Search Documents

By H. K. Lin

The effect of metallic iron fines on froth flotation of a sulfide ore was examined by comparing the flotation results with and without iron fines present in the flotation feed. Mild steel and ceramic laboratory ball mills were used to grind 600 g sulfide ore charges. The mild steel ball mill generated approximately 4.6 g of iron fines (0.8% of the ore charge mass) when grinding to a product size of 80% passing 200 mesh (75 mm). When a low dosage of a weak xanthate collector was used in flotation, the impact of the iron fines on sulfide flotation was marked. Higher dosages of stronger xanthate collectors rendered the impact of the iron fines much less significant. Consumption of the collectors by the powdery iron fines is believed to cause the differences observed in the flotation results. A galvanic effect on flotation was not evident in this study. The impact of the iron fines on silicates depression was also examined.

Jan 1, 2008

By Janice K. Means

The purpose of this paper is to provide the seminar attendee with: information on pipeline construction, operation and standards to better equip him (or her) to analyze the ultimate effect of blasting stress on pipelines; an introduction to the analysis of blasting effects to pipelines using the American Gas Association analysis method; and; supplemental sources useful in the analysis of blasting effects to steel pipelines, and, in particular, on natural gas pipelines.

Jan 1, 1992

By George C. Coupland

Ecstall Mining Limited, a wholly owned subsidiary of Texas Gulf Sulphur Company, is the owner and operator of the Kidd Creek Mine including the concentrator complex located near Timmins, Ontario. Canada, approximately 450 miles north of Toronto. The mine, concentrator and Timmins form a triangular arrangement with a 17-mile rail link connecting the mine and concentrator and both of these facilities 18 and 14 miles respectively by road from Timmins. A core drilling program in the spring of 1964 established the presence of a large massive sulphide orebody which was to become the Kidd Creek Mine. Texas Gulf Sulphur had been conducting an intensive search for base metal in various parts of Northern Ontario and Quebec since 1957. Of several thousand anomalies detected in airborne electromagnetic surveys, several hundred warranted ground inspection, but only one of more than sixty drilled became a commercial orebody, the Kidd Creek Mine. The geophysical exploration work has been well covered in a paper written and presented by Van Donohoo, presently a Vice-President of T.G.S., at the American Mining Congress in San Francisco in October 1969. GEOLOGY The orebody lies within a series of overturned rhyolitic flows and pyroelastics with a major peridotite intrusive to the east. The hangingwall and footwall are composed chiefly of intermediate volcanics, andesite and dacite. The southern end of the orebody appears to terminate abruptly against greywacke while the north end is bifurcated and the structure obscured.

Jan 1, 1970

By R. Flatabø, K-E. Johansen, L. Hunsbedt, P. M. Cowx, J. A. Bustnes

Eramet and Tinfos are two producers of manganese alloys in Norway, which have worked hard for several decades to improve both the internal and external environment. Furnaces producing ferro- and silico- manganese alloys generate large amounts of off-gas that contains substantial amounts of dust, heavy metals and organic by-products. The dust is separated from the gas in venturi scrubbers by washing with water. The water is cleaned and recirculated, and the surplus water coming from moisture in the raw materials, is discharged to the adjacent fjords after further treatment. Emission figures show that the discharge of suspended solids, manganese, zinc and PAH (polycyclic aromatic hydrocarbons) have been reduced substantially over the last three decades as a result of process improvements and installation of state of the art environmental control measures. The two plants were the first world wide to install mercury cleaning of the off-gases from the furnaces. Mercury emission reduction has exceeded 90%. Concerning other environmental issues, such as utilisation of off-gases for energy recovery and chemical purposes, both plants have achieved good results. Major effort in the environmental work has come from the plants themselves, but other players like FFF, The Norwegian Ferroalloy Producers Research Association, and SFT, The Norwegian Pollution Control Authority, have contributed to the achieved results.

Jan 1, 2007

By Matthew Grzelak, Gulsah Erinc, David R. Chapman

"The third phase of the Bagram Drainage System project at Bagram Air Force Base in Afghanistan included construction of a shallow, 540-m long, 1.8-m inside diameter drainage tunnel. The tunnel penetrated mostly stiff to hard clayey and silty soils. The contractor’s Value Engineering Change Proposal (VECP) to use pipe-jacking with a microtunnel boring machine (MTBM) instead of the specified two-pass Earth Pressure Balance method was evaluated and supported using hand calculations. Contractor support was provided throughout the project by providing design reviews and instrumentation monitoring during construction. This paper compares the value-engineering proposal to the specified method and describes the construction conditions encountered. INTRODUCTION As part of a larger improvement project at the Bagram Air Force Base in Afghanistan, a shallow, 540-m long, 1.8-m inside diameter drainage tunnel was constructed to provide additional capacity for Coyote Creek to pass below several critical structures, including taxiways and the main runway, for mitigation of recurring flooding (see Figures 1 and 2). Overburden over the tunnel crown ranged from about 3 m to 5.5 m. An existing cast-in-place twin barrel concrete culvert runs approximately parallel to the new tunnel and is within about 8 m at its closest point. The contractor’s Value Engineering Change Proposal (VECP) to the specified two-pass Earth Pressure Balance (EPB) method (steel ribs and lagging or steel liner plate with a carrier pipe later grouted in-place) called for installation of the required drainage pipe by pipe-jacking (one-pass installation) using a slurry microtunnel boring machine (MTBM). The critical nature of the operations at the air base resulted in significant construction coordination challenges and a greater than usual need to avoid excessive settlements. Substantial restrictions were placed on drilling of investigative borings and installing instrumentation near runways and taxiways due to drill mast height. The prime contractor was SERKA TAAHHUT INSAAT A. S. (SERKA), the microtunneling subcontractor was Ludwig Pfeiffer Microtunnel GmbH & Co.KG (Pfeiffer), the jacking pipe designer was Gollwitzer Pipe and Shaft Technology GmbH (Gollwitzer), and the contractor’s tunnel engineer was Lachel & Associates, Inc. (Lachel). Lachel provided contractor support throughout the project including preparation of a VECP/Design Summary (including interpretation of existing and new geotechnical information), design reviews for jacking pipe, estimating settlement of an existing drainage structure above the new tunnel, and instrumentation planning, monitoring, and analysis during construction."

Jan 1, 2016

By J. Shanks

In 1920 the writer presented some notes, embodying his experience with storage-battery locomotives as main under-ground haulage-motors at Brazeau collieries. (1) Since that date these motors have stood up well to the test of maximum output and heavy overloads, having accomplished all that was expected of them. The notes presented in 1920 gave a brief description of the conditions under which these motors were working at Brazeau collieries, also the cost, per ton mile, of operating them. The cost per ton mile has since then been appreciably reduced, by working the locomotives nearly to capacity and under more ideal haulage conditions, on both shifts. It is not the intention of the writer to repeat what was written in 1920, but rather to give members the benefit of his experience in operating different types or designs of locomotives; to draw their attention to the drawbacks of some designs, and to the improvements made in some of the more recent storage-battery locomotives put on the market, as regards efficiency, upkeep, and safety. Because of their flexibility storage-battery locomotives have advantages over any other type of haulage, where grades are suitable to their use. The number in use in the mines in the United States has increased enormously during the past few years, and this method of haulage is, at the present time, attracting the attention of British and Continental mining engineers.

Jan 1, 1924

By L. Adler

The proper transfer of roof loads from props and bolts to ribs and pillars can result in appreciable savings. The author shows how to plan such load reduction in underground mines. For openings in bedded rocks, analyzed by simple beam theory, it has been shown that roof loads can be shifted from one support to another.&apos; This transfer is effected by controlling the relative deflection of adjacent supports. If this action is used to reduce loads in the props or bolts and increase them in the ribs or pillars, it could be productive of economies averaging 30 pct. Such savings can be realized by: 1) using smaller artifical supports such as props and bolts, and 2) increasing loads in the rib to induce eventual failure for longwall caving. Since the rib is relatively load-insensitive, it provides a natural load sink. However, caution must be used in applying such permissive deflections, for while the supports are being handled properly, the stresses in the roof itself are very sensitive to such manipulations.1 An underground opening overlain by a relatively thin immediate roof, and a thick main roof, is usually laid out as shown in Fig. 1. The total open span (T) between pillars or ribs is calculated on the basis of the main roof, and the secondary spans (L) on the basis of the immediate roof, so that a complete accounting of the existing loads is made. For this purpose the immediate roof is treated as a uniformly loaded continous beam, which is an indeterminate structure as shown in Fig. 2(A). The term systematic supports places the following two restrictions on the continuous beam: 1) Spans between all supports are equal: uniformity of spans. 2) Loads on all supports (excepting ribs) are equal: uniformity of supports. The usual mode of analysis of such a structure by beam theory is to divide it up into a series of simply supported beams with end moments as shown in Fig. 2(B)2 The problem now is to transfer a maximum roof load to the rib from the span immediately adjacent to it by permitting its support to deflect, and yet not fail the roof. Once this has been done, the load can be equalized on all other supports by permitting further degrees of relative deflection. It is necessary, therefore, to determine an expression for the constant load on each support, and the required deflections, in terms of properties of the roof. From Fig. 1: T/L0 = No and T/L = N [1] Where: T = allowable span of main roof, ft. (Calculated from S = Mc/l) S is allowable modulus of rupture, psi. M is maximum moment, lb-ft (in this case wT2/12). c is distance from neutral axis to extreme fiber, ft. I is moment of inertia with respect to the neutral axis, ft4. L,, = allowable span of immediate roof, ft (calculated as was T). L = actual span of immediate roof, ft. N0 and N are pure numbers where No < N and N is the integer just higher than Nu. For example: If T =100 ft and L0 - 15 ft 100 N0 =100/15= 6.667 . . .N= 7 L = T/N = 100/7 = 14.28 ft Consequently N = No + n where n is a positive fraction i.e.: 0< n < 1 Since from Eq. 1, T = NL = N0L0 Lo /L = N/No = N/N-n

Jan 1, 1961

By M. Buxton

Sensor derived data can add value across the mining operating chain ranging from resource definition, extraction, pre ? concentration, mineral process monitoring and assessment of product quality. Most documented studies on the use of sensors in mining focus on specific technologies for specific applications. These studies do not take into account different aims, objectives and operating conditions at different steps in the value chain. The first part of this contribution assesses key physical performance and discriminatory requirements of sensors applied in each portion of the mining value chain. The second part proposes a framework of methods for quantifying the value added by additional sensor information. Integrating the sensor based technology and the economic value quantification allows for both, designing an economically optimal sensor monitoring network along the whole mining value chain and optimizing efficiencies. Illustrative studies demonstrate the significant economic benefits, in particular in reduction of exploration expenditures, increase in extraction efficiencies, increase in ore product quality and improvement of processing efficiencies.

Feb 27, 2013

By D. Mohapatra

The possibility of using 2,2,4-trimethyl-1,3-pentanediol dissolved in tetrachloromethane as extractant for boron recovery is discussed. The parameters optimized for this purpose are contact time, boron concentration in the aqueous phase, extractant concentration, equilibrium pH and phase ratio. NaOH is used as stripping agent for boron recovery from the loaded organic phase. Boron extraction is found to be a slow process (equilibrium time 20 minutes) compared to boron stripping, which is reasonably fast (equilibrium time 5 min). Maximum boron extraction is possible at a broad pH range from 1.0 to 6.0. Using 1.0M extractant concentration, a 1:1 phase ratio (organic: aqueous) and two stages, ~99% boron extraction is achieved. More than 97% boron stripping is possible using 0.5M NaOH at a 1:1 (organic: aqueous) phase ratio in two stages. Overall, a 95.6% boron recovery was achieved. Loss of solvent into the aqueous phase and co-extraction of Ca, Na and K into the organic phase at higher equilibrium pH are two major concerns in his process.

Jan 1, 2008

By P. J. Brereton-Stiles, C. J. Hockaday, I. J. Barker, M. S. Rennie

This paper reports on studies that have been done on the electrical conduction in silicon, ferro silicon, and charge chrome furnaces. A system has been developed that can distinguish between normal resistive conduction and arcing, and this was used to quantify in particular the relative amount of arcing that takes place in these furnaces. It was found that silicon and ferro silicon behave similarly and exhibit a relatively large amount of arcing. Charge chrome on the other hand exhibits considerably less arcing, and the extent of this arcing is highly correlated with the tapping of the furnace. The arcing measurements can also be used online in the control of the furnace, both for the electrodes and electrical circuit, and for the raw materials.

Jan 1, 2007

By S Smit, P J. J Strobo

ZINIFEX Century Mine is a zinc, lead and silver concentrate producer. Flotation is the primary method of minerals separation in this circuit. The flotation circuit is quite large with 79 flotation cells. The levels in each of these interconnected cells are controlled at more than 45 level control stations. Due to the multivariable interaction throughout the circuit, good level control was found to be difficult to achieve by just using normal Proportional-Integral-Derivative (PID) control. As a first step in advanced process control, the FloatStar Level Stabiliser, a multivariable controller developed specifically for flotation circuits, has been commissioned at Century mine to solve the level control problems. The first section of this paper therefore discusses and shows the results and improvements obtained by using the FloatStar level stabiliser. The results and benefits of the FloatStar Flow Optimiser are discussed in the second section of this paper.

Jan 1, 2004

By L. J. Olivier

The possible closure and subsequent flooding of South Deep Gold Mine?s (SD) neighbouring Randfontein Estates Limited No. 4 Shaft (REL 4) necessitated the construction of five concrete plugs in the connecting tunnels to prevent the ingress of groundwater into REL4 from flooding SD. This paper describes the proposed controlled flooding of REL 4, the planned in-service monitoring of the five plugs and the water barrier between REL 4 and South Deep Mine, and the long-term maintenance of the plugs and rock mass in the immediate vicinity of the plugs.

Jan 1, 2006

By N. Powell, R. J. Pine

An algorithm is proposed for updating the probability of slope failure on the basis of sequential testing using Bayesian probability theory. The approach is novel and computationally straightforward since, unlike other methods, updating of the probability of failure is carried out directly. This is because the probability is treated as a random variable whereas other methods have considered it as a purely deterministic value or as a function of shear strength parameters that are updated individually. The prior information required for the Bayesian analysis is obtained by a conventional probabilistic analysis. An exponential distribution is then used for the probability of failure, applying the principle of maximum entropy. This distribution is continually updated for individual slope cells, where repetitive excavation creates several such cells and a corresponding series of Bayesian estimates of the probability of failure is obtained. The approach is applicable to most simulations but there are limitations on its use. A more mathematically rigorous refinement using the beta distribution is currently under development

Apr 1, 1996

By D F. S Natusch, R J. Hooper

Recent lignite investigations indicate their potential as a strategic long-term fuel resource. This potential however would be determined not only by lignite quantity and quality, but also by economic, physical and social resources required to support it. The following discussion uses the example of a typical lignite mining operation to review the major resource requirements. While recognising that the implications of supplying those resources may be as important as their actual existence, this paper has purposely omitted such discussion as this will be one of the main target areas for the next phase of investigations.

Jan 1, 1983

By Luis Carrera Naranjo

El presente texto señala la topografía, geología regional, estratigrafía, fisiografía, caracteres morfológicos, mineralógicos y genéticos, y la clasificación según su proceso de formación del yacimiento de la región Morococha. La topografía de esta región es variada y rica en cuanto formaciones geológicas se refiere, dado sus orígenes y edades respectivas. Su estratigrafía comprende una columna geológica, la cual está compuesta por rocas sedimentarias, y extrusivas que van desde el periodo Cuaternario hasta el Terciario. Las formaciones encontradas en la región son las filitas excelsior, volcánicas Catalina, formación Mitu, calizas Potosí, formación Santo Toribio-Buena Ventura, formación Machay, las capars rojas de Casapalca, la diorita de Anticona y monzonita cuarcífera de Morococha. Asimismo tiene dos sistemas de fallas: longitudinal y transversal. Las especies metalíferas de mayor abundancia son: la pirita, tenantita, tetrahedrita, chalcopirita, enargíta, blenda, magnetíta y galena. Mientras que las de menor abundancia son: estefanita, especularita, phrotita, marcasita y muy raramente: aíkenita; burnonita, cubanita, jamesonita, luzonita y molibdenita. Finalmente, entre las características estructurales de depósito tenemos: las vetas y los mantos, considerando entre los mantos algunos subtipos o variedades estructurales. También existe una tercera clase de estructura de depósitos minerales, que son lo que están constítuídos por varios depósitos agrupados en forma localizada y se conocen como el "0re -Clusters" o "Archipiélago".

Jul 20, 1960

By Frederic Vanderoost

Actualmente, el manejo adecuado de las informaciones geológicas en el sector minero optimiza recursos y maximiza resultados. En ese sentido, el presente texto señala la implantación de un conjunto de herramientas para la administración de banco de datos geológicos, de forma corporativa y manteniendo un informe central de datos. Dichas herramientas se basan en sistemas comerciales de base de datos como Oracle, Microsoft SQL Server y Sybase, los cuales garantizan agilidad, flexibilidad y capacidad de almacenamiento para el manejo de informaciones adecuadas y las operaciones típicas de la industria minera. Asimismo, se presenta estudios de casos, analizando sus ventajas, limitaciones y dificultades encontradas en una mina.

Aug 25, 2002

Kinetic Study on the Leaching of Vanadium from LD Converter Slag Using Sulfuric Acid In order to reduce the environmental impact due to land disposal of LD (Linz-Donawitz) converter slag from steelmaking plant and to valorise this waste material, an acid leaching study was carried out to assess the effect of several parameters on the kinetics of vanadium dissolution. The characterisation and morphology of the feed investigated using XRD, XRF. The factors influencing leaching vanadium such as particle size, temperature, slurry density and the concentration of sulfuric acid were investigated and optimised. The maximum vanadium recovery about 95 per cent achieved at 70¦C, S/L: 1/15, acid concentration: 3M and for 150 minutes of leaching time. The dissolution of vanadium in sulfuric acid shows that there are two stages in the kinetics of leaching. At the first 15&nbsp;minutes, there is a sharp increase in the amount of vanadium extracted and at longer leaching time, the extraction increase slightly. In the present work, the shrinking core model (SCM) was used to describe the acid leaching of vanadium compounds. A summary of the controlling regimes in the SCM are examined below for short time (less than 12 min.) and long time (more than 30 min.) stages. So, it was found that the kinetics of leaching in both stages is controlled by solid product diffusion regime.

Sep 13, 2010

Influence of Grinding Media on the Flotation of Carbonate Using Sodium Oleate as Collector

Sep 13, 2010

By Stephen C. Tadolini

The International Ground Control Conference in Mining has always provided an open forum for the publication, presentation, discussion, and often heated debate on roof bolting systems mostly with attention to how, when, and why they work. During the last 24 Conferences at least 170 papers have been presented by International Experts on these ?simple? devices that range in length from 30-inches to 20 ft and from 5/8 to 2 inches in diameter. Roof bolts are primarily mechanically anchored, glued, cemented, or driven. Bolts are placed vertically, angled, or tied together with special fixtures (trusses and slings). They have been termed active, passive, stick-slip, and several other descriptive acronyms or mining slang expressions. This retrospective paper will present the changes in bolt types and usage, point out some of the biggest myths and hail the most significant advances (according to the authors? opinions of course).

Jan 1, 2006

By D G. Jefferies

This paper covers National Grid's role in the electricity market, the growth of competition in both generation and supply in that market, and the resulting impact on fuel usage, prices and the environment. It also considers other, external influencing factors on the electricity supply industry, as well as the growing trend towards globalization.

Jan 12, 1997