Search Documents

By Joram M. Amir, Ernst Niederleithinger, Nikolaus Schneider

"Abstract: Diaphragm walls are used to provide a stable and watertight confinement for the construction of tunnels, underground railway stations, deep basements and other structures requiring deep excavations. Water seepage and soil loss through the joints have occurred on several occasions, causing extensive damage. This may have been due to uncontrolled concrete flow between the joints, unexpected geologic conditions or just poor workmanship.Different ways of quality assurance are applied on construction sites. Most of them rely on recording parameters of the construction equipment and conventional concrete quality control. In the frame of the EUREKA/ZIM project DiWaQ we have looked at several ways to perform non-destructive quality control. Some methods are to be applied after excavation before concreting (phase 1); others after the wall is completed (phase 2).For phase 1 we have used two different principles for checking the shape of the excavation, especially the joint to existing panels. A mechanical device which can be adapted to the excavating equipment was developed; field tested and validated on test and construction sites. It is described in detail in another paper in the same volume. A sonar-based device with a 10 mm resolution has shown good performance in the lab, but is still under development.For phase 2 different temperature sensors have been lowered into access holes to monitor the hydration heat developed during concrete curing. The same tubes can also be used to perform electromagnetic and ultrasonic crosshole measurements across or along joints to detect flaws. Especially the ultrasonic method has shown promising results on validation specimen at the BAM test site at Horstwalde, but limitations as well. Success substantially depended on the joint type, flaw size and distance of the sensors to the joint."

Jan 1, 2014

By T. Holmes, S. Davison

"A surge bin at Agrium’s Vanscoy potash operations has been plagued with flow, wear, and corrosion issues since being built in 1967. The culprits? The bin’s carbon-steel construction, geometry, and the resultant funnel-flow pattern are the root causes. An investigation and cost analysis indicated that hopper redesign and retrofit would increase production and reduce maintenance and capital costs. The retrofitted bin provides safer, more reliable operation and has a much longer predicted working life. Using this example, the authors describe bulk-solids-flow theory and highlight the importance of customizing bulk-material-handling-system design using appropriate flow properties to improve reliability, safety, and cost effectiveness.RÉSUMÉ Depuis sa construction en 1967, un réservoir intermédiaire de l’exploitation de potasse Vanscoy d’Agrium connaît des problèmes de débit, d’usure et de corrosion. Les responsables ? La construction en acier ordinaire du réservoir, sa géométrie et la structure de débit en résultant au niveau de la carotte en sont les causes fondamentales. Une étude et une analyse des coûts indiquaient que la restructuration et la rénovation de la trémie permettraient d’augmenter la production et de réduire les coûts d’entretien et en capital. Un réservoir rénové permet de renforcer la sécurité ainsi que la fiabilité de l’exploitation, et sa durée d’activité prévue en est augmentée. En se fondant sur cet exemple, les auteurs de l’article décrivent la théorie du débit de matières solides en vrac et insistent sur l’importance de personnaliser la conception du système de manutention des matériaux en vrac à l’aide de propriétés rhéologiques adaptées afin d’améliorer la fiabilité, la sûreté et la rentabilité.INTRODUCTIONIn early 2013, Agrium’s Vanscoy Potash Operations (VPO) engaged Jenike & Johanson Ltd. (J&J) to provide testing, consulting, and structural engineering services related to proposed modifications to the 270 t special standard product surge bin, which Agrium planned to undertake during a two-week shutdown in August 2013. The bin, which had been plagued with flow, wear, and corrosion issues for its entire working life, was essential for the continuous operation of two of VPO’s compaction plants and for efficient dispatching to loadout. The bin often experienced product hang-ups, clumping on the walls, and plugging at the hopper outlet. Two recent unscheduled mill shutdowns had been partially attributed to flow issues in the bin due to clumping and product plugging up at the screws. These problems increased maintenance costs, limited production capacity, and degraded product quality. Holes and paper-thin sections in the bin walls discovered during a 2013 inspection revealed the potential for major hot material leaks or even structural failure. Either issue would stop plant operations until the bin could be repaired or bypassed. Clearly, the bin cone had reached the end of its life and required replacement."

Jan 1, 2018

By G. M. Carrie

Introduction The subject of basic refractories is daily becoming of increased importance in metallurgical processes, and there is a constantly growing necessity for the development of better materials. This fact, together with the realization that Canada possesses one of the best sources of such refractories in the British Empire, if not in the world, made it appear? advisable that the subject be presented to the Empire Mining and Metallurgical Congress at the 1927 meeting. Having been in close touch with developments in the Canadian product during the past five years, G. M. Carrie was requested to prepare such a paper. The Canadian producers of magnesia refractories have succeeded in developing the product to a place where it has almost entirely displaced imported materials from the Canadian market. These developments were made possible by a close study of the methods of preparation of the material, and by an exceedingly careful control of the manufacturing process so as to obtain a thorough blending of the different constituents with the resultant uniformity of composition. This point is very important to the metallurgist, as un-uniform materials are a potent cause of difficulties in most manufacturing processes and the constant trend is towards their elimination. The temperature at which the Canadian material is burned ensures high specific gravity and thorough shrinkage. The grain size of the product is so controlled that the voids are only just sufficient to allow of proper bonding, thus making possible a dense, hard bottom affording high resistance to erosion and shock. Careful proportioning of the constituent elements absolutely prevents disintegration.

Jan 1, 1927

By Giulia M. B., Ferruccio Cribari, Alessandro Bertero, Eliano Romani, Roberto Sorge, Francesca Casini

"The use of Artificial Ground Freezing (AGF) to form earth support and seepage control barrier systems has had applications worldwide. These cover a variety of construction problems, including the formation of frozen earth walls to support deep excavations, structural underpinning for foundation improvement, and temporary control of ground water in construction processes. An application of AGF during construction of Line C of Rome underground is described in detail.The new line “C” of San Giovanni metro station was constructed adjacent to the existing line “A” of San Giovanni station; the new metro line “C” is deeper than line “A” and runs below the existing station. The underpass project envisages an Artificial Ground Freezing in order to create a structural and waterproof temporary cut-off suitable to the two new tunnels excavation, while keeping trains running in the safest possible condition. The excavation of tunnels under the water table, with a hydraulic head of over 10 m in not homogeneous soils having different mechanical properties and permeability and below existing sensitive structures, involves special ground freezing sequences and methods, as well as peculiar drilling systems and operations, such as TDDT (Trevi Directional Drilling Technology).Artifical Ground Freezing IntroductionNatural freezing occurs seasonally in many areas of the globe and can affect negatively the engineering performance of geotechnical structures; on the other hand, man-made freezing is a controllable process that can be used by civil engineers to stabilise temporarily the ground in order to support and/or exclude groundwater from an excavation until the final retaining and lining structures are constructed. Freezing and thawing of the pore fluid within soils involve complex thermal, hydraulic and mechanical processes that have significant mutual interactions. For example, phase changes of the pore fluid caused by temperature variations can modify the pore water pressure in the soil, which, in turn, can induce mechanical deformation. At the same time, any changes in the hydraulic and mechanical conditions affect the thermal processes by advection and changes of ice and water contents.An application of AGF which will be presented in the paper, refers to the construction works of Line C of Rome underground. In this case AGF was carried out to provide temporary support during excavation of the two Line C running tunnels directly underneath the existing S. Giovanni station of Line A, in the safest possible condition. In order to keep the trains of Line A operational during excavation, a temporary structure was installed and a real-time monitoring system was conceived in order to control the temperatures of the soil during freezing and the response of the structures of the existing station."

Jan 1, 2016

By Yi Luo

In a shearer longwall mining operation, the longwall bits are responsible for breaking into and chip-ping the broken coal blocks away from the coal face. However, underground observations have found that a large number of longwall bits are always working under various degrees of wear. Reduction of the bit wear could be realized by using better designed longwall bits and properly selected shearer operating parameters. A computer program has been developed to simulate the performance of the longwall bits. The shape of the bit head, the installation of the bits on the drum and the operation parameters are the information required by the program. Through the simulations, the main factors affecting the bit wearing process are identified. Suggestions are also made for improving the design of the longwall bits.

Jan 1, 1996

By Ryan C. Stephan, Zach Agioutantis, Christopher Mark

During the past 15 years, roof fall rates have fallen dramatically in US coal mines, particularly in regions where the roof is weakest. The remarkable reduction in the number of roof falls has been accomplished with more effective roof support systems. The purpose of this paper is to present a design methodology that builds on and quantifies the basic roof support concepts that have been successful in the USA. The methodology starts by defining three modes of roof support, based on the roof strength relative to the stress level: (1) suspension, where roof bolts mainly provide skin control for strong roof; (2) beam building, where moderate strength roof can be supported by roof bolts alone; and (3) supplemental support for weak roof. Next, a large database of roof fall histories at a number of mines is used to define the approximate boundaries of these three regimes based on the coal mine roof rating and the depth of cover. Finally, guidelines are presented for site-specific design of support systems within each regime. The new computer package, analysis of mine roof support (AMRS), implements the design methodology.

Sep 29, 2020

By Thomas L. Ochs

The Bureau of Mines is investigating the fundamental behavior of electric arcs in electric furnace operations. The electric arc is a poorly understood phenomenon. If the arc in a steelmaking furnace can be more carefully controlled, it should be possible to increase heat transfer to the melt, reducing both electrical and acoustical noise. As a first step toward a better understanding of the are, voltage and current signals from operating furnaces were analyzed. The results of the initial analysis show that instrumentation used in monitoring and controlling furnaces, such as meters and strip-chart recorders, gives incomplete or erroneous information to the operator and therefore leads to less than optimal control. Advanced instrumentation and analysis techniques, such as the waveform analysis used in these investigations, can improve the understanding of operation and the control of electric furnaces. This report describes the instrumentation and the numerical analysis methods used and compares these methods with standard metering and recording techniques.

Jan 1, 1986

By Paul-Dominique Oudenne

For many years, CMI NESA has gained considerable experience in the field of alternative thermal processing processes by which useful by products result in addition to the destruction of the raw wastes. The CMI NESA pyrolysis process has been extensively applied to a wide range of sewage, industrial sludge and residues. This paper describes in details the development works carried out at the pilot stage as well as the key parameters of the process. Some of the industrial realisations are briefly described, the most recent one being the erection of a sludge pyrolyser on predried sludge at 90% dryness of a capacity of 100 tons of dry matter per day for the Valenton plant of the SIAAP (city of Paris).

Jan 1, 2006

By J. J. Dowd

1. The Pittsburgh bed is the most important bed in Marshall County, and virtually the entire production of coal in the county comes from this bed. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, were estimated at 3,158 million short tons as of January I, 1954. Of this total, 3,071 million short tons is in beds 28 inches and more thick. Areas in each bed except the Pittsburgh were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By R. Khanna, I. Mansuri, S. Devasahayam

"Recycling polymer based end-of-life materials as carbon resources for a partial replacement of coke/coal can make important contributions towards enhancing the environmental sustainability of steelmaking processes. An in-depth high temperature (1550°C) investigation has been carried on waste CDs/DVDs focussed specifically on char generation, characterization and dissolution into molten iron. The simultaneous presence of carbon and oxygen in polymeric chains on polycarbonate substrates resulted in the generation of a significant pore structure and exposed surfaces. Carbon dissolution studies into molten iron were carried out on the raw polymer as well on chars; high levels of carbon pick-up were observed in both cases after 15 minutes of contact at high temperatures. INTRODUCTIONOver the past sixty years, plastics have played an important part of our daily lives and are being increasingly used in all aspects of the global economy. More than 260 million tons of plastics are produced annually worldwide. Their rapid growth and extensive utilization with a short life span (such as packaging) has created a massive waste problem. Although the waste plastic component in municipal solid waste (MSW) amounts to only about 10 %, plastics have a high volume-to-weight ratio and these are generally not biodegradable. In Australia, ~19.20 % of plastics were recycled in 2009-2010 (PACIA, 2010); with the total consumption being estimated at 1,501,258 tonnes, 288,194 tonnes of plastics were recycled. There are serious environmental concerns with the two key waste management options, i.e. land filling and incineration, and there exists an urgent need for developing alternative recycling approaches. In this paper, we focus our attention on recycling waste CDs/DVDs polycarbonate substrates as a carbon resource in steelmaking.CDs/DVDs used for music/data/image are made from aromatic polycarbonate resin (hereafter abbreviated PC). This resin is also widely used as an engineering plastic in applications such as automobiles, mobile phones, notebook type personal computers, cameras & video cameras, electric & electronic appliances, fire equipment, life & living goods, roofing sheets, etc. High consumption and growth (~10% annually) of PC utilization is attributed to its excellent properties such as outstanding impact resistance, transparency, heat resistance, and dimensional stability. The molecular formula and composition of PC resin is given below:"

Jan 1, 2012

By D. P. Lindroth

The thermal diffusivity above 298 K, up to 400 K and at pressures from ambient down to 10-10 torr was measured for the following six igneous rock types: tholeiitic basalt, obsidian, rhyolite, granodiorite, gabbro, and dunite. The thermal diffusivity data were obtained by the laser flash method. Extreme values range from a low of 5.3X10-3 cmF/sec for rhyolite at 383 K and 2X10-7 torr to a high of 13.4x10-3 crrf/sec for dunite at 298 K and 760 torr. Data are also included on a commercial fused silica, which was used as a standard.

Jan 1, 1974

By C. G. Storm

Permissible explosives are those that have passed the tests pre- scribed by the Bureau of Mines for explosives intended for use in coal mines, and are therefore recommended by the bureau as suitable for this class of work when used under the prescribed conditions. The tests for permissible explosives and the conditions prescribed for their use are described in Miners' Circular 6 of the Bureau of Mines. Up to June 1, 1915, 168 explosives had been classed as per- missible explosives; 133 of them were then on the bureau's "per- missible list" and 35 had been withdrawn by the manufacturers. In addition to the required physical tests, each explosive is sub- jected to a complete chemical examination in order that its exact composition may be known and also that the composition of future samples of the same explosive collected in the field may be compared with that of the sample which originally passed the bureau's tests, for by such comparison it may be possible to ascertain whether or not the explosive as supplied to the miner is still "permissible." This bulletin is published primarily for the purpose of informing manufacturers of such explosives as to the methods used by the Bureau of Mines in the analysis of samples received for tests to determine their permissibility. Such information may be of value in cases of possible controversy over the results obtained in the analysis of a field sample as compared with those obtained in ana- lyzing the sample originally tested by the bureau. Also, a descrip- tion of the methods used by the Bureau of Mines in the analysis of explosives should be of assistance to the many chemists engaged in similar analytical work.

Jan 1, 1916

By A. G. Moon

Kennecott Copper Corporation's Chino Mines Division concentrator is located in Hurley, New Mexico. Construction of the concentrator was started in 1910 and its capacity was progressively increased over the years to the present nominal 20, 425 t/d of ore (22, 500 stpd). The principal copper minerals present in the ore are chalcopyrite and chalcocite with much of the chalcotite intimately associated with pyrite. Lime is used to depress pyrite, and flotation at a high pH or alkalinity is required for optimum recovery of chalcocite with good rejection of the pyrite. Regrinding is also required to liberate chalcocite-pyrite middling grains. Accurate control of the lime addition is necessary to obtain both optimum metallurgy and minimum lime usage. At low pH levels, flotation cell control is difficult due to excess froth, but excessively high pH levels can go unnoticed because froth characteristics do not change from those experienced at the deisred pH. With manual control of the lime addition, the desired pH can be exceeded for periods of up to two hours. In 1972 a major renovation of the flotation and regrinding circuits was com¬pleted and at that time a new lime distribution and control system was placed in operation. Limestone is obtained from a nearby quarry west of Hurley. The limestone is crushed, sized and fed to a rotary kiln and the quicklime product is stored prior to slaking. The lime is slaked, as required, in a mixing tank-classifier type slaker and the lime slurry is pumped to a concentrator storage tank from which it is distributed through a conventional closed loop system. The current average lime usage rate is approximately 6 kg/t of ore (12 lb per st).

Jan 1, 1976

By Richard R. Walker, John J. Watkins, Allen C. Amos, Matulich. Angelo

THE KIDD CREEK MINE is located within the Abitibi greenstone belt, near its west end, in an area known as the Porcupine mining camp (Fig. 5). The Abitibi belt, long known for its many major gold and base metal deposits, is the largest Archean (early Precambrian) greenstone belt within the Canadian Shield. In the Porcupine area, the greenstone belt is composed principally of Keewatin (older Archean) basic to intermediate volcanics, with subordinate felsic volcanics developed• locally. Greywacke, mainly of volcanic derivation, occurs associated with and overlying these volcanics. Timiskaming (younger Archean) sediments, principally coarse clastics, unconformably overlie the Keewatin volcanics and sediments. The reader is referred to Goodwin and Ridler (1970) •r. for a more comprehensive description of the Abitibi belt.

Jan 1, 1974

South Africa remains the largest global producer of gold, accounting for 11.3 per cent of total world mine production, which amounted to 2520.2 t in 2005. The benefits and disadvantages associated with hedging practices in general, and among South African gold producers is examined. The wide variety and unique nature of risks faced by the mining industries provide a strong case for hedging. Only the principles of hedging, such as selling ounces of gold in the ground at a pre-agreed price for delivery at a future date as a cost-effective mechanism for price risk management, is discussed. Progressive and cumulative increases in the volume of forward sales in the major producing countries are considered by many to be the cause of the declining gold price over the past decade. In spite of negative publicity, forward selling continued as an industry-wide practice until recently (2002) when the global hedge book contracted by 352 t; contraction amounted to 158.6 t in first quarter of 2006. The objectives and benefits of hedging include continuity and stability of cash flows, stability in price achieved, reduction of frictional costs, and creating an effective management tool. The importance of a defined hedging strategy in reducing uncertainty about the hedging objectives is essential to a successful hedging policy. Historical patterns in hedging revenues at an industry level indicate five distinct periods during which the fortunes of hedgers have fluctuated. Finally, since 2001 the rising gold price and reduced price volatility through the consolidation in the global price means that the need to stabilize revenue flows is less urgent. This has meant that hedging is becoming progressively less important for the mining industry at large.

Jan 1, 2007

By M. Hopf

The use of water-cooled copper components as sidewall elements of submerged arc furnaces and other pyrometallurgical applications has become increasingly common. The high cooling efficiency of copper has made it possible to increase the service life of furnace refractories when compared to conventional refractory linings. However, even the self-healing effect of ?freezing? worn areas of the lining does not necessarily protect the copper coolers against wear or corrosion completely. In order to avoid furnace explosions, various methods have been used to monitor the wear of coolers. Unfortunately, these have not been able consistently to identify localized wear. Thos Begbie (South African) and SAVEWAY (German) jointly developed technology to embed a line sensor into the copper cooler during the casting process. This system allows an exhaustive monitoring of the copper cooler. A SAVELINE sensor is placed inside the copper-cooling panel between the water-cooling passage and the hot face of the panel. The sensor follows the meandering shape of the cooling water channels. In the first instance, the sensor provides analogue information as the thickness of the copper reduces. Secondly, this wear signal will be confirmed by a signal of interruption if the sensor is washed away. Because of the structure of the sensor, a self-diagnosis is possible and indications can be confirmed (double proofed).Subsequent to the manufacture of some test pieces, coolers for a large submerged arc furnace were manufactured. The sensorized coolers have been installed at the intermittent surface (slag line) where the largest amount of corrosion has been encountered. The system has been operating since December 2005 in what is considered one of the largest submerged arc furnaces in South Africa. Keywords: Pyrometallurgy, furnace, copper coolers, freeze lining, monitoring, Saveway

Jan 1, 2006

By B. C. Slocombe

A large derelict inner city site was regenerated for use as a distribution warehouse. Difficult topography and soils conditions required the adoption of a combination of specialist geotechnical processes. Particular attention was paid to the preparation of the site, programming and capabilities of each technique as additional soils information became available.

Jan 1, 1989

By Malte J. M. Gurgel, Axel Preusse

Recent three-dimensional surveying techniques have opened up new opportunities for the registration and monitoring of underground cavities. There are essentially two main methods available: Laser scanning, which is used both above surface and increasingly underground, and photogrammetry, which is also experiencing a renaissance with techniques like structure from motion through the algorithm-based orientation of high-resolution images. Both methods provide the capability to reconstruct reality by various 3-D products like points clouds and meshed models. However, they differ significantly in the steps of registration and calculation as well as in the resulting evaluation options.

By G Richmond, J R. Glen

Western Metals Mt Gordon Operation is a copper mine and processing plant situated 120 kilometres north of Mt Isa. The unique Mt Gordon copper process utilises a whole of ore acid/ferric pressure leach to produce copper cathode from the Esperanza massive sulfide copper orebody. Esperanza ore contains chalcocite, covellite and minor chalcopyrite hosted in a massive pyrite matrix. These ore stocks will be depleted in late 2003. Recently the process circuit has been upgraded to allow the treatment of lower grade Mammoth ores. These include the installation of a ball mill to complement the existing SAG mill, a single stage rougher flotation circuit and a tailings thickener. The leach bleed neutralisation plant was also upgraded at this time. Commissioning of these new circuits occurred in March 2003 and involved all the challenges of ensuring current production levels were successfully maintained while new process steps were incorporated into the whole circuit. This paper explains the background flow sheet of the patented Mt Gordon process and the reasoning behind the enhancements required for an already successful copper leaching circuit. Included are discussion of the influences of the new ores on individual process components such as comminution, leach chemistry and solid/liquid separation. Longer term ore processing options are also discussed.

Jan 1, 2003

By C. Allen, V. Hensel, J. S. Stachulak

"Vale has been actively evaluating new technologies to curtail diesel emissions. This paper discusses the selection, installation, operation, and evaluation of the MANN+HUMMEL SMF®-AR diesel particulate filter system to reduce diesel particulate matter emissions in underground mines. The system uses a sintered metal filter element, an iron fuel-borne catalyst with an onboard dosing system, an electric heater that uses onboard power, and a sensor-based control unit. More than 6,000 h of testing demonstrated that the system represents a breakthrough in the successful control of soot emission from light-duty vehicles with differing soot emission levels, exhaust temperatures, and duty cycles.RÉSUMÉ La compagnie Vale évalue activement de nouvelles technologies pour réduire les émissions de diesel. Le présent article discute du choix, de l’installation, du fonctionnement et de l’évaluation du système MANN+HUMMEL SMFMD-AR de filtrage des particules de diesel pour réduire les émissions de particules de diesel dans les mines souterraines. Le système utilise un élément filtrant en métal fritté, un catalyseur à base de fer dans le carburant avec un système de dosage intégré, un élément de chauffage électrique qui utilise l’alimentation incorporée et une unité de contrôle avec un capteur. Plus de 6 000 heures d’essais ont démontré que le système représente une avancée pour réussir à contrôler les émissions de suie des véhicules légers avec différents niveaux d’émission de suie, différentes températures d’échappement et différents cycles opératoires."

Jan 1, 2015