematite, product fines are always lower in iron grade than the lump product. The realisation of contract specification grade is more difficult with fines than with lump, so maintaining the correct fines grade becomes a prime factor in quality control. Control of fines grade is presently effected by aiming for an appropriate feed grade to the primary stockpile. Studies to estimate fines grade directly by qualitatively taking into account material types are in progress. Quality control measures are checked by monitoring the crushing and screening plant output, and taking appropriate compensatory actions in the mine when required. Minor fluctuations in quality of fines can be blended out on stockpiles. The quality control measures described ensure constant quality products, and a good recovery of high grade material from the deposit.

Jan 1, 1971

By J. W. Wang

This article first explains the mechanism of forming strength in the Jet grouting reinforced foundation, and points out the function of cement hydrates and clay minerals in clayey soil, the reinforced body with the character of long-term growth of strength. Secondly, regarding the strength and the deformation characteristics of compound foundation, the article points out that the stress-strain curve of the jet grouting pile is approximate to hyperbolic curve. Finally, the article cites three examples of application in the construction of the metallurgical industry.

Jan 1, 2010

By Sarkis G. Ampian

Extraction of alumina was correlated with the sinter and leach products from the lime soda sinter process for anorthosite. The effect of composition and grain size of reactants, time and temperature of sintering, and techniques of sample preparation were investigated. Greater than 90 percent Al2O3 extractions were obtained from dry-mixed minus 200-mesh anorthosite sinter mixes having mole ratios of CaO/SiO2 = 1.8 and Na2O/Al2O3 = 0.8. These sinter mixes were briquetted at 15,000 psi and fired between 1,200° C and 1,320° C for 20 to 60 minutes. The sinter phases that contribute to low alumina recovery were determined by X-ray diffractometry, optical microscopy, and electron probe X-ray spectrography. The mechanism of the sintering reaction was investigated by high-temperature X-ray diffractometry. The contrast in the lime soda sinter process for clays and for anorthosites are discussed. Explanations and suggested solutions are presented for problems such as gelation and variable alumina recovery encountered by previous investigations.

Jan 1, 1967

By Douglas Bartley, Jay Elkin

The state of Pennsylvania was at one time one of the leading coal producing states in the east. However, legislation and industry trends over the last 10 years have adversely affected the amount of bituminous coal mined in Pennsylvania and the whole eastern United States. The application for and approval of a new mining permit is a very costly and arduous task. When a new mining operation is established it is crucial that nothing within the operator’s control causes the operation to stop producing. This paper discusses the action taken by a small mine in Pennsylvania when their blast induced vibrations rose to levels that typically would have resulted in a total mine shut down by the regulatory body governing such operations.

Jan 1, 2003

By Neil Campbell

"The gently-dipping Devonian dolomite beds south of Great Slave lake in northern Canada are nearly every-where concealed by a cover of glacial drift and muskeg. Nevertheless, in 1898 or earlier, four small outcropping areas of dolomite, richly mineralized with lead and zinc sulphides, were discovered. Exploration work performed here up to the end of 1930, included intensive trenching and drilling of the showings, together with mapping and wide-spaced drilling in the surrounding region. This work proved that the discoveries are isolated pockets of mineralization much too small to be commercially valuable by themselves. No evidence of orebodies elsewhere was reported.Meanwhile, mapping by the G.S.C. in the Shield far to the east disclosed major Precambrian faults, some of which can be projected southwesterly (under a cover of Paleozoic sediments) to the vicinity of Pine Point. During the period from 1940 to 1947, consideration was given, by The Consolidated Mining and Smelting Company Ltd., to evidence of a theoretical possibility that, although apparently dormant in Paleozoic times, these faults may have provided a structural control and a source of ore-bearing solutions in some post-Devonian period. From this, it was postulated that the breaks might have created, in the overlying dolomite, a linear array of orebodies concealed by overburden but lying in a belt of considerable length and in a position predictable within practical limits. A program of drilling designed to test and exploit this specific concept was conducted from 1948 to 1955.he drilling within the new, theoretically-defined search area resulted in the discovery of many lead-zinc ore-bodies, none of which was exposed at the surface. Some of these are large and (as indicated by 1965 production records) very rich. They are situated 1 to several miles distant from, and apparently not connected to, the earlier-known surface discoveries. The drilling also disclosed that the ore, which consists of disseminated sphalerite and galena replacements together with colloform sphalerite and coarse galena cavity fillings, occurs mainly at certain stratigraphic horizons within a large, coarsely-recrystallized dolomite barrier reef. Considerable fracturing and folding was found. It has been suggested that reef development was influenced by post-Precambrian tectonic movements associated with the old faults in the basement complex. The ore may have been deposited by solutions moving from distant sources to favourable structural and chemical environments in or related to the reef.In more recent exploration performed in the course of preparing for mining production, the rate of ore discovery within the same general geological context has been greatly accelerated by the use of new geophysical techniques and drilling equipment. Reserves of 21.5 million tons, averaging 4 per cent lead and 7.2 per cent zinc, were reported in 1965, and production from open pits at the rate of approximately 248,000 tons of concentrates per year is in progress"

Jan 1, 1966

By John E. Urosek, Dennis A. Beiter, William J. Francart

In This Chapter [Designing bleeder systems Examining and maintaining bleeder systems Evaluating bleeder system effectiveness] INTRODUCTION Bleeder systems are that part of the mine ventilation network used to ventilate pillared areas in underground coal mines. Pillared areas are those in which pillars have been wholly or partially removed, including the areas where coal has been extracted by longwall mining. Bleeder systems protect miners from the hazards associated with methane and other gases, dusts and fumes, and oxygen deficiency that may occur in these mined-out areas. Effective bleeder systems control the air passing through the area and continuously dilute and move any methane-air mixtures and other gases, dusts, and fumes from the worked-out area away from active workings and into a return air course or to the surface of the mine. A bleeder system includes the pillared area (including the internal airflow paths), bleeder entries, bleeder connections, and all associated ventilation control devices that control the air passing through the pillared area. Bleeder entries are special air courses designed and maintained as part of the mine ventilation system. [This chapter focuses on the design, examination, maintenance, and evaluation of bleeder systems in underground coal mines.] The history of coal mine explosions in the United States is a reminder of the importance of adequate ventilation. Some of those disasters were the result of inadequately ventilated pillared areas. The importance of developing bleeder systems to ventilate these pillared areas and evaluating the bleeder system’s effectiveness is reflected in present-day federal regulations. For more information on bleeder systems, see Tisdale [1996] and Urosek and Francart [2002].

Jan 6, 2006

By H. Dong, J. J. Valencia, L. Nastac

"A comprehensive computer model was developed to understand and optimize the centrifugal casting process for manufacturing TiC/Al-bronze friction drums. Performance of these components requires proper distribution of TiC particles, which is shown by dimensional analysis to be dominated by centrifugal buoyancy effects and solidification kinetics.The model addresses the following: (1) a rheology-viscosity model of the interference between moving particles, (2) engulfment (entrapment) or pushing of particles in the mushy region by the advancing solid/liquid interface, (3) nucleation and growth of equiaxed and eutectic phases, (4) effects of particle size, particle concentration, and cooling rate on the final grain size, and (5) the impingement effect of particles on the nucleation and growth kinetics of solidifying microstructure.Parametric studies were conducted using the computer model to investigate the effects of various process and material parameters on the distribution of TiC particles. The effects of the volume fraction, size, and morphology of the particles (including clusters and agglomerates) on the particle distribution were evaluated in detail. The complex interaction between the solidifying structure and insoluble ceramic particles in centrifugally-cast metal-matrix-composites was also investigated.The model predictions of particle distribution and microstructure were validated with experimental data for centrifugally-cast A356/SiC and TiC/Al-bronze alloys.This work was conducted by the National Center for Excellence in Metalworking Technology, operated by Concurrent Technologies Corporation under contract No. N00140-92- C-BC49 to the U.S. Navy as part of the U.S. Navy Manufacturing Technology Program."

Jan 1, 2000

By Ad. Breyre

[Internal-combustion engines have been used in Belgian mines for a long tine. As early as 1899, the use of these engines underground was considered, but the general policy was to prohibit such an application unless ministorial permission was granted' in special instances. At that time only gasoline engines were available, and a few of these were installed as stationary engines, although in general they were replaced later by electric or compressed-air motors. However, the number of gasoline locomotives continued to increase. Regulations governing the use of these locomotives soon were formulated and as early as 1920, when a now set of regulations was promulgated, the use of gasoline locomotives in mines could be authorized by the Provincial Inspection Department and no longer depended on obtaining a ministerial decision. Since 1931 this authorization may be given by the Chief Inspector of Mines, Director of the Mining District. Since 1920, safe practices have boon incorporated in the regulations.]

Jan 1, 1940

By Ad. Breyre

Internal-combustion engines have been used in Belgian mines for a long time. As early as 1899, the use of these engines underground was considered, but the general policy was to prohibit such an application unless ministorial permission was granted in special instances. At that time only gasoline engines were available, and a few of these were installed as stationary engines, although in general they wore replaced later by electric or compressed air motors. However, the number of gasoline locomotives continued to increase. Regulations governing; the use of these locomotives seen were formulated and as early as 1920, when a new set of regulations was promulgated, these of gasoline locomotives in mines could be authorized by the Provincial Inspection Department and no longer depended on obtaining a ministerial decision. Since 1931 this authorization may be given by the Chief Inspector of Mines, Director of the Mining District. Since 1920, safe practices have been incorporated in the regulations.

Jan 1, 1940

By M. Tominaga

An industrial port complex was constructed on the west coast of Leyte Island The work was started in December 1981 and completed in May 1984. This port complex includes a 665 m long wharf and can accommodate vessels ranging from a 60,000 DWT ore carrier to a 4 000 DWT general cargo ship. It now handles materials for and products from a copper smelter with an annual capacity of 130,000 t and a fertilizer plant with an annual capacity of 900,000 t. The Wharf structures consist mainly of interlocked steel pipe piles, steel sheet piles and steel pipe Piles. Material handling equipment such as unloaders, shiploaders, etc. were installed on the wharf. Site survey, planning, engineering design and construction aspects of the port development are discussed in this paper with particular emphasis on the wharf structure.

Jan 1, 2010

By C. E. Gerity

Near Bunker, Mo., in the New Lead Belt, Ozark Lead Co. operates a 6000 tpd lead-zinc mine. Mined ore is transported to the surface in three mechanized and automated steps. The mine is developed by a rectangular-shaped sublevel haulage drift 15 ft high by 28 ft wide, driven on strike below the ore zones. Ore transfer raises were driven from the sublevel at locations near the shaft, 1500 ft distant, and on subsequent 1000 ft centers. These 6 x 5-ft raises are slashed to obtain maximum storage below dump points. These dump points are located on each mining level and are of steel and concrete construction. Spiral 12 X 24-ft inclines driven from the sub-level provide access to these levels for equipment and mine utilities.

Jan 11, 1972