Search Documents

By W. H. Strickland, R. H. King

Ultrasonic ranging sensors are inexpensive, have no moving parts, have no lenses to clean, are normally small and unobtrusive, and can measure distances through moderate amounts of dust, smoke, and humidity, so they are well suited to underground mines. In the work reported here, conducted by the U.S. Bureau of Mines, researchers tested ultrasonic ranging sensors for their abiity to define rib line features for computer-aided navigation of underground mine mobile equipment. The investigation began with laboratory tests of field of view, angle of incidence, intersensor variation, and ranging accuracy of the individual rangers in a ring array produced by Denning Robotics of Wilmington, MA. The results showed that the sensors have good accuracy and low variability. Additional experiments at AMAX's Henderson Mine showed the sensors could accurately and reliably measure the distance to mine features, including convex and concave corners and rib intersections. The results showed that when used properly, the ranger data are accurate enough for reliable mine vehicle navigation When used incorrectly, ultrasonic rangers do not provide the anticipated data. Therefore, this report explains the principles of ultrasonic range measurement, describes the ranger's strengths and weaknesses, and explains proper ranger use and data analysis.

Jan 1, 1993

By C. E. Jordan

The fundamental properties of dielectric separation were studied to provide insight into the design and operating characteristics of a dielectric separator. Force equations on mineral particles were derived and evaluated experimentally. Responses to variations in the electrical voltage and frequency, feed rate, particle size, dielectric fluid, and dielectric constant were tested theoretically and experimentally, using a 5-cm-diam dielectric separator. High-dielectric mineral recovery was proportional to the calculated effective dielectric force volume (EDFV) that surrounded each drum-electrode wire. Electrode spacing was the most sensitive design parameter; spacing of less than 0.4 cm was required for a good separation. Dielectric separation was effective for separating minerals with dielectric constants that differed by approximately 2 or more.

Jan 1, 1985

By E. Poiate, P. R. Cabral, A. V. N. Santos, P. V. M. Costa, C. S. Amaral, A. M. Costa

This paper discusses the design of underground salt caverns, opened by solution mining, for the production of brine and storage of natural gas under high pressures. The caverns are located in the salt basin in Maceio City, Alagoas State, at the northeast region of Brazil. Special attention is given to the geomechanical structural design of the caverns using computer codes specially developed for the simulation of excavations in salt rock formations, considering validated constitutive creep laws under different initial stress states and temperatures. The behavior of sedimentary rocks intercalations presented in the salt layer is simulated using elastic-plastic models. The excavation of the caverns by solution mining is also simulated starting from a geostatic initial equilibrium state of stresses, with a unique formulation only implemented in these computer codes, without the need of the application of boundary stresses to the model in order to develop the initial state of stresses. These computer codes have being used in the design of several clusters of caverns for brine production used as raw material of Poly Vinyl Chloride (PVC) of the Chemical Industryin Brazil. These computer codes and methodology were also applied to the design of the underground conventional potash mine in the state of Sergipe, overlying tachyhydrite and carnallite with very high creep strain rate. They have also been used in the design of the pre-salt oil wells through thick layers of stratified salt rock in Santos Basin, for the exploration and production of the pre-salt reservoirs in Brazil. The constitutive creep equations implemented in the codes are based on a double mechanism creep law. The creep constants adopted in the simulation are taken from a previous investigation carried out on an experimental panel of the potash mine, considering the stratified geology with different salt rocks of the basin where the mine is located. These constants were also obtained by lab tests under different confined and differential stresses and temperatures.

Jan 1, 2015

By D. C. Reid

This paper describes the latest results in research and development currently being undertaken by the CSIRO Mining Technology Group to advance the automation capability of continuous mining equipment in underground coal mining operations. This research delivers enabling technologies that are essential in achieving increased roadway development rates as well as providing a safer working environment for underground mine personnel. Details are presented on technical developments and results of large-scale above-ground experiments conducted under field-realistic conditions. These experiments demonstrate the performance of the ?self-steering? capability which will enable a continuous miner (CM) to automatically maintain a given mining heading and mining horizon under production conditions. A primary technical requirement of this automated functionality is the means to accurately determine both the location and orientation of the CM in real-time. Test results of a high performance navigation system utilising vehicle motion aiding technologies are presented. This system combines high performance inertial sensors, and custom-developed radar to achieve a navigation-grade guidance system. Comprehensive performance evaluation has been conducted using a scale skid-steer mobility platform operating autonomously through a typical roadway development mining pattern with a total path length of 2700 m and mission duration of 112 min. Results from this evaluation demonstrate that the sustained accuracy of the navigation system exceeds the original project expectations and is well suited to the requirements for this underground mining application. There are presently no known alternative methods for providing a practical and accurate three-dimensional guidance solution in this application. This achievement represents a significant milestone in delivering a step change improvement in underground coal mining roadway development.

Aug 1, 2013

By J. Davitt McAteer

Dear Mine Operator, Training for new employees, refresher training for new employees, refresher training, and new task training can mean the difference between life and death for workers. Part 46 spells out how you can develop a training program to protect workers for on-the-job hazards. Together, labor, industry, and the U.S. Department of Labor reached a milestone with the development and publication of Part 46. We want to continue working together toward the next milestone, October 2000, when the regulations take effect. We want to make sure you have all the information you need about these new training requirements. Throughout the next 12 months, MSHA personnel will be holding regional meetings across the country, delivering information and sample training plans to your operation, and offering you help to develop your plan. If you are among the many operators who are already providing training to your workers, keep up the good work. The rule will tell you exactly what is expected. If you currently have no training program, we can help you develop one. A brochure is being distributed, which highlights the main provisions of the rule. It is designed to introduce the rule to you. More detailed materials will be delivered to you. If you want information right away, simply call us, or e-mail us. We also welcome your comments, suggestions, and success stories. Part 46 will be successful and beneficial to miners through our combined efforts. Together, we can make our mines safe and healthier for everyone. Sincerely, J. Davitt McAteer, Assistant Secretary of Labor Mine Safety and Health Administration

Jan 1, 1999

By Arash Nikvar-Hassani, Lianyang Zhang

To address the drawbacks of the conventional portland cement/fly ash (PC/FA)–based cementitious material currently used in practice to construct pumpable roof supports (PRSs), a novel cementitious material has been developed based on geopolymerization technology. The novel cementitious material is comprised of two pumpable grout streams: Stream 1 is a slurry composed of pozzolanic material and high-calcium additive and stream 2 is an alkaline solution comprised of a gelling agent. Biopolymer has been added to the second stream to provide ductility to the geopolymer cementitious material. In the laboratory scale, systematic experiments have been carried out to investigate the viscosity, setting time, and uniaxial compressive strength (UCS) of the new cementitious material and develop the right recipe for field applications. By collaborating with industry and the National Institute for Occupational Safety and Health (NIOSH), full-scale PRSs have been constructed and tested. The results show that (1) the novel cementitious material based PRSs has much higher peak UCS and similar or higher residual strength than the conventional PC/FA-based PRSs; and (2) unlike the PC/FAbased cementitious material, the novel cementitious material shows good long-term durability with nocracking/disintegration when exposed to air.

Jul 1, 2023

By J. Peterson, D. D. Tannant, J. Todd

"A review of blast designs and improved blasting practices at the EkatiTM diamond mine is presented along with the results of three blast-monitoring experiments. Blast monitoring was undertaken to investigate blast damage mechanisms in the mine’s well jointed rock mass. Rock mass damage caused by production, pre-shear and wall control blasts was measured. EkatiTM uses 270 mm holes for production blasting, and 165 mm holes loaded with a decoupled charge for pre-shearing. The production blasts are loaded with bulk emulsion/ANFO blends. The mine plan involves using 30 m double benches. A 30 m high pre-shear is drilled and blasted prior to the production blasting that is done with sequential 15 m benches. This paper summarizes the monitoring equipment and data gathered to date. IntroductionThe EkatiTM diamond mine is located about 300 km northeast of Yellowknife, Northwest Territories, Canada. The mine is a joint venture of BHP Diamonds Inc. (80%) and geologists Charles Fipke and Stewart Blusson (10% each). The EkatiTM mine is Canada’s first diamond mine and BHP is the operator. The mine is accessed by air and by a winter ice road.The first kimberlite pipe mined at EkatiTM is known as the Panda pipe. The Panda open pit mine will have a total depth of 315 m (Fig. 1), a width of about 600 m, and a 50° overall slope. Initial ore production is 9000 tonnes per day.This paper summarizes the pre-strip blasting and the evolution of the production and wall control blast designs from 1997 to 2000. The initial blast designs and the rationale behind subsequent changes that took place are presented along with the techniques currently in use.The paper also briefly presents an experiment done to measure the rock mass response to blasting. Three blasts were instrumented with geophones, gas pressure sensors and time domain reflectometry cables. A brief summary of the instrumentation and data gathered is included."

Jan 1, 2001

By M I. Pownceby, M A. Rhamdhani, D M. Fellicia, S Palanisamy, R Z. Mukhlis

The trend of global copper production has prospectively increased over time. Based on typical mined ore grades, 1 t of copper ore generates approximately 6–10 kg of copper, which requires much energy, usually in the form of metallurgical coke. Copper production using carbon as a fuel and reductant contributes up to 0.3 per cent to global greenhouse gas (GHG) emissions. As a result, research into decarbonisation processes applicable to reducing low-grade copper sulfide ores, copper oxides, electronic wastes and other alternative complex Cu-rich materials has increased. Alternative fuels for reducing carbon-rich emissions in pyrometallurgical copper processing include methane, ammonia, biomass, solar and wind power, but in recent times increased focus has been on hydrogen as a potential fuel and reducing agent for materials such as oxidised copper scrap, Cu2O/CuO and Cu-rich slags/e-wastes. From a thermodynamic perspective, hydrogen exhibits a significantly more negative standard Gibbs free energy (ΔG°) than copper oxide making it a suitable reductant and the exothermic thermal effect from reaction between hydrogen and Cu2O/CuO may be used to control process parameters. These characteristics renders hydrogen an ideal gas for reducing copper oxides and copper-containing slags/e-wastes. This review article assesses previous research on utilising hydrogen for producing and refining copper from primary and secondary feed materials.

Jun 19, 2024

By Tracey Brommer, Britt Elin Gihleengen, Elsa Olivetti, Randolph Kirchain

"Increased demand resulting from the economic and environmental advantages of recycling secondary materials has constrained secondary material supply. As a result of constrained supply, the conventional strategy to maximize recycled content in an individual aluminum alloy must be expanded to maximizing total recycled content in a given production period. This work compares the performance over a two week period of an actual remelter for two strategies; a sequential charge-by-charge optimization framework and an integrated approach that explicitly incorporates the production schedule. Optimizing across the entire two week production is found to increase recycled content and minimize primary and alloying material additions. It is expected that as the scrap material market continues to be constrained by high demand, longer term batch planning strategies that can optimize material allocation will deliver improved performance.IntroductionIntensifying economic and environmental pressure to incorporate secondary aluminum into products is pushing remelters to explore additional strategies and tools to increase recycled content. Aluminum remelters are exploring alternative sources of secondary materials because of constrained secondary material supply and relatively high primary and secondary material cost [1]. Computational models, such as blending models are a tool that could help industrial remelters mitigate supply and cost challenges and thereby increase recycled content. In particular, computational tools can help manage the incorporation of new raw materials of variable quality. Blending models find many industrial applications and have been explored for over sixty years originating with the classic nut-mix problem dating back to 1950’s [2]. Blending models optimize the raw material input to make a desired product subject to a series of constraints such as product specifications and material availability. Deterministic and linear blending model formulations are presently implemented in some industrial aluminum remelters [3]. The primary reluctance of aluminum remelters against computational model implementation is the incapability of their blending models to reflect the intricacy of industrial remelting conditions [4]. For example, to reduce calculation time, industrial aluminum blending models usually optimize a batch plan for a single alloy and are not formulated to optimize several products simultaneously. Since such a model does not include knowledge of subsequent charges in the optimized batch plan, the resulting batch plans tend to deplete the “cleanest” secondary materials leaving the more uncertain and compositionally challenging materials for later charges. As a result, a remelter may override the calculated batch plan or leave certain scrap materials out of the material input to conserve these materials for alternative products scheduled for later production. This work explores an alternative aluminum charge planning tool that can optimize across an extended production schedule and compares it to a heuristic sequential optimization strategy reflecting an industrial remelter."

Jan 1, 2012

By Michael J. Klishis

It was the goal of this project to develop training materials specific to two areas of the mining industry: (1) safe use and care of the self-contained self-rescuers, and (2) awareness and avoidance of electrical hazards. This report describes the development of the following training material: Instructor's modules for the OCENCO EBA 6.5, CSE AU-9A1, and PASS 700E self-contained self-rescuers; and a textbook, slide tapes, and accident case study scenarios for mine electricity, and a computer based instructional package on mine electricity and electrical hazards. The report concludes that additional efforts are needed in mine training and four recommendations are made: (a) tailor existing materials to fit specific mine sites, (b) develop and evaluate computer based instructional material, (c) develop parallel training materials for metal and non-metal mines and, (d) develop additional training materials for preparation plants and surface areas of underground mines.

Jan 1, 1985

By E. Nolasco, J. Ouellet, T. Tikka

"Shaft bottom structural systems are used in underground mining to support transfer of personnel, equipment and ore to and from underground to the surface. This paper first summarizes the evolution of design philosophy from a concrete tower supported on a concrete plug to the current structural steel design arrangement with unlined shaft walls, clear shaft bottom area with only a concrete housekeeping pad. Then the paper reviews the design parameters, analysis and design, and construction methodology for this rather unique shaft bottom structural system consisting of three sets of hitch beams, with each having specific functional requirements. INTRODUCTION Shaft bottom structural systems are used throughout the world in underground mining operations to provide a means to support the transfer of personnel, equipment, materials, ore and waste entering and exiting a vertical shaft ready for transport to and from the surface via the hoisting system. The shaft bottom structural system, for the Service Shaft (SS) at the Jansen Mine, is designed to accommodate two skips, a personnel/equipment cage, counterweight, services, loading pocket, rope changing, arrestor system, crash (or catch) beams, access platforms, stairs and rope divider system. Stantec and BHP have engineered a unique structural steel shaft bottom system for hoisting system at a Potash Mine. The shaft bottom structural system connects to a fixed guide and cantilever bunton system, used in the vertical shaft (shaft barrel), above the shaft bottom. The geometry for the shaft bottom structural system, shown in Figure 1 a), features three sets of hitch beams, beams which span across the shaft excavation or barrel. At the top of the structural system are two upper hitch beams. These hitch beams support a 64 metre suspended rectangular braced tower (upper tower), complete with steel guides for the conveyances. The upper tower passes through the main station (potash or mining) level and then connects to the top of the arrestor (lower) tower structure via a sliding vertical connection. The potash level is supported by two hitch beams spanning the shaft and loading pocket excavations. The arrestor tower, a braced compression tower structure, is carried by a third set of hitch beams. Below the third set of hitch beams is a short suspended tower complete with access platforms, stairs and the rope divider system."

Jan 1, 2019

By A. Daugiala, D. Coleman

In 2014 the New York State Department of Transportation (NYSDOT) awarded a Design-Build contract to the joint venture team consisting of Skanska which is the managing partner; Kiewit Corporation and Ecco III (SKE) and HNTB as the lead design firm. The design build team employed methods to provide schedule savings and commercial benefits to the owner NYSDOT. This paper presents the design approach and construction methods used to accelerate drilled shaft installation supporting the main span foundation for the cable stayed bridge. The drilled foundation contractor Underpinning and Foundation Skanska, a division of Skanska was responsible for assisting with design, budgeting and construction of the drilled shaft foundation construction. As part of the Request for Proposal (RFP) bid process, Alternate Technical Concepts (ATC) was encouraged by the NYSDOT. The JV team proposed an ATC which involved a scaled production shaft testing method to simulate the ultimate load level, commonly referred to as the “Chicago Method” was used in the rock socket employing the Osterberg Cell (O-Cell) testing procedures. To the authors knowledge this was the first NYSDOT project where this approach was utilized on a Demonstration/Production installation to validate construction procedures and load bearing capacities. Construction procedures, challenges and solutions are discussed in detail. Upon completion of successful drilled shaft construction, concrete integrity is verified using two methods – Cross Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP). A comparison from the contractor’s perspective is provided. Finally the drilled shaft rock socket is tested to ultimate end bearing values while rock socket side shear stresses are not exceeding the service level loading. Lateral load test was also a RFP requirement; the test arrangement and performance are discussed in detail as well. The Kosciuszko Bridge location poised unique geotechnical challenges on many levels shifting towards an extreme boundary of parameters encountered in New York City Area for drilled shaft construction. The JV team and specialty drilled shaft contractor actively participating in the shaft design and construction practice coordination and working with NYSDOT yielded a successful foundation solution which provided cost and schedule savings to the project.

Jan 1, 2016

By Larry F. Brown

Mining has been the mainstay of the Woods Creek Valley for more than a century. The head of the valley is at the Continental Divide, about 50 miles west of Denver, Colorado. First, it was the quest for gold and silver that drew people to the valley. Then, when molybdenum was classified as a strategic metal by the U. S. Government during World War I, it was the valley's molybdenum mineralization which attracted the most attention. Molybdenum is used primarily as an alloying material in superior grades of steel. Circumstances responsible for providing the label "Urad" are unknown, but Urad is variously reported to be an acronym for "Uranium Research and Development" or "Uranium Research of America Division". The search for uranium was fruitless as no ore grade uranium exists in this area. The moly orebody was first developed and mined by the Primos Exploration Company from 1914 to 1919. During World War II, the mine was purchased by the government and turned over to the Molybdenum Corporation of America to operate. In 1963 AMAX Inc. purchased the property for $2 million. After spending nearly $30 million for exploration and development, AMAX put the mine into production again in 1967.

Jan 1, 1984

In practice a sampling solution is a compromise of many requirements: the sample should be representative; the sampling system should also be reliable, less than 95 per cent availability restricts the use of the assayed sample for process control purposes; no sample is the worst sample, and investment costs and installation space/layout are frequently a restriction. For instance, online X-ray analysers for process control introduce a delimitation error by the nature of X-ray physics. Thus only in special cases a relative accuracy better than three per cent relative, as one standard deviation, is achieved. A sampling system for process control needs not to be, as representative, for so many sample properties, as one for composite laboratory analysis samples. Sampling system maintenance is also an important issue. There are many sampling systems in the industry which have been difficult to maintain and are in disuse for lack of resources or incentives to keep them running. Pierre Gy developed the most generally accepted sampling theory. One of the main principles is that all particles in a one-dimensional process stream should have equal chances of being included into the sample. A correctly designed and operated transversing cutter comes close to this goal but has limitations in temporal representativity. For slurries an acceptable solution in many cases is to use a fixed vertical cutter(s) in a position where the slurry is well-mixed by turbulence and other means. For online analysis, reliability problems are mostly related to faulty design or installation of the piping system to the analyser. Properties of material processed, process flow sheet and piping details before and after the sampler have to be taken into account when deciding on which sampling arrangement is appropriate. Guidelines and some solutions to these issues are presented in this paper.

Mar 1, 2010

By Jorge Amaya, Nelson Morales Varela, Francisco Saavedra, Gonzalo Nelis, René Gómez

Precedence constraints are broadly used in mathematical models and algorithms for mine planning to model, for example, slope angles in open pit operations or connectivity in underground mines. Unfortunately, these constraints do not capture relevant geometrical aspects for the design of the mine like minimum bottom space of pits or smoothness of the economic envelope in block caves. In this work, we present different approaches that utilize precedence constraints generating economic envelops that are more suitable for design purposes. The numerical experiences show that the proposed techniques produce high value envelops with better geometrical properties and that the methods proposed can be computed efficiently.

Jun 25, 2023

By J Lööw, M Nygren, E Segerstedt, L Abrahamsson

The purpose of the paper is to discuss socially sustainable development in the mining industry and the communities surrounding the mines. The discussions are based on results from a prestudy and literature review on mining and sustainable development conducted during 2013–2014 at Luleå University of Technology in Sweden. ‘A social licence to mine’ is important for the mining industry, but the social dimension is a relatively underdeveloped dimension when it comes to sustainable development in general and the mining industry in particular, one reason probably being the lack of effective methods for capturing social impacts. The mining industry and the surrounding communities face many challenges that provide both possibilities and obstacles to socially sustainable development; eg aspects such as gender, work conditions and cultural aspects. For example, a strong mining workplace culture and community identity can create strong cohesion but also lead to excluding certain groups, rejecting new ideas and reinforcing obsolete values. Other challenges include recruitment, as well as health and safety in relation to an increased use of fly-in-fly-out, contractors and automation of mining. Some challenges relate to the effects of fluctuations in the mining market. There is a lack of research that links attitudes, policies and activities within companies to their impact on the wider community, and vice versa. Future research should also include the development of methods and indicators for social sustainability relevant for mining – in other words: how do mining companies get ‘a social licence to mine’?CITATION:Abrahamsson, L, Lööw, J, Nygren, M and Segerstedt, E, 2015. How to get a social licence to mine, in Proceedings Third International Future Mining Conference, pp 125–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By M. Riddell

This paper describes the incipient heatings that occurred below ground in the High Main and Main seams at the mine between the years 1963 and 1966. The possible causes, effects and activities associated with such heatings are discussed in an attempt to establish the precautions necessary to minimize such occurrences. The assessment of as many "norms" as possible is made to enable the earliest detection and level of activity to be determined.

May 23, 1905

By D. B. Gillies

IN 1938 the Republic Steel Corp. announced that it had leased the ore mines and other property of the Witherbee Sherman Corp. at Port Henry, N. Y. The announcement brought forth an interesting reaction. Two questions were asked repeatedly: (1) Is the iron product high grade? (2) Is there a substantial reserve? The answer to both questions was and is a decided and emphatic "Yes."

Jan 1, 1943

By Dario Libano, Franz-Werner Gerressen

"Diaphragm walls are known as underground structural elements commonly used for retention systems and permanent foundation walls or elements. Of course they can also be used as deep groundwater barriers. This paper will focus on the construction work in an urban area like Sao Paulo. The Line 5 of Metro Sao Paulo is one of four network expansion projects undertaken at the same time. The projects will cover various areas of the city. The Line 5 on São Paulo’s south-side will be extended 7.1mi (11.5km) to serve 770,000 riders per day, stretching a total of 12.4mi (19.9km) along 17 stations. The extension line will facilitate access to the city’s central section and the commercial and hospital districts located along the line. The Brooklin Station, subject of this paper, had to be carried out in a special five shaft shape design, shaft diameter 131ft (40m) each, without using ground anchors. A focus will be taken on the special requirements of the installation of the arrows as well as on the specialties of installation for the shaft shaped layout. Therefore, it was required to install a 3.3ft (1,000mm) diaphragm wall using a specific layout especially in the connecting sections of the shafts, the so called arrows, to provide a bearing area for the struts. Maximum wall depth was about 121ft (37m); the total volume was about 20,060 cubic yard (15,337m³). The paper will describe the construction method and the sequence of activities required for the construction of this diaphragm wall using a combination of hydraulic grab and trench cutter system.INTRODUCTIONThe Line 5 Extension, in the city of Sao Paulo/Brazil, is currently the most important investment in public transport by Sao Paulo state’s government. It will connect the south part of the city to the city center, crossing through four other major METRO lines and stations, all currently in operation. The extension includes a new parking yard for the trains and 11 new stations. The Brooklin Station is one of the new stations and has a unique geometry of five secant shafts. The station should open and operate in 2016.The original design included constructing five secant shafts stabilized by two plastic slurry walls using conventional grab technology. One of them was to contain the contamination plumes in the neighborhood and the other for temporary support to enable the excavation of the shafts. The final retaining wall design was reviewed and changed to a concrete structural diaphragm wall. The reason of design change was as well the reduction of construction time of the shafts by half to meet the schedule as to avoid dewatering effects in a geological region characterized by Quaternary sediments and environmental contamination plumes. It was the first time that a trench cutter (hydromill) was used in such a situation in Brazil. The cutter increased the quality of the joints by overcutting, and decreased the probability of having seepage into the shafts. The cutter created a seepage barrier and avoided movement of contamination."

Jan 1, 2017

By Emad W. Shublaq

Contractual site plans are implemented for executing pile foundations (5 x 5) at segmental concrete bridge. Project schedule demands have forced the contractor to find out the most economical procedure in achieving the goal. This paper presents a site management technique which is applied by the Contractor. This was found to be fruitful and as much as 60% saving was gained.

Jan 1, 1992