Search Documents

By Lyman G. J

Magnetic separator operation in the recovery of magnetite in heavy medium circuits was studied by conducting a series of tests on a full size wet drum magnetic separator.The significant operational variables were found to be feed pan clearance, squeeze pan clearance, dry magnetite feed rate and separator drum speed. With feed and squeeze pan clearances optimized for typical primary separator operation, magnetite loss and concentrate specific gravity were found to be related in a regular manner to dry magnetite feed rate at any drum speed.A two component model of magnetite loss is proposed, relating total magnetite loss to losses in the feed pan and squeeze pan zones. The experimental curves relating magnetite loss to dry magnetite feed rate at the various drum speeds are interpreted in terms of the two component model.The magnetite particle size distribution in the separator was also examined. The tailings magnetite was found to be finer than the feed magnetite only when the dry magnetite feed rate was low, or immediately following the introduction of a new charge of magnetite when the separator was fed at an intermediate dry magnetite feed rate.

Jan 1, 1983

By David Siu

Many problems were encountered with the mechanical wedge-type splices used for the 15-inch square precast prestressed concrete piles installed at an industrial plant site. Many of the wedges were breaking during installation of the splices and after pile driving resumed following splicing. Dynamic monitoring of the piles and uplift loading tests confirmed that the problems were associated with cracked or damaged wedges. More ductile, annealed wedges were subsequently used, and, while not completely satisfactory, they were found to perform better than the original more brittle wedges. Introduction Long precast prestressed concrete piles were installed to support heavy, settlement-sensitive structures at an industrial plant in Port Alberni, British Columbia, Canada. The piles were driven through soft compressible silts and clays to toe bearing in a dense sand and gravel deposit or on bedrock. Each pile consisted of two or three segments joined with mechanical wedge-type splices trademarked DYN-A-SPLICE. Shortly after construction began, problems arose during pile installation, and these problems were, later, identified to be related to the wedges, or clamps, used to connect the splice plates.

Jan 1, 1991

By B. Y. Park

This paper develops a series of three-dimensional simulations for the Bayou Choctaw Strategic Petroleum Reserve. The U.S. Department of Energy plans to leach two new caverns and convert of one of the existing caverns within the Bayou Choctaw salt dome to expand its petroleum reserve storage capacity. An existing finite element mesh from previous analyses is modified by adding two caverns and increasing the size of existing Cavern 102. The structural integrity of the three expansion caverns and the interaction between all the caverns in the dome are investigated. The impacts of the expansion on underground creep closure, surface subsidence, infrastructure stability, and well integrity are quantified. The results show that from a structural viewpoint, the locations of the two newly proposed expansion caverns are acceptable, and all three expansion caverns can be safely constructed and operated.

May 1, 2009

By William Van Impe

A most renewing and promissing soil displacement screw pile is called the O-pile. The O-screw pile is a soil displacement auger pile based on a screwing in - screwing out procedure. The displacement auger head consists of a discontinuously diameter - increasing steel tip, on top of which the continuous screw flange with variable pitch is mounted. The soil displacement is kinematically ensured by downwardly oriented slots mounted on the auger head at different well chosen locations on the flanges. This leads to a very efficient lower energy screwing-in sequence of the pile and consequently to a high penetration rate. A test loading program of instrumented O-piles has been carried out in order to evaluate the load settlement behaviour, the shaft and tip capacity of the O-pile, including its specific installation parameters.

Jan 1, 1996

By P. Lenegan, R. Masethe, R. I. L. Ferreira

Underground mining in high rock-stress environments can induce unanticipated dynamic rockmass deformation, posing a serious risk to the workforce. Data collected by seismic networks are imperative for the design-as-you-mine process. Often an inappropriate assessment of the seismic hazard is done when unnecessary data are included in analytical techniques, particularly short-term time frames. Depending on the methodology or application of data analysis and interpretation, some of the information may not be relevant and even detract from the objective. By using the spatial event clusters associated with active workplaces to define the shape and size of the polygons for data selection for subsequent analysis, a problematic subjective component can be eliminated. The mining of tabular reefs in South Africa, be they gold- or platinum group metals, is very extensive, and underground workplaces are often widespread. Production stoppages are very costly, especially for marginal mines, so there is just cause not to evacuate an entire operation’s workforce following the occurrence of a large mining-induced seismic event. A rationale based on the damaging peak particle velocities (PPV) of the past seismicity can exclude the unaffected underground personnel and allow a quick orderly withdrawal where required. Micro-deformation may precede rockbursting, which can occur on-shift close to the workface. A mine-wide array of geophones suitable for the accurate location and analysis of seismicity may not be able to detect these higher-frequency emissions. Inexpensive but fit-for-purpose accelerometers, providing real-time, continuous measurement of acoustic rockmass deformation near the workplace, integrated through underground and surface communications networks, are shown to record ‘rock-talk’, clearly distinguishable from the instrument background noise, which can be in the order of hours leading up to an imminent damaging seismic event.

Jan 12, 2025

By R. G. Horvath

In the Hamilton area, and in many other areas of Ontario and around the world, large diameter drilled pier (caisson) foundations are frequently selected as the most appropriate foundation system for heavily loaded structures. Locally, these drilled piers are typically founded in competent glacial till or in the underlying shale bedrock depending on the anticipated design loads. Drilled pier foundations socketed into shale bedrock were selected for the Hamilton General Hospital Addition. The structural loads applied to socketed pier foundations are supported through shaft resistance, which is the shearing resistance developed along the vertical pier-rock interface, and by end-bearing resistance. The factors which control the load-displacement-time behaviour of socketed pier foundations are the strength and deformation characteristics of: a) the concrete pier, b) the rock mass, and c) the interface between the concrete pier and the rock.

Jan 1, 1987

By Michel C. Frippel

This section of the Minerals Yearbook reviews the minerals industries of 29 countries: the 12 nations of the European Community (Belgium, France, the Federal Republic of Germany (FRG), Italy, Greece, the Netherlands, Denmark/Greenland, Spain, Portugal, Luxembourg, The United Kingdom, and Ireland); 6 of the 7 nations of the European Free Trade Association (Sweden, Norway, Finland, Iceland, Austria, and Switzerland); Malta; the 8 Centrally Planned Economies of Eastern Europe (the German Democratic Republic (GDR), Poland, Yugoslavia, Albania, Hungary, Czechoslovakia, Romania, and Bulgaria); and the U.S.S.R. Western Europe Western Europe [loosely defined to include the 12 nations of the European Com-munity (EC) and the 7 nations of the European Free Trade Association (EFTA)] is the single largest trading area and consumer of raw materials in the world. If Western Europe was at one time an important mining sector, it has now increasingly relegated the role of supplying minerals for its minerals processing industry to its ex-colonies in North and South America, Africa, and Australia. In this regard, Western Europe is the most important determinant of raw materials consumption (and thus, indirectly, raw materials production). There is an important reason for this since Western Europe lies somewhere between Japan at one extreme and the United States and the U.S.S.R. at the other extreme as regards the availability of natural resources.

Jan 1, 1992

By D. M. Avant, A. J. Solomon, S. M. Pickering, W. R. Fox

Introduction Most high purity silica is produced from crystalline quartz, generally from sand. However, there is a small area of southern Illinois where a porous, friable white chert rock is found that is very different in physical form from quartz sand. This microcrystalline material, commonly referred to as tripoli, is more easily ground to micron sizes than sand. Although of similar Moh's hardness, microcrystalline tripoli is less abrasive than either ground quartz sand or many synthetic abrasives. Location The southwestern corner of Illinois is underlain by extensive deposits of very porous chert; in some places the material is quite white. Two companies, Illinois Minerals Co. and Tammsco Inc., mine and process this white material. The Illinois Minerals plant is located at Elco, and the Tammsco plant is in Tamms, IL. Both companies mine from various locations within a 10-mile truck haul of their plants. Production from this district has been continuous since at least 1915. Malvern Minerals Co. mines and processes a generally similar microcrystalline, friable novaculite near Hot Springs, AR. Geology The southern Illinois white tripoli area is on the southern flank of the Illinois Basin. The commercial silica zone is a facies of the Clear Creek chert of Lower Devonian Age. To the north, where it occurs deep in the basin, the Clear Creek is a siliceous limestone. In the mining area, thin overburden has allowed access by surface ground water, which has leached away the carbonate content and left a quite pure silica residue. Fossils characteristic of sea bottom deposition, such as brachiopods and trilobites, are occasionally encountered in mining. The structure of the mining area is poorly known, due to infrequent outcrops. Strata in most mines are inclined at dips of 5° to 20°. There appear to be occasional high angle normal and reverse faults, but these are seldom of any significance in mining. The friable white silica zone mined in the Clear Creek chert is overlain by dark brownish-red chert and siliceous shale. Exploration drilling to date has not encountered the base of the microcrystalline tripolitic zone. Chemical content Leaching by ground water solution has removed virtually all the carbonate from the original siliceous limestone. Impurities encountered are red to yellow iron oxides, aluminous clays, and occasional black manganese oxides. The silica has no detectable formula water. A typical chemical analysis and physical properties are listed in Tables 1 and 2. Mineralogy and crystallinity Southern Illinois friable tripoli appears amorphous under the polarizing microscope. No crystal structure and only occasional, vague, patchy anisotropism is evident. However, the material gives an excellent quartz X-ray diffraction pattern. Thus, so far as X-ray mineralogy is concerned, the material is clearly

Jan 12, 1986

By James S. Grichar

Interest in mergers in the nonfuel mineral industry developed when 5 were listed among the 50 highest valued mergers in the United States in 1981. This report presents a Bureau of Mines study of trends in merger activity from 1960 to 1979 and explores motives for mergers in the nonfuel mining and mineral industry. The objective was to determine precedent for or a trend toward the 1981 acceleration in merger activity and to examine certain financial motives for non fuel mineral mergers. Data indicate that the relative value of non fuel mineral mergers has grown since 1972 although the number of mergers has remained proportionate to historical trends for all mergers. Since 1974, the assets acquired in "large," nonfuel mineral firm mergers, those of $10 million or more, have comprised at least 93 pct of assets acquired. More nonfuel mineral firm mergers involved mineral companies as the acquiring firm than vice versa but mining and minerals firms acquired were of higher value than nonmining firms. A major motivation for mergers involving large mineral firms was the acquisition of assets at less than replacement costs. Univariate statistical testing, a methodology chosen for its applicability to the data, confirms this hypothesis while rejecting other financial motives. The remainder of the work is devoted to a discussion of suggested areas for future study.

Jan 1, 1984

By S. R. Knowles, R. J. McDonough

"The purpose of this paper is to introduce to the minerals processing marketplace a viable alternative to conventional mechanical agitation and pachuca airlift agitation. What follows is a brief introduction to the Atara Corporation and the fundamentals of how an Atara ""cannon"" mixer operates. The main body of the paper is concerned with the results of a study to evaluate the cannon mixer for a gold cvanide leach application. A brief summary of research and testing for other metallurgical applications is also presented.1. 1 THE COMPANYThe Atara Corporation is a privately owned Canadian company, headquarted in Dorval, Quebec. Its subsidiary, Atara Incorporated, located in Paramus, New Jersey services the municipal wastewater treatment market in the United States. Dorval focuses on industrial mixing applications in Canada and the US. The Atara Corporation provides design, engineering and specifications of agitators for mineral land other) processing applications. Fabrication of mixers is pursued in either Canada or the US, depending on the ultimate destination.Although Atara and its unique static in-tank mixer are relative newcomers to the mining industry, the cannon mixer has demonstrated its value over the past 20 years in municipal wastewater treatment services. In the past four years the Atara unit has been developed for industrial applications; the bulk of the development work has been for metallurgical applications. To-date the cannon mixer has been evaluated for mixing slurries in the following applications: nickel-copper concentrate storage, copper concentrate storage, coal slurry storage, gold cyanide leaching, uranium acid leaching, silver leaching and zinc acid leaching. Atara mixers have been installed with successful performance in full scale tanks containing nickel-copper concentrate slurry (Falconbridge) and gold cyanide leach pulp (Dome"

Jan 1, 1984

By John J. Sammarco

The mining industry has the highest average annual fatality rate among major U.S. industries. To address this, the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory (PRL), is conducting major research programs to reduce the hazard exposure of miners. One of the recently concluded programs at PRL developed the enabling technology for remote-controlled mining. An application involves the manual process of extracting and hauling coal where operators, in the tight confines of a mine, can be struck or caught by mobile machinery. The approach to remedy this problem uses a guidance system on the continuous haulage equipment so that it follows the continuous mining machine that extracts coal. This, in essence, involves sensor-based docking of the machines. Sensors functioning in the hostile mine environment of dust, methane gas, and water play the key role. Computer analysis of the mining machine's movements and empirical machine characterizations established operating requirements and spatial limitations to ensure proper loading of coal into the haulage equipment. These data served in the selection of a guidance sensor. Technologies such as scanning laser systems and ultrasonic sensors have frequently been used in other applications, but were found unacceptable. However, a near-infrared sensor employing active targets met the requirements. The sensor has a nominal 75b conical field of view and a range from 0.1 to 18.0 m. For the single-target mode, nominal range accuracy was 4.3% at a distance of 3.65 m. Correction algorithms were generated, which reduced the error to 0.6%. Airborne dust testing showed less than an additional0.8% accuracy (worst case) degradation at dust levels up to 15 mg/m3. Using four targets, the nominal range accuracy was 0.4% without correction algorithms. Analysis of dynamic testing of a continuous miner and haulage showed that accuracy was maintained and total target loss did not occur. A guidance system for the haulage system to follow the mining machine does not exist commercially. Such a system can reduce fatalities, injuries, and exposure to dust and noise.

Jan 11, 1998

Since the 1989 Loma Prieta Earthquake in the San Francisco Bay Area, the California Department of Transportation (CALTRANS) has accelerated seismic upgrading of their bridges. Many structures can be improved with the simple addition of hinge seat restrainers. Others require modification of column bents and superstructure to column connections. Often, footing retrofits are necessary, which require the addition of tension/compression elements (compression piling and tiedowns anchors) to resist overturning moments substantially larger than those originally used for footing design. These footing retrofits may include doweled reinforced concrete footing extensions or new pile caps which transmit forces to either driven steel or drilled concrete piles. In some cases, installation of these traditional piling elements is expensive, impractical or impossible due to: low overhead clearance, ground obstructions, high water table, noise or vibration sensitivity, or the inability to laterally expand the existing plan dimensions of the footing. In the latter case, one practical option is to attach small diameter drilled and grouted tension/compression piling elements (Pin Piles) to the existing footing. The footing may be strengthened with dowels and added concrete thickness or there may be a reduced shear span due to the installation of larger or jacketed columns. A reduction of elements is available with a Pin Pile alternative, particularly when the selection of traditional standard piles is governed by the reduced tension/uplift capacity available from the traditional elements, since Pin Piles exhibit superior uplift performance.

Jan 1, 1993

By M. I. Brasileiro

The use of experimental design to the study of mixtures has found a wide range of applications, even in laboratory scale or in industrial development works. The aim of this work was to maximize granite sawing waste content in ceramic tiles using experimental design. Based on the raw materials, specific formulations were developed using the experimental design. The raw materials were mixed and sample bodies were produced using uniaxial pressing. The sample bodies were fired and characterized in terms of water absorption, mechanical strength and X-ray diffraction. Regression models were adjusted relating the water absorption and mechanical strength with the amount of raw materials. The results showed that the methodology of experimental design maximize the content of wastes incorporated in ceramic tiles formulations. Formulations containing up to 40% of waste can be used for the production of ceramic tiles.

Jan 1, 2009

By Sang Ho Cho, Masaji Kato, Masaaki Yamamoto, Masaaki Nishi, Katsuhiko Kaneko

This paper presents a numerical simulation method to predict rock fragmentation and to verify a fracture mechanism by bench blasting. The rock fragmentation, which has been used as a means of the index to estimate the effect of bench blasting, affects the expenses for loading, conveyance and crushing of blasting muck piles. The developed numerical simulation method is based on the finite element method and fracture mechanics and includes the re-meshing procedure to express the fracture process of the rock mass. This paper discusses a procedure for a determination of size distributions of the results, which were calculated by numerical simulation, including the tines.

Jan 1, 2002

By Luis Bernal, Pertti Lamberg

"SkimAir®, Outotec’s Flash Flotation unit, is placed in the grinding circuit to float the valuable liberated mineral particles from the circulating load of the grinding process while still relatively coarse. Esperanza copper-gold deposit located near Sierra Gorda, Chile, hosts 535 Mtn ore grading 0.57 % copper, 0.27 g/t gold. A series of laboratory and pilot flotation tests were conducted to find out the flotation performance of different ore types both with and without the Flash Flotation. This data was used in modeling and simulating to find the optimal flow sheet for the highest Au and Cu recoveries with required Cu concentrate grade. Simulations with the HSC Chemistry 6.1 software showed that with the SkimAir® and Flash Cleaning it is possible to achieve the required copper grade of 27% Cu with 5% higher recovery for gold and 2% higher recovery for copper compared to the circuit without the Flash Flotation. The pilot tests with simulations were the back up for the installation of four Outotec SkimAir® SK 2400 Flash Cells in the Esperanza circuit for the processing 95.000 tpd of copper-gold ore.INTRODUCTIONEsperanza copper-gold deposit is located near the town of Sierra Gorda, 2nd Administrative Region in Chile. Deposit hosts 535 Mtn ore grading 0.57 % copper, 0.27 g/t gold. The main copper minerals are chalcopyrite and bornite. Gold is carried by native gold and solid solution of copper.Antofagasta Minerals S.A. conducted a series of flotation studies at SGS Minerals Services. The studies included both laboratory and pilot scale work. In the pilot scale study the applicability of the Flash Flotation technology was studied with High-grade Andesite and High-grade Porphyry samples (SGS Mineral Services). The Flash Flotation technology gave significantly higher recovery for gold than the conventional flotation circuit. The recoveries for copper were slightly higher using the conventional flotation."

Jan 1, 2009

By Paul C. Schmall

The link between artificial ground freezing and the mining industry stretches back more than 140 years, and across an ocean. Patented by the German scientist F.H. Poetsch in 1863, the technique is reported to have first been used circa 1862 in the coal mining valleys of South Wales. In the United States, the first ground freezing application, to a depth of 30 m (100 ft), occurred in 1888 for the Chapin Mine Co. in Iron Mountain, MO. In England in 1901, the Poetsch method was used for the first time to successfully sink two shafts through 24 to 27 m (80 to 90 ft) of wet sand and boulder clay at the Washington Glebe Colliery, near Sunderland. British mining engineer T.H. Cockin, in his 1905 Class-Book of Practical Coal-Mining, noted that, ?This method of sinking through thick beds of very wet quicksand has met with great success; it is one of the recognized methods of sinking on the Continent.? Mine shaft freezing soon became relatively common in Europe where the project could bear the cost of a major refrigeration plant construction. However, it was not until 1952 that the second North American ground freezing project was completed to facilitate the sinking of a 4.5-m- (15-ft-) diameter, 233-m- (765-ft-) deep shaft at a Potash Company of America (PCA) mine in Carlsbad, NM. Nowadays, ground freezing is used worldwide for both mining and civil applications. In small mine shafts of 3 to 6 m (10 to 20 ft) in diameter, excavations have been carried out to depths of more than 820 m (2,700 ft) within the protection of unbraced or unlined frozen walls. In fact, for deep mines, no better method has yet been established for sinking production shafts through deep, water-bearing ground. Major deposits of coal, potash and salt would still be inaccessible if not for artificial ground freezing. There are several advantages of ground freezing unique to the construction of shafts. Proper instrumentation can provide complete assurance of the integrity of the freeze to full depth prior to excavation. The frozen wall allows construction to be scheduled without evaluating the in-shaft time necessary to probe ahead, place additional sup-ports or deal with ground water. The freeze can be implemented perfectly through the soil/rock interface, which is often the most difficult geology in which to create a ground water cutoff by other methods. At increasing depths, any discontinuity

Jan 1, 2007

By P. F. Sands

This U.S. Bureau of Mines report reviews the state of the art in blind pneumatic stowing of backfill in voids in abandoned coal mines. It contains a short history of the development of pneumatic equipment in mining and four recent case histories of blind pneumatic stowing. Limitations of pneumatic stowing in terms of equipment wear, costs, backfill material, and methodology are discussed, and some new procedures and designs are reviewed. A bibliography covering pneumatics in mining is included also. This report provides background for the preparation of a Bureau test program in which the variables affecting the efficiency of pneumatic backfilling will be studied using a full-scale surface test facility.

Jan 1, 1990

By B Saunders, J Carpenter

PanAust’s Phu Kham copper-gold operation (Phu Kham) in Laos is currently limited by throughput in the Semi Autogenous Grinding (SAG) mill. The ability to accurately predict SAG mill throughput (throughput) is therefore critical to accurately forecast copper and gold production. During the fourth quarter of 2016 the proportion of hard unweathered rocks in the mill feed increased, resulting in a period of lower than expected throughput. These low throughput rates prompted a study with the aim of identifying a practical solution for throughput predictions. The study identified an empirical modelling approach based on actual SAG mill throughput rates. The empirical model was then optimised by linear programming to identify the ideal feed blend of unweathered rocks to achieve a maximum SAG mill throughput.Rock strength was the initial focus of the throughput study at Phu Kham because previous studies had identified a strong link between rock strength and throughput. It was determined that there was insufficient valid data to adequately model but sufficient data to qualitatively characterise rock strength. The data identified that the weathering and lithology had a controlling influence on the rock strength. Complicating throughput predictions were operational improvements (changes to blasting and mill settings) implemented in response to the lower than expected throughput. This created uncertainty with the throughput equations. A self-learning empirical modelling method was developed to predict the throughput by incorporating fundamental rock properties with operational practices and improvements. The method is based on the proportion of mill feed with similar weathering and lithology (a proxy for comminution performance) and the actual mill throughput using the SAG mill as the analytical instrument. The modelling method simultaneously incorporated the sum and interaction of unmodelled influences including blasting, crushing and mill settings. The empirical modelling method worked at Phu Kham because the lithology and weathering has an intuitive and observable controlling influence on SAG mill throughput. The modelling method is described along with a worked example of feed blend optimisation using linear programming.CITATION:Carpenter, J and Saunders, B, 2017. Empirical mill throughput modelling and linear programming for blend optimisation at the Phu Kham copper-gold operation, Laos, in Proceedings Tenth International Mining Geology Conference 2017, pp 291–296 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By John Dasher

In 1980, some US cars were designed and built to metric dimensions; wine and gas were sold by the liter; and the March of Dimes Walkathon was measured in kilometers. Although the US Congress has taken a ''soft" approach to metrication, and public resistance to the idea remains strong, the use of metric units is becoming more and more widespread. As the minerals industry becomes more international in scope, US mining companies are converting to the metric system-particularly those companies with business interests overseas.

Jan 2, 1981

By James J. Graham

Uravan, Ambrosia Lake, Gas Hills and South Texas are all historic names in US uranium. These mining areas supplied the uranium that brought the United States into the nuclear age during the 1960s, and fueled the birth of nuclear energy for peaceful uses — a promise of nearly limitless, clean energy for the world’s future. That promise still exists today, but it is hard to hear over the rhetoric of environmental activists and politicians. Nuclear power offers dependable electricity with limited environmental impact at stable prices. Nuclear power releases no greenhouse gases or particulate matter into the atmosphere. High level nuclear waste (HLW), although long lived, is readily controlled and compact. In the United States, generating 1 billion kWh of electricity with coal produces 47 kt (52,000 st) of solid waste (ash and sludge), compared to 3.6 t (4 st) of HLW produced by nuclear.

Jan 1, 2002