Search Documents

By T. Salman

Most authorities agree that the dissolution of gold from an ore takes place according to the Elsner equation first stated in 1846. The main requirements for the dissolution reaction to proceed are:(1) that the gold be clean.(2) that the gold be exposed to the solution.(3) that the cyanide solution be active, i.e., not over loaded with impurities which could retard or inhibit the reaction.(4) that an adequate supply of oxygen be available (from air).When the above conditions are met, cyanidation becomes basically a mechanical operation.Minerals such as quartz, calcium carbonate are relatively inert to cyanide though they may give rise to mechanical troubles. Most ores present an assortment of chemical problems, depending upon the constituent present, which react to the solution to varying degrees. It should be borne in mind that minerals which are disturbing to the operation, though present in small amounts, usually exceed the weight of the gold by several hundred times. In addition, the application of flotation and other forms of concentration to gold ores, previous to cyanidation, concentrates not only the gold, but also the other heavy minerals and these complicate the chemistry of the process.

Jan 1, 1975

By Harry Perry

U. S. consumption of sulfur and sulfur products is expected to increase at a rate of 8 percent per year between now and 1980, largely as a result of their use in fertilizer markets. World consumption is also increasing rapidly, but at a-lower rate, about 6-percent per year. In 1965, sulfur recovered in the United States from purification of natural gas; nearly doubled from the 1956-1960 average; production from pyrites declined; and production of elemental sulfur increased 15 percent. Concern about air pollution resulting from sulfur oxides produced from the combustion of fossil fuel has lead to intensive research on methods of removal before combustion, during combustion (in-process methods), and from the resulting flue gases. If all the sulfur in fossill fuels were recovered, more sulfur products would be produced than were consumed in the United States in 1965. Removal of sulfur from coal before combustion could result in a product sufficiently-high in sulfur to be a suitable raw material for sulfuric acid manufacture. In-process methods produce solid sulfates, some of which may have commercial value. Flue gas removal' methods for sulfur oxidest generally result in the production of a byproduct either of sulfuric acid or sulfur. The projected sale of these materials significantly lowers the anticipated cost of sulfur dioxides pollution abatement. Alternate methods for sulfur dioxide reduction are discussed. The various proposed processes are described and costs are given for the various methods for which estimates have been made.

Jan 1, 1967

By Mark Colwell, Christopher Mark

This paper summarises the results of a research project whose goal was to provide the Australian coal industry with a rib support design methodology and software tool that could be utilised by suitably qualified colliery staff. The project was primarily funded by Australian Coal Association Research Program (ACARP) and further supported by several Australian longwall operations. The outcome of the project is a design methodology and software tool called, Analysis and Design of Rib Support (ADRS). ADRS is an empirical technique, which recognises that several geotechnical and design factors affect ribline performance and in addition that operational and safety issues essentially dictate the level of performance required. Therefore, the design recommendations associated with ADRS are specific to the Australian coal industry; however the procedure(s) for data collection and analysis could be applied to other countries' 'underground coal industries. Case history data were compiled from 34 longwall and two bord and pillar operations resulting in 204 case histories with each case history data set being defined by approximately 130 individual data fields. In addition monitoring (incorporating stress cells and extensometers) was undertaken at 10 collieries to assess and quantify the effectiveness of different rib support patterns and hardware on rib performance. The monitoring sites allowed for an improved understanding of the mechanisms of rib failure and degradation in terms of its interaction with the installed support and at the various stages of the mining cycle. The design methodology deals with both mains development and gateroad development specific to Australian longwall mines. This paper focuses on longwall gateroads subjected to abutment loading and in particular the travel road which becomes the tailgate of the subsequent panel. The statistical analyses associated with these cases suggested that the level of rib support should be based primarily on the development height and the pillar stress level. The ADRS software guides users through the design process, allowing them to develop rib support plans based on sound science and a broad base of in-mine experience To the best of the authors’ knowledge ADRS is the first systematic rib support design technique to be developed for any country’s underground coal industry. The development and use of empirical models in mining have substantially contributed to improving safety and productivity. ADRS further demonstrates that empirical techniques are particularly relevant and beneficial in dealing with the complexities of geotechnical design associated with underground coal mining.

Jan 6, 2008

By Claudio Flores Martinez

The prospect of accomplishing economically and scientifically profitable deep-sea mineral mining within this decade or the next one is of particular interest to the emerging discipline of astrobiology which is concerned with the origin, distribution and future of life in the Universe. Several planetary bodies within our own Solar System such as Jupiter’s moon Europa and Saturn’s Enceladus now appear to be potentially habitable, or life-friendly, in terms of the three prerequisites for life as we know it: a sustained body of liquid water, biogenic elements (C, H, N, O, P, S) and energy sources to fuel metabolic reactions. Europa, for instance, possesses a global subsurface ocean, believed to be up to 100 km in depth, hidden beneath a kilometer-wide ice-sheet. A silicate mantle is directly interacting with a cold, aphotic ocean in which tidal forces might drive geological seafloor activity that results in the creation of hydrothermal systems. These locales are commonly hypothesized to be the cradles for an alternate origin of life on Europa. Especially alkaline hydrothermal springs, as found at Lost City, have been at the center of modeling the prebiological evolutionary dynamics preceding cellular life. Serpentinization-like reactions are also possibly fueling metabolic networks in putative microbial communities found in the oceans of the icy moos. Major space agencies around the globe are planning future space missions aimed at exploring and eventually characterizing potential life forms in these habitats. The technology needed for this exploration effort resembles the requirements for a successful deep-sea mineral mining industry: highly efficient AUVs (also equipped with biologically-oriented instrumentation), swarm robotics, landers, seafloor rovers and general high-pressure, cold temperature extreme environment engineering. Interestingly, science questions of deep-sea mineral mining and astrobiology converge too: the hypothesis of life originating at hydrothermal systems, the biogeographical distribution of species among these environments, adaptations of extremophilic organisms across the three domains of life and adequate autonomous robotic systems to assess the complexity of deep-sea biological communities. This presentation attempts to present a two-fold view of advanced planetary exploration that relates to a sustainable vision of deep-sea mineral mining: charting our oceans and developing technologies least harmful to endemic biology can propel the design and prototyping of future robotic planetary probes bound for aquatic missions on alien moons. Space industry, government and public interest towards a broadened planetary perspective on deep-sea mineral mining is promoted by addressing an astrobiological rationale of this endeavor.

Sep 1, 2014

By Ponisseril Somasundaran, H-L. Chen, University of Athens, D. R. Nagaraj, Zhonghua Pan, Jing Wang

Gums are often used as depressants for talceous gangue minerals in the flotation of nickel and platinum bearing ores. However, the mechanisms of gum adsorption on talc are not clearly established. In this work, adsorption of guar gum at the talc-solution interface is investigated using spectroscopic and allied techniques. Guar gum adsorption on talc is not affected significantly by changes in solution conditions such as pH and ionic strength. Electrokinetic studies showed that guar gum decreased the negative zeta potential of talc but did not reverse the charge. Fluorescence spectroscopy studies conducted to investigate the role of hydrophobic bonding using pyrene and dansyl probes showed no evidence of the formation of hydrophobic domains at talc-aqueous interface. Urea, a hydrogen bond breaker, reduced the adsorption of guar on talc to the same extent as that for guar/alumina system, in which hydrogen bond plays an important role. All of the above results suggest that one of the main driving forces for guar adsorption on talc is hydrogen bonding rather than electrostatic or hydrophobic force.

Jan 1, 2003

By Peter N. Holtham, Mary M. Ng

"Resistivity measurements of minerals in the laboratory are commonly made with a low DC voltage source. Common test voltages specified in the ASTM Standard D257 are 100, 250, 500, 1000, 2500, 5000, 10000 and 15000 V, however 100 and 500 V are the most frequently used. Resistivity results obtained in the laboratory have been used to infer the electrical behaviour of minerals undergoing electrostatic separation. However because the voltages employed in electrostatic separation in the plant are of the order of thousands of volts, typically greater than 15000 V, whether the laboratory results are applicable as a predictor of plant performance is a critical question. It is unclear whether resistivity values taken at a low voltage are characteristic of those seen in electrostatic separation, in which the minerals are exposed to a much higher voltage. No definitive answer could be found in the literature.In this work, the resistivities of zircon, rutile and ilmenite were measured in a corona field for the first time. The measurement principle was based on a technique developed to measure fly ash resistivity in electrostatic precipitators, however the test apparatus and findings are novel.Resistivities of rutile and zircon were found to be easy to measure. The values measured in a corona field were several orders of magnitude less than those obtained with a dc voltage of 100 V. Evidence of back corona was observed with zircon. When the voltage drop was greater than the sample layer could withstand a localised electrical stress developed, resulting in a voltage breakdown, at which point a sudden surge of corona current (back corona) was detected in the sample layer. Rutile, on the other hand, exposed to the same conditions as that of zircon (i.e. same temperature and applied voltage) did not exhibit any sign of back corona. Its resistivity across the range of test voltages (14 to 33 kV) remained fairly constant."

Jan 1, 2003

By T. V. Chnyrenkova, J. Troncoso, V. A. Luganov, G. P. Kluev

"Arsenic-gold bearing ores are used as flux in smelting or are leached out with extraction of gold. For decreasing arsenic content in processed materials and for breaking up the lattice and opening up of gold the raw materials are roasted. Some regularity was established for sulfidizing of arsenic bearing compounds in a presence of pyrite and for oxidation of ores and concentrates in the presence of soda.This article analyses the results of laboratory and pilot testing of dissociating and oxidizing roasting of gold-arsenic bearing concentrates. During the dissociation roasting under vacuum arsenic is sublimated into elemental and sulfide forms. This process allows minimizing the negative influence on the environment but requires costly engineering solutions. Roasting in a limited quantity of oxygen in the gaseous phase makes it possible to sublimate arsenic in the form of oxides and sulfides and may be carried out in fluid bed furnaces."

Jan 1, 2003

By P. K. Sen, Mrinal K. Ghose

Tailing slurry is usually abrasive and possesses high viscosity. This paper examines the existing iron ore beneficiation process and focuses on some of the key environmental issues related to the disposal of tailings. It identifies that almost 32% of the iron ore extracted ends up as tailings and they are usually disposed in slurry form in tailing ponds. By the year 2000, 27 Mt of iron ore tailings were generated in India, which has become one of the biggest waste handling problems to the industry. Characteristics of the tailings vary widely. So the physical nature of tailings cannot be considered separately in isolation without considering the mill effluent from the beneficiation plant. In the present investigation, studies were carried out in three iron ore mines in India to evaluate the characteristics of tailings from the beneficiation plant. The tailing samples were collected from different locations during a time period of one year and analyzed. The results will be discussed and the characteristics of the tailings have been evaluated. The disposal system of tailings at the three mines was evaluated. The research on the settling characteristics of tailings indicates that the area provided in the existing tailing ponds in India is much more than that of the experimental results. This paper concludes that sedimentation tests are essential to design appropriate tailings pond with respect to size. In the proposed scheme it is suggested that an additional unit process, i.e. sedimentation tank be added to the process before the disposal of tailings to the tailing pond.

Jan 1, 2003

By Jim Petrie, Mary Stewart, Damien Giurco

This paper describes a generic approach to analysing the environmental and economic performance of a generic global mineral/metal value chain, with the express view of improving the quality of prospective decision-making within the industry in order to ensure more sustainable outcomes. As a point of departure we propose that it is not possible to place metals in the context of the sustainable development of society without paying due regard to the entire metals value chain. Thus, the starting point for this analysis is the development of a global stocks flows and transformations model, for the metal of interest. Any aspect of the value chain, e.g. “metals refining, “goods manufacture”, “use and disposal”, can be assessed, either relative to other stages in the value chain, or in more detail by focusing on the technologies used within that stage. The use of this model as a decision support tool is explored here for the case of copper. Both primary and secondary production routes are enumerated, covering a range of processes, for seven distinct geographic regions around the globe. The value of the modelling approach is explored for different energy mixes. In particular, the case study examines the impact of increased recycling on the (re) distribution of global and regional environmental impacts for technologies-in-place in these different regions. The aim of these case studies is to highlight to the minerals processing and metals refining industries their potential role in a more sustainable global society.

Jan 1, 2003

By J. Tian

"BHP Billiton carried out a pre-feasibility study on the LanPing zinc deposit to evaluate the possibility to jointly develop the zinc deposit into a large-scale zinc project with their Chinese partner. The unique characteristics of the complex LanPing zinc orebody and ore are 1) smithsonite (ZnCO3) as one of major zinc bearing mineral besides sphalerite, 2) varying and irregular oxidation degree of zinc (0 ~ +90%) in the different zone and depth of the deposit, and 3) varying host gangue from limestone/calcite dominant to quartz dominant, which requires a robust and flexible flotation process to recovery zinc from both sulphide and oxide efficiently.The conventional mineral processing flowsheets have been tested on the LanPing samples taken from the various orebodies by various parties during the past 20 years that includes a sequential flotation flowsheet that was tested in a demonstration plant using the mixed ore. The results of the demonstration plant runs show that the conventional oxide flotation using Na2S and amine collectors could achieve 50 ~ 75% of oxide zinc recovery at very high sulphidiser consumption for the mixed ore but the highly oxidised ore did not satisfactorily respond to the flowsheet in terms of performance consistency and efficiency of oxide zinc recovery, which is very crucial to the overall economics of the project."

Jan 1, 2003

By Matti Kongas, Kari Saloheimo, Antti Remes

"The paper studies the control performance of the flotation process as a function of the measurement accuracy and sampling frequency of an on-stream XRF analyzer, using a simple dynamic model. An additional aim is to assess how the economical result of a mineral flotation process depends on the quality of process control based on the on-line elemental assays.An on-stream XRF analyzer measures the concentrations of slurry lines in a continuous cycle from several process points. The control performance depends on the analytical accuracy and sampling frequency of the concentration measurement. With a long cycle time, the state of the process changes before a new measurement becomes available. With short measurement times the statistical variance of the counted Xray pulses increases, increasing the random error in the analysis. In addition, the measurement accuracy depends on the concentration of the component to be measured from the slurry.To quantify the effect of analysis error and frequency to process control, a simple dynamic process model is created in the Matlab environment. Data from a copper flotation circuit is used as a test case. The process model comprises a first order reaction equation and the grade-recovery -relationship estimated from process data. The control was modeled using the control strategies implemented into a rule based advanced control system. The economical performance of the control was studied by calculating the overall net smelter return at various analyzer parameter combinations."

Jan 1, 2003

By Briony C. Ruse, David V. Boger, Fiona Sofra1

"The sustainability of the mining industry must be addressed through improving tailings management. The use of thickened tailings and pastes stems from a paradigm shift towards designing tailings disposal sites to suit their surrounding environment, rather than manipulating the environment to accommodate the tailings. Thickened tailings and pastes usually exhibit non-Newtonian behaviour, so a thorough understanding of the rheological characteristics of the material is required in order to determine the disposal plant operating conditions.As environmental factors translate into economic issues, minimising waste production using dry disposal methods is gaining popularity. The use of rheological information is of high importance in evaluating the spreading characteristics, the transportation and the dewatering of thickened mineral tailings. The principles outlined may be applied to many industries encompassing a wide range of waste materials. The main obstacle to the widespread implementation of dry disposal methods has been the high initial capital cost of the methods due to the dewatering step, and the high cost of pumping thick suspensions across any great distance. Proper and thorough costing of tailings disposal activities combined with an accounting approach that shows closure and post-closure care costs on a per tonne basis of tailings disposed throughout the life of the tailings facility will show that dry disposal methods are more favourable than they might seem on initial appraisal."

Jan 1, 2003

By D. Whittles, S. Kingman, K. Jackson, S. Bradshaw, N. Miles

The influence of microwave energy at high electric field strength on ore strength has been investigated. Two ores of varying mineralogy were treated in both multimode and single mode microwave cavities. After treatment, any change in strength relative to untreated ore was established. It was shown that in the multimode cavity reduction in strength was related to the applied power level. Results of tests carried out in the single mode cavities showed that, for both ores, reductions in ore strength > 50% could be achieved in very short periods (<1 second). Thermal stress analysis showed that the mechanism of microwave induced failure was the development of tangential stresses at the grain boundaries. It was concluded that operation at 915 MHz with high power and short residence times gives feasible scale-up possibilities.

Jan 1, 2003

Optimisation of the Performance of Flotation Circuits Using a Genetic Algorithm Oriented by Process-Based Rules

Sep 13, 2010

By Manqiu Xu

"Ore grades are decreasing and ore deposits are becoming more complex. In order to make a sound economical decision about a mining project, metallurgical testwork must be carried out. A few large “representative” samples cannot represent the metallurgy of a large ore body and a large number of samples reflecting variation in ore head grades and in mineralization types must be obtained for proper metallurgical studies, including flowsheet development for a greenfield project. A relationship can be established between the recovery of valuable minerals and ore grade for each mineralization type. This relationship can be used to establish a correlation between values recoverable and values contained in the ore body that can include multiple pay metals. With this information, a sound economical decision can be made about the viability of a large mining development project.INTRODUCTIONThe demand for minerals today is historically high as many countries are being rapidly industrialized. The supply for these minerals is not necessarily running short. However, it is widely accepted that the world today is running short of the easy to mine and easy to process ore deposits. As ore grade is decreasing and ore mineralogy is becoming more complex, metallurgical testing must be fully conducted in order to make a sound economical decision about a mining project. For a high-grade and high-quality deposit, it is hard not to make a good profit even with low metal prices. For a low-grade and hard to process deposit, the profit margin is much lower and is dependent on the throughput and the recovery of valuable minerals. The recovery of valuable minerals is a function of ore grade and mineralogy and it must be experimentally determined for a given processing option.At Vale Base Metals Technology Development, metallurgical testing for an existing operation or brownfield project is termed as Ore Evaluation, while metallurgical testing for a greenfield project is termed as Flowsheet Development (Xu, 2011). In the past, metallurgical testing involved a few large composite samples for lab and pilot plant testwork. As ore deposit becomes less homogeneous and more variable, a few large composite samples cannot represent the metallurgy of a large ore body. In addition, useful information about the deposit such as zones of “impurities” or floatable rock minerals would not be obtained. Different processing strategies could have been developed if the locations and sizes of these zones were known in advance. For proper metallurgical studies, a large number of samples reflecting variation in ore head grades and in ore mineralization types must be used. A relationship can be established between the recovery of valuable minerals and ore grade for each mineralization type. This relationship can be used to estimate values recoverable in the ore body that can include multiple pay metals. Ultimately, the recovery verses ore grade relationship will be used in business decision-making."

Jan 1, 2013

By Chuck Edwards

"The development of two large, high-grade uranium projects has been proposed for northern Saskatchewan. The projects are now under review by a joint federal/provincial panel. The McArthur River project is owned by the McArthur River joint venture (Cameco Corporation 53.991 %, Uranerz Exploration and Mining Limited 29.775%, Cogema Resources Inc. 16.234%) and operated by Cameco. Cameco proposes to mill the McArthur River ore at the existing Key Lake mill. The Cigar Lake project is owned by the Cigar Lake joint venture (Cameco Corporation 48.75%, Cogema Resources Inc. 36.375%, Idemitsu Uranium Exploration Canada Ltd. 12.875%, Korea Electric Power Corporation 2.000%). The Cigar Lake joint venture proposes that Cameco operate the Cigar Lake mine for the owners, and that Cogema mill the ore at their McClean Lake mill, now under construction. Proposed systems provide safe mining and ore handling, and allow the milling of McArthur River ore at Key Lake and Cigar Lake ore at McClean Lake. This avoids the disturbance of new sites for milling and tailings disposal.The McArthur River and Cigar Lake deposits are the largest known high-grade uranium deposits in the world. The ore grades at McArthur River and Cigar Lake are at least 100 times those that are mined elsewhere. It is proposed to mine these deposits using remote underground mining methods, to crush and grind the ore underground, to pump a thickened ore slurry to surface, and to transport it in special containers by truck to the mills.During all mining and processing stages the ore is fully contained. Radon emission is controlled by positive ventilation of all process vessels, with the process ventilation backed up by the primary mine ventilation system. Radiation is controlled by heavy steel pipe and vessel walls, concrete walls and sometimes lead sheeting."

Jan 1, 1997

By M. R. Moon

The mine fire at Wilberg Mine in 1984 reached the surface resulting in the failure of the vertical ledge forming the roof and entrance for three main intake portals. The fallen material was covered with a concrete cap to seal the air from the mine. As the mine was recovered and ventilation pressure was placed on seals on the perimeter of the fire area, the concrete capped rubble proved ineffective. Due to the steep and rugged terrain and the inaccessibility to the portals from underground, horizontal holes were drilled into the portal entries and three seals were placed remotely. The seals in conjunction with pressure balancing the seals around the perimeter of the fire area resulted -in the control of the mine fire.

Jan 1, 1993

By A. E. Brugger

SOME 2,000 years ago Pliny is supposed to have said, "Out of Africa always something new." It may perhaps even now be news to a great many that the Belgian Congo has in recent years been producing approximately a quarter of a ton of diamonds annually. For that is what the 1 1/4 million carats, the recovery from 40-odd operating mines, and about 20 or 25 per cent of the world&apos;s normal consumption, amounts to. In 1915, first exploitation operations produced less than 50,000 carats from two mines. The rapid expansion of operations following the Euro¬pean war meant a most rapid development of a virgin land. The interior is now reached by air in one day from the mouth of the Congo River, where steamers unload mail and passengers from Antwerp. This trip formerly consumed 4 to 6 weeks by a narrow-gage, wood-burning, railroad around the rapids of the lower Congo and Livingston Falls; by river boat to the heads of navigation, Djoko Punda on the Kasai or Luebo on the Lulua; and thence by caravan of native porters over narrow-trails to head¬quarters on the Tshikapa. Hundreds of miles of automobile roads have been constructed over veldt and through forest, bridging streams and ferrying rivers. The railway from Capetown to the Katanga copper district to the East, once two months away by trail is now reached in 2 or 3 days over fair automobile highway. Native "boys" who a few short years ago wore little more than a smile and a string of beads and to whom a wheelbarrow was a complicated piece of machinery, are today driving Fords, tending boilers and engines and operating electrical equipment, or are capable mine workmen, machinists and artisans, and dressed in all manner of cast-off white man&apos;s clothing. Even as late as 1920, due to difficulties of securing and transporting machinery during and just after the war, the crudest hand operations were the rule for the excavation, sizing, and concentration of the diamondiferous gravel. All washing and concentration is now mechanized, using steam or electric power, and where operations are sufficiently large to permit competition with native labor costs, excavation and transportation are also accomplished by machinery.

Jan 1, 1932

By J. J. Brown

Wilkes-Barre Meeting, Julie, runs., THE ore-hearth was the earliest type of furnace used in smelting Mississippi Valley lead-ores, which are very pure, and low in silver-content. The first smelters made no attempts to recover lead from the smoke; and since about 15 per cent. of the lead -in the charge escaped in this manner, early practice with the hearth was decidedly wasteful. At most of the large smelting-plants blast-furnaces with auxiliary roasters were substituted for the hearths long ago. But, upon the introduction of the Lewis and Bartlett bag-process for collecting fume, the ore-hearth was used by companies engaged in the manufacture -of pigments, simply on account of the large percentage of fume made by it. In fact, the extraction of lead was kept down by the use of hot blast and other devices. During recent years, however, several smelting companies have realized that the preliminary roasting of galena for the blast-furnace is not economical, and have, therefore, replaced the roasting-furnace with a modification. of the old Scotch hearth, in which a large percentage of the lead in a charge is recovered directly as pig-lead, while the remainder passes partly into fume and partly into slag low enough in sulphur to be charged into the blast-furnace without further treatment. The results obtained have proved so satisfactory, both As to recovery and operating-expense, that one eminent metallurgist has predicted the universal use of the ore-hearth on non-argentiferous ores. The-ore-hearth, thus employed as an adjunct to a blast-furnace plant, is rather a desulphurizer than a smelting-furnace proper,-the chief object being to make a blue slag suitable for the cupola-furnace. Hence, no special care is taken to obtain from it a large lead-extraction. * Head of Department of Ore Dressing and Metallurgy, Oklahoma School of Mines and Metallurgy, Wilburton, Okla.

May 1, 1911

By Ilija Ilic

Recovery of tin from tinplate and production of good-quality detinned-plate for further processing in ironworks has been the subject of interest for many years. Tinplates are mostly used for production of tin containers for food industry and consumer goods. The research carried out so far included determination of the parameters of dissolution of tin from tinplates by alkaline solution of NaOH and electrochemical recovery of tin from the alkaline solutions. During leaching, NaNO3 and methanitrobenzoic acid (MNBA) as oxidants were studied. By leaching the waste tinplate which contains 0.31 % of tin with a solution of 1.12 mol/dm3 NaOH, 0.26 mol/dm3 Na2CO3 and 0.09 mol/dm3 MNBA at temperature of 70°C for 60 mm, a degree of tin leaching of 97 % was attained. MNBA facilitates oxidation of Sn2+ into Sn4+ suitable for obtaining compact, and not spongy, Sn cathode deposit, as it was the ease earlier. Recovery of tin by electrolysis from solutions obtained by leaching was studied to determine the effect of electrolyte composition on the quality of cathode deposit and the degree of electric current efficiency. Experimental results obtained at a laboratory level were checked on an enlarged laboratory set up where continuos leaching of tin from waste tinplate and its electrolytic recovery from the solution obtained were carried out. The experimental set-up -operated under semi-industrial conditions, and about 500 kg of waste tinplate was processed yielding about 1.160 kg of tin (99 % Sn).

Jan 1, 2000