Search Documents

By David E. Albus, Ahmadreza Mortezaie, Bidjan Ghahreman

The structural evaluation of seismic performance of an existing hospital in Long Beach, California, required spring constants of foundation elements. The structure included support by deep foundation elements comprised of belled (underreamed) caissons. The available relationships in the governing building code (ASCE41-13) to compute axial stiffness is not applicable due to the belled configuration of the caissons. The large diameter of the bells required consideration of the foundation medium to the axial stiffness; a detail not clearly described in ASCE 41-13. Furthermore, prescriptive equations in ASCE 41- 13 used to estimate lateral stiffness only consider pile groups with the assumption that the only source of lateral stiffness is the axial reaction of individual piles. These assumptions were invalid for the project at hand where all caissons are configured as single foundation elements, not a pile group. In the present work, the approach taken to estimate seismic stiffness of single-belled caissons is described which accounts for the elastic behavior of the foundation medium below the bell base and lateral behavior of single-pile shafts. Results of the work provide a more satisfactory derivation of the spring constants consistent with current modeling methods. INTRODUCTION Seismic evaluation of an existing hospital in Long Beach, California, required geotechnical investigation followed by site-specific ground motion analysis. This evaluation was required by the Office of Statewide Health Planning and Development (OSHPD) in order to meet the requirements of the Structural Performance Category 4D (SPC-4D) published as a part of the 2016 California Building Code, CBC (Section 3412A). SPC-4D utilizes ASCE41-13, as modified by OSHPD, and involves two seismic performance objectives: BSE-1E (20% probability of exceedance in 50 years) and BSE-2E (5% probability of exceedance in 50 years). Spring constants and capacities of foundation elements were needed for evaluation of the structural performance of the building subjected to these two performance objectives. Our review of the as-built foundation plans indicated that both shallow footings and caissons were used for support of the structure. The plans demonstrated that all caissons are belled (under-reamed) and are individual, i.e. not part of pile groups. In this paper, the subject site condition and foundation elements are described first. This is followed by details of assessing spring constants and vertical capacities for belled caissons. The new requirements of the 2016 CBC concerning the evaluation of critical facilities will likely entail evaluation of other structures with belled caissons due to the more extensive use of these foundations in the past. This paper proposes a method to address the conditions of individual belled caissons not explicitly considered in the current code provisions.

Jan 1, 2018

By José E. Rondoña

El presente trabajo desarrolla un estudio comparativo de la producción de dos tipos de hornos usados en la fundición de cátodos de zinc en la planta de La Oroya, para asi determinar cúal es el equipo más idóneo para futuras expansiones del proyecto. De los puntos comparativos se encontró que el horno SICE desarrolla más productividad de personal en operaciones, así como en el rendimiento de la energía eléctrica. Mientras que respecto de las consecuencias de las filtraciones del metal, se encontró que el horno Ajax es el más adecuado, dado que la producción de barras se afecta solo en la producción que el horno afectado representa en la instalación total. Por ende, es conveniente el uso de dos hornos SICE tamaño mediano dada la capacidad y productividad de esta.

Nov 20, 1967

By P Lindsay

A numerical model has been developed to simulate the effectiveness and costs of a number of conceptual remedial measures aimed at reducing acidity and metal concentrations in the Ngakawau River and its tributaries near the Stockton Coal Mine, situated on the West Coast of New Zealand. The Stockton Coal Mine has been in operation over the past 100 years. During that time, seepage from waste rock dumps has contributed to elevated acidity and metal concentrations in the Ngakawau River and some of its tributaries. The yearly mean rainfall at the mine site is 6000 mm. The model, developed using GoldSim software, simulates rainfall, run-off and stream discharge for 26 tributaries. It then calculates acidity and metal concentrations in the mine impacted tributaries and the dilution downstream from the mine. The model has been calibrated to measured flow and acidity and metal concentrations in the Ngakawau River and some of its tributaries. Acidity and metal loads are removed from the system in accordance with specified efficiencies and capacities of the respective conceptual remedial measures. The user can compare specific remedial measures, or a combination of conceptual remedial measures. The model predicts the acidity and metal concentrations at a number of monitoring stations for any remedial strategy selected by the user. It also calculates the capital and operational costs for that particular remedial strategy. This paper presents the development of the numerical model and describes how the end-user can use it to compare the efficiency and costs of various remedial strategies by running different æwhat ifÆ scenarios.

Jan 1, 2006

By Xuejing Xie, Tianxiang Ren

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). Standardised stream-sediment sampling procedures have been used in mountainous and hilly terrains. Special sampling procedures were developed for application in remote environments, such as high mountains, desert, semi-desert, karst and loess-covered regions. The diversified analytical methods used in more than 20 analytical laboratories participating in the project have been unified into two multi-element, multi-method analytical systems. A unified data monitoring procedure was developed based on primary and secondary standard samples. To date the project has covered about 4 000 000 km2 and the aim is to complete the coverage within the present decade

May 1, 1991

By J. Mcdvcka

Sustainable development has become a driving imperative for the resource industry as it is for the rest of the global business world. Being unsustainable is a risk no business can afford. Yet implementation of sustainable development practices beyond satisfaction of compulsory reporting is still sporadic. The current standard approaches to problem analysis and decision making are too narrow to capture the complexity of the issues at stake. Hence it is necessary to develop innovation in thinking and in doing. Those who search for ways to implement sustainable development use concepts such as Whole Systems Thinking and Eco-efficiency as well as tools like Life Cycle Analysis. Others develop their own instruments. In their effort to innovate they face both resistance and support within their organisation as well as within the industry or the wider context. This paper explores the factors that support, hinder and shape the sustainable development drive of the industry and proposes a comprehensive decision-making framework that links the goal of sustainability with the tools of sustainable development. This exploration is illustrated by a case study used in a doctoral research conducted on an engineering firm providing services to our industry.

Jan 1, 2007

By Klaus Hasselwander

Fluctuating SO2 gas streams represent a difficult task for designers of SO2 removal systems (with respect to designing the plant), but in spite of the designers great efforts to solve the problems, the operation of such plants requires much care and attention. A fluctuating gas flow usually results from metallurgical smelting processes. Both gas composition and gas flow rate may vary. The first part of this paper outlines some existing technical solutions and presents the Pros and Cons of the different solutions. These solutions outline are: - Sulphuric acid plants operated with a preheater permanent in operation - Sulphuric acid plants with concentration increase of SO2 gas either using regenerative SO2 removal or cryogenic partial condensation of the SO2 - Sulphuric acid plants with additional burning of sulfur to increase SO2 content - Single-stage sulphuric acid plants followed by a tail gas system (which is) designed for periods of low SO2 input In the second part, this paper describes some existing technical solutions for removal of SO2 at low concentrations (i. e. less than 0.1 - 2 %-by volume), which could be used as tail gas treatment system for acid plants. While selecting an appropriate solution, special attention should be given to operating costs, which usually to a large extend depends on the type of absorption agent and the costs for disposal of the sulfur compound produced.

Jan 1, 2009

By Syd Peng, Gamal Rashed

"Bumps in coal mines have been recognized as a major hazard for many years. These sudden violent failures around mine openings have compromised safety, ventilation and access to mine workings. Previous studies showed that the violence of coal specimen failure depends on both the interface friction and width-to-height (W/H) ratio of a coal specimen. The mode of failure for a uniaxially loaded coal specimen or a coal pillar is a combination of both shear failure along the interface and compressive failure in the coal. Unstable interface failures provide a sudden de-confinement to coal rib, thus triggering uns and compressive failure in the sidewalls. The compressive failure of a coal specimen or a coal pillar can be controlled by changing its W/H ratio. As the W/H ratio increases, the ultimate strength increases. With a proper combination of interface friction and the width-to-height (W/H) ratio of pillar or coal specimen, the mode of failure will change from sudden violent failure, which is brittle failure to non-violent failure, which is ductile failure. The main objective of this paper is to determine at what W/H ratio and interface friction the mode of failure changes from violent to non-violent. In this research, coal specimens of width-to-height ratio ranging from 1 to 10 were uniaxially tested under two interface frictions of 0.10 and 0.25. The results are presented and discussed.INTRODUCTIONCoal mine bumps are sudden, violent bursts of coal from a pillar or pillars or a block of coal, resulting in a section, the whole pillar, or the solid block of coal being thrown into an open entry. These bursts are accompanied by very loud noises (Peng, 2008). Several case histories in mining have long described coal pillars or coal faces failing violently with an accompanying ejection of debris and broken material into the working areas of the mines (Campoli et al., 1987; Osterwald, 1962; Peperakis, 1958; Garvey et al., 2013). Because of the catastrophic nature of these sudden failures, understanding the causes of coal mine bumps is essential to create a safe underground working environment. This phenomenon has motivated many ground control researchers to conduct extensive field investigations throughout the past century. Rashed and Peng (2014) compared the mechanical properties of two kinds of coal, one from bump and the other from non-bump-prone mines. They found that coal itself does not play any significant role in coal bumps and recommended that future research should focus more on the local variation of geological conditions such as the interface friction between pillar and roof and between pillar and floor."

Jan 1, 2015

By R. W. Nice

Presently about 60% of the world's nickel resources are tied up with lateritic ores while about 25% of the world's nickel is produced from sulphides. Based on this the industry has to focus on improving lateritic nickel economics in order to maintain the high use of the metal worldwide. In 1997 three junior mining companies in Australia organised finance against all odds and commenced development of three separate nickel and cobalt extraction plants treating lateritic nickel ores. All three projects utilise similar pressure acid leaching (PAL) technologies while each has unique metal recovery technologies All projects have experienced numerous processing and maintenance related difficulties such that full ore throughput has been reached by only one operation after five years. This shortfall in performance has caused the owners considerable angst and financial pain. In 2000 Cawse went into receivership and was purchased by an international corporation. Recently, Bulong also went into receivership and has undergone an orderly shutdown, awaiting sale to a new buyer. Murrin Murrin has settled with its financiers and is in a position to operate as planned for many years forward. This paper will discuss a number of the technical difficulties that affect the ore preparation, PAL and solution treatment circuits of these plants. The objective is to identify the cause of some of the difficulties and propose possible solutions so that the next generation of lateritic operations can emerge as technically and, more importantly, economic successes. A number of these process improvements have been identified by the existing operators and in many instances have been or are being implemented into the existing operations.

Jan 1, 2004

By B. J. Moore

This publication contains routine analyses and related source data for 528 natural gas samples from 21 States collected during calendar year 1965 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the' Bureau of Mines since 1917. The analysis published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4

Jan 1, 1966

By B. J. Moore

This publication contains routine analyses and related source data for 528 natural gas samples from 21 States collected during calendar year 1965 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4

Jan 1, 1966

By Arthur L. Holloway, James C. Mugford

"The Underground Research Laboratory (URL) is located in southeastern Manitoba, in the Lac du Bonnet granite batholith of the Canadian Shield. It was constructed by Atomic Energy of Canada Limited (AECL) to conduct geotechnical research for the Canadian Nuclear Fuel Waste Management Program, assessing the concept of permanent disposal of nuclear fuel waste deep in plutonic rock.One of the primary objectives of the research program at the URL is to develop a nondestructive rock mass characterization method that can be used during siting, design and construction of a used fu el waste disposal vault. An experimental program was established to assess radar reflection profiling as a technique for fracture characterization in granite. The highly resistive, homogeneous nature of the Lac du Bonnet granite is ideal for the propagation of electromagnetic energy at the radar range of frequencies and water-filled fracture zones act as excellent reflectors because of their contrasting electrical properties.Radar reflection profiling was undertaken to characterize a major fracture zone located between 5 m and 10 m below Room 211 on the 240 m level of the URL. The profiling was done at a frequency of 120 MHz, on a 1m grid laid out on the bare rock floor of the room. Reflectors identified in the analog data were correlated between the profile lines, digitized, and a three-dimensional surf ace for each recognizable reflector was constructed. These surf aces were then compared with data obtained from the examination of numerous cores from adjacent boreholes intersecting the fracture zone. A very good correlation was found between the major radar reflectors and the most intensely fractured regions of the zone. Modelling studies also showed that a series of prominent shallow radar reflectors were caused by a borehole drilled close to Room 211."

Jan 1, 1990

By W. W. Agey

Past investigations on waterborne impurities in the flotation process have been concerned primarily with the treatment of specific ores with particular local waters. Although some anions and cations present in water are known to react with flotation reagents, a definitive study has not been made on the effect of such common ions upon the flotation process. This report describes the fundamental research undertaken to define and measure the adverse and/or beneficial effects of different concentrations and combinations of several common anions and cations when oleic acid is used to froth-float limestone from a pulp of quartz and limestone. Research on the effect of waterborne impurities upon the flotation process was composed of two equally important phases. The first phase comprised development of a procedure for floating limestone from quartz that would give the same results in test after test. Some difficulty was encountered, but once such a procedure was developed, the second phase, comprising study and measurement of the effect of various ions c on to natural water upon the flotation of limestone, was quickly completed.

Jan 1, 1963

By E Selvapandian, R Barr

Arrium (previously OneSteel) initiated a desktop study into the performance of its hematite ore beneficiation plant in early 2010. The beneficiation plant utilises jig concentrators and spirals to upgrade low-grade hematite recovered during mining at the Iron Duke (ID) mine site located 60 km south-west of Whyalla. The study, conducted in conjunction with Mineral Technologies, identified a number of opportunities for improvement, which were validated by a series of sampling campaigns and a pilot plant trial. One of the major recommendations was to upgrade the ultra-fines processing circuit from a single-stage spiral circuit to a three-stage circuit. The upgrade of the ultra-fines circuit was estimated to provide a significant increase in fines production and grade.In order to capitalise on the strong iron price at the time of the project, Arrium decided to utilise a fast-tracked approach to design, construct and commission the processing equipment required to achieve the improvements identified. This decision introduced the risk of missing critical steps in the project development process, which could have potentially resulted in major issues in latter stages of the project. In addition to the challenges introduced due to the expedited time line for project completion, this project presented unique challenges due to its brownfield nature. One such challenge faced was the integration of the new equipment and control system software.Furthermore, the importance of the ID ore beneficiation plant (OBP) contribution to the companyÆs export commitments meant the upgrade work had to occur while minimising disruption to normal operation. This decision presented a set of new challenges to an already complex project. One such challenge was the need to build and commission the new spiral circuit in isolation from the operating plant.The aim of this paper will be to highlight some of the challenges faced in a complex brownfield project such as the ID OBP upgrade and discuss how they were managed to enable the successful commissioning of the process in early 2012.CITATION:Selvapandian E and Barr, R, 2013. Managing challenges faced in the brownfield commissioning of an ultra-fine hematite processing circuit at ArriumÆs Iron Duke ore beneficiation plant, in Proceedings Iron Ore 2013 , pp 533-538 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Zhan Jing

Keywords: thermodynamic, Ni-Co alloy powders, composition, fibrous The mathematics model of Ni(II)-Co(II)-C2O42?-NH3?H2O-H2O of thermodynamic equilibrium system has been developed theoretically according to the law of conservation of mass and the law of simultaneous equilibrium, and the logarithm concentration-pH (log[Me2+]T-pH) diagrams of this system have been made. The effect of ligand and pH value was studied. Two issues in coprecipitation route to synthesize fibrous nickel-cobalt alloy precursor powder, com-position and morphology which are a first priority, are addressed based on thermodynamic analysis and experiments. The results show that suitable pH value range of coprecipitation of nickel ions and cobalt ions in theory can be obtained to maintain fibrous, excellent compositonal homogeneity and stoichiometry in coprecipitation products. Experimental demonstration is also carried out.

Jan 1, 2005

By Claudeir Carvalho Silveira

A necessidade da indústria automobilística de redução de peso, desenvolvimento de designs arrojados e aumento da resistência a corrosão dos automóveis obrigou as indústrias siderúrgicas a produzirem aços galvanizados de alta resistência. Entretanto, para que haja este desenvolvimento é necessário maior conhecimento do comportamento dos revestimentos galvanizados quando submetidos a processos de estampagem. Desgastes da superfície galvanizada, formação de pós, redução da resistência a corrosão e atrito das superfícies são aspectos importantes a considerar no projeto do ferramental de estampagem. Este trabalho teve, portanto, como objetivo a avaliação do efeito dos revestimentos Galvanizing e Galvannealed no coeficiente de atrito de um aço Dual Phase 600. Para avaliação do coeficiente de atrito foi utilizado um tribômetro de ferramenta plana que simula o atrito na estampagem de peças. O trabalho apresenta ainda a caracterização microestrutural do revestimento realizada por microscopia ótica (MO) e eletrônica de varredura (MEV) e espectroscopia de energia dispersiva (EDS). Para avaliação das propriedades do substrato e do revestimento foram utilizadas também medidas de Microdureza. Após a realização dos ensaios, foi caracterizada ainda a evolução dos revestimentos após desgaste promovido pelo tribômetro de ferramenta plana e a identificação e caracterização do fenômeno de stick-slip.

Aug 8, 2018

By Thomas M. Barczak

The 1990s brought an unprecedented increase in the development of innovative technologies to provide more effective and easier-to-install roof support in underground mines. To facilitate the application of these technologies in improving mine safety, the National Institute for Occupational Safety and Health (NIOSH) developed the Support Technology Optimization Program (STOP). STOP is a Windows-based software program that provides mine operators with a simple and practical tool to make engineering decisions about the selection and placement of these various roof support technologies. The program includes a complete database of the support characteristics and loading profiles obtained through safety performance testing of these supports at the NIOSH Safety Structures Testing Laboratory. A support design criterion in the form of the required support load density at a specified convergence can be established from four options: (1) a database of measured ground reaction obtained from various mines or ground behavior information input by the user,(2) load requirements based on a detached roof block or rock failure height, (3) criteria based on the current roof support system, and/or (4) arbitrary criteria set by the user. Using these design criteria, the program will determine the installation requirements for a particular support technology that will provide the necessary support load density and convergence control. Optimization routines are also available to determine the most efficient support design for a user-specified support installation. In addition to these performance measures, STOP can be used to compare material handling requirements and installation costs. Comparisons among the various support technologies are easily made, including a graphical analysis of relevant support parameters. This paper describes STOP and its application to optimizing standing secondary roof support systems.

Jan 10, 2000

By Walter D. Holland

This study was undertaken to determine miners' breathing zone concentrations of diesel exhaust components, to investigate any relationships between these concentrations and vehicle type, the presence of emission controls, vehicle usage, and ventilation conditions, and to make recommendations for monitoring and ventilation requirements. Twenty-four mines including two con l mines were surveyed. Sampling was done for CON, NON, SOx, PNA, aldehydes, and particulates. hi most mines, concentrations of at least one contaminant exceeded one half the standard or TLV. The concentrations of gases arc probably sufficiently reduced by a minimum air velocity of 50 fpm. A sufficient reduction of particulate concentrations may require as high as 400 fpm air velocity. Vehicle age, type, or usage appear to have little or no effect on contaminant concentrations. PNA levels were below detection limits in all but a very few samples. Minimum requirements for routine monitoring should include formaldehyde, COx, NO2. It is further recommended that better definition of the minimum ventilation requirement be obtained.

Jan 1, 1978

By Jay Rodgers

There has been a longstanding acceptance that burden plays a major role in the magnitude of ground vibration amplitudes generated from surface blasting. Much of the data that this belief is based upon is empirical in nature and may or may not represent an example of false inference. Recent published reports have rightly questioned the influence of burden and confinement on blast vibration amplitude, suggesting that the fracture condition of the rock mass is a better indicator. The increased investment in electronic detonators as a tool to control ground vibration amplitudes demands an understanding of vibration production detailed enough to make use of the vastly improved timing accuracy that they provide. A more accurate relationship may be found if we strip away the assumptions of the past and search for the underlying mechanism of vibration production in surface blasting. We must answer the question: What happens at or near the borehole when an explosive charge detonates that produces ground vibrations?

Jan 1, 2003

By G. R. Hopkins, A. B. Coons

A survey of the petroleum pipe lines by the Bureau of Mines as of May 1, 1923, shows that on that date there was a total of slightly more than 90,000 miles of pipe lines in the United States, having a capacity of approximately 15,750,000 barrels, which is equivalent to one-fourth of the nation's average production for one month. These lines varied in diameter from 2 to 16 inches, the weighted average being 6 inches. The total pipe-line milenge was about equally divided between trunk lines and gathering lines, though the capacity of the former was about four times that of the latter. This was due, of course, to the difference in average diameter, that for the former being 7.4 inches as compared with 3.7 inches for the latter. The common size for trunk lines was 8 inches, and for gathering lines 2 inches. Oklahora, with 19,180 miles of pipe lines, is the leading State in total mileage, with Texas second and Pennsylvania third. From point of trunk lines alone Texas is considerably ahead of any of the other States, a position which it owes to its size and to the growth in the rovement to its Gulf ports. Cali- fornia, though the leading State from point of production, ranks only seventh in pipe-line mileage. This is due to the fortunate location of the Los Angeles Basin fields, some of which are within sight of the refineries to which their oil is delivered or of the port of San Pedro through which their oil is shipped. The last survey of this nature, made in the spring of 1924 by the U. S. Geological Survey, recorded a total mileage of nearly 83,000 with a capacity of approximately 14,450,000 barrels. This indicates an increase of 9 per cent in both mileage and capacity during the two years.

Jan 1, 1927

By H Esterhuizen

The Ernest Henry Mine (EHM) in Queensland, Australia is a Sub-level Caving operation that started production below the previously mined open pit at a depth of 535m. Current Production mining has progressed to a depth of 730m, with planned production mining to extend down to at least 1000m below surface. The inclined nature and geometry of the orebody combined with geological structures provides for challenging mining conditions. Over several years, Ernest Henry Mine has introduced measures to improve outcomes based on observations, monitoring and data analysis. As mining progresses deeper, EHM will continue to proactively take steps to ensure future outcomes are anticipated and mining can continue safely and uninterrupted. The focus of this paper is on the changes in seismic- and stress-driven behaviour of the rockmass experienced at EHM, the ground control measures implemented, and the anticipated future conditions and controls required. CITATION:Esterhuizen, H, 2018. The evolution of seismicity and ground control measures at Ernest Henry Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 20–41 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018