Search Documents

By G. Goodall, R. Jabbar, S. Muinonen, A. Cummings

"Glencore’s Sudbury Integrated Nickel Operations in Falconbridge, Ontario, has been in operation since 1930. Many new technologies and practices, now common in the industry, have been implemented at the site and contribute significantly to the industry’s understanding. Since the last update on the Smelter operation published at the NiCo 2005 conference, the Converter Aisle has undergone significant changes in the operation of vessels. The Aisle continues to consist of 4 Peirce-Smith converters, but the Slag-Make Converter, and the Slag Cleaning Vessel have been re-tooled or re-built as Hybrid Vessels (HV), each generating matte for the two Finishing Converters and clean slag for disposal. The complicated scheduling and the overall benefits to the Smelter are reviewed here as part of the on-going tradition of industry support.INTRODUCTION The Glencore Nickel Sudbury Smelter operates a Roast Reduction Smelting (RRS) flow sheet with a specialized Converter Aisle operation that maximizes metal recovery to Bessemer matte. The main process equipment consists of a pair of Fluid Bed Roasters, a submerged-arc Electric Furnace and four Peirce-Smith converting type vessels (Figure 1). In the RRS flow sheet, concentrate is roasted with air to remove sulphur as SO2. Calcine from the Roasters is mixed with petroleum coke upon addition to the six-in-line rectangular Electric Furnace. The coke back reduces the metallic oxides, producing a matte and a discard slag.Gases from the Roasters are sent to a single pass absorption Acid Plant where the SO2 is converted to acid. Under the previous operating targets, approximately 70–75% of the sulphur in the incoming concentrate was fixed as acid with the balance going to the Electric Furnace in calcine for Bessemer matte production. Off-gases from the Electric Furnace and Converters are combined in a balloon flue, treated for particulates in electrostatic precipitators and discharged to the Smelter stack without any SO2 fixation."

Jan 1, 2017

By Duane L. Abata

Toxic gases produced by the detonation of six explosives were measured in an underground hardrock metal mine during actual mining operations. The six explosives included two semigelatin dynamites, three slurry explosives and an ammonium nitrate, fuel-oil/ammonia dynamite combination. Explosives were detonated at the face of a drift and the toxic gases produced by the detonation were trapped to the end of the drift by a bulkhead located a short distance away from the face. Toxic gas concentrations were then measured with direct readout instruments and together with the containment volume, the toxic gas volumes per mass of explosive were calculated. Toxic gas measurements were found in the following ranges (ft3/lbm): NO, 0.010-0.035; NO2, 0.003-0.019; CO, 0.08-0.30; S02, 0.00-0.05; and CO2, 0.7-1.8. Results showed that toxic gas production (ft3/lbm) correlated with the densities (kg/m3) and energy densities (kJ/kg) of the explosives tested.

Jan 1, 1979

By A. G. Kim

Methane and other hydrocarbon gases, byproducts of coalification, are emitted from coal at widely varying rates and often present ventilation problems during mining. The air in some coal mines apparently contains no methane. To determine if coals from mines which bid no history of detectable gas emission contained adsorbed methane, samples of coal at the shaft bottom and at an active face were obtained and placed in sealed metal cylinders. The atmosphere around the coal was sampled and analysed by gas chromatography. Methane, ethane, ethylene, propane, propylene, and butane were found to have been desorbed from these coals. Hydrogen and helium were also detected. An estimate of the amount of residual gas per ton A coal indicated that coal samples from the active face generally contained more adsorbed gas than coal samples obtained from the shaft bottom, although in both instances the total amount of gas was relatively small.

Jan 1, 1973

By Michael S. Miller

During U.S. Bureau of mines mineral investigations, in 1981 and 1983, no mines, prospects, or mineral resources were identified in the Little Sand Spring Wilderness Study Area (WSA). Placer gold values in near-surface samples from alluvial fans within or near the WSA contained no more than 66 cents gold per cu yd, at $400 per troy ounce gold price. Sand and gravel and carbonate rocks occur in large quantities, but transportation costs to distant markets preclude their classification as resources. Nitrogen, lithium, clay, pumice, perlite, aragonite, and agate occurrences in the WSA are small or low-grade. The Silvia Mine, adjacent to the WSA contains gold-, silver-, copper-, and lead-bearing shear zones which strike toward the WSA. INTRODUCTION The Little Sand Spring WSA, encompassing 33,500 acres, is approximately 56 mi east of Big Pine, California, by paved and graded dirt roads (fl;. 1). Elevations range from 2,600 ft in Death Valley Wash to 5,600 ft along the California-Nevada boundary. The nearest permanent facilities are at Grapevine Ranger station and Scotty's Castle (Death Valley Ranch), about 9 and 11 mi, respectively, south in Death Valley National Monument.

Jan 1, 1983

By P Holtham, K C. Runge, E Tabosa

Traditionally, comminution and flotation have been surveyed, analysed and optimised separately. This often results in less than optimal outcomes because of the complex interactions between the two processes. Flotation recovery is a strong function of the valuable mineral particle size distribution with lower recovery of ultra-fines due to poor flotation kinetics, optimum recovery for the intermediate sized particles and lower recovery for the coarser particles due to poorer liberation. Thus, to optimise flotation recovery and grade it is usually best to grind to a fine size. This requirement needs to be balanced by the cost of grinding finer and the revenue that results from an increase in grinding throughput, which often results in a coarsening of the flotation feed.This paper demonstrates a technique which can be used to predict the effect of a change in feed grind size on flotation performance. It can be used to determine the optimum grind size for a particular operation which optimises total circuit profitability. Analysis is relatively easy to perform, as a minimum, requiring only size by assay data of the feed and product streams of the process. Case studies will be presented that demonstrate the usefulness of this technique in feed grind applications. Potential use of the technique for regrind evaluation is discussed. The limitations associated with this technique in certain circuit scenarios will also be outlined.CITATION:Runge, K C, Tabosa, E and Holtham, P, 2014. Integrated optimisation of grinding and flotation circuits, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 77–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By F. J. Chernosky

Most previous studies of coal flotation utilized chemically pure reagents. Since such reagents are not available in quantity, a study of various wmmercially available reagents as frothers was undertaken. Flotation procedures similar to those used in a large number of commercial coal flotation plants were employed. The reagents used were compared on yield-selectivity-wst basis. The selectivity was found to be relatively constant with yields above 70% but the reagent cost varied greatly. The types of reagents available were compared. In the past, a number of papers have been written on the use of various reagents as coal flotation frothers. For the most part, these have been an attempt to correlate the intrinsic chemical and physical proper- ties of the reagents or reagent groups to the floata-bility of various fine coals. Because of the type or nature of evaluations made, chemically pure reagents were normally used. Generally, these reagents are unavailable in commercial quantities. Therefore, the results obtained with these reagents were usually limited in usefulness to the plant operator or metallurgist. This paper presents the results of a study in which commercially available forms of various reagents were used as flotation frothers. Flotation procedures which would conform in general to those employed in a large number of commercial coal flotation plants were utilized. The objective of the test was to compare these reagents on yield-selectivity-cost basis, that is, 1) the yields obtained, 2) the ash levels obtained and 3) the reagent cost relating to these results. REAGENTS The reagents employed have been grouped into the following chemical classes: 1) aliphatic alcohols, 2) terpines, 3) glycols (synthetic water-soluble

Jan 1, 1963

By Jeffrey W. Braithwaite

The laboratory characterization of the oxidation of chalcopyrite under conditions of deep solution mining is presented in this paper. A salient feature of this system is the pH buffering effect resulting from simultaneous acid producing and acid consuming oxidation reactions. The solution chemistry and related sulfur partitioning of the oxidation reactions are detailed. The contribution of temperature, acid concentration, oxygen pressure, particle size, and solution additions to the kinetics of copper extraction are presented. A mixed kinetic model was used to describe the kinetics of oxidation.

Jan 1, 1976

By J. -W. Kim, Y. -B. Kang, H. -G. Lee

The effect of SiO2addition on the decomposition of Li2CO3was investigated at temperatures up to 1000ºC. It was found that addition of SiO2greatly enhanced the decomposition of Li2CO3. The main decomposition reaction started at around 600ºC, and completed just above the melting point of Li2CO3. The major decomposition product was Li2O?SiO2irrespective of the Li2CO3to SiO2mixing ratio while both reactants were available. It was ascertained that a liquid layer betweenLi2CO3and SiO2particles formed and facilitated the decomposition reaction. The governing reaction of the decomposition was the one between the dissolved Li2CO3and SiO2in the liquid layer to form Li2O?SiO2. The decomposition rate was independent of the Li2CO3/SiO2mixingratio until either one had been completely exhausted. When excess Li2CO3existed, it further reacted with the initial product of Li2O?SiO2to form 2Li2O?SiO2. When SiO2was found in excess, on the other hand, no further reaction took place. This is attributed to the fact that uponLi2CO3exhaustion there is no liquid phase available to facilitate further reaction. The apparent activation energy of the decomposition of Li2CO3in existence with SiO2is 198 kJ mol-1.

Jan 1, 2004

By S. Nikolic, G. M. Stieper, D. P. Mallah, B. J. Hogg, P. B. Voigt

Copper feed materials processing is becoming more challenging, due to an incremental increase in the mineralogical and compositional complexity of these feeds. These complex and polymetallic feeds are now becoming more common and many sites have been forced to re-evaluate their operating strategies to process these materials at cost competitive rates, whilst meeting ever more stringent environmental regulations. Most operations must first evaluate the merits of pyrometallurgical and hydrometallurgical treatment routes. Although there are multiple copper smelting technologies available, only top-submerged lance (TSL) technology, supplied by Glencore Technology as ISASMELT™, has been applied in the real world to consistently and successfully smelt complex materials in integrated metallurgical facilities such as Glencore’s Kazzinc Ltd. operation in Kazakhstan, Umicore Precious Metals Refining in Belgium and Aurubis AG in Germany. Glencore Technology also offers hydrometallurgical processing, through the Albion Process™ technology, opening up viable flowsheet options previously not possible for these complex feeds. This paper describes a number of real world process flowsheets at global operations and Glencore’s own operations at Mount Isa and Kazzinc Ltd., which process complex feeds. These flowsheets integrate the ISASMELT™, Albion Process™, ISACONVERT™, ISAKIDD™ Tank house, and bottom blown oxygen cupel (BBOC™) technologies to provide an effective process solution for the treatment of complex polymetallic feeds to produce metallic copper and associated by-products. INTRODUCTION Traditional smelters and those built in recent times within the bulk smelting hubs of the world have been designed to treat standard/clean concentrates. In recent years the processing of complex polymetallic sulfide concentrates and the recycling of secondary copper and derivatives of waste electrical and electronic equipment, such as e-scrap, have become a focus for numerous companies (Alvear & Nikolic, 2013). Processing of these complex feeds, characterized by relatively high levels of minor elements (over 5% of elements such as arsenic, antimony, bismuth, lead and zinc) is more challenging. Facilities not designed for these types of materials may require significant modifications or a change in smelting technology to treat them. Often operations find themselves re-evaluating the merits of pyrometallurgical and hydrometallurgical treatment routes for their sites through a number of factors:

Jan 1, 2019

By Alfred V. C. Meyer

A Blastcorder4 was calibrated on the Bureau of Mines shaking table in the frequency range of 12 to 40 c.p.s. and in the amplitude range' of 0.25 to 1.0 g. The results of this calibration study show that in the frequency range of 12 to 30 c.p.s. the average accuracy of the Blastcorder is approximately ± 0.1 g.

Jan 1, 1962

By Yuzhe Zhang, Matthew Andriese, Jiann-Yang Hwang, Guanghui Li, Zhiwei Peng, Tao Jiang

The microwave power absorption characteristics of iron oxides, including Fe2O3, Fe3O4 and Fe0.925O, have been studied by determining dielectric loss and magnetic loss distributions in 0.05-m-thick oxide slabs irradiated with 1.2-kW, 2.45-GHz microwaves. The results reveal that the dielectric loss is the main factor contributing to microwave absorption in Fe2O3 and Fe0.925O, while the magnetic loss dominates the power absorption in Fe3O4 below its Curie point. Uneven power distributions are observed in the slabs and this phenomenon becomes even worse at high temperatures at which the permittivity increases significantly. Quantification of power absorption in the oxides is of great importance for efficient and uniform microwave heating

Jan 1, 2015

By Rodrigo Jerez

Advances in inexpensive computer automation led to the development and use of a computerized ore control system at the Cyprus Copperstone Gold Mine near Parker, AZ. These new ore control practices improved accuracy, performance and productivity of the ore control effort. An automated system for data collection, including bar coding of blasthole samples, laboratory analysis, data management, grade estimation, cut delineation and ore zone stake out, plays a major role in ore control practices. This is of particular interest because of the large amount of blasthole information being processed, analyzed and reported daily. Copperstone Gold management has been progressive toward new, efficient methods regarding ore reserve estimation, long-term mine planning, short-term mine planning, ore control and surveying. Technological advances, including powerful personal computers, applicable mine planning software and surveying instrumentation, have become readily available and affordable. The computerized ore control procedures used at Copperstone include sample data collection, laboratory automation and computerized data management. These have reduced the time to complete ore control on a blast pattern by 50% to 75%. The final product - ore control - is generated in a more timely and accurate manner.

Jan 1, 1991

By G Harbort, K Quan

Traditional engineering practice for concentrator design uses a mixture of risk minimisation options and capital minimisation approaches. Often this is based on the preferences and experiences of the engineers involved.A geometallurgical approach involves identifying primary lithology, alteration, and mineral dispersion patterns within a deposit to allow representative samples for test programs. This provides a method to infer from laboratory test results meaningful production data for larger amounts of the ore body. Geometallurgical models can be integrated into the resource block model and subsequent mine plan and can assist in predicting when difficulties in the processing route might be expected, allow adjustment of the design to compensate for these or provide an early warning system so that production forecasts can be more adequately developed. Simulation modelling is the process of creating a computer model of a real system based on mathematical logic. In simulated time, the model explores the randomness and chronological sequencing of events observed on real systems. The objective is to mimic the real system with sufficient accuracy to make predictions of real behaviour under experimental conditions. Amec Foster Wheeler often use the ‘discrete-event’ simulation modelling technique. This method is well suited for inclusion of the statistical variation of effects in unit operation, mechanical availability, throughput and operating strategy (based on historical operating data for equipment downtime), operating schedules and equipment capacity. The net result of the simulation model is an analysis that can quantify risks in terms of system performance and capital and operating costs.CITATION:Harbort, G and Quan, K, 2017. Concentrator design – standard engineering practice versus geometallurgy and simulation, in Proceedings MetPlant 2017, pp 195–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By D. C. Oldroyd

Western Coalfield?s Tandsi Mine, has difficult support conditions and a history of roof falls, resulting in mining roadway widths and depths being restricted for safety reasons. Rock Mechanics Technology Ltd was contracted to improve the support system to allow the introduction of mechanised room and pillar mining. The introduction of a ?world best practice? bolting system resulted in major improvement in roof stability, allowing mining restrictions to be lifted and Tandsi to become one of the first two Indian mines to introduce a mechanised continuous miner system. The first year?s production was some six times previous levels. Because of the improvement in the support system, RMT was also able to design a partial de-pillaring system suitable for the Tandsi continuous miner districts together with the introduction of monitoring procedures and guidelines to maintain safe roof support conditions. In situ monitoring of pillar and roof behaviour was undertaken as the first pillars were extracted to confirm the design. De-pillaring operations have also proved highly productive, and to date there has been no associated support related major injury or dangerous occurrence. The success of this project demonstrates the potential for mechanised room and pillar mining in India.

Jan 1, 2006

By D. J. Young

Alloys used at high temperature must resist both creep and corrosion. Design for corrosion resistance is based on the formation of a slow-growing, protective oxide scale by selective oxidation of an appropriate alloy component, usually chromium or aluminium. A successful scale will exclude other corrodents, notably carbon, which can otherwise cause extremely rapid corrosion at high temperatures. Selective oxidation of an alloy component necessarily lowers the concentration of that metal in the alloy subsurface region. Under thermal cycling conditions, mechanical damage to the scale leads to renewed oxide growth and accelerated alloy depletion. Eventually, a point is reached where diffusion of a corrodent into the alloy becomes competitive with the outward diffusion of alloy metal to repair the protective scale. Two examples of alloy failure by carbon attack are considered. In the steam cracking (pyrolysis) process, centrifugally cast tubes of heat-resisting alloy are exposed to a gas stream of hydrocarbon and steam, at a carbon activity of unity. Formation and repair of the surface chromia scale causes alloy depletion, Kirkendall void formation, and subsequent internal precipitation of chromium-rich carbides. Their formation makes chromia scale formation much more difficult, and generates internal stress. Eventually, the tubes fail by creep rupture. In other processes (e.g. steam reforming, heat treatment), synthesis gases are supersaturated with carbon at intermediate temperatures. Once the alloy's protective scale is breached, carbon attacks the depleted substrate. In the case of ferritic alloys, it forms a surface scale of Fe3C. As this scale thickens, the supersaturated carbon precipitates as graphite within its outer regions. The resulting volume expansion causes disintegration of the cementite in a process known as metal dusting. In the case of austenitic alloys, no metal carbide is formed. Instead, carbon dissolves in the depleted metal to diffuse inward and precipitate as graphite within the metal matrix. Again, volume expansion causes disintegration of the alloy, and metal dusting results. Dusting occurs at an extraordinarily rapid rate, and leads to failure by section loss or even penetration.

Jan 1, 2013

By W. A. Lang

Introduction In this review, which is the fifth of the series on the Progress in Coal Technology, an attempt has been made to outline some of the more important developments that have taken place in coal carbonization during the last decade. Research into both high-and low-temperature carbonization has been active for three principal reasons: (1) the growing shortages in most countries of high-quality coking coals; (2) the demand for smokeless fuels for domestic purposes; (3) the need for metallurgical coke for the increased output of steel in the post-war years. The growing importance of coal tars as a source of chemicals for the preparation of synthetic products and of coal gases for the recovery of sulphur is evident. Many of the researches initiated because of wartime necessity have been continued .and even expanded in the post-war years. High-temperature carbonization with a suitable coal yields a strong coke which is used primarily for metallurgical purposes, a tar with good marketable value, and a large yield of gas of medium calorific value. Low-temperature carbonization gives a more free-burning solid product suitable for a domestic fuel, a high yield of a tar which is generally regarded as superior to high-temperature tar for chemical purposes, and a smaller yield of a higher-heat-value gas.

Jan 1, 1951

By J. H. Stears

Increasing use of Birmingham and other roof trusses prompted a Bureau of Mines study of support forces produced on a mine roof by these members. Equations, obtained from laboratory and field tests, are given for calculating the contact forces between the roof strata and a typical truss. Actual contact forces for a specific truss are difficult to estimate because of variable friction loss at the contact points. A finite-element analysis, using typical contact forces, indicated that trusses have a negligible effect on the stress field in massive, competent roof strata. The effectiveness of trusses in supporting broken rock strata was not analyzed. However, experience has shown that trusses are effective in supporting incompetent roof.

Jan 1, 1988

By J. B. McKay

It is the purpose of this paper to present an initial report on the construction and operation of the Fluo-Solid roaster at the property of Campbell Red Lake Mines, Ltd., Balmertown, Ontario. The roaster prepares for subsequent cyanidation the bulk flotation concentrate obtained from four hundred tons per day of gold ore. The mill flow-sheet 'includes jigging and amalgamation; flotation; cyanidation of flotation tailing; and roasting followed by cyanidaition of flotation concentrate plus amalgamation tailing. Overall mill recovery for the year 1950 was 90.2 per cent. Recovery possible by straight cyanidation of this ore would not exceed 80 per cent. The ore contains considerable arsenopyrite and pyrrhotite as well as pyrite, with lesser quantities of nickel, zinc, and copper minerals. The mineralization is for the most part extremely fine. The roaster first went into operation on August 7th, 1949, and at the end of 1950 it had roasted 10,916 tons of concentrate. The average recovery of gold from calcine during that period was 94.86 per cent in the primary stage of calcine cyanidation. The average assay of calcine residue from primary cyanidation for the entire period was 0.37 oz. per ton. Both laboratory tests and plant metallurgical balance calculations indicate a further recovery of approximately 10 per cent of this 0.37 oz. when the calcine residue is again cyanided, in the flotation tailing cyanidation circuit.

Jan 1, 1951

By C. R. Julian

THE large pyrites ore-bodies, the underground mining of which is to be described, are situated at Rio Tinto in the Province of Huelva in Southern Spain. The situation of the different ore-bodies with relation to one another is shown in Figure 1. It will be seen on the plan that the strike of the ore-bodies is approximately east and west. The geology of the district has been very fully described by Dr. D. Williams (1), so that for the purposes of this paper it will be sufficient to give briefly the salient features o each of the two larger ore-bodies which are being mined by underground methods at the present time. (a) San Dionisio.-This ore-body is the largest single deposit in Rio Tinto, having on its upper levels a length of 3,500 ft. On the upper levels the average width is approximately 200ft. but in places on the lower levels there is a width of 900ft. of un broken pyrites. Diamond-drill holes, without running out of ore, show the ore-body to persist to a depth of at least 1,600 ft. The ore-body in the upper part lies between slate and porphyry walls, but in depth is enclosed in porphyry walls. (b) South Lode.-Faulting is considered to be responsible for the break in the solid ore between South Lode and San Dionisio. On the upper levels, the South Lode ore-body has an unbroken length of 4,000 ft. The massive pyrites has a maximum width of 300ft. and an average of about 100 ft. Ore has been proved to a depth of 1,000 ft., at which depth the ore-body is much reduced both in length and breadth. This ore-body, to the depth at which it has been proved, lies entirely between slate and porphyry walls. The South Lode and the San Dionisio ore-bodies are mined both by open-cast and by underground methods. There is evidence that these mines have been exploited intermittently during the last 3,000 years; but, as is to be expected, no records are available of the tonnage mined prior to the time of purchase by the present company.

Jan 1, 1940

By G. F. Sowers

Excavation bracing is a special structural system. It is built from the top down. The design is controlled by the economical construction of another structure as well as by the movement of the ground beyond the limits of its construction. It serves a number of purposes, all subordinate to the construction of the principal structure. Despite its importance, bracing design and construction is frequently overlooked in project planning, causing delays and expensive changes. Thoughtful planning, good design and resourceful, innovative construction can improve construction safety and save time and money.

Jan 1, 2010