Search Documents

The polymerisation of silica is found to interfere with thickening of leach pulps at Risdon. Hydroxyl ion and fluoride ion are catalysts for this reaction. Stability may be obtained by the presence of aluminium or ferric iron.INTRODUCTIONAt Risdon it has been a matter for satisfaction that, although the concentration, of silica in leach solutions is appreciable, it has ,given relatively little cause for anxiety.However the margin of safety is small and some intermittent difficulty in thickening leach residues during the last few years has prompted a further investigation, certain parts of which are described here since they may be of general interest.Leaching and ClassificationThe method of leaching which is practised at Risdon has been described in, two previous articles, by W. C. Snow (1936) and S. W. Ross (1949) to whiCh the reader is referred for detail. Continuous leaching is practised, the circuit solution flowing through five air agitated pachucas in series, to tlie first of which calcine is added. The circuit solution, which also enters the first pachuca, consists of spent electrolyte from, the electrolytic cells and contains 90 -gm. of free sulphuric acid per litre. About 80 per cent of the solublezinc oxide is extracted from the calcine in the first pachuca, at a pH value of 1-1 (7 gm.H2S04/1 at 55 to 60°C. In the later pachucas the leaching rate decreases sharply. The leach pulp which leaves the 'last pachuca contains an average of 17 gm. of free acid per litre, corresponding to a pH of 1.7; but, owing to variations in extraction, the end point fluctuates between 2.5 and 0·3 gm. free acid per litre (pH:> 1·5 to 2.5). The average flow through the plant is 1,250,000 gallons per day, which corresponds to a production of 300...

Jan 1, 1958

Of late there have been various papers published on this subject by various authorities, in which certain definite factors influencing slime settlement have been brought forward. As the principles set forth by these writers are of great interest, and have, in most cases, been generally accepted, the author will review them in the hope that by discussion some more knowledge may be brought to bear on many points connected with the subject.The definition of slime at the present time is not a standard one, and varies according to different authorities, some defining slime as ore crushed to such a fineness that it will pass through a screen of standard size, say 150 or 200-mesh, in water (1, 2);others as that part of the finely-crushed material which is in the physical condition which causes it to remain in. suspension in water, and possesses pr?perties which render it almost unleachable (3). Authorities seem divided on this point, but of late American writers seem to prefer the former definition. On the contrary, B L Gardiner describes slime as a mixture of small particles of crushed ore of varying sizes which, when mixed with water, tend...

Jan 1, 1912

By Georgy Cherkashov, Svetlana Babaeva, Tamara Stepanova, Firstova. Anna

Seafloor massive sulfides (SMS) study in the Russian Exploration Area at the northern equatorial Mid Atlantic Ridge began after signing the contract with International Seabed Authority in 2012. In order to evaluate the SMS resources in the course of exploration the major and rare metals with economic value should be determined. The evaluation is based on geochemistry and mineralogy and particularly on the type of rare metals occurrence in the SMS. As a case study research of the Semyenov cluster of SMS deposits have been conducted.

Sep 1, 2014

By Gerry Houlahan

The east span of the 3.5 km long SF-Oakland Bay Bridge is supported by different types of foundations along its span. Starting from the west, its first 460 m section comprising twin concrete box-girders is supported by sands and rock on Yerba Buena Island. A 620 m long steel suspension span then bridges a 25 m deep channel that is formed in sediments overlying rock. Twin concrete box girder structures, each 2.4 km long, complete the stretch over the remainder of San Francisco Bay to the engineered earth fill landing at its east end. For most of its length, the Skyway bridges water 3 to 10 m deep over soft surficial Young Bay Mud. The foundation types include spread footings with hold-downs, steel and concrete piles that are set in drilled rock sockets up to 3 m in diameter and 2.5 m diameter steel tubular piles driven to penetrations of up to 100 m. The design and construction-related considerations are presented. The different foundation types, influences of the site geology and earthquake demands on the substructures are discussed. The seismic motions of the bridge superstructures and substructures, as well as the depth-varying soil motions, influenced the foundation design. Together with performance-based design criteria, including post-earthquake footing displacement limits, these seismic demands influenced various aspects of the foundation design, including the use of battered and vertical piles.

Jan 1, 2005

By C. Allen

In 2004, Boliden Odda underwent an extensive modernisation project targeting mainly the leaching section of the plant. Direct leach technology was introduced as part of this project. The Direct Leach process, developed by Outokumpu, is an atmospheric oxidative leach of zinc sulphide concentrate. The effects of this new processing operation on behaviour of iron in the plant are discussed. As well, the filterability of the new residue on belt filters prior to its deposition in mountain caverns is also discussed. The solids from the direct leach process have been analysed by scanning electron microscopy, and the results of these analyses are presented.

Jan 1, 2006

By I. McDougall

The matte/slag tidal zone in a nickel-copper-iron-sulphide matte smelting furnace is subject to severe process conditions that can lead to premature failure of the lining. The MgO-FeO-SiO2 slag is aggressive to refractory bricks, while the Ni-Cu-Fe-S matte is aggressive to water-cooled copper cooling elements, and can penetrate and sulphidize refractory bricks. A novel approach to the lining design was taken at a PGM smelting furnace, where an indirectly-cooled graphite ring was applied in the matte/slag tidal zone, with refractory bricks on the hot face. The graphite was cooled by the copper cooling elements in the slag zone, obviating the need for copper cooling elements in the tidal zone. In this paper the effectiveness of different lining designs utilizing varying degrees of cooling in the slag zone and slag/matte tidal zones is compared. In comparison to water-cooled copper in various configurations, cooled graphite shows promise as an indirect refractory cooling system in the tidal zone area of furnaces. Keywords PGM smelting, graphite, refractory lining, copper cooling elements, submerged arc furnace.

Aug 1, 2013

By A Vigar

Siliceous float sampled in the Wafi River by CRA Exploration in 1977 assayed 22 g/t Au and 89 g/t Ag. Follow up in 1979 led to the discovery of outcropping mineralisation now known as Zone A. Soil sampling in 1980 and 1982 outlined a 350 m by 400 m area of >1 g/t Au at Zone A and smaller areas at Zones B, C and D. Thirty-one diamond holes were drilled between 1983 and 1986. Elders Resources continued evaluation of Zone A under a farming agreement between 1988 and 1990. Mineralised diorite porphyry was discovered in 1990 by drilling conceptual targets 500 m to the NE of Zone A. Evaluation of this copper-gold porphyry became the main focus of exploration for the next five years and a substantial resource was outlined within a single, discrete body. A review of the paths to project development in late-1995 highlighted the need for increased resources via a second mineralised porphyry and/or an additional resource of Zone A size to make the project viable. It was concluded that the greatest immediate potential for increasing the resource inventory was at Zone A itself where the mineralisation was open in all directions. Detailed mapping and drill core logging lead to the geologic and structural models being revised in early-1996. The objectives of the 1996 drill program were to extend the Zone A resource, to test for continuity of mineralisation westwards to Zone B, to better define the controls on gold mineralisation and to delineate high-grade blocks amenable to selective mining by infill drilling and 3D orebody modelling. The last drill hole of 1996 intersected 30 m at 4.6 g/t Au from 273 m in WR147, deep in the western limit of Zone A. This intersection gave impetus to continue drill testing towards Zone B. In April 1997, hole WR154 was drilled 100 m to the west of WR147 and intersected 20 m at 8.5 g/t Au and 70 m at 11.0 g/t Au at similar depths near the diatreme contact. Drill hole WR155 was then drilled 100 m to the west of WR154 and intersected 86m at 5.7 g/t Au and WR159 drilled 100 m to the south of WR154 intersected 36 m at 9.2 and 50 m at 4.4 g/t Au. A significant zone of essentially blind, high-grade gold was discovered beneath the dipping flank of a poorly mineralised diatreme in what became known as the Link Zone. The long history of evaluation has been driven by the conviction of a dedicated team that a mineralised system of the size and complexity of Wafi with strongly anomalous gold in outcrops over the entire Mount Golpu area must contain economic mineralisation hidden within it. The keys which redefined the direction of exploration and lead to the discovery of the blind, high-grade gold Link Zone were, in our view, the critical review of the project status, detailed geological and structural studies to define clear exploration targets and the necessary funding and persistence to carry this through.

Jan 1, 1999

By O. Konovalov, M. Zhuravkov

In report the results of performance of research works on building up of the connected geoecological and geomechanical monitoring system for modelling and study of a state of mining massif in a region with large-scale underground mining works are discussed. The connected geoecological monitoring requires radical change of methodology of carried out works. To carry out modelling and researches it is impossible without construction of the integrated connected information model of region. Basis of construction of information systems and databases for all sections of Earth Sciences is the set of the approaches, among which, for example, methods of remote sounding, GIS- and GPS-technology etc. Computer technologies are basis on the "supercomputer" technology. The results of performance of some researches for regions of excavation of deposits of potash salts in Russia and Belarus are presented.

Jan 1, 2005

By Stephen A. Swan

Certain types of mobile surface mining equipment are required to be equipped with rollover protective structures (ROPS) capable of protecting the operator in case of a rollover accident. The Bureau of Mines has developed ROPS performance criteria for wheeled front-end loaders. This report reviews the development of rollover test procedures and subsequent testing of ROPS for 52,000-, 286,000-, and 390,000-lb gross vehicle weight (GVW) loaders. The program consisted of both dynamic (roll) and static tests to assist in the development of the ROPS performance criteria. Each test included extensive instrumentation and photographic documentation to fully evaluate the performance of the ROPS. Data summarizing side, longitudinal, and vertical force and deflections are included. The data indicate that for loaders in excess of 240,000 lb, GVW, a side force-to-mass ratio of 1.0 and an energy-to-mass ratio of 6.0 appear to be adequate criteria to protect an operator in the event of a 5400 rollover. For smaller machines, Society of Automotive Engineers (SAE) 11040 performance criteria provide adequate protection. Longitudinal loading, though not ad-dressed in previous ROPS performance criteria, was shown to be a potentially significant factor in ROPS failure. Longitudinal loading and energy criteria equal to 80 pct of side loading criteria are recommended.

Jan 1, 1988

Plant for the production of sulphuric acid from pyrites flotation concentrates was commissioned at Cockle Creek during 1956, to meet increasing demands for commercial acid and superphosphate. Pyrite was chosen as raw material because of the uncertain supplyposition of imported brimstone and the desirability of utilising domestic sulphur.Desulphurisation of the pyrite is performed by two 40-ton per day roasters of the Turbulent Layer type operated under licence from the Badische Analin and Soda Fabrik (B.A.S.F.) organisation. These units are the first of their kind commissioned in the southernhemisphere. Pyrite is fed to the roasters in the as-received un-dried condition. Waste heat steam production is coupled with electricity generation within the plant. Sulphur dioxide is produced at comparatively high strengths and cleaned by conventional cyclone and hot electro-filter equipment.The acid unit has a capacity of 100 mono tons of sulphuric acid per day and includes cooling and wash towers, mist precipitators, a single stage drying tower, 4-pass oxidation section and absorption system.INTRODUCTIONSulphuric acid has been manufactured at Cockle Creek Works since 1913, when the first chamber nitration plant was commissioned. The raw material was brimstone roasted in Herreschoff furnaces. Since that time three additional chamber units have been constructed and have produced acid from brimstone, zinc concentrates, pyrites and -spent oxide, according to changing economic and supply factors.Three chamber units are still in operation. Contact processes have become increasingly important since the first Schroder-Grillo unit was commissioned in 1923. Six of these 5-ton per day units were operating in the mid-thirties, but have since been demolished. Two 15 ton Chemico hot gas contact units commenced operation in 1937 and 1938, and although modified, are still in service.The increasing demand over recent years for sulphuric...

Jan 1, 1957

By M Carter

The Great South Basin is located beneath the northwest part of the Campbell Plateau, a+broad, nearly level, triangular shaped submarine platform, southeast of the South Island of New Zealand. It encompasses an area of 77 700 square kilometres and contains a sequence of Cretaceous to Tertiary sedimentary rocks which are up to 6000 metres thick near the centre of the basin (Shirley, 1983). The western boundary of the basin is adjacent to the steep Aucklands Slope. In the+ north it merges with the Canterbury Basin and to the south onlaps against the Pukaki Rise, a basement high. The eastern margin of the basin is bounded by the northeast - southwest trending steep linear Antipodes Scarp. In the extreme south the Antipodes Scarp curves westward and joins the north trending Aucklands Slope. The Campbell Plateau is dominated by tensional tectonics. The Antipodes Scarp represents a major region of transcurrent faulting initiated by Cretaceous rotation within the Campbell Plateau. Later movements are associated with the Alpine Fault of the South Island (Sandford, 1980; Anderton, Holloway, Engstrom, Ahmad and Chong, 1982).

Jan 1, 1983

By S. S. Gajin

The paper deals with parametric vibrations of an axially loaded pile. The dynamic model is derived by means of Hamilton's principle and reduced to a partial differen­tial equation with variable coefficients and corresponding initial boundary conditions, taking into account the influence of the axial force. By means of Galerkin's method, the partial equation is further reduced to a Matheu-Hill's matrix partial differential equation of the second order. Since the problem of the dynamic stabili­ty has been expressed only for standing piles, the paper analyses in detail two stan­ding piles, one which is restreined, whereas the other is hinged at the toe. In both cases it is assumed that head horisontal displacement is prevented. Using Ruunge-Kutt's method, a computer analysis in the time domain is given for the characteristic parameters and possible boundary conditions. The paper analyses the stationariness of the process, as well as the dependance of the critical excitation frequency upon the pile parameters. The results have been illustrated by respective diagrams.

Jan 1, 1989

By L. Yuan, A. C. Smith

To provide insights for the optimization of ventilation systems for U.S. underground coal mines facing both methane control and spontaneous combustion issues, a computational fluid dynamics (CFD) study was conducted to model the potential for spontaneous heating in longwall gob areas. A two longwall panel district using a bleeder ventilation system with a stationary longwall face was simulated. The permeability and porosity profiles for the longwall gob were generated from a geotechnical model and were used as inputs for the CFD modeling. In this study, the effect of methane emissions from the mined coal seam, including the longwall face and overlying rider seam reservoirs on the gob gas distribution was considered. The spontaneous heating is modeled as the low-temperature oxidation of coal in the gob using kinetic data obtained from previous laboratory-scale spontaneous-combustion studies. Unsteady state simulations were conducted, and the effects of the coal’s apparent activation energy and reaction surface area on the spontaneous heating process were also examined.1

By S Jokanovic, J L. Mauk

The Taharoa ironsand deposit covers approximately 16 km2 and is located 144 km south of Auckland on the west coast of the North Island, New Zealand. The heavy mineral-rich sands predominantly contain titanomagnetite, ilmenite and hematite, along with lesser amounts of amphiboles, pyroxenes, and feldspars. Throughout the Taharoa mine site 142 samples were collected of which approximately 25 samples were used in mineralogical analyses of the magnetic, heavy non-magnetic and light non-magnetic fractions. Mineralogical and petrographic analyses confirmed the high abundance of homogeneous magnetite and magnetite containing ilmenite exsolution lamellae which have oxidised to hematite. A limited number of sand samples were collected from Taranaki beaches. Petrography reveals exsolution textures of magnetite and ilmenite (now hematite), and homogenous magnetite grains similar to those observed at Taharoa. Petrographic analyses from previous research projects were also closely investigated in order to make mineralogical comparisons from along the west coast of the North Island and with other potential source areas. The origin of detrital magnetite grains along the west coast of the North Island is generally presumed to be the eroded volcanic cones of the Egmont volcanoes and active and dormant volcanoes of the central North Island. Electron microprobe analyses of magnetite grains from Taranaki beach samples reveal TiO2 values of between 1.5 and 120 per cent. MgO and A12O3 contents also vary widely from 0.75 to 6.5 per cent. This large variability may reflect different volcanic eruptions, the presence of exsolution textures or alternative source areas for these magnetite grains. Geochemical results from the Taharoa mine site correlate with the Taranaki beach samples suggesting that the Egmont volcanoes are certainly one source area. Variability in XRF results, especially Fe and Ti contents (9.04 - 59.22 and 0.80 - 4.64 respectively), from the magnetic and heavy non-magnetic fractions likely reflect the detrital nature of this deposit.

Jan 1, 2003

By Kurt F. Weitz

"The number of materials that can be classified as fillers covers an extremely wide range: this paper outlines those fillers of the industrial mineral type that find extensive application in the paint and plastics industriesIn the paint industry, mineral fillers are known as extender pigments. Extenders are added to paint and plastic compositions to (1) lower the cost and (2) rein-force or modify the physical properties of a composition.Commonly used extenders are classified according to chemical type and discussed in terms of the change in physical properties that they impart to a paint or plastic film. Available cost reductions and data on the consumption of extenders in the Canadian paint industry are also included."

Jan 1, 1970

By G. Wren

As base metal sulphide resources become increasingly challenging to process, producers seek alternative options to treat concentrates. This study considers the mineral, elemental, and leaching character of a West Australian nickel sulphide deposit (Cosmos Nickel Project). After a brief review of the published work bench top leach tests were conducted to examine the factors which impact the kinetics of nickel sulphide leaching such as particle size, temperature, acid strength and type, concentration of copper sulphate and sodium chloride, and oxygen partial pressure. The effect of sodium chloride was considered due to the common occurrence of hyper saline water at West Australian nickel sulphide mine sites. Ultrafine grinding to an 80% passing size of 10 µm resulted in high nickel leaching efficiency. Moreover, higher concentrations of acid, copper(II) and sodium chloride also gave higher nickel and cobalt leaching efficiencies but arsenic precipitated as FeAsO4. Under the most suitable conditions the extractions of nickel, cobalt and arsenic at 90oC after 6 hours were >95%, 90% and <5%, respectively. The comparison with results from high pressure operations indicates the possibility of using a hydrometallurgical flowsheet based on fine grinding and atmospheric pressure leaching and warrants further investigations.

Jan 1, 2014

By Sidney Katell

This study estimates capital investment, operating costs, and selling prices for four underground bituminous mines producing coal with annual production ranging from 1.06 to 4.99 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of December 6, 1974, under the Bituminous Wage Agreement of 1974, and costs for material and equipment are based on 1975 indexes. Initial capital investment ranges from $20,799,800 for the 1 .06- million-ton-per-year (MM tpy) mine to $84,027,500 for the 4.99-MM-tpy mine. Total capital investment ranges from $32,506,800 to $1 22,983,500 for the same mines. Corresponding selling prices for the coal range from $12.87 to $11.64 per ton, assuming a 15-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1976

By Robert S. Williams

NO new ferrous alloys have been produced in the last five or six years that are as outstanding contributions to civilization as were the high-speed steels of the early part of the century or the stainless steels announced at the close of the World War. There have been, however, many developments of major importance having to do either with modifications of existing alloys or with new methods of treatment of older iron or steel alloys. Only a limited number of these new developments can be discussed and their selection does not necessarily imply that these are the most important but merely that they are of general interest rather than perhaps of greater importance in highly specialized fields.

Jan 1, 1939

By J. H. Rowland

The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) amended the Federal Mine Safety and Health Act of 1977 to improve the safety of mines. The MINER Act established a Technical Study Panel (the Panel) to provide independent scientific and engineering review and recommendations with respect to the utilization of belt air and the composition and fire retardant materials in underground coal mining (1). Because frictional heating is a common cause of belt fires, the Panel recommended that the Mine Safety and Health Administration (MSHA) evaluate the drum friction test to determine if such a test would contribute to conveyor belt safety beyond that provided by the Belt Evaluation Laboratory Test (BELT). This paper compares the results of the drum friction test to results from the BELT and large-scale tests for six different conveyor belts. The results are used to evaluate the drum friction test as a method to determine the fire resistance of conveyor belts.

Jan 1, 2011

By D. E. Stephenson. Discussion by R. G. K. Morrison, L. Obert

R. G. K. Morrison (Chairman, Dept. of Mining Engineering and Applied Geophysics, McGill University, Montreal, Que., Canada) - The discing of drill core has been a recognized pressure phenomenon for many years but only recently has an interest been taken in the mechanism involved. The work of Jaeger and Cook is referred to in the text. The authors have now advanced the study to establish, within certain loading limitations, a direct relationship between axial and radial stress at failure. This is an important contribution. In mines generally, where pressure conditions result in the spalling of openings, the faces of drifts and crosscuts, on scaling, usually show a concavity with respect to the opening very similar to the face of the drill hole after the separation of the stub. The same holds for shaft sinks. This suggests a similarity between the mechanism of the discing of core and that of the spalling of an opening, under pressure, to develop a more stable outline. The latter, commonly regarded as shear, is the most conspicuous type of failure observed in

Jan 1, 1967